Search Documents

By S. M. Shelton

Ferrograde manganese ore or its equivalent is essential to the manufacture of every ton of steel produced; although it is well-known that there are largo deposits of low-grade ore in the United States, production of substantial amounts of ferrograde material from domestic sources presents a problem that becomes more and more critical as the stock piled ore is depleted through inability to obtain adequate supplies from foreign sources. Consequently, a program of laboratory and pilot-plant investigations designed to solve the problem of obtaining a domestic supply of manganese has been undertaken by the Metallurgical Division, Bureau of Mines. This paper is one of a new series that will include reports of results obtained in the various investigations conducted under the manganese program. The scope of the program and the organization that was set up to direct and supervise the work were discussed in the foreword of the first paper of this series, Report of Investigations 3506, Manganese Investigations 1. Concentration of Manganese Ores from the Drum Mountain District, Utah, by S. R. Zimmerley, J. D. Vincent, and C. H. Schack. Other reports will be published as the work progresses.

Jan 1, 1942

By Lewis C. Karrick

Although the Bureau of Mines has thus far made no large-scale experiments with oil shales, and the feasibility of the commercial manufacture of shale-oil products suited to present market requirements has not been demonstrated, there is ample reason to believe that these products will eventually supplement the more commonly used petroleum products and give equally good service. In 1919 the bureau, in cooperation with the Department of Metallurgical Research, University of Utah, began investigating the oil shales of the United States to obtain detailed information on their value. The States of Colorado and Indiana also cooperated through their State universities, in which research laboratories were organized to assist in carrying on the oil-shale studies planned and directed by the bureau. As a result of these studies much information is now available concerning laboratory methods of producing the greatest yields of the best products from oil shale. In order to study the principles that govern the retorting of oil shales and to test the oils produced, it has been necessary to develop and standardize reliable apparatus and methods for distilling shale, and to adapt to the testing of shale oils some of the methods the Bureau of Mines uses for testing petroleum. The methods employed by the Scottish shale-oil manufacturers were also studied, but most of them have been superseded by those described in this bulletin, which give more comprehensive and accurate results and employ more convenient apparatus. This paper is presented, therefore, as a manual of apparatus and methods that the bureau has developed for work on oil shale and found satisfactory for routine tests and for research. Explanation and discussion of the principles underlying the methods of testing are included wherever necessary for a clearer understanding.

Jan 1, 1926

By H. Yilmaz

A testing method for assessing the shear-bond strength of thin spray-on liner (TSL) on rock substrate was developed at Wits University Rock Mechanics Laboratories. The gap between a 20 mm thick steel ring and a rock core is filled with TSL along the depth of the ring. After the curing of the TSL for a predetermined period, the sample is placed on a base, which offers support to the steel ring and the TSL but not to the rock core. A compressive load is applied on the rock core displacing the core on TSL contact and punching it towards the void in the support base. Shear-bond strengths for different TSL products as well as shotcrete were measured. This paper describes the test set-up and points out the important aspects and procedures during sample preparation and test execution. The test results are also presented and discussed.

Jan 1, 2007

A Novel Diagnosis and Evaluation Procedure for Flotation Plants

Sep 13, 2010

By R. Luhrman, E. Christ, B. Gores, S. Fischer, E. Johanning

North American railroad locomotive operators (engineers and conductors) are exposed to multi-axis vibration and shocks (1, 2). A recent epidemiological survey showed a prevalence of serious type of neck and lower back disorders nearly double that of a control group (3). Ergonomic working conditions are important co-factors in a vibration and shock exposure risk assessment (4, 5). The goal of this study is to illustrate typical work stations (cabs and seats) in US/Canadian type locomotives and assess shock related exposure risk by calculations of the new proposed shock risk indicators according to the new ISO 2631-5 (2004) (6). Methods Locomotive cab and seat inspections were conducted and operators’ activities were assessed by a trained observer. Field measurements (n=50) were obtained during normal revue service following generally accepted guidelines (ISO 2631 (1)). A sub-sample of n=20 locomotives were selected for the calculation of proposed shock indicators (ISO 2631 (5)). Results There has been little change in basic locomotive cab and seat design in the U.S.. Two locomotive cab design concepts are used: the Association of American Railroad (AAR) Control Stand and in newer series wide-body locomotives the “Control Consol” (Figures 1-2), with varying seating conditions, but frequently subjecting the operator to an awkward body posture in addition to the vibration and shock exposure. [ ]

Jan 6, 2006

By Steve Klein

Weak rock is an important consideration in tunnel design and construction due to the difficult ground conditions that are often encountered. Nevertheless, when conditions are favorable high advance rates can be achieved leading to economical tunnel construction. Successful construction of a tunnel in weak rocks depends on correctly anticipating the behavior of these unique materials. The objective of this paper is to provide guidelines that can be used to accurately classify the performance of weak rock in tunnels.

Jan 1, 2001

By Wolfgang Roth

In 1990, a residential area above the North Outfall Sewer (NOS) tunnel constructed in 1924, experienced subsidence. After sewage was diverted into the North Outfall Replacement Sewer (NORS), soil probing from within the tunnel was conducted, soil-improvement options were developed, and a preferred grouting scheme was analyzed by numerical modeling to evaluate the stability of the 80-year+ old tunnel liner under grouting-induced loading conditions. This paper discusses the initial field investigation and the development and analysis of a grouting scheme originally intended to be implemented before relining of the tunnel. The scheme was later modified, and the new liner was installed before the final probing and grouting work was done.

Jan 1, 2008

By E. Yalçin

The data set often contains one or more secondary variables. These secondary variables are usually spatially cross correlated with the primary variable. The addition of the cross-correlated information reduces the variance of the estimation error by using the cokriging method. The grade estimation results of ordinary kriging and cokriging methods are evaluated and it was found that the estimation variance of cokriging method is slightly lower than ordinary kriging. The effect of variation of block dimension on the estimation results is also investigated and it was seen that the cokriging estimation variance values also decrease as the block dimension increases.

Jan 1, 2005

By Francisco Sena Leite, Pedro Brito, Gean Frank, PhD Soeiro de Carvalho, Jose, Vinicius Miranda

The consequences of rock blasting with explosives are directly related to the accuracy of drilling and, because they have an effect on fragmentation and ground level, they should be controlled to ensure a problem free production, increase work safety and reduce environment impact. Safety control is one of the most important processes in detonation, since it can compromise the worker security on site and, eventually, neighboring communities. Due to the technology advancements, it is possible to build a hole deviation control device with “of the shelf” parts, and for that reason the authors decided to evaluate the possibility of measuring hole deviation by creating a portable prototype using an electronic sensor capable of measuring the acceleration on objects, that is, to measure the own acceleration of a system, known as "accelerometer" and a micro-controller to handle and treat data. The main idea behind this paper is to validate the power of the Euler method, given the stepping limitations of the sensor and micro controller in order to reproduce of the hole shape. A case study was carried out, comparing the measurements of borehole deviations made by a traditional equipment and the prototype. A mobile application was also created in order to recover and treat and display the data to the user. For validation of the prototype, several holes were measured using the two devices. A residue analysis was used to validate the data obtained. After analyzing and confirming the effectiveness of the new equipment, the normality tests prove a symmetric distribution with null expected residual mean and minimum variance. Consequently, the accuracy of the prototype is evidenced. Thus, the authors aspire to emphasize the potential of using these sensors allied to a traditional numerical method for analysis of hole deviation.

Jan 1, 2019

By James W. Cassie

The Snap Lake Diamond Project is located approximately 220 km northeast of Yellowknife, NT, Canada at an approximate latitude of 63?35?. The project location is within the zone of continuous permafrost; measured ground temperatures are about ?2?C at 10 to 20 m depth below surface. The site is located on a peninsula jutting into Snap Lake. The site is generally barren of vegetation, except for some isolated areas with low trees located in topographic lows and near the shoreline of Snap Lake. As part of phased evaluation process with regards to the mining project, an Advanced Exploration Program was undertaken in 2000 and 2001. This program included the underground extraction of a bulk sample of kimberlite, which was processed on site. A Processed Kimberlite Containment (PKC) area was required as part of this program. The area chosen as the PKC facility was a small inland lake, called Inland Lake #1, on the peninsula. Construction of the PKC area required the construction of two dams, one on either end of the lake. At the south end of the lake, Dam 1 was constructed partially on a talik and partially on continuous permafrost. Dam 2 was constructed entirely on permafrost. The effects of the remote location, selection of suitable construction materials and permafrost conditions on the designs of the dams are discussed. A description of the design elements and construction schedule are provided. A review of the performance of these two dams, in terms of settlement, deformations, pore pressures and thermal regime, over the last several years is provided.

May 1, 2003

By E. B. Johnson

Cleveland-Cliffs lron Co., which operates Marquette lron Mining Co.'s Republic mine, conducted a test whereby 35,000 tons of self-fluxed pellets were produced in the grate-kiln system from specular hematite flotation concentrates. A brief description of the pelletizing plant is presented along with pertinent operating details. Date is included which compare operating conditions and the chemical and physical properties of the green and fired pellets for the self-fluxing pelletizing test with the normal acid pelletizing operation. The success of self-fluxed sinter in enhancing the operation of the blast furnace during the past few years has reasonably led to the assumption that the use of self-fluxed pellets might result in even greater furnace efficiencies. A great share of development work in agglomeration has been directed towards techniques related to the production of self-fluxed pellets, but only a limited tonnage of self-fluxed pellets had been produced on a commercial scale until this past year when The Cleveland-Cliffs Iron Co. produced 35,000 tons of such pellets by the grate kiln system at the Republic mine during the period May 21-June 5, 1962. REPUBLIC'S GRATE-KILN PLANT The grate-kiln pelletizing process consists of four stages, namely: feed or balling circuit, traveling grate, rotary kiln and annular cooler (Fig. 1). The balling section is conventional and utilizes four 9x30-ft balling drums in closed circuit with 5x14-ft vibrating screens having 3/8-in. rod decks. The traveling grate is 12 ft wide by 126 ft long and has 14 windboxes — six in the drying section and eight in the preheat section. The rotary kiln is 15 ft ID shell and 114 ft long. The annular cooler is 40 ft in diameter and has 12 windboxes. The cooler is divided into two zones by a moveable curtain wall. The high temperature air from the first zone is used as secondary combustion air in the kiln. Normally the only heat supplied is through the burning of No. 6 oil in the single kiln burner. Hot gases pass counter to the pellet flow through the system. The exit gases from the kiln pass down draft through the preheat section through cyclones and are drawn through the drying bed prior to exiting via the stack. The temperatures are normally held within the following ranges: Kiln 2400-2445 °F Preheat 1850-1950°F Drying 480-520°F Exit gas 200°F Pellets 120°F The design capacity of the Republic mine grate-kiln system was 2500 Itpd. Sustained production in excess of 35% over design capacity has been achieved. No screening of the cooler product is practiced. PELLETIZING TEST CONDITIONS When a decision was made to proceed with a test at the Republic mine pelletizing plant to produce 35,000 tons of self-fluxed pellets, several potential failure factors had to be carefully considered. Research work on a batch and pilot plant scale indicated that the grate-kiln system at Republic would require some major changes in order to obtain optimum conditions. In many cases compromises were agreed upon as major equipment changes and revisions were not feasible. The pelletizing conditions which laboratory development tests revealed were required in order to insure successful production of self-fluxed pellets were: 1) Good mixing of limestone and concentrate and proper moisture control; 2) Higher gas flow rates in the preheat section than are normally used; 3) Higher preheat temperatures than normal; 4) Maximum kiln temperature 2350°F. There was just cause for concern about balling problems that might occur. Approximately 10% of dry pulverized limestone was to be added to the specular hematite concentrate just ahead of the Pekay mixers on the belt feeding the balling drum. Large scale

Jan 1, 1963

By Helvio Pessanha Guimarães Santafé Jr.

The coir fiber extracted from the husk of the coconut has been extensively used as polymer composite reinforcement in a variety of industrial applications ranging from civil construction to automobile seat cushions. The hydrophilic coir fiber does not act as an effective reinforcement owing to its low interfacial strength with hydrophobic polymers. As a consequence, coir fiber composites display relatively low mechanical strength. The objective of this work was to investigate the effect of an acetylation treatment of the coir fiber surface on the mechanical behavior of epoxy composites with amounts of fibers up to 30% in volume. Coir fibers were immersed in an acid solution of acetic anhydride for one hour, washed and dried, before mixing with DGEBA/TETA epoxy to fabricate the composites. Flexural mechanical properties were obtained by bend tests. The results showed significant differences to similar composites with alkali treated coir fibers that have been previously investigated.

Jan 1, 2010

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions 5/ issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1962

By M Baker

Biodiversity offsets are conservation actions intended to compensate for the residual, unavoidable harm to biodiversity caused by development projects. The use of biodiversity offsets in the context of mining has significant potential for enabling mining to take place in areas with biodiversity values, where it would not otherwise be possible to meet the relevant legal tests under the Resource Management Act 1991, and potentially the Conservation Act 1987. This paper looks at the concept of biodiversity offsets (and environmental compensation generally) both in New Zealand and internationally, and considers how lessons learned overseas may be adapted for this country. In New Zealand the practice of biodiversity offsets and environmental compensation is ad hoc and variable. The challenge with biodiversity offsets is to establish a transparent and coherent means of identifying the overall priorities and objectives of adopting such an approach, as well as how the relevant values are measured and protected. Establishing a methodology for quantifying biodiversity value, and the need for clear policy guidelines on biodiversity offsets are identified as key areas in need of wider discussion.

Jan 1, 2007

By William R. Yernberg

The combined 80th Annual Minnesota Section of SME Meeting and 68th Annual University of Minnesota Mining Symposium was held April 17 and 18, 2007, in Duluth, MN. About 350 mining industry professionals attended the conference, including engineers, executives, mining managers and suppliers from the United States, Canada, Australia, Finland and Brazil. This year’s theme was “Consolidation – Growth – Technology.” The 80th Annual Minnesota Section of SME meeting included concurrent technical papers sessions, a keynote session that featured two distinguished speakers and a general managers session in which taconite mine operators provided updates on their operations. The Minnesota Section meeting also offered an SME short course titled “Control the Feed, Control the Mill.” More than 50 individuals at-tended the short course.

Jan 1, 2007

By Kurt Oakes, Paul Worsey, Braden Lusk, Tony Brasier, Scott Crabtree, Randy Wheeler

Theoretical description of destructive wave interference and the use of sacrifi cial holes is included and is supported by data collected at Springfi eld Underground. Finally, the process by which the reduction in vibration was achieved in practice is described. Results are discussed for several production blasts taking place over a one year period.

Jan 1, 2008

By Frances Badelow

This paper describes a design process for piled raft foundations supporting high-rise buildings. The design process comprises an initial stage of geotechnical site characterization using the results of investigation boreholes to prepare a subsurface model and derive geotechnical parameters for raft and pile design from empirical correlations. Following this a preliminary analysis is undertaken using a combination of elastic theory and allowances for non linear behaviour of the piled raft system to assess the viability of such a foundation system and any potential advantages of a piled raft over conventional fully piled foundation systems. Finally, a detailed analysis is undertaken using the GARP8 computer program. Case studies where this design process has been successfully used to design a more efficient piled raft system that has resulted in significant cost and time savings compared to conventional bored pile foundation options are also described.

Jan 1, 2006

By N. Grosland, G. Kopp, T. Hunstad, D. Wilder, M. Contratto, S. Rahmatalla, T. Xia

Chronic whole-body vibration exposure, as expected in large construction and mining vehicles, has been associated with neck and back pain and injury.1 While work has been done towards gaining a better understanding of the relationship between vibration and shock and muscle activity of the back musculature2, relatively little information regarding the activity of neck, shoulder and upper arm muscles is known. Today’s equipment designs must conform to domestic and international standards, however these standards do not specifically address the vibration exposure in the head and upper quarter. Further it is not well known how the control configuration within a vehicle (e.g. steering wheel versus arm controls) influences muscle voluntary and reflex activity levels. Greater muscle activity may lead to greater muscle fatigue – which in turn may be associated with greater risk of injury.2 Thus, muscle contractions needed to maintain static postures as well as those resulting reflexively should be considered during an analysis of seating position. Unfortunately, little is known regarding the influence of arm position on head and neck muscle function. The purpose of this study was to investigate the relative muscle activities of 5 neck, shoulder, and upper arm muscles during riding simulations of large construction equipment, using three different arm control options. Methods Five typical heavy equipment ride files were “played back” through a man-rated Servo Test 6-degree of freedom (dof) vibration system. Each ride was repeated using 3 seat and control configurations (steering wheel (SW), floor mounted arm-rest controls (FM), seat mounted arm-rest controls (SM)). Two trials were performed for each ride and seat control combination (each trial: 60 sec of 6-dof and 60 sec of vertical vibration). Five channels of surface electromyography (EMG) of the right-side cervical erector spinae muscles (neck extensors), sternocleidomastoid (neck flexor), upper trapezius (shoulder elevator), biceps brachii (elbow flexor) and triceps brachii (elbow extensor) muscles were collected throughout each ride (~ 2min) using pre-amplified (10x), 1 cm silver bar electrodes, with 1 cm fixed inter-electrode distances (Delsys, Inc). Further analog amplification was set at 10k (1k for one subject), and sampled at 1000Hz using a 12-bit DAQ card and Labview 7.1 software (National Instruments). A total of 7 right-handed male subjects were tested, but only 5 had complete EMG data sets to analyze for this sub-study. EMG was analyzed using root mean square (RMS, in mV) of 20 ms moving windows, and then averaged across the entire trial for a measure of mean total muscle activity (voluntary and reflexive). The muscle activity to maintain the static posture was estimated as the mean RMS EMG over a 1 sec interval just prior to and/or after completion of the ride. Repeated Measures ANOVAs were used to test for with-in subject differences using a = 0.05.

Jan 6, 2006

By T. G. Carter, R. I. Miller

First, the influence of variation in the

Apr 1, 1995

By Misra V. N, Cheng C. Y

Two types of Mt Tom Price hematite iron ore from Hamersley Iron P/L were tested using a Humboldt Wedag Jones P40 wet high intensity magnetic separator (WHIMS). The parameters tested were magnetic intensity (7000, 9000 and 11 000 Gauss), groove plate type (8R and 12R) and gap width (2.5 and 1.8 mm). It was found that at 9000 gauss magnetic intensity, reasonably high-grade and recovery in the concentrate were obtained. At 2.5 mm plate gap width, the 12R groove plate performed slightly better than the 8R groove plate. Further testwork is recommended to optimise the magnetic intensity, feed flowrate and pulp density, wash water pressure and flowrate with 12R and 8R groove plates at 2.5 mm gap width.

Jan 1, 1999