Search Documents

By R. P. Abendroth

This study is concerned with the kinetics of selective oxidation of chromium in a commercial Fe-Cr-Ni alloy. Selective oxidation of chromium in this alloy, by use of a low oxygen-potential atmosphere, leads to the formation of a compact, protective layer of Cr2O3. This layer serves to protect this alloy from gross scaling when it is subsequently exposed to severe oxidizing conditions at high temperature. The interaction of low oxygen-potential atmospheres close to equilibrium with Fe-Cr and Ni-Cr alloys has been studied by others."' These studies werk concerned with the surface-structure variations under slightly oxidizing conditions. NO detailed study was made of the oxide scale formation kinetics, however. The alloy samples were cut from 0.012-in.-thick sheet, with an apparent surface area of 7.1 sq cm. These sheet samples were abraded through 4/0 metallographic paper, and washed in alcohol and acetone. The analysis of the sheet alloy is (in weight percent): 42 pct Ni, 5.5 pct Cr, 0.09 pct C, 0.18 pct Al, 0.36 pct Si, 0.26 pct Mn, balance Fe. The weight gain vs time data were obtained with a 2-g capacity fused-silica spring—cathetometer system. The spring deflection was optically magnified ten times before being read by the cathetometer. A sensitivity of about 0.01 mg was attainable. The spring was enclosed in a water jacket maintained at 60°C to minimize the effect of temperature changes. The sample was suspended from the spring with a fused-silica hangdown and was positioned in the thermal center of a mullite furnace tube. Sample temperature was read with the aid of a thermocouple placed outside the mullite tube and an inside vs outside temperature calibration. Temperature change during the course of a run was ±0.25°C, with a temperature gradient of less than l.O°C over the length of the sample. Total temperature uncertainty was no more than ±3.0°C. Alignment difficulties between the hangdown and radiation shields in the furnace tube required that the sample be positioned in the furnace when cold, and heated with the furnace until the temperature stabilized at the desired point. This required 5 to 6 hr, and was carried out in Matheson ultrahigh-purity hydrogen. Oxidation was started, after evacuation, by introducing a hydrogen-water vapor mixture, obtained by saturating hydrogen with water vapor at 31.00o ± 0.02oC. Oxidation was continued for 90 min. Gas flow was 300 ml per min during heat up and oxidation. Since only several milligrams of oxide are formed on each sample, chemical analysis of the oxide is difficult. A representative analysis is: 80 pct Cr2O3, 5 pct Fe2O3, 3 pct Al2O3, 4 pct MnO, 7 pct SiO2, 1 pct or less NiO. X-ray diffraction analysis of the oxide as formed on the alloy gives rhombohedra1 Cr2O3, and barely distinguishable amounts of a cubic spinel phase, and possibly AlZOs and SO2. The identification of these latter two compounds is by no means certain. The spinel phase could be based on iron or manganese as these elements are present in significant amounts in the oxide. The results of the kinetic studies using 31°C dew-point hydrogen-water vapor mixtures were found to conform to a parabolic rate law. In many cases the parabolic plot consisted of two intersecting straight lines, defining an early and a late rate for a particular run, and in the other cases the parabolic plot consisted of one straight line for the entire run. The slopes of the various straight lines were determined by the method of least squares. Reproducibility of the data was good enough for multiple runs at the same temperature such that the value given for the rate constant is the average for two or more closely similar values, rather than widely varying values of the rate, where more than one determination is indicated in Table I. The exhibition of only one or of two rate constants during a run can happen at the same temperature. Thus, Table I shows that at 11'74°C a single rate constant was obtained from one sample, while other samples oxidized at the same temperature gave an early and a late rate constant. It should be noted that the single rate constant corresponds very closely with the early rate constant. This is also true at 1153°C. The time at which the late rate started to appear was variable, usually occurring 20 to 40 min after oxidation had started.

Jan 1, 1964

By E. P. Klier

THE work of Klier and Lyman1 on the bainite reaction has led to the full description of this reaction for medium-carbon low-alloy steels. Certain experimental data reported by Klier and Lyman appear, however, to be improbable of obtaining in very high-carbon steels. The study herein reported consists of an analysis of the transformation characteristics of a 3 per cent chromium, 1 per cent carbon steel by means of X-ray and metallographic methods. From the results obtained it is concluded that the bainite reaction in this steel is more complicated than that reported by Klier and Lyman for the low-carbon low-alloy steels. However, the mechanism of bainite formation in this steel appears to be essentially the same as proposed for the low-carbon low-alloy steels with the modification that the first volumes to transform are carbon-rich rather than carbon-poor. EXPERIMENTAL PROCEDURE The analysis of the steel studied was: Cr, 2.89; C, 1.02; Mn, 0.33; Si, 0.35; S, 0.012; P, 0.020. The stock was received from the Carpenter Steel Co. in rolled bars. Specimen Preparation Specimens were austenitized at 1200°C. (2192°F.) for 25 min. in purified nitrogen. The resultant A.S.T.M. austenite grain size was 0-1. Isothermal transformation was allowed by quenching the specimens into liquid metal baths controlled to ±5°C. at 540°C. (1004°°F.) and above, and to ±2°C. at 490°C. (914°°F.) and below. Following the desired degree of transformation all specimens were water quenched. Metallographic Examination Specimens 1/4 in. round by 1/4 in. were used for metallographic examination. Etchants used were Vilella's reagent (1 gram picric acid, 10 ml. hydrochloric acid to make l00 ml. ethyl alcohol solution) and alkaline sodium picrate (electrolytic). Vilella's reagent was effective in revealing all microconstituents, while the alkaline sodium picrate developed the carbon-rich structures or carbides only. X-ray Examination Two X-ray techniques were used-the Debye-Scherrer method and a back-reflection method. The small specimens necessary for the Debye-Scherrer method were austenitized and then allowed to transform, or were cut from the larger metallographic specimens. The metallographic specimens were used for the back-reflection X-ray analysis. When it was desirable to determine the structure of the carbide present, sliver specimens were electrolytically etched to develop a carbide coating, then were exposed in the cameras. This technique was frequently necessary to allow positive identification of the carbide.

Jan 1, 1945

Determine the effectiveness of remining operations in reducing contaminant load (acidity, iron, and sulfate) of discharges emanating from abandoned surface and underground coal mines. Background Until the implementation of remining initiatives, most States had regulations that held the operator remining an abandoned site responsible for preexisting acid mine drainage (AMD) discharges. For example, if a mining. company wanted to remine an area hydrologically connected to an existing AMD discharge, the company became responsible, as soon as the site was activated, for treating that discharge to meet effluent standards. If the mining operation improved the quality of the discharge, but the discharge failed to meet effluent standards, the company was held accountable for perpetual treatment. Because of this regulation, most mine operators avoided abandoned sites with minable coal reserves and AMD discharges. However, changes in remining legislation allow coal companies to be released from treatment liability as long as the post-remining pollution load does not exceed the pre-remining level. If remining can improve water quality through improved mining and abatement techniques, abandoned mine land (AML) areas that previously were liabilities could become

Jan 1, 1994

By Samuel H. Dolbear

THE value of a mine is basically dependent on its capacity to yield profits. Since the ore must be mined, treated, and sold, some of it in various future years. there is a risk involved as to future costs, selling price, and working conditions. It cannot be expected that the economic condition existing at the time of valuation will continue unchanged for long periods in the future. During the past 20 years, mineral production in the United States has been conducted under a changing economy in many respects more exacting than that applied to other businesses. There have been increased production incentives, technical aid, exploration of privately owned mineral deposits by government at federal expense, and liberal loans for development and equipment, with risk partially assumed by government.. Some of these benefits have been counterbalanced by price ceilings, consumption controls, and stimulation of competition from foreign producers who have been offered the same advantages extended to American operators. For the present, mines will operate under a government policy directed toward reducing federal aid and control. The tenure of this change will depend upon future elections and the status of foreign relations. War and threat of war are now of the most vital significance to the mineral industries. Other factors which influence cost of production, markets, and price of mine output might be classified as Acts of God or Acts of Government. In some countries expropriation and the difficulty of exporting earnings or investment returns are risks that must be considered by foreign capital. Recognizing that this retards American investment in foreign countries, the Mutual Security Agency offers insurance against such expropriation and guarantees the convertibility of capital and profits. Since it is impossible to predict with certainty either cost of production or selling prices of metals for long periods, some assumptions must be made as to profits in the future. The basic assumption must be that the price of the company's product will vary in proportion to changes in operating cost. There is often a lag in this reaction, however, for prices of minerals are generally more sensitive to declines and less sensitive to increases than are costs. This reflects in part the resistance of labor to downward wage revision and a corresponding alertness in realizing its share of price advances. Some labor contracts include automatic adjustments to metal prices. Notwithstanding the complexity of the, problems involved and the difficulty of weighing their effect on value, such risks may be appraised with reasonable accuracy and a rate of earnings adopted that is compatible with the risk. It is, of course, possible to revert to a yardstick of value such as the commodity dollar, which has been advocated from time to time, but while revaluation in 1933 disturbed public confidence, the theoretical gold dollar continues to be the standard of greatest stability. Its gain or loss in purchasing power is reflected ultimately in cost of production and selling price of the mine product. At present 35 dollars are allocated to one ounce of gold. Measurement of Risk In the application of the Hoskold and most other formulae, a yearly dividend rate commensurate with the risk involved is set aside out of annual earnings. If the risk is great, this rate may be 15 to 25 pct of the amount invested. The remainder is placed in a sinking fund invested in safe securities such as high grade bonds or conservative equities, and the interest or dividends from these securities are added to the sinking fund. The sum of these sinking fund payments and the compounded interest at the end of the mine life is taken as the value of the mine. Admittedly the decision as to the size of the risk rate is the most difficult element in valuation and one requiring the most exacting consideration. It is necessary to look years ahead in an effort to determine future costs, market prices, demand, competition which may develop, including that of substitutes, and other influences common to the mine and to the region in which it is situated. Another phase of risk is the enactment of unfavorable legislation, taxes, and what appears to be an alarming spread of nationalization and expropriation. Capital is sometimes borrowed from the government to finance strategic production. Such loans may be collectable only out of production and involve no liability otherwise. Valuation in these cases must recognize the effect of such a reduction in liability. Offsetting some of these risks are the possibilities of mechanization and other cost-reducing discoveries, improvements in mining and treatment methods, new uses for minerals and metals, and normal growth of markets. In this paper, the terms risk rate, dividend rate, and speculative rate are synonymous. Safe rate and redemption rate are also used interchangeably. These alternatives are used here because they are commonly found in the literature on mine valuation. In Michigan, the State Tax Commission has long employed a risk rate of 6 pct in its valuation of iron mines. There the outline of reserves is well established and operating costs and conditions are based on adequate experience. The following comment on rates appears in the report of the Minnesota Interior commission on Iron Ore Taxation submitted to the Minnesota Legislature of 1941.1 Most engineers agree that 7 percent for the specu-lative rate is "an absolute minimum". C. K. Leith in

Jan 1, 1954

By Lee Sung-rock

KIGAM (Korea Institute of Geoscience and Mineral Resources) has been doing various kinds of research works in marine minerals and energy resources exploration and utilization since early 1990s in Korea. In the presentation, the authors will introduce the recent research and development activities mainly focusing on the rare earth metals of the Pacific deep seabed Mn-nodules and gas hydrates which occur from Korean deep waters. KIGAM has been participating in the polymetallic manganese nodule exploration, mining and metal-extraction project, which is modulated by KIOST (Korea Institute of Ocean Sciences and Technology, formerly KORDI). Now KIGAM puts more focus on extracting precious and rare earth metals from the Mn-nodule as well as underlying sediments. The rare earth elements (REE) from seabed mineral deposits also draw attention to those countries including Korea which are lack in natural resources. KIGAM is doing several kinds of leaching experiments using various kinds of reagents under the different experimental parameters. Extraction of rare earth metals from deep sea nodule using H2SO4 and HCl solution showed good leaching effect. As the gas hydrates are to be evaluated as a new future energy resource globally, Korean government has initiated national R/D program covering fundamental exploration survey for resources assessment in Korean deep waters and production technology development. KIGAM plays a key role in seismic exploration, resources assessment, experimental

Sep 14, 2011

By H. Saeedi Ali, A. J. Monhemius

"Anglo Asian Mining’s Gedabek mine is situated in the Lesser Caucasus mountains in Western Azerbaijan. The ore body is a complex copper-gold porphyry deposit, comprising intermixed oxidized, transition and sulphidic gold and copper-bearing ores. Gold in the sulphide ores is generally not refractory and is recoverable by cyanide leaching, but the secondary copper minerals, which are also cyanide soluble, lead to high cyanide consumptions. Ore processing at Gedabek is by agitation leaching for high grade ore (>1g Au/t) and heap leaching for lower grade ore. In order to cope with the high copper concentrations in the cyanide leach liquors, a unique combination of resin-in-pulp for selective gold extraction and SART processing for copper removal and cyanide recovery is used. In 2015, a flotation plant was added to treat the tailings from the agitation leach plant before the tails are sent to the tailings dam. This plant produces a copper sulphide flotation concentrate and also recovers some of the residual gold and silver in the tailings. Since February 2017, due to lower grades of gold and higher copper in the feed ore, the decision was taken to alter the flow sheet and to carry out flotation ahead of agitation leaching, to reduce the cyanide consumption during leaching by removing soluble copper minerals. The paper compares and contrasts the performance of the plant in the two configurations, namely, (i) leaching followed by flotation and (ii) flotation followed by leaching.INTRODUCTION In May 2009, Anglo Asian Mining started open pit mining for gold on its Gedabek property in the Lesser Caucasus Mountains in western Azerbaijan. Gedabek is situated on the highly mineralized Tethyan Belt that runs from the Himalayas to the Balkans. The ore body at Gedabek is a complex copper-gold porphyry deposit, comprising intermixed oxidized, transition and sulphidic gold-bearing ores. The sulphidic ores contain mainly pyrite and chalcopyrite, with some secondary copper sulphide minerals, such as bornite and chalcocite, and minor amounts of sphalerite, galena and tetrahedrite. Gold in the sulphide ores is generally not refractory and is recoverable by cyanide leaching, but the secondary copper minerals, which are also cyanide soluble, lead to high cyanide consumptions and passivation of free gold."

Jan 1, 2017

By Charles H. McGuirk

The movement of iron ore, limestone and-coal on the great lakes involves an intricate transportation network between mine, dock, vessel, railroad and consumer. The system requires that stockpiling be performed at certain points in the pipeline because of the seasonal closing of the lakes, traditionally, this has been accomplished at origin and destination with a substantial cost. Impact to both the shipper and consumer, From the time that the raw material is removed from the ground, expeditious handling and movement to final destination is threatened by a series of potential delays. An initial movement from mine or processing plant to the upper lake port must be coordinated between rail equipment and dock facility, As each vessel is loaded, a schedule must be developed which routes the cargo to an unoccupied lower lake port. However, if the vessel is not delayed by unpredictable weather conditions on the lake, the boat may still arrive at a port congested with other vessels awaiting their turn to unload.

Jan 1, 1973

By Thomas P. Meloy

There is much interest in the automation of entire comminution circuits, At the present technological level it is possible to automate a circuit but to date it has not been done, To successfully automate a circuit, a number of problems must be solved. Not all of them are engineering problems. The purpose of this paper is to discuss some of these problems, as certain the implications of these problems and indicate solutions to them. In this paper the term "automation" is used loosely but in the popular sense. Namely, that a plant is automated if a computer is used to control the basic flow of the materials as well as setting the critical parameters in the process. Specifically, the discussion will concern itself with the control of comminution circuits from the dumping of the ore into the primary crusher until the final interface between the comminution circuit and say, the flotation mill in the case of a sulfide ore.

Jan 1, 1965

By Isabela Leao Amaral da Silva, Felipe Perisse Duarte Lopes, Alice Barreto Bevitori, Sergio Neves Monteiro

"Jute fibers have in the past decades being investigated as possible reinforcement of polymer composites. However, information is still needed on the fiber interaction with a polymeric matrix for a complete evaluation of the capacity of load transference inside the composite. The present work investigated the interaction of jute fibers with polyester matrix by means of the critical length assessment through pullout tests. Tensile tests of polyester sockets embedded with different fiber lengths allowed the critical length to be determined and then the interface shear stress to be calculated. A relatively low interfacial strength was found, which indicates a weak adhesion between the ramie fiber and the polyester matrix. The SEM analysis of pulled out fibers corroborates this result.Introduction Natural fiber, mainly those lignocellulosic extracted from plants, have, in the past few decades, attracted the attention not only of scientists but also of industrial technologists of our society interested in their engineering applications. As it is well known, uses of natural fiber in clothes carpets, baskets, ropes and low cost construction roofing has existed from the beginning of our civilization. Today environmental and energy saving issues are motivating research works on new uses of lignocellulosic fibers in polymer composites [1-6]. Moreover, industrial application of lignocellulosic fiber composites are already in technological sectors such the automobile industry, packing and civil construction [7-9].In addition to environmental, economical and social benefits, some lignocellulosic fibers present specific properties that are comparable to those of other synthetic fiber used for polymer composite reinforcement. For instance, the specific strength (GPa.cm3/g) of curaua (1.31), sisal (0.92) and ramie (0.93) fibers, from results obtained with very thin diameters [10] are relatively closer to that of glass fiber E (1.33). Therefore, in principle, it would be technically justified to replace glass fiber, which is more expensive, toxic and represents a problem to the environment [ll], by a strong lignocellulosic fiber. However, serious drawbacks such non-uniform dimensions and heterogeneous properties [6] as well as the tendency to form aggregates during processing and incompatibility with a hydrophobic polymer matrix, reduce the potential of lignocellulosic fiber to be used as composite reinforcement [1-6]. In particular, a low interfacial strength causes a weak adhesion between the hydrophilic fiber and the polymer matrix."

Jan 1, 2011

The paper outlines the development of a solvent extraction process for the recovery of scandium, yttrium, thorium, and heavy lanthanides from waste sulphate liquor at the Port Pirie uranium treatment plant. A summary is given of known solvents for these elements, including the recently developed alkyl-phosphoric acid esters which are applicable to sulphate solutions.A kerosene solution of di- (2'-ethylhexyl) phosphoric acid (EHPA) has been suggested by some workers as a suitable solvent for fractionation of the lanthanides. Experimental work with this solvent showed that it could be used for initial recovery of the above elements from low concentrations in the complex sulphate liquor. In particular, scandium could be recovered as a high grade product by extraction with 0·lM EHPA, followed by a purification strip with 9N sulphuric acid, and final stripping of scandium with sodium hydroxide solution.To enable alkaline stripping to be used successfully, the kerosene solution of the reagent was modified by the addition of a small proportion of nonanol. Experimental work included laboratory scale batch tests and small pilot scale continuous tests.A proposed extension of the process for the separate recovery of individual heavy lanthanides, yttrium, and thorium is described.INTRODUCTIONAt the Port Pirie uranium treatment plant of the South Australian Government, large volumes of "barren liquor", free from 'uranium, are at present run to waste. This "barren liquor" results from sulphuric acid leaching of Radium,Hill uranium concentrate, followed by separation of solid residues and removal of uranium from the clear solution by ion exchange. The mineral davidite, from which the uranium is derived, contains other potentially valuable components, notably vanadium, chromium, thorium, yttrium, scandium, and the lanthanides. These constituents are...

Jan 1, 1961

By Lucia Vieira

Kelvin probe force microscopy (KPFM) can be used to monitor electrostatic charges on the surfaces of materials. In this paper, we describe the use of KPFM to evaluate the electrostatic effect induced by silver nanoparticles incorporated as clusters in diamond-like carbon (DLC) films, before and after scratching. The results are compared to those obtained for DLC films without silver nanoparticles. Raman spectroscopy was used to identify the DLC signature, and energy dispersive X-ray spectroscopy (EDX) was used to confirm the presence of silver in the film. The morphology of the DLC film containing silver was investigated using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The findings suggest that the incorporation of silver nanoparticles in amorphous materials could offer new options for electrostatic energy storage on the surfaces of these materials.

Jul 31, 2018

By M. J. Spendlove, P. P. Zapponi

"INTRODUCTION In carbothermic processes for the production of magnesium, magnesium oxide is reduced by carbon according to the following equation:(1) MgO + C = Mg(g) + CO.The reaction is virtually complete at temperatures above 2,000° C. but reverses rapidly at somewhat lower temperatures. To produce magnesium by this reaction, therefore, it is necessary to cool the gas very rapidly to a temperature at which the rate of the reverse reaction becomes negligible. Several media for quenching the gas have been proposed, among which are hydrogen, natural gas, liquid hydrocarbons, and molten metals of low melting point.The results of a preliminary investigation on the use of molten lead as the quenching medium are summarized in this report. The work was done in 1941, when the threat of war made it imperative to investigate every process that offered possibilities for rapid expansion of domestic production of magnesium. Although the results were encouraging, other processes appeared to offer better prospects for immediate wartime development, so the work was not continued. Shortly before the investigation was completed, several patents on the use of low-melting metals for absorption of magnesium vapors appeared, 4/"

Jun 1, 1947

By Sheldon P. Wimpfen

EVERYWHERE in mining circles the talk is of this new development of hard faced or insert bits which hints of many changes to come in mining practice and rock drill equipment. In the past fifteen years new equipment has appeared in rapid succession which brought one change after another in rock breaking practice. Detachable bits were an innovation which met with wide success. Blasthole diamond drilling has proven itself. Only recently, fusion piercing was announced as a possible solution to the problem of breaking taconite ores. For several years this interest in new methods has been growing and various experimental usages of tungsten carbides in rotary type rock drilling bits have been partially successful. American experts in rock drilling have been concerned with the subject for ten years but actual commercial practice was begun by European manufacturers and mining companies. At this time nearly every manufacturer of rock drilling bits is working on some type of an insert bit. On the Rand, European manufacturers are testing out various types of insert bits. The problems relating to rock drilling in South Africa vary greatly from ours. The bulk of the drilling there is limited to the 31/2-ft holes that are drilled for breaking the gold bearing reef ore. Rock drilling in most mines is far more diversified. Both drifting and ore breaking call for holes varying in length from 4 ft up to as much as 50 ft and more.

Jan 1, 1947

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite having length to diameter ratios of 3:1, 2:1, 1:1, and 0.5:1 were broken in axial compression to determine whether lateral end constraint affected the breaking strength. Steel rings bonded to the ends of the model pillars with epoxy provided, during the loading cycle, a lateral end constraint of about 17 to 30 percent of the average axial stress. The effect of this constraint was to increase the breaking strength of the rock as compared to cylindrical pillars without constraint. The percentage increase in breaking strength varied with rock type and increased as the length to diameter ratio decreased. The maximum increase in breaking strength was 35 percent for marble pillars having a length to diameter ratio of 0.5:1. A theory was developed which relates the expected constraint to the physical properties of the ring and rock.

Jan 1, 1968

By Jorgen Elbrond

In a stream of ore in an underground mine or in a beneficiation plant bins are installed between machines or machine system. When the upstream machine is stopped the downstream machine can continue operation for a while and vice versa. The paper describes a procedure for calculating the total capacity of a system consisting of two machines with an intermediary bin as a function of the bin's live volume and of the installed machine capacities and their production variations, which are defined. Extensions to several machines in parallel and in series are shown as well as practical examples.

Jan 1, 1982

By Irving Hartmann

The record of safety in the use of permissible explosives in United States coal mines has been excellent, due in great measure to the persistence with which research has been carried on in the Bureau of Mines, to the development of permissible explosives, and to the cooperation of mine operators and workers in using permissibles in a recommended manner and in the effective though gradual replacement of black powder and other nonpermissibles. The demand for increased rate of coal production, changes in mining conditions and minim methods, and introduction of new mining machinery have resulted in modified or new blasting practices. To keep abreast of these developments the Bureau of Mines conducts investigations under actual mining conditions at the Experimental coal mine near Pittsburgh, Pa. Several years ago an extensive study was complete to determine conditions under which the allowable charge limit for permissible explosives per shot hole might be raised from 1.5 to 3 pounds without undue risk of gas or coal-dust ignitions. As a result of the study, this increase in the charge limit was authorized under certain specified conditions in 1948,5/ greatly facilitating production schedules.

Jan 1, 1954

By J Furtney, W Fu, D Nutakor, A Brose

Rock blasting outcomes are often a shared responsibility of both the mine operations group and the mine geotechnical group. From an operational logistics and planning perspective, blasting concerns include optimal fragmentation for subsequent crushing, ensuring the blast is energetic enough to allow easy digging, and understanding the effect of muck from a previous blast on the current blast. From a geotechnical perspective, wall damage and catch bench capacity are the primary concerns. Other concerns for both teams include damage to mine infrastructure by fly rock or blast-induced vibrations, and the stability of open stopes under the pit. This work presents two blast modelling applications (or ‘apps’). The basic app instantly gives fragmentation and wall damage predictions for a given generic blast design. The advanced app loads the current pit contours, reads the blast design from a spreadsheet, and calculates the expected vibration magnitude and peak frequency. The apps have been developed specifically for the Rio Tinto Borates and Lithium Mine in California and are used to support blast design between the operations group and geotechnical group. The basic app instantly gives fragmentation and vibration predictions given a blast design by combining the Kuz-Ram fragmentation model with the scaled distance model for vibrations. The advanced app uses the signature hole method. Blasting outcomes at the mine have improved since using the apps.

Jun 22, 2022

By Valdeci Paula Alvarenga, Sergio Luiz Costa, Itavahn Alves da Silva, Filipe Bueno Carvalho, Varadarajan Seshadri, Carlos Antonio da Silva

Use of fluorspar in steel refining operations is one of the environmental concerns and as such reduced consumption of this material or substitution of the same is one of the objectives. Industrial runs were carried out at Aperam Steel making convertor unit (Timóteo, MG, Brazil) using recycled/briquetted slag for partial or complete substitution of fluorspar. Samples were collected from the metal bath and slag after oxygen blowing to assess dephosphorization with several combinations of recycled/briquetted slag and fluorspar. The results showed that partial substitution of fluorspar by BOF slag briquettes did not affect the efficiency of dephosphorization. In general average Phosphorus content was reduced to 0.010% in the case of partial substitution compared to 0.016% in the regular refining procedure with no substitution. This replacement also resulted in 40% reduction of the fluorspar consumption in the converter

Jan 1, 2015

By Peter G. Sechiari

The Rio Tinto-Zinc Corporation Limited (RTZ), through it exploration company Riofinex, commenced exploration for bauxite in the Amazonia region of Brazil during 1970. Following' encouraging indications, exploration licences were taken out and an exploration programme was initiated In February 1975, a preliminary 'feasibility report indicated that a project, based on the Miltonia plateau located close to the town of Paragominas in the State of Para, was viable and that barging might offer an economic solution to getting the product to an ocean-going port. A, decision was taken in April 1975 to proceed with a full feasibility study. In the latter stages of the study, an engineering consortium of Mendes Junior and Bechtel do Brasil was employed to review, and modify if necessary, the concepts that RTZ had developed for the project's operation. With these concepts agreed, the consortium was requested to make capital and operating cost estimates, and these became available during February 1978. The deposit is being developed by a Brazilian company Mineracao Vera Cruz S.A. (MVC) in which the present share-holding is owned 64 percent by RTZ and 36 percent by Companhia Vale do Rio Doce (CVRD). RTZ is a British based international group of mining and industrial companies with interests in almost every major metal and fuel. CVRD is a Brazilian mining company, 85 percent owned by the Brazilian Government, with a major interest in iron ore and also other non-ferrous metals. It is intended, in due course, that the company will become majority owned by Brazilian interests.

Jan 1, 1979

By Leonardo Camilo dos Reis, Edmilson Fernandes Dadomi, Claudio Silva de Paulo

In the hot strip mill production, one of the factors that may affect the productivity is the occurrence of failure due to the geometry of the strip at the exit of the rolling mill, because the tip of the strip can turn-down or turn-up. This study had the objective of evaluating the behavior of the strip when leaving the working rolls, through numerical simulation, aiming to know the influences of the main variables that govern the formation of the turn-down. The methodology consisted in performing the computational simulation of the strip mill and to vary the operational and geometric parameters that could influence the process. The results showed that the rolling of hot strips of HSLA material with final thickness varying between of 3 to 6 mm and a reduction of 6.6% to 11.0% in the last stand of a hot strip mill, tends to bend towards the roll with larger diameter, higher friction coefficient , higher temperature and lower limit of material flow. It was observed that the variation in diameter is the main factor that contributes to the formation of the curvature of the front-end of strip. Based on these results, several measures were implemented in the industrial line, with a significant reduction in the occurrence of turn-down.

Oct 2, 2019