Search Documents

About twelve months ago, owing to the increasing quantity of stone and dirt being drawn frQm the Victorian State Coal Mine due to the large amount of dead work below ground, cutting, faults, etc, and to the increasing quan#ty of banded coal beingworked, the writer was forced to consider the question of economy in handling the spoil at the surface. The method in operation at the time was to run out level dumps fro,m the, tipping floor of the heapstead, or brace, and to tip most of the skips of stone in tipplers at the ends of the dumps, the remainder of the skips being side-tipped to widen the dumps.The method, whilst quite satisfactory for dealing with a few skips of stone, was found to be costly as the dumps extended, and the number of skips to be dealt with increased from 300. to 400 per day of two shifts;. therefore, in order to expedite thework and cheapen its cost, the writer devised an improved method which may be qescribed as follows :-(1) The stone is tipped into a hopper car which holds about 10 skips(2) The hopper car is hauled up an inclined dump by means of an electric winch.(3) The spoil is dumped from the car forwards or to either side, as required.(4) The car is returned to the starting point for a further load.Plate I Fig. 1 gives an idea of the construction of the hopper car. In the illustration the car is in position for tipping to one side. The body of the car is supported on a ball race on the under carriage, and it can be swung round to tip in any required direction. The bottom of the hopper is extended to form a 4 ft. lip...

Jan 1, 1918

The upper amphibolite-grade mctasediments of thc rinaroo area, North Queensland, form part of a regional aurcole to the large Tinaroo Batholith and are the stratigraphic equivalents of the Hodgkinson Formation of gencrally low metamorphic grade. There is no evidence of any lithological unconformity.The higher grade metasediments have a more complex deformation history than is typical for thc surrounding region and this may bc due to one or a combination of two factors; an additional strain componcnt associated wilh the intrusion of Ihe Tinaroo Batholith, or a more marked finite strain response to the overall regional stress field within hotter. more ductile rocks.Four deformational events can be characterized within Ihc Tinaroo Area. Close to Ihe Tinaroo Batholith D1 and D2, arc so strongly developed that they disrupl the continuily of Ihe original Iithological layering. In the aureole region, D1 is strongly overprinted and its original fabric intensity is obscured, but both D2 and D3 display a mappable decrease in intensity away from the granite margin. These three deformations occurred during Carboniferous or early Permian time. D4 is later and only patchily developed.The broad, moderate pressure metamorphic aureole surrounding the Tinaroo Batholith is a typical of the CairnsCooktown group of Permo-Carboniferous granitoids. which usually develop narrow, lower pressure contact aureoles. Two periods of metamorphism are distinguishable. The first reached peak temperatures somewhat greater than 520°C, the second temperatures around 620-630° C immediately adjacent to the granite contact.Several cale-silicate lenses containing scattered scheelite mineralization occur within the area. Scheelite appears to have crystallized at the same time as the cale-silicate minerals, its appearance coinciding with the intrusion of the Tinaroo Batholith. Unlike many "skarn-type" scheelite deposits, the scheelite-bearing cale-silicates are Fe-poor, with no positive correlation between total Fe and W.

Jan 1, 1982

By Y. Faitakis

In the mining industry, maintenance is a key priority and a major expense. As mining equipment is large in scale, high in cost, and difficult to tow, it is key to maintain equipment on a timely basis. Breakdown in -40°C or away from a maintenance station can cause great costs in repair as well as lost production. It has often been quoted that about 5% of the North American production is lost every year due to unscheduled downtime. About one-third of the downtime is attributable to equipment failures. From this fact alone, it is evident that proper equipment maintenance can add tremendous value to the bottom line. As organizations and equipment become more sophisticated, maintenance expectations begin to evolve. This evolution can be traced through three generations: The first generation (1940?1950): A ?fix it when it broke? attitude prevailed during that time, mostly because the industry was not highly automated. The second generation (1950?1980): Automation and mechanization of the industry increased. The industry now was dependent on machines performing the majority of the work. Preventive maintenance (overhauls at fixed intervals) appeared as the first maintenance practice. Maintenance costs started to rise rapidly. The third generation (1980?): Assets become more complex. Failure modes are better understood and computerized maintenance methods are becoming mainstream. Condition-based maintenance (CBM) starts to gain ground as a cost-effective alternative, replacing the fixed interval overhauls. As corporations amalgamate and market places are becoming more complex, multi-functional teams become responsible for maintenance. At the beginning of the third generation, maintenance organizations began embracing technology to provide efficiencies in maintenance management. A strong push was made to transition from reactive maintenance to proactive maintenance. At the forefront of this push is condition-based maintenance.

Jan 1, 2004

By Y. Faitakis, G. J. Powley, C. Mackenzie

"In the mining industry, maintenance is a key priority and a major expense. As mining equipment is large in scale, high in cost, and difficult to tow, it is key to maintain equipment on a timely basis. Breakdown in -40°C or away from a maintenance station can cause great costs in repair as well as lost production.It has often been quoted that about 5% of the North American production is lost every year due to unscheduled downtime. About onethird of the downtime is attributable to equipment failures. From this fact alone, it is evident that proper equipment maintenance can add tremendous value to the bottom line. As organizations and equipment become more sophisticated, maintenance expectations begin to evolve. This evolution can be traced through three generations:The first generation (1940–1950): A “fix it when it broke” attitude prevailed during that time, mostly because the industry was not highly automated.The second generation (1950–1980): Automation and mechanization of the industry increased. The industry now was dependent on machines performing the majority of the work. Preventive maintenance (overhauls at fixed intervals) appeared as the first maintenance practice. Maintenance costs started to rise rapidly.The third generation (1980–): Assets become more complex. Failure modes are better understood and computerized maintenance methods are becoming mainstream. Condition-based maintenance (CBM) starts to gain ground as a cost-effective alternative, replacing the fixed interval overhauls. As corporations amalgamate and market places are becoming more complex multi-functional teams become responsible for maintenance.At the beginning of the third generation, maintenance organizations began embracing technology to provide efficiencies in maintenance management. A strong push was made to transition from reactive maintenance to proactive maintenance. At the forefront of this push is condition-based maintenance."

Jan 1, 2004

By Frik Badenhorst, René Roux, Peter Terbrugge

This paper presents a case study where economics dictated an aggressive slope angle and where an appropriate slope management programme allowed successful completion of mining to 190m below surface. The Navachab Gold Mine is located in Namibia and is one of the few gold mines in that country. Mining by open pit methods commenced in 1990 with economics dictating an aggressive slope design to minimise waste stripping and make the mine viable. With steep slope angles in the design, and a steeply dipping footwall geology, it was necessary to introduce a comprehensive slope management programme. This required good mining practice in limit blast techniques with pre-splits and trims, and good housekeeping to effect a safe and economical operation. The slope management programme in addition required in pit mapping and logging procedures, regular survey monitoring evolving to a robotic Geomos system, as well as slope instrumentation to monitor stability. Two relatively large scale failures occurred at the mine, the second of which impacted on the east wall access ramp, while the first was confined to an operating stack. The paper describes the design and slope management techniques developed for the east wall.

Jan 1, 2006

By D A. McCallum

With depth, many gold ores become sulfidic with minerals such as pyrite, pyrrhotite and arsenopyrite becoming prevalent. In addition, many underground gold mines use tailings backfill to bind and store the waste. In these cases, acid mine drainage (AMD) can become an issue. One approach to the control of AMD is desulfurisation whereby the sulfide minerals are removed prior to disposal. Four sulfide tailings samples, representing different ore types and gold and base metal operations, were selected for assessment and testing using simple physical beneficiation techniques. The aim was to determine the extent to which mineral processing methods were suitable for separating sulfides from non-sulfides and for extracting potentially marketable by-products from the tailings. In order to streamline the testing procedure a simple diagnostic separation technique was developed to enable quick screening of bulk sulfide tailings for suitability for reprocessing. The testing procedure involved detailed characterisation and a sequential set of testing regimes based on simple unit processes including water washing, classification, gravity concentration, magnetic separation and bulk flotation. The preliminary test results indicate each unit process can play an important part in producing effective sulfide/non-sulfide separations and in generating useful by-products from the tailings. Potential valuable products identified include coarse, benign silica sands, bulk iron sulfide products rich in pyrite and/or pyrrhotite, high-grade iron products (magnetite) low in silica, low-volume bulk sulfide concentrates and low-grade molybdenite and talc products. The work presented shows how sulfide tailings can be viewed as a resource rather than a waste stream, and identifies a pathway for developing a more sustainable approach to the environmental management of sulfide tailings for the future.

Jan 1, 2007

By Jim Rozek, Robert A. Gee

The Epping to Chatswood Rail Line project is the largest publicly funded infrastructure project in New South Wales. Construction commenced in November2002 with opening scheduled for 2008. The work includes 13 route km of twin TBM driven 7.2 m diameter lined running tunnel, three cross-overs and three new underground stations. The new stations have platform caverns of 20m span with similarly proportioned concourse caverns alongside. The ground is bedded sand stone and shale with high horizontal stresses. Predicted stress-relief induced ground movements during staged excavation led to innovative use of rock anchors for permanent support.

Jan 1, 2005

By Rixon K. L

Hargraves (1983) has reviewed the phenomenon of instantaneous outbursts of coal and gas with special attention to Australian occurrences. The purpose of this discussion is to highlight some problems and omissions in his review that reflect particularly on the authors' structural geological investigations of outburst-prone coal seams.It is surprising to find that much of the authors' reported work has either been glossed over or the results distorted by Hargraves (1983) and it is, therefore, important to clarify the contribution that structural analysis of coal seams can make.For many years it has been known that faults provided preferred loci for gas outbursts (for example, Briggs 1920-21) but the roie that faults played in outburstprone seams was unclear. The present authors reviewed the association of faults and outbursts drawing upon local investigations and the world-wide literature (Shepherd et aI., 1981), and discussed some wideranging aspects that result from the high coincidence of faults and outburst sites. Without repeating large segments of this article the authors will discuss four aspects of coal seam faulting and fracturing.

Jan 1, 1983

Due to highly competitive international coal markets, Stockton mine is bound to produce very high quality coals consistently if it is to maintain and expand its market share. The nature of the deposit is such that coals from various source pits are blended in differing proportions to meet the various coal quality specifications of the customer. The complexity arises due to quality variation within the seam both horizontally and vertically and the fact that up to six different products with completely different quality specifications may have to be produced. With increasing demand for this rare product and with CoalCorp eager to meet this demand comes the requirement for computer methods to handle this highly complex problem of both modelling and scheduling.

Jan 1, 1989

By Sun Chuanyao, Jia Muxin

Generally, if the bond valence (BV) between metal ion and oxygen of the mineral is greater than 0.8, only surface species –Me-O-H or –Me-O exposures on the mineral interface, if the BV is between 0.2-0.8, the metal ion exposures on the interface, and if the BV is less than 0.2 the metal ion dissolves into water. The PZCs of oxide minerals and island silicate minerals are determined by the bond valence of the bond in the mineral crystals, the higher the bond valence the lower the PZC of the mineral. So the PZC sequence of Al2SiO5 minerals is kyanite> andalusite> sillimanite. The general rule for framework silicate minerals is as: The higher the Al content, the lower the PZC of the mineral, when the ratio of Al to Si in the tetrahedron skeleton is below 1:3. The higher the Al content, the higher the PZC of the mineral, when the ratio of Al to Si in the skeleton is between 1:3 and 1:1. The general rule for layer silicate minerals is summarized as: the three-layer silicate minerals have much lower PZCs than that of the two-layer silicate minerals. The threelayer silicate mineral with the octahedron layer occupied by lower charged cations has lower PZC than that of the three-layer silicate mineral with the octahedron layer occupied by higher charged cations. The twolayer silicate mineral with the octahedron layer occupied by lower charged cations has higher PZC than that of the two-layer silicate mineral with the octahedron layer occupied by higher charged cations. The layer silicate mineral with Al substitution in the tetrahedron layer has lower PZC than that of the layer silicate mineral without Al substitution in the tetrahedron layer. Such pyroxene minerals whose M1 is occupied by a trivalence cation and the M2 is occupied by a monovalence cation has lower PZCs than those both M1 and M2 are all occupied by bivalence cations. Such hornblende minerals whose M2 is occupied by a trivalence cation and the M4 is occupied by a monovalence cation has lower PZCs than those both M2 and M4 are all occupied by bivalence cations. There is no Si4+ or 4 coordinated Al3+ exposures on the surface of framework silicate minerals, the metal ions of three layer or chain silicate minerals are compact between tetrahedron layersor chains, they hinder the metal ions to interact with oleate acid radical, the metal ion octahedron layer exposures on the surface of a two layer silicate mineral, but the the oleate acid radical can not attach to a metal ion by replacing a –OH- that connects three metal cations in the same time, So the floatability of such silicate mineral is bad. The metal octahedron chain style of an island silicate mineral affects it floatability, the mineral exposures octahedron chain metals with two dangling bonds in two directions floats better than the mineral exposures octahedron chain metals with two dangling bonds in one direction.

Jan 1, 2003

By M Swart, H Ståhlbröst, P Toor

Development of SAG liners has always been a strong focus and interest in mineral processing as SAG liners significantly impact on plant performance (throughput and grind size), material costs and plant downtime. SAG shell relines typically determine the frequency and duration of plant shutdowns. Early SAG shell liner designs relied heavily on practical experiences and were limited in their size due to weight restrictions. Significant developments in Discrete Element Method (DEM) modelling, material and manufacturing technologies and larger reline machines have resulted in new and improved liner designs. This paper discusses the evolution of SAG shell liner design and its progression to the Skip Row design. Case studies have been provided for the Skip Row design in a variety of applications such as Single Stage SAG (SSS), SAG and Ball (SAB), SAG and Ball with Crushing (SABC) and Pre-Crush at a variety of mill diameters ranging from 24 foot to 34 foot. A detailed assessment has also been carried out comparing liner service life, ease of reline and performance (throughput, power and grind size) for a large 34 foot SAG mill when compared to the previous design.CITATION:Toor, P, Swart, M and Ståhlbröst, H, 2017. The evolution of SAG shell lining and introduction of the skip row design, in Proceedings MetPlant 2017, pp 158–184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By Arturo Ressi di Cervia

From the times when men in lacustrine environments drove wooden piles into the mud to elevate their dwellings, until the beginning of the twentieth century builders reacted to the conditions found in the location of their proposed structures by attempting to distribute their loads in ways that could be supported by the foundation's soils; or, if those were unsuitable, by moving the structure, whenever possible. While many major structures were built on stable ground (the pyramids were founded on rock), others were built on [ ]

Jan 1, 2000

By J. A. Finch, Zhenghe Xu, Z. A. Zhou

Whether the microscopic bubbles generated by the high energy dissipation and high feed-slurry velocities in new flotation cells are stable in solution and what roles they play in particle collection are of great interest for the flotation of fines. Experimental work has shown that, with fast flow of liquid through an orifice, stable microscopic bubbles can form in flotation systems by hydrodynamic cavitation in the absence of gas supersaturation. The minimum flow rate at which bubble formation is initiated varies from 8 to 15 m/s, depending on the design of the cavitation tube, which is within the range of feed slurry velocities of some newly developed cells. Feed aeration enhances the formation of micro-bubbles by hydrodynamic cavitation. The study suggests that the fast flotation kinetics of some new cells may be attributed in some degree to the formation of microscopic bubbles

Jun 21, 1905

By Camilla Favaretti, Benjamin Turner, Anne Lemnitzer

Pile foundations are extensively used in the construction of various types of superstructures, including tall buildings, bridges, freeways and offshore structures. A fully constrained tip embedment such as a rock-socket offers an attractive solution for achieving significant tip resistance and improving the load-carrying capability of the foundation element. In profiles with very soft surficial soil, rock-socketing often provides the only reliable source of axial and lateral resistance. In preparation of a large-scale testing program on rock-socketed piles at UC Irvine (UCI) geared towards studying the magnitude of shear amplification at the rock-soil boundary of pile foundations, a pre-test model-scale experiment was executed in the UCI Structural Laboratory. The objective of the model-scale experiment was to iterate and validate the test setup, study the influence of important boundary conditions, assess instrumentation techniques and sensor placement, and to gain preliminary insight into the small-scale specimen non- linearity. In addition, this model-scale study provides ample opportunity to compare lateral performance parameters with analytically predicted lateral load behavior using traditional soil resistance functions and limit state analyses and explore new techniques for the derivation of soil resistance functions. The pile specimen had a pile diameter (D) of 10 inches and a total pile length of 125 inches. The pile was embedded in a 40 inch simulated rock socket overlain by 52 inch of medium dense sand (DR~50%). The pile extended 32 inches above the soil surface, where cyclic lateral loading was applied. The pile was installed in a laminar metal frame box with inside dimensions of 39 inches in width (W), 73 inches in length (L) and 86.1 inches in height (H) as shown in Figure 1. During testing, the box was restrained using a rigid bracing system consisting of concrete reaction blocks, wooden braces and steel girders.

Jan 1, 2018

By Stephen C. Tadolini, Thomas M. Barczak, Peter (Yunqing) Zhang

A cooperative study was conducted with Emerald Coal Resources, L.P., an affiliate of Foundation Coal Corporation, and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of (partially) pre-driven longwall recovery rooms supported with pumpable roof supports. This paper evaluates the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 10 ft from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 6-8 in once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 32-ft horizon with total deformation ranging from 2 to 4 in, indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. It is postulated that this may be due to the progression of the rear “abutment” moving toward the recovery room as the panel fender and standing support in the recovery room yield and shed load. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in roof instabilities that can lead to catastrophic results.

WHEN making comparisons of the efficiencies of different grinding and crushing machines it is desirable to be able to estimate the work actually done in crushing the ore from a given size of feed to a given size of product, the screen analysis of both feed and product being determined. Messrs. Klug and Taylor, in a paper on this subject, published in the monthly journal of the Chamber of Mines of WA, 31st January, 1906, have described a method adopted by them in calculations made in connection with a series of trials of grinding pans. Their methOd is based upon the assumption that if a quantity Q of material consisting of particles of average diameter x be crushed down until the average diameter of the particles is y, then the work done in grinding is proportional to Q x. There is no theoretical basis for this assumption that the writer is aware of, and it does not appear to satisfy the fundamental conditions necessary. If the material be further crushed until the diameter 2 becomes Z, the additional work done is measured. The work done in crushing from diameter x to diameter Z in one operation is proportional to Q x:, and therefore we ought to have zx2 y2 x2 Q-+Q-=Q-. y2 Z2 Z2But these expressions are not in general equal to one another. In other words, according to the theory underlying this method, if we crush from diameter x to diameter y, and then from diameter...

Jan 1, 1909

By L. K. Bandyopadhyay

The expert system component of Knowledge Base System supports the analysis and interpretation phases of ventilation design with an algorithmic program used for the solution of alternate design. The paper describes the ?ES-VENT? knowledge based system developed at Central Mining Research Institute, Dhanbad, India for an on-line diagnosing of the ventilation problems using the ?IITMRULE? expert system development tool. In the ?IITMRULE? expert system tool, it has been decided to use a backward chaining reasoning process to reach the goal state i.e. the final conclusion. ES-VENT system is made of three modules: On-line Data, Diagnostics and KBS. Each module is being a collection of several programs. The paper mainly deals with the parameters affecting the ventilation of underground mines such as air-velocity, air pressure, temperature, dust, and humidity and gas contents. The graphical presentation of these parameters on the computer and the interactive part of the developed program is expected to help a ventilation officer to determine the changes in a ventilation circuit necessary to bring the mine ventilation to the desired value. Once such changes are physically effected, the display will indicate if the changes have brought the desired effect or not on ventilation. Keywords: Ventilation network, on-line data, expert system, intelligent system, knowledge base, inference engine.

Jan 1, 2002

By R. J. Durrheim

The DEEPMINE Collaborative Research Programme was established to create the technological and human resources platform that would make it possible to mine gold safely and profitably at depths of 3 to 5 km. The DEEPMINE Programme has four goals: to acquire knowledge of and develop appropriate technology for new ultra-deep level mines, to stimulate education and training, to establish a culture of innovation, and to encourage rapid technology transfer and implementation. The research programme was launched in July1998 and will be completed in March 2002, with the final year focusing on the transfer of knowledge to the industrial partners. DEEPMINE represents a new model for conducting mining research: it is driven by industry needs; emphasizes collaboration between industrial partners, research organizations and tertiary education institutions; and has a novel joint-funding mechanism. DEEPMINE has employed a range of vehicles to transfer knowledge to its industrial partners. Novel aspects include: (a) electronic publication of Summary Reports and Guideline Handbooks that seek to consolidate the huge body of knowledge comprehensively and concisely, (b) a series of DEEPMINE Schools designed to enable industry practitioners to apply the knowledge to their current work situation, and (c) Consultancy Reviews, where DEEPMINE specialists seek to apply knowledge to specific real problems on mines.

Jan 1, 2002

By W. W. Krech, T. E. Perkins

As fractures are propagated through rocks, energy is absorbed near the extending crack tip. Apparent surface energies for several rocks have been measured by cleavage under dynamic con-ditions. At nominal crack velocities from 0.5 to 500 in (min, measurements showed that fractures propagated in discrete jumps. Calculated surface energies and moduli were relatively insensitive to nominal rate of cleavage. in another set of experiments, rocks were cleaved under high confining stresses. The rocks were submerged in low leak-off fluids which formed a filter cake on the freshly cleaved surfaces (similar to the hydraulic lracturing process). Apparent surface energies were increased substantially as the surrounding fluid pressure was increased. Moduli in bending increased significantly upon application of the first 1,000 psi but were insensitive to stress level at greater pressures. INTRODUCTION For almost 20 years, hydraulic fracturing processes have been utilized effectively to stimulate oil and gas wells. During this period, some process improvements have resulted from studies of fracture orientation, mechanics of fracturing, areas generated, conductivities of cracks, etc. Yet many questions remain concerning the conditions and pressures needed during fracture propagation. In this paper we will report additional studies of the mechanics of fracture extension. It was shown previously3 that large rock samples could be cleaved under controlled conditions so as to measure the apparent surface energy (that amount of energy absorbed per unit area of new surface created). In this paper we consider the effects of two additional factors on surface energies, viz.: (1) effect of cleavage rate and (2) effect of confining stress level. THEORY Cleavage experiments were conducted on rock samples similar to that illustrated in Fig. 1. Blocks of rock several inches wide, 2- to 3-in. thick, and up to 3 ft in length were grooved longitudinally with shallow guide slots. A crack was initiated and allowed to extend along the web as the top of the rock specimen was pulled (or pushed) apart. Auxiliary equipment permits the measurement of (1) force applied at the top, (2) separation at the top and (3) crack length. (Further experimental details will be given in the next section.) The rock beams created by the crack are considered ton be cantilever beams. The deflection (or separation of the rock beams) at any point is calculated 4,5 by the beam Eq. 1.

Jan 1, 1967

By Frank Sames

The control of the environmental effects, especially blast vibration and airblast, has become a dominating planning criterion for most surface blasting operations. Compliance with existing regulations is generally achieved through constraints in the blast design, or monitoring programs. Commonly, blast vibration and airblast signals are rated and compared only by their maximum amplitude and the principal frequency associated with the peak.

Jan 1, 1997