Search Documents

By W. T. Ober

the hammering effect acts only to a point 3 in. back from the cutting edge, and the hardening heat extends back only 1 in. from the cutting edge. Then, as a steel is taken from the fire, the grain condition is as shown in Fig. I. After the forging operation has been performed the condition shown by Fig. 2 exists. The heating operation to harden the cutting edge produces the effect shown in Fig. 3. The questions that naturally arise are: Will the cost of the extra heat treatment necessary to change this condition (annealing) be more than the saving that may be effected in the drill steel or will the extra heating be an economical as well as a wise thing to do? Is this condition necessarily detrimental to the maximum service of the drill steel? Can this annealing action be obtained in the hardening heat by heating more of the bit, say at least 5 in., to the hardening temperature but quenching only the end of the bit by a shallow immersion? Short Rock-drill Steels Reclaimed by Welding By W. T. Ober, Lynn, Mass. Experimental tests by the Thompson Company have shown that short lengths of rock-drill steels may be reclaimed by electric butt welding. The drills used in the experiments were hollow drills l1/4-in. in diametcr containing 0.95 per cent. to 1.05 per cent. carbon. The ends to be joined must first be ground off fairly square and the greater part of the rust, scale, etc. removed for 3 or 4 in. back in order to insure good electrical contact with the dies of the welder and countersunk, with an 80° countersink, approximately 1/4 in. The steels are then clamped in the copper dies of the welder, so that a length projects from the inside edge of each pair of dies equivalent to from one-half to three-quarters the diameter of the drill. The drills should also be brought into accurate alignment. The first step is to bring the ends into close proximity and then close the primary circuit of the transformer, slowly bringing the steels together until their ends lightly touch, when they will "flash," that is, minute

Jan 1, 1922

By Gamal Rashed, Tim Miller, Nicole Evanek

High horizontal stress has been identified as a critical factor affecting roof stability in underground mines, particularly when the immediate roof consists of weak or laminated rock. Numerical models were employed to better understand the influence of caprock thickness, cutting sequences, and the orientation of driving direction relative to maximum horizontal stress on roof stability in underground stone mines. These models were calibrated based on field observations of roof falls from the study mine. The findings of this study enhance our understanding of roof stability under high horizontal stress and contribute to reducing the risk of roof falls in underground stone mines.

Feb 1, 2025

By M. J. Marcinkowski, K. S. Raghavan, A. S. Sastri

A detailed transmission electron microscopy investigation was carried out in connection with a manganese Hadfield Steel. At small plastic strains, numerous individual intrinsic stacking faults are observed. With increased plastic deformation, the stacking faults thicken into twin lamellae which in turn subdivide the original austenite matrix into smaller domains. The twin boundaries act as strong barriers to subsequent dislocation motion and is in a sense equivalent to grain refinement. It is this "grain refinement" which is believed to be the cause of the very high work hardening rates in the Hadfield Steels. In many cases, especially where an hcp phase is the stable one at low temperatures, the stacking fault energy in fcc metals and alloys decreases with decreasing temperature.' Since stacking faults of the intrinsic type are precursors of both twins as well as the hexagonal close packed structure, both of these entities should become more frequent as the temperature of a fcc crystal is lowered. In the case of the twin, there is no chemical driving force for its formation and it is generally necessary to provide the required driving force by an applied stress, i.e., strain energy. In the case of the hcp structure the transformation from the fcc modification can occur spontaneously (marten-sitically) since a decrease in chemical energy does in fact occur; however, an applied stress will provide an even greater driving force toward complete transformation. Since the transformation products mentioned above occur in an inhomogeneous manner throughout the crystal and since these can act as potential barriers to further plastic deformation2 marked strengthening effects can be anticipated. Also because metal and alloy strenghening is in general proportional to the shear modulus, these effects should be greatest in steels of the austenitic type (y), i.e., the fcc types. Perhaps the two most important steels in this category are the austenitic stainless steels and the Hadfield manganese steels. Both may be quenched from elevated temperatures so as to retain the austenitic states characteristic of those temperatures. The effect of subsequent deformation at lower tem- peratures has a profound effect on the stress-strain curves of these alloys. In particular Fig. 1 shows the compressive stress-strain curves obtained with an 18-8 stainless steel which was quenched from 1850°C after annealing for 1 hr so as to produce all y. As the temperature is lowered, the work hardening rate increases markedly. Although some hcp or c mar-tensite can be generated by plastic deformation as the temperature is lowered,~ it is believed to be a transition phase4 and most of the martensite produced is of the bcc or a variety.3 It is this stress induced martensite which gives rise to the very low initial work hardening at 77°K as can be seen in the stress-strain curve in Fig. 1. Similar low initial work hardening rates have been observed in the stress induced Ni-Ti martensites.5 Fig. 2 shows that an even more rapid rate of work hardening occurs in the Hadfield steels treated in the same way as that described for the 18-8 stainless steels a; the temperature is lowered. It is this ability to work harden to such high stress levels that makes the Hadfield steels particularly suitable for armor plate and heavy construction equipment. However, unlike the case of Fig. 1, no initial low rate of work hardening is observed in any of the curves in Fig. 2. Thus the stress induced formation of any low energy martensite phase in any significant quantity must be ruled out. This observation is in accord with the X-ray findings of Otte.~ On the other hand, small quantities of the E phase have been observed by other investigators using transmission electron microscopy (TEM) above Even more significant was the fact that large numbers of deformation twins were observed in the deformed Hadfield steels,678 which were postulated to be one of the reasons for the high work hardening ability of this class of steels.8 It is the purpose in what follows to discuss a series of experimental observations pertaining to the stress induced transformation in a Hadfield steel and to formulate a dislocation mechanism which adequately accounts for the observed results. EXPERIMENTAL PROCEDURE The stainless steel used to obtain the curves shown in Fig. 1 was of the AISI Type 303 containing approximately 18.0 pct Cr and 8 pct Ni. On the other hand, the Hadfield manganese steel used to obtain the curves shown in Fig. 2 contained between 1.00 to 1.25 pct and 11.5 to 13.5 pct Mn. In all cases the samples were in the form of compression cylinders 0.220 in. in diam and 0.370 in. long. Prior to testing the samples were annealed for a hr at 1050°C and rapidly quenched into a brine solution. This treatment was sufficient to preserve the y phase for subsequent testing at lower temperatures. All samples were compressed in an Instron testing machine using a cross head speed of 0.02 in.

Jan 1, 1970

By Russell R. McLellan

As part of an effort to develop new or improved placer mining technology in the Tertiary gold-bearing channel gravel of northern California, the Bureau of Mines conducted investigations at the old Badger Hill placer mine in Nevada County, Calif., to collect data and information regarding drilling and sampling methods and deposit characteristics. Sampling studies involved the collection and processing of 400 tons of large-and small-volume samples from drill holes, underground workings, surface pits, and blasthole rounds. A total of 355 samples averaging 2,296 pounds per sample provided reasonably accurate data for analysis of the gold distribution. These studies indicated that the bulk of the gold is within 40 feet of bedrock in stacked, lenticular zones of cemented gravel that are largely confined to the relatively narrow, meandering course of the deepest portion of the bedrock channel. Drilling studies involved the testing of truck-mounted rotary, buckett and vibratory drills, none of which proved to be a completely versatile tool for sampling quickly and reliably both consolidated and unconsolidated gravel..

Jan 1, 1974

By O. M. Popoola, A. P. I. Popoola, D. O. Okanigbe, A. A. Adeleke

The physical, chemical, mineralogical and morphological characteristic of the waste copper smelter dust (CSD) from Palabora Copper (PTY), Limpopo, South Africa, has been reported in the open literature. The bulk of this material falls within the −53 μm particle size fraction with a copper weight percent of 18.02 as determined with the XRF. The high presence of reactive gangue minerals such as mullite (42.97 wt%) and quartz (11.45 wt%) necessitates that the waste CSD be first upgraded of its copper value in the falcon gravity concentrator before subsequent hydrometallurgical treatment. As an initial step, a sample preparation was carried out to make the sample amenable to both real density determination and copper upgrade experiment, thus resulting in 97% of the particles passing the 300 μm sieve aperture (d97 = 300). The laser particle size analyzer (LPSA) was used to analyze the d97 = 300 and the results showed a %change from 90.82% to 95.59%, with a real density of 2.830 for the waste CSD. The result of the copper upgrade showed that test 8 with treatment combination of 80 rpm and 4.5 l/min gave the highest % copper grade of 1.37 which is still less than the %grade of copper in the feed (1.49%). It thus lead to the recommendation that another type of centrifugal separator that will allow the introduction of the feed as slurry so that the pulp density and feed rate can factored into the whole upgrade experiment, consequently reducing the significant amount of losses and the chances of an improved grade and recovery of copper from this waste CSD.

Mar 1, 2018

By Aruna Mangalpady, Sandeep Kumar Jeripotula, Govinda Raj Mandela

Injuries due to work-related musculoskeletal disorders (WMSDs) are not uncommon in heavy industry like mining. Researchers acknowledged that occupational exposure to ergonomic risk factors is the chief causative factor in the development ofWMSDs. The aim of this study was to perform an ergonomic assessment of musculoskeletal disorders among surface mine workers in India. Standardized Nordic Questionnaire was used to collect subjective response from 500 workers. A stratified random sampling method according to surface mining work activity type was used to obtain the sample. Data was collected by means of a structured questionnaire, and the Statistical Package for Social Sciences (SPSS) was used to analyze data using descriptive and inferential statistical methods. A response rate of 85% was obtained out of 500 targeted groups. TheWMSDs prevalence for the 12-month period was estimated to be 44.23%. The mean and standard deviation of workers’ age were 41.31and 8.927, respectively. The study has shown that the operators of dumpers, dozers, and graders along with electricians were found to be the most susceptible to developWMSD problems. Among the most affected body parts, back disorder reported the highest. Further, it was found that working with static posture over the longer duration has a significant association with the lower back disorder (with p = 0.020) and bouncing and jarring has also significantly associated with the lower back disorder (with p = 0.023). Similarly, a significant association was found between repetitive work and neck pain (with p = 0.016). The study depicted a significant association between ergonomic hazards and WMSDs, like working with prolonged static posture, bouncing and jarring, and repetitive work.

Mar 13, 2020

By Barnabas Bryan

In the year 1875, the Pennsylvania Supreme Court, acting on incorrect information concerning the production of oil and gas, established what has become the law of the land for the governing of oil production. While the decision was ideal for the refining monopoly which was completed in that year, there is no evidence that the court was in any way influenced by that refining monopoly. The evidence indicates that the court accepted the view of the royalty owner and independent oil producer. Throughout the life of the refining monopoly it accepted this law, which was so evidently to its advantage in securing cheap raw material. The same policy continued until the development of the exhaustion theory and the entry of the various units of the former monopoly into the production of crude oil. It is curious that no one doubted the new theory of shortage sufficiently to feel the need of changing the law. When the theory entered the economic field sufficiently to raise crude oil prices beyond justification it shortly disproved itself, but by this time the question of split ownership in producing fields made a change from legal error to justice too complicated to be undertaken by the large companies. Not even the ardent advocate of unit operation dared to carry the question to the United States Supreme Court, which has never been asked to pass on the complete question. The impossible position of the producing industry, hemmed in on one side by court law compelling wasteful production and on the other by the national law against cooperation, lasted until the demoralization of 1927 led to cooperation within a state and under state guidance. Since that time control of production has grown with the bringing in of each new field and at this time has the active support of the Department of the Interior in such ways as are definitely legal. As in 1875, the royalty owner and independent producer are opposing by all possible means the rational conduct of the business of producing crude oil. Fluctuation in Investments The investor in oil securities has not been as badly fooled as has the oil man himself. Fig. 1 is designed to show the composite regard of all

Jan 1, 1930

By Charles Catlett

Having had charge during the past year of the operations of the New River Coke Company, the second largest, if not the largest, coke-producer in this district, my attention was called particularly to the yield of coke from the coal as coked in a bank of beehive ovens, as the record showed that this yield, while believed to be well up with the practice of the district, was much lower than the analysis of the coal indicated it should be. The coal is well known to many members of the Institute, and the scope of this paper does not include a discussion of its occurrence and development. It suffices to say that the New River district comprises the mines working on the coals of No. XII. or the Conglomerate Series of the Rogers brothers, which are located on New river and its tributaries, and which find an outlet for their product east and west over the Chesapeake and Ohio Railway. The New river through this section carries the drainage from an extensive peneplain in which it has formed a very striking and stupendous canon, probably the most striking east of the Mississippi river. The only practical access to this territory is by means of this canon and the Chesapeake and Ohio road, and the opportunities for development by other lines may be considered as nil. If it were not for the fact that this road, farther west, reaches and develops entirely different coals, which are found in other measures, the New River district might properly be spoken of (as is now done at times) as the " C and 0. field." For fuller information on the geology of the region, those interested are referred to the ery complete monograph on the subject by Mendenhall and Campbell of the United States Geological Survey. The rocks are the same as those which carry the more widely

Jan 1, 1900

By A. Aaltonen, S. Paloranta, H. Myllykangas

A property based dynamic model of flotation was built and validated for training purposes. The model is based on the work of the AMIRA P9 project. The recovery of each particle with composition and size is calculated in a given simulation step. The model takes into account machine and operational parameters such as air flowrate and froth height. The model was created using fullscale test data on Pyhlisalmi Cu-Zn-pyrite ore with flotation kinetics of multiphase particles determined. Simulation and validation shows that model can predict the dynamic behavior of the process accurately enough for training purposes.

Jan 1, 2009

By C. A. Herbert

Coal-mine explosions in the United States during the past 10 years ranked third among the causes of coal-mine fatalities and constituted 16.1 percent of the total fatalities. In Indiana, however, during this same period the percentage of fatalities from this cause was much higher than the average percentage for the entire country. It is only through knowledge of the factors that have led to these past explosions that intelligent steps may be taken to prevent similar occurrences in the future. Although information concerning many of the earlier explosions is lacking, an attempt has been made to tabulate the information available in the hope that it may be of assistance in calling attention to some of the principal causes of explosions in Indiana.

Jan 1, 1934

By Ayman Tawadrous

Cave mining offers a flexible technique to exploit large, low grade, deep ore bodies with low operating costs. It is typically done in either a top down approach; i.e. sublevel caving, or in a bottom up approach; i.e. block or panel caving, to extract ore bodies that may have been previously considered unfeasible to mine. Sublevel Cave (SLC) mining, in particular, is a cave mining method based upon the utilization of gravity of blasted ore while the overlying host rock fractures and caves under induced stresses and gravity. Thereby the caved waste originating from the overlying rock mass fills the temporary void created by ore extraction to achieve a controlled collapse of the roof.

Jan 1, 2015

By W. C. McBee

A family of modified-sulfur cements has been developed by the Bureau of Mines for the preparation of construction materials with improved properties. Various types of sulfur cements were prepared by reacting sulfur with mixtures of dicyclopentadiene (DCPD) and oligomers of cyclopentadiene (CPD). Durable cements were prepared with structural characteristics ranging from rigid to flexible. These cements were used to prepare corrosion-resistant materials for use in a wide variety of industrial applications where resistance to acidic and salt conditions is needed. These materials were prepared as rigid concretes, flexible pavings, spray coatings, and grouts. Production of modified-sulfur cements in a commercial-size plant was demonstrated.

Jan 1, 1981

By Alpagut Kara

Turkey is the fifth biggest ceramic tile exporter in the world. Considering the expectation that the Turkish tile sector continues to expand, further studies both on the improvement and the development of tile formulations are necessary in order to make the producers advantaged in the world market while maintaining the capital and running costs at reasonably competitive levels as well. In addition to such studies, waste management in tile manufacturing has also recently become an important issue. Accordingly, the industrial use of wastes in the traditional ceramic industry has been intensively investigated in the recent years. This work describes part of a detailed research project carried out jointly on the possible re-use of muds (raw production waste) from glazing and pressing lines of a local tile company in the development of new wall and floor tile formulations. In order to achieve this, the waste material was firstly investigated in function of chemical and mineralogical compositions. Then, the particular focus was given to the presence of the waste material in increasing amounts on the thermal behaviour and physico-mechanical properties of the re-formulated tile bodies. During the studies, SEM in combination with EDS, and thermal analysis techniques such as non-contact dilatometry were widely employed. The results indicated that it was possible to use the waste materials in the commercial tile production without deteriorating the relevant technological properties.

Jan 1, 2006

By D. Gove

All mining operations using trucks have a common need to properly match the number and size of hauling units (trucks. wagons. scrapers. etc.) to a loading unit (wheel loader. hydraulic shovel/excavator, cable shovel. push tractor. etc.) to provide the best possible fleet match. Optimizing fleet match minimizes the cost per unit of material moved by that fleet. As haul conditions change (haul length. grade. or rolling resistance), there may be need to adjust the number of trucks to maintain the optimum fleet match. Fleet Production and Cost is a tool which, among other things, can be used to optimize the truck-loader match.

Jan 1, 1994

By E. G. Leonardon, C. Schlumberger, M. Schlumberger

Last year the authors presented a paper that discussed the various electrical measurements they perform in drill holes, which they name "electrical coring."' The object of the present paper is to give a brief account of the points of scientific interest that have been elucidated by further field work and laboratory research, as well as the economic results that have been attained recently. The practical examples given in this paper are drawn, for the most part, from the field work performed in Russian oil fields during the years 1931 and 1932. This is due to the fact that, thanks to the comprehensive cooperation of the Russian geologists and scientists, the authors are allowed to make public a large amount of recant information. In other countries in which the authors are engaged in similar work, the competition between private companies makes it imperative, for a considerable lapse of time, to avoid publication of the results obtained. The following points will be discussed successively, under separate headings: 1. Electrochemical phenomena in drill holes. 2. Stratigraphic correlations and tectonic studies. 3. Relations' between the productivity of oil horizons and their electrical resistivity. 4. Location of coal seams. 5. Summary and conclusions. Electrochemical Phenomena in Drill Holes Technical Publication 462l described the author's discovery concerning the existence of important differences of potential spontaneously gener-

Jan 1, 1934

By Edgar A. Scholz, Attilio G. Spat

The rapid worldwide increase in labor costs, prices of goods and services, and the rising tide of economic nationalism do not bode well for the future of mineral exploration and the mining industry. The increasing complexity and difficulty involved in finding economic mineral deposits makes these trends particularly significant. A comparative cost analysis of domestic and foreign exploration projects which developed into mines during the period 1960-74 may be useful in indicating the general nature of exploration expenditures as these trends continue. This analysis is based on a survey of 18 US and Canadian mining companies. Due to the inexact nature of exploration expenditure data, plus the fact that no two mining companies follow the same system of cost allocation, the results of the survey must be considered quite general in character.

Jan 6, 1977

By John C. Morrisey, Harold M. Ray

With full production from the Casteel Mine in 1987 The Doe Run Company, a wholly owned subsidiary of the Fluor Corporation, encountered a significant increase of copper and iron to the Viburnum Mill. This major change of the lead, zinc, and copper metal ratios in the ore created circuit problems which adversely affected concentrate quality. Recognizing the problem, the company embarked on a metallurgical research program to include laboratory, pilot plant, and plant testing. The program developed an innovative copper prefloat process which both increased copper recovery and significantly improved concentrate quality. The process was tested and first operated at Doe Run's Brushy Creek Mill then installed at the Viburnum Mill in 1992. A brief history of development, plant operating data, and other potential applications for the patented processes will be described in the paper.

Jan 1, 1993

By V. Lessels, D. J. Buckwalter, D. H. Rose

At White Pine Copper Co.'s operation in the Upper Peninsula of Michigan, the company has been losing more than four lbs of copper in each ton of sand tailings. With an average rate of 12,000 tpd of sand going to the tailing pond daily, the company has been losing more than 14 million lbs of the red metal annually. With an eye aimed toward lessening this loss, White Pine engineers in 1959 initiated a study on techniques for recovering this "lost" copper from the sands. Inasmuch as the flotation operation was considered to be optimized, a logical approach seemed to be leaching. For various reasons ammonia, ferric chloride, acid, and biological leaching were ruled out as impracticable. This led to a consideration of cyanide leaching as practiced in the precious metals industry.

Jan 8, 1967

By M J. Pejovic, I Miljanovic, A Milutinovic4, T Benovic, A Petrovski

The paper presents a model of a multigrade monitoring-management structure for support to decision making and management in real and extended time in mineral processing (MP). The model was created as a result of a long-lasting research, design and development of mining, computer integrated monitoring-management systems. Apart from the general explanations, the authorsÆ state in the introduction that efficiency of a system for support to decision-making and management in mineral processing is more difficult to achieve by conventional approaches, than by the fuzzy logic approach. Starting from the multiphase structure of process flows in MP, the following are process and monitoring-management oriented graphs. The graphs served as a foundation of the multigrade hierarchical fuzzy model for support to decision making and management in MP. Following the example of the monitoring-management system of the æRudnikÆ mine flotation plant, fuzzy logic implementation was shown. The key conclusions of the paper are that fuzzyfication of layers of the decision making and management model has full justification due to the complexity and dynamics of mineral processing processes, complications and often insurmountable difficulties concerning the precise description of real systems by conventional mathematical tools, variability of external influences, and the (general) non-linearity of the MP processes management criteria functions.

Sep 26, 2011

By Selvin Yesilay, Guray Kaya, Bekir Karasu, Asli Cakir

"In this investigation, the wastes of Eti Maden Kirka Boron Company of Turkiye were evaluated in the production of diopside and anorthite-based glass-ceramic glazes suitable for porcelain tiles fast and single-fired under industrial conditions. First of all, high wear resistant frits were produced with the use of concentrator and derivative borax wastes. Second of all, pre-engobed porcelain tile bodies were coated with the standard and newly produced frit-based glazes and industrial fast single-firing was employed. Final products were undergone to the certain standard tests to determine their Vickers hardness, wear resistance, thermal expansion coefficient values, gloss and coloring parameters. The micro-structures and phase formations of the fired glazes were also studied. Consequently, it was confirmed that the utilization of borax solid wastes in fast single-fired porcelain tile glass-ceramic glazes is possible. Introduction Porcelain tiles were introduced at the end of 1980s by Friandre, one of the leading Italian porcelain manufacturers. The American National Standard Specifications for Ceramic Tile defines porcelain tiles as: dense, smooth, impervious (with water absorption value less than 0.5 %) and stain resistant [1]. The excellent technical performances for ceramic tiles, such as mechanical, wear, frost and chemical resistance that make their use possible in indoor and outdoor building applications [2-3]. In the last decade, the growth rate of the global production of porcelain tiles increased more than those of other ceramic products; in fact, the technical properties of porcelain tile, coupled with even more improved aesthetic appearance, gave it a prominent role on the tile market [2]. Glass-ceramics are composed materials of one or more crystalline phases immersed in a residual glassy phase [4-5]. Glass-ceramic technology is based on controlled nucleation and crystallization of bulk glass [6]. The concepts of controlled crystallization of glass designate the separation of a crystalline phase from the parent glass in the form of tiny crystals. Their growth rate and final size are controlled by a suitable heat treatment [7]."

Jan 1, 2008