Search Documents

By Peter G. Zambas

In planning an underground room and pillar mine, the selection of the shaft or portal location and the orientation of the main haulage arteries is of paramount importance, particularly in view of the high dependence of the cost of truck haulage on the proper definition of these parameters. In an effort to facilitate this selection a computer program was written which, by relating the truck characteristics to the areal configuration of the property or ore-body, derives the volume-weighted total fuel and time requirements for hauling ore from every panel within the property to a specified portal or shaft location through a predetermined gridwork of haulage drifts. By varying the size and orientation of the gridwork and the location of the portal or shaft access, an infinite number of configurations can be investigated. The results of this analysis can be plotted to indicate the optimum conditions.

Jan 1, 1971

By George A. Savanick

Borehole (slurry) mining, in which a tool incorporating a water-jet cutter and a downhole slurry pump mines phosphate through a borehole, was field tested in northeastern Florida as part of a Bureau of Mines program to increase the domestic availability of critical minerals. Approximately 1700 tons (1.54x106 kg) of phosphate ore were mined at 40 tph (10.1 kg/s) from a depth of 250 ft (76 m). The borehole was filled with water during mining for roof support and to assist slurry pumping. Underwater cutting was enhanced with an air-shrouded water jet. Mined cavities were backfilled to prevent subsidence after abandonment. Roof subsidence during mining was avoided only when the cavity was filled with water. Environmental monitoring before, during, and after mining included hydrological studies and measurements of water quality. Significant water quality changes occurred only in the zone being mined and were confined to the immediate area of the borehole.

Jan 1, 1983

By Patrick R. Taylor

Thermal plasma technology has a wide range of applications in extractive and process metallurgy. Beneficiation of complex ores, oxide reduction, melting/remelting of refractory metals and scrap, and the recovery of precious metals from waste products are some examples of potential uses for plasma technology. The highly concentrated enthalpy provided by plasma torches is a cleaner energy source and may give higher processing rates per reactor volume than conventional technologies. Some of the other advantages may be: controlled furnace atmosphere, ability to treat fine feed materials and rapid quenching. A review of some of the uses for plasma processing in non-ferrous process and extractive metallurgy is presented.

Jan 1, 1993

By P F. Knights

Mining companies are striving to achieve new levels of operational maturity and drive process improvement across the organisation in the face of unprecedented demand and limited supply of experienced human resources. Advanced analytics techniques can help overcome these fundamental challenges by applying data techniques not previously applied in mining. Today, decisions are usually locally optimised but do not achieve optimum capability for the value chain. Although more information is collected then ever before, it is difficult to link many sources of data together in the same place in real-time, for example plant history, maintenance, mine planning, logistics and engineering data. Consequently complex analysis of data is time consuming and requires specialist skills and knowledge, and is often neglected in the decision-making process. In the future, analytics will close the loop between analysing data and taking action. Analytics will become embedded in the business and routinely applied to improve decision making across the organisation, from senior management to operations and maintenance workers, but will not require specialist skills or be time consuming to analyse data. As analytics becomes embedded in the business process, decisions are supported by data (not on gut feel), and critically, data from many sources are integrated in real-time to improve the quality of decisions. Ultimately, predictive tools will help suggest, or even in some cases automate, courses of action. The main opportunities for analytics exist where the enterprise requires supporting technology to enable it to continue to evolve to higher level of maturity. This will be in the areas of asset management, rapid reconciliation and adaptive planning, and the inbound and outbound supply chains. Advanced analytics are also a key enabler for increasing the effectiveness and realising the true value of Remote Operations Centres to safely and efficiently support operations in remote locations with smaller workforces.

Jan 1, 2008

"""Hazard"" is the general expression used by safety engineers to denote risk, or the danger to property or human beings from the contingencies peculiar to different industries. Where a business, family, or individual is subjected to possible financial loss from any particular hazard, it is customary and is considered good practice to insure for reimbursement of possible loss. Accordingly, we take out insurance for earthquakes, for fire, for accidents, etc., and are charged a different premium for each. The premium rate is based on our relative exposure to the hazard in comparison to the total loss to our particular class of business in our geographical location over a given period.Insurance, then, must be considered as the experience of a group rather than of an individual, and any individual may be fortunate or unfortunate over stated periods. Through the law of averages, the probability of loss because of exposure to hazard is becoming more accurately measured as experience is accumulated and data are analyzed.Lion human life came to have a financial value in the eyes of the law, and employers were held liable for losses through accidents to employees while on duty, insurance companies began to underwrite the accident risks of the different employers and divided them into classes based on the amount of risk involved. Premiums for compensation insurance are based on relative exposure, which is measured by pay roll. The premium is rated in proportion to the severity of losses established by statistical studies.' It soon became evident that the accident experience of employers in the some industry varied widely; that is, there were good and bad risked in the same line of business. This resulted in ""experience rating"" of premiums, meaning thereby that an employer with experience in accident cost was premium rated in proportion to his losses over a stated period (usually three or more years)."

Feb 1, 1926

By Sherwin F. Kelly, Bela Low, William B. Creagmile

Electrical methods and instruments for geophysical exploration have been almost exclusively applied, during these years of development of the art, by a few companies specializing in this field. The control of patents, the cost of the instruments and the general lack of published information on details of field procedure and office interpretation have given these owners a monopoly in carrying out electrical surveys. The development of the Megger Ground Tester1 seems likely to change this situation, and to enable mining engineers and geologists, without special training in geophysics, to carry out simple reconnaissance electrical surveys. Nevertheless, the need for such special training and experience in planning surveys and interpreting their results remains, and probably i always will remain, indispensable for a successful outcome. The unique thing about, the Megger Ground Tester, which gives rise to this hope for its general use, is its simplicity of operation. The four binding posts of the instrument are connected by insulated wires to four stakes driven into the ground at appropriate points. The crank of the Megger is then turned, and the resistance of the ground between the two inside stakes is read directly, in ohms, by the deflection of a pointer over a scale. The apparatus is shown in Fig. 1. Fundamentally, the principle of operation is that of determining the resistance of a four-terminal conductor, as applied by Frank Wenner to the measurement of earth resistivity. "A four-terminal conductor is a conductor provided with two terminals to which current leads may be connected and two terminals to which potential leads may be connected. The resistance of such a conductor is the difference in potential between the potential terminals divided by the current entering and leaving

Jan 1, 1932

By Stephan Fisch, Franz-Werner Gerressen

"The use of cut-off-walls (COW) for the open pit coal mines has been used for decades. They have been used to reduce the negative hydraulic impact to the surrounding area caused by the open pit mining. The pile-guided trench cutting system is a worldwide unique technique, originally developed by the engineers of the mining companies themselves. It guarantees a continuous, joint free, COW during a continuous installation process. At this specific site in Welzow, this technique has been pushed to new limits in order to address the local lake region. Depth capability has been designed to about 430 ft (130m), proven are already depth of about 360 ft (110m) at a constant trench width of 39 inch (1000 mm). This project is approximately. 6.8 miles (11 km) long of COW, scheduled to be completed in 12 years period. About 2.05 miles (3.3km) have been installed, which is equivalent of about 3.5 Million ft² (330,000 m²). The system flushes special clay which forms a filter crust at the inner surface of the trench. Only natural clay resources used, in order to achieve the cut-off effect (colmation effect). The paper explains the installation process of the cut-off-wall as well as the equipment systems developed specifically for this project. After a successful start of the first phase of the project, the next step in the advancement of the equipment is already underway to enable the installation of greater depth to approximately 490 ft (150 m +) and beyond. The next generation equipment system is scheduled to start operation around 2018 INTRODUCTIONThis Serbian saying “Bóh je stworil Lužicu a cert je zaryl brunicu – God created Lusatia and the devil buried brown coal underneath it.” captures local communities’ ambivalence towards lignite.Lusatia is an almost entirely flat stretch of land between the Elbe and Neiße rivers dominated by glacial sands. On the surface, the heathland and woodland is hardly noteworthy. However, three large lignite mining regions, two in Brandenburg and one in Saxony, in the east part of Germany, divert the attention to underground level, down to depths of up to 120 meters. Here, seams crisscross the earth like ribbons. They were formed in the Tertiary around 17 million years ago.The mining of the lignite started almost 200 years ago. To enable open pit mining, a suitable dewatering system was required. At first, wells and drainage system were used. With the increasing demand to go deeper to enable full use of the existing resources with greater mining depth, a decision taken back in the 60th of the last century, the amount of water which had to be pumped increased dramatically. In peak times, approx. 1.57 Billion cubic yards per year (1.2 Billion m³/year) had to be pumped. This led to a lowering of the groundwater level for up to 230 ft (70 m), impacting the regional lake landscape. In order to reduce the influence on the water balance, and bring the water level back to pre1970th, a first development took place to implement the use of specific COW system to depth of about 147 ft (45m)."

Jan 1, 2017

By Chinmay Shingote, Robert Visintainer, Renjie Ke, Jaikrishnan R. Kadambi, John Furlan

Hydrocyclone separators are widely used in various industrial applications in the oil and mining industries to sort, classify, and separate solid particles or liquid droplets within liquid suspensions, which are considered to be multiphase systems. Numerous valuable studies have been conducted in recent years to investigate the flow fields inside hydrocyclones. However, much of the information regarding the performance of cyclones in the literature has limitations and much of it cannot be considered as completely applicable to most real-world applications; many of the studies investigated the flow fields within extremely simplified hydraulic designs that are not representative of the complex geometries or large sizes which are typical in industry. Therefore, in this study, the two-phase flow system inside the actual hydraulic geometry of a milling circuit hydrocyclone is explored with the aid of both computational and experimental techniques (particle image velocimetry (PIV)). More specifically, the flow field with an air core has been investigated. In addition, the air-liquid two phases flow in a hydrocyclone might cause some challenges on both the computational and experimental sides. Two turbulence models are utilized in the numerical calculations: the Reynolds stress model and large eddy simulation. The computational studies are mainly focused on the local flow behavior and the prediction of the dimensions and shape of the air core. Different section planes of hydrocyclone are selected as planes of interest and divided into several fields of view (FOV) for PIV measurements. Two-dimensional experimental velocity vector maps are obtained in each of the fields of view. The computational results are validated globally using pressure and flow rate readings at the boundaries and locally by comparison to the PIV velocity vector maps and profiles.

By Sibin Zhang, Shengli Wu, Youhao Yin, Yuandong Pei, Zhixing Zhao, Jiangshan Shi, Zhengyun Fan

Spraying medium to achieve an energy-saving and emission reduction for iron ore sintering has been researched, such as spraying natural gas, coke oven gas, oxygen, sintering flue gas and gas from annular cooler. This paper focuses on effect of spraying steam on sintering surface on reduction of NOx and dioxin emissions in practical sintering production in Shougang Jingtang. It can be found that, with the increase of sintering bed spraying steam amount, NOx and dioxin of flue gas showed a decreasing trend. As spraying steam 1 t/h for 550 m2 sintering machine in Jingtang, NOx content decreases 2.6–9.5 mg/Nm3, and dioxin decreases 0.007–0.014 TEG ng/Nm3.

Mar 1, 2018

By Frank B. Fulkerson

Mining began in Pend Oreille and Stevens Counties about 1885, Lead and zinc have been the principal products, and the area has supplied nearly all the output of these metals in the State. Fend Oreille County's output of lead and zinc from 1902 to 1956 was 110,700 and 229,600 tons, respectively. The Stevens County total was 54,100 tons of lead and 87,600 tons of zinc. Copper ore was produced mainly from the United Copper mine, Chewelah district, from 1912 to 1920; the principal gold mine was the First Thought, Orient district, which was active from 1904 to 1942. Approximately 225 mines and prospects produced; most of the ventures were on a small scale. The total value of gold, silver, copper, lead, and zinc produced from 1902 to 1956 was $75.2 million in Pend Oreille County and $39.4 million in Stevens County. INTRODUCTION In compiling the figures for this report, use was made of Bureau of Mines permanent records of nine production, the annual tabulations of producing mines, and the Minerals Yearbook. Requests to publish individual data, obtained from the annual production canvass, were made to the latest recorded operators of all mines in the area. Response to this request was good; therefore, it was possible to make the tables nearly complete. In a few instances the producer requested that the production data remain confidential, and in others it was not possible to reach the mine operator at his last known address. The district and county tables combine statistics for all mines, including those mines whose output could not be published separately.

Jan 1, 1958

By A. Habibi

The FMC Westvaco Trona Mine is located near Green River, Wyoming and has an annual production of 4.5M tons. Trona is an evaporite mineral that is processed into several products, mostly soda ash. The underground mine has two active development panels and one longwall (LW) panel. The mining horizon is about 500m below surface and the surrounding strata liberates methane. Three surface-based, blowing fans provide ventilation air as a positive pressure system. The mine operates a 225m long LW face, built by Joy Mining Machinery. Headgate and Tailgate developments are driven with four entries. The recovery room, at the end of each panel, is 8m wide with three access chutes. Additional recovery room support comes for concrete blocks used with a center to center spacing of 1.5m. As the LW enters this pre-driven recovery room there are notable responses and shifting ground stresses. This study was undertaken to measure the ground response using seven vibrating wire displacement transducers. These devices were used to monitor the convergence as the LW approached the recovery room. The methane concentration in the air ventilating the recovery room was also monitored. The correlation between convergence and gas liberation was then studied. The results show that the convergence varies from 0.1m to 0.25m along the length of the recovery room. Ventilating the recovery room becomes critical as methane is liberated from oil shale as the more plastic floor material is disrupted. Appropriate methods are employed to ventilate the recovery room.

Feb 23, 2014

By Michael Day, Paul Kos, Scott Brinton

A hydrogeologic characterization and impact analysis was performed for a proposed quarry at the Hitch Rack Ranch located in the Little Turkey Creek watershed southwest of Colorado Springs, Colorado. Continuous multiple channel tubing, nested piezometers, stream flow measurements, and mapping of known seeps were used to define the three-dimensional potentiometric distribution and areas of groundwater recharge and discharge. Water balance considerations, mass balance calculations, and potentiometric response to earth tides and barometric fluctuations confirmed that the granite fracture system in the ridge area of the proposed quarry has an extremely low bulk hydraulic conductivity resulting in minimal groundwater discharge to sustain the baseflow of Little Turkey Creek. The Little Turkey Creek valley forms the major conduit for groundwater flow exiting from the upper part of watershed underlain by granite. This conclusion has significant implications with respect to mine planning to minimize projected impacts to the hydrologic system and preserve this recharge component to downgradient Denver Basin sedimentary deposits.

By Stephen E. Kesler

Carbonaceous sedimentary rocks are abundant in the upper part of the caldera or maar that hosts the Puebio Viejo Au-Ag district, and much of the Moore sulfide zone is in these rocks. These rocks are thinly layered and contain scattered plant remains and variable amounts of volcaniclastic debris and pyrite. The carbonaceous matter in the sediments yields no X-ray diffraction pattern and is not graphite. It has C/N ratios of 4 to 10, and &13C values of about -25 per mil, which indicate that it is dominantly of marine organic origin and partly degraded. Atomic S/C ratios in the unmineralized part of the carbonaceous rocks have a median of about 1.2, much higher than most similar unmineralized rocks, reflecting not only the abundance of pyrite in the sediments, but also the fact that the organic material contains several percent sulfur. Extracts from the organic material indicate that it is thermally mature and that it reacted with the hydrothermal solutions. Atomic S/C ratios in the mineralized carbonaceous rocks are generally higher than those in unmineralized carbonaceous rocks, ranging to values of 5 and more. These differences indicate that significant amounts of carbon were consumed by the reduction of sulfate and metal chloride complexes in the mineralizing fluids as they passed through the carbonaceous sediments. Direct reaction between organic material and ferrous chloride-bearing, acid-sulfate hydrothermal solutions probably caused continuous deposition of pyrite during this period. Intermittent deposition of gold from chloride complexes by the same reaction was probably facilitated by boiling or C02 effervescence.

Jan 1, 2013

By A. Eitzenberger

This paper describes a study of seismic records from the Kiirunavaara mine footwall which were interpreted in relation with numerical models developed outside the study. Seismic data was retrieved from a portion of the mine and filtered with respect to the ratio between energy carried by an event's P (primary) and S (secondary) waves (Es/Ep ratio), local magnitude, and active mining depth. The data was analysed using Es/Ep ratios and Gutenberg-Richter graphs to determine the event origin, mechanisms, and minimum magnitude cut-off. The magnitude completeness was identified by studying the b-value stability and b-value differentiation between origin sets. It was shown that, by separating seismic events into the origin components shear, complex, and tensile based on Es/Ep ratios, a representative value for the magnitude completeness can be identified for a catalogue with a convex cumulative log curve. The majority of the events were shown to be of shear-slip origin based on the recorded Es/Ep ratios, with pure tensile events constituting only about 10% of the recorded data. Spatial and temporal event location patterns were studied and compared with numerical modelling results. The comparison showed a correlation between shear-slip seismic events and volumes experiencing high differential stresses in the lower part of the footwall. In the upper part of the footwall the results did not reveal any clear correlation between observed damage in drifts and seismic event locations. The concentration of seismic events in the lower portion of the footwall is discussed in the context of rock mass displacements. The results indicate a possible connection between mine seismicity at depth and damage observations in the drifts in higher non-seismic areas by seismic softening and subsequent lateral expansion of the rock mass.

Jan 1, 2017

It is a commonplace of our industry that prices of most minerals have been historically weak during the 1980s. The International Monetary Fund's index of prices of metals fell 25 per cent between 1980 and 1982, rose slightly in 1983, and has since fallen further. In December last year it was 37 per cent below its 1980 average. The few temporary exceptions to the mineral industry's malaise highlight the excess capacity, which largely explains the weakness of prices. The industry has painfully come to recognise that more satisfactory prices will not be restored until supply capability and demand move back into better balance. Mine capacity was installed in the expectation of much faster growth of demand than has occurred. For a variety of reasons mine and plant closures have been insufficient to restore equilibrium to the market-place. The industry may, therefore, have to resign itself to continued weak prices for some years more, at least by the yardstick of the 1970s. Growth rates of demand have slackened off in line with economic activity, and in response to continuing substitution and technological improvements. To the extent that the recent weakness of oil prices stimulates the industrial countries' activity, demand for non-fuel minerals may grow faster than most forecasters now predict. It is, however, much too early to say how long the weaker oil prices will persist, and even more difficult to estimate their probable effects. In typical post-war business cycles the usual response to recession was to batten down the hatches, and ride out the storm. Sooner or later, and probably sooner, demand resumed its previous trend path, and prices recovered. The market, in effect, bailed mines out of trouble; the more efficient could make attractive pre-tax profits whilst even the poor to mediocre could earn a satisfactory living. Prices rose at least as fast as general inflation, and in the early 1970s much faster. In retrospect those price rises of the early 1970s were historically abnormal but they did not appear so in the prevailing inflationary climate of the time. When the market failed in the early 1980s many of the hardest hit companies looked for scapegoats.

Jan 1, 1986

By W. H. Pomroy

This report describes research by the U.S. Bureau of Mines to design and in-mine test a rapid response pneumatic fire detection system for multilevel metal mines. The relative merits of pneumatic detection are discussed in the context of typical multilevel mine layouts and environments. The Bureau's prototype system is described, with emphasis on design features that counter commonly experienced and/or perceived operating problems with pneumatic detection systems. Finally, the results of a 3-year in-mine performance evaluation of the prototype system are discussed.

Jan 1, 1990

By Xia Lou, Hossein Dashti

Gas hydrates technology has been considered as an alternative method for carbon dioxide (CO2) separation. A wide range of studies have been reported in the past decade on the improvement of the separation efficiency by using chemical additives. While most of these studies have shown improved kinetics, thermodynamics and/or separation efficiency at the laboratory scale, there has been no quantitative analysis of the energy consumption for viable industrial applications. Comparison of the effectiveness of the chemical additives from separate studies or groups also is impossible. The present work is focused on the modelling of the hydrate-based CO2 separation process and provides a quantitative approach that is new in its analysis of the effectiveness of chemical additives in relation to the energy required and the kinetic parameters involved in the process.

Mar 1, 2018

By R. V. Higgins

Many contributions to methods of forecasting the performance of waterfloods of a five-spot pattern have been made by investigators. In most of these forecasting methods, a previously selected sweep efficiency is used, and other simplifying assumptions are employed to obtain the objective. In this paper the calculated oil recoveries from several five-spot single- and multiple-layer stratified reservoirs were made with a minimum of assumptions, and because of the techniques used, no previously selected sweep efficiency was required. As a result, the accuracy of the forecast is increased. Permeability curves and continuously changing saturation gradients are used in every section of the pattern. By means of a potentiometric model, the flood pattern is divided into channels, the centers of which are the streamlines. The channels are divided into cells. As flood water enters, the permeability and saturation of each cell change with time. In this study the production from multiple-sand layers of different absolute permeability but with the same relative permeability-saturation relations are combined. The results are shown for a single- and 10-layer reservoir with a permeability variation of 0.60. The oil rate, water-oil ratio, and recovery are shown as functions of time for a 2- and 20-centipoise oil starting in primary phase and after fill-up.

Jan 1, 1962

What is your assessment of the current state of the minerals industry? It is no understatement that domestic mining is facing a severe crisis at this time. The sharp decline in commodity prices and demand is putting a great strain on domestic and worldwide mining, causing major declines in profits and market capital of mining companies. This, in turn, has lead to major production cuts, layoffs, shut-downs of operating properties, and the deferral of new and expansion projects. These changes in the minerals industry have played a major role in the health of the economy. Operationally, the industry continues to develop new technologies that are making our work more efficient, more cost effective and more environmentally acceptable and safe. During downturns like this, companies generally pay closer attention to operational efficiencies and process optimization. Historically, new technologies and processes tend to be developed during down markets, and I believe we will see the same thing as companies strive to preserve liquidity and maintain or improve their margins. On the positive side, the drop in commodity prices has resulted in a reduction in operational costs, as the costs for fuel supplies and construction materials have decreased.

Jan 1, 2009

A party of some 60 members of the Institute were welcomed at the Union Junction Works of Scaw Metals Limited on Thursday, 23rd January for a morning visit. Dr J. M. Bereza, the metallurgical Director, gave an informative introductory talk to the assembled visitors, which briefly covered the major activities of the Company. This was followed by refreshments, and the visitors were then allocated to 12 guides for the conducted tour of the Works. The progress of the Company is an impressive saga of the development of heavy industry in this country linked primarily to the expanding mining industry. Many other outlets are now available for Scaw products and the rapidly advancing techniques developed by their own chemists as well as the processes made available from overseas associates indicates the forward looking attitude of the Company. The visitors were impressed by the modern laboratory services, closely linked to rigid quality control, resulting in a high standard of final products. The most fascinating section to many of the visitors was the continuous casting machines and rolling mills recently installed, although the most lucrative section is the large steel foundry. After the tour the parties gathered in a marquee tent for liquid refreshments, followed by a lavish luncheon in the canteen. The visitors were officially welcomed by Mr Richard Boustred, the Deputy Managing Director, and Mr V. C. Robinson replied, thanking the Company on behalf of the South African Institute of Mining and Metallurgy. Arrangements were made for golf in the afternoon at the Germiston Golf Club for those who wished to play. A.E.G.