Search Documents

By Tom Short

"Construction blasting covers a very extensive variety of explosive applications. I will discussseveral of these with you and then show slides from my collection, starting in 1956, which will betterillustrate the types of blasting under discussion."

Jan 1, 1991

Rehabilitation, reclamation and restoration are all terms used to describe the repair of land after mining. Here, restoration is used to mean restoring the land's original use, capability or productivity. Effective restoration is dependent on good planning before mining commences and must include a clear definition of post-mining objectives. The physical condition of the land within the mining licence was that of an imperfectly drained soil in permanent pasture, supporting a seasonal supply dairying unit. During the mining process, the soil layers were separated, with the topsoil stockpiled separately. As part of the restoration process, the land was recontoured to encourage surface drainage, with topsoil spread evenly over the recontoured tailings. Low grond pressure machinery was used to minimise soil compaction, with light discing and harrowing used to increase water infiltration. A permanent pasture was sown, with weed species controlled by spraying, both before and after pasture establishment.  Soil testing has been used extensively to ensure there were no nutrient deficiencies that good compromise pasture establishment and performance. Controlled grazing practices were used to ensure that the sown pastures became well established.

Jan 1, 1998

By Cassandra A. Wetzel

Rock socketed mini-piles are a desirable foundation alternative when design capacity is more than 40 tons and there is limited access. In this case history mini-piles were designed to support between 75 and 200 kips at 12 locations adjacent to a perimeter wall, a party wall and at cast iron column piers. Limited geotechnical information, low overhead clearance, and active building population tested the creativity of the team to get the piles installed. The key geotechnical concern during installation of the mini-piles was the presence of a glacial till layer above the bedrock surface that restricted the seating of the casing into bedrock with a track mounted drill rig. Soil loss during the advancement of the rock socket using an air hammer was excessive and increased the risk of subsidence. Over a three week period the engineer worked with the contractor to modify the design, means, methods, and materials to install piles with adequate load capacity. This paper will present the changes in design and construction methods that were required.

The New Zealand Steel Ironsand Slurry Pipeline was successfully commissioned in February 1986. The project includes 18 km of high pressure, polyurethane lined buried pipe. McConnell Dowell Constructors Limited has developed a coupling which has allowed this pipeline to be fully welded. The design and development of the coupling and its application on this project is discussed.

Jan 1, 1986

By Staff

One hundred thousand miles of flying over the North country without a single air casualty; much of it over virgin territory probably never before visited by white men; some of it over regions that abound with possibilities for minerals; all of it effective, for exploration and the establishment of bases and supply-stations, and for the carrying of men and their tools and provisions- this, briefly, is the record of Northern Aerial Minerals Exploration, Limited, a Canadian company organized Jess than nine months ago, which has been functioning, without interruption, during spring, summer, and now into winter. Our planes have ranged from the Alaskan boundary on the west to the Labrador coast on the east, and from the Transcontinental railway north to the Arctic circle. Our prospectors, carried on trips of hundreds, and occasionally thousands, of miles, have gone over large sections of country which were never before explored, and at the end of the prospecting season the Company finds itself in possession of several groups of important gold claims, which look most promising. In addition to this, we have been in contact with deposits of almost every known mineral.

Jan 1, 1929

By Stewart A. Silling, Dale S. Preece

The two key results of rock blasting are fragmentation and movement of geomaterials. Movement/flow of the blasted rock is often referred to as heave. Modeling the movement of full scale blasting is now possible with 3D distinct element models and parallel processing.

Jan 1, 2016

By L. Nahai

THE OUTPUT ff the mineral industry in 1964 in both non-Communist and Communist Europe showed an upward trend for most countries in keeping with the higher index of overall industrial production. Comparable indexes of mineral industry production for non-Communist and Communist Europe (including the U.S.S.R. in Asia) are not available, primarily because the U.S.S.R. does not report details of its industrial production by industrial sectors. However, available data both in the form of index numbers on production published by the United Nations and based on data as reported to the United Nations by the various countries, and actual production data for selected major commodities published by the various European countries reflect generally expanded output by both the extractive sector and the processing sector of the mineral industry in most of the 26 nations of Europe.

Jan 1, 1966

By William R. Yernberg

SME’s Arizona Conference was held at the Doubletree Hotel at Reid Park in Tucson on Dec. 5and 6, 2004. The annual conference is organized by the Arizona Conference Board of Directors, which represents SME sections in Arizona and adjacent areas. The conference provides an opportunity for individuals and corporations associated with mining in the region to get together each year to discuss the status of the industry. The meeting featured a keynote address and more than30 technical papers. Two years ago, the U.S. copper industry was facing on a run for two years now,” and “both precious metal and base metal prices are going up.” The increases in metal prices were attributed to development in China and other Asian countries. “With a population of 1.6 billion, China has recently created 80 million jobs,” said Silver.

Jan 1, 2005

By W. Petruk

Mineralogical studies and concentration tests were conducted on samples from an oolitic iron deposit from the Peace River district in Alberta to determine what concentrate grades and metal recoveries could be obtained. The samples assayed 32 to 37 wt. % Fe, and consisted of goethite, nontronite, ferruginous opal, siderite , quartz, amorphous phosphate and illite . Flotation with fatty acids yielded the best over-all results. A flotation concentrate from a composite sample of the iron horizon assayed, by weight, 43.0% Fe, 12.3% SiO2 , 1.9% CaD, 0.9% MgO, 4.5% Al2O3 and 2.0% P2O5 and lost 17.2% on ignition, for an iron recovery of 48.8% and a silica rejection of 80%. When heated to drive off the water, the concentrate assayed 52 w t. % Fe and 14. 8% w t. % SiO2

Jan 1, 1977

By A. L. Worthen

This is one of a series of pacers being published by the United States Bureau of Mines, describing mining and milling methods at crushed-stone plants throughout the United States. These pacers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total production costs. Although the publication of total production cost might not be advisable in some instances, yet a knowledge of operating costs is essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called o this differentiation in order that there will be no misunderstanding of the scope of the cost tabulations. This paper deals with the quarrying and crushing methods used at the Plainville plant of the New Haven Trap Rock Co., which produces annually between 275,000 and 300,000 tons of trap rock, Although pct the largest quarry operated by the company, it typifies the standard methods used by all the quarries in producing crushed stone and has one or two rather unique operating features. The cost of production at this plant is close to the average cost at all quarries of the company.

Jan 1, 1936

Rising energy costs are a growing concern among mine operators. At sur’ace operations, the size of a dragline, production requirements, pit geometry and layout, and operator skill are all factors in potential energy savings. The following tips are offered as a practical means to conserve energy demand, and can be applied to diesel fuel draglines as well.

Jan 7, 1980

By M. Y. Solar, W. G. Davenport

Most of the recent growth in nickel demand has been for the production of stainless steels and virtually all of it has been satisfied by new ferronickel and nickel pig iron projects. But "good" laterite resources are more and more difficult to find: Ni grades are decreasing while Fe contents are increasing and SiO2/MgO ratios vary from 1 to 3 and even higher if limonites are included. Predicting the smelting behaviour of such ores requires a more fundamental understanding of the thermodynamics of these systems in commercial operations. One valid question is thus whether these furnaces are at thermodynamic equilibrium or not. The present paper investigates this question, compares calculated and measured O2 partial pressures and mechanical/chemical slag loss ratios and concludes that ferronickel furnaces are not at thermodynamic equilibrium. This departure from expectation is actually to the operators’ advantage: the targeted ferronickel grades can be obtained at lower reduction potentials than calculated from pure thermodynamics.

Jan 1, 2014

By W. P. Diamond, S. L. Cario, F. Garcia, J. D. Byars, T. P. Mucho

The National Institute for Occupational Safety and Health (NIOSH) has been conducting research at a Pittsburgh Coalbed longwall mine to evaluate and optimize bleeder ventilation and gob gas venthole longwall methane control systems. Gas flow into these two methane control systems was investigated using a combination of Sulphur Hexafluoride (SF6)tracer gas studies and gob venthole pressure monitoring experiments. The insights gained from this research has facilitated the development of a longwall subsided strata methane control system conceptual model. This model provides the basis for design suggestions to increase the efficiency of the gob gas venthole system to permit the bleeder ventilation system to become a "safety net" for methane control.

Jan 1, 2000

By M. Nete

Qualitative analysis of three mineral samples from northern Mozambique was accomplished by X-ray diffraction (XRD), microscopy, scintillation, and magnetic determination. Chemical characterization was accomplished using ICP-OES and pressed powder XRF after dissolution using microwave-assisted digestion and flux fusion. The samples consisted of a mixture of minerals with tantalite as the major component, with minor amounts of microlite, quartz, mica, accessory garnet, and tourmaline. Incomplete dissolution was obtained using microwave digestion, with maximum recoveries of 90.25 ± 0.06% and 88.90 ± 0.04% for Nb2O5 and Ta2O5 respectively. Complete dissolution using Li2B4O7 resulted in recoveries of 98.5 ±0.2% Nb2O5 and 100.4 ± 0.3% Ta2O5.

Jan 1, 2012

By H. S. Fowler

The Consolidated Mining and Smelting Company has been in the business of mining and exploration since its incorporation in 1906. The Company has reports written as early as 1890. Consequently, its files contain a very large number of reports, and also of maps, of ail descriptions. REPORTS Before describing the filing of maps, a brie{ note on our general system of filing reports will perhaps clarify the discussion. Reports of a non-periodic nature, primarily those based upon examinations by field engineers, are separated from all other data and filed in what we know as the Mine Series System. Each property on which reports are written is given a serial number, known as the Mine Series Number. This serial number is assigned at the time the first report is filed and it remains permanently identified with the property, regardless of its state of activity. Our mine series numbers now total over 5,000. The serial number for a property may be found by referring to an alphabetical index of properties. MAPS We found it necessary to divide maps into two groups: (1) Maps of properties (2) Maps of areas

Jan 1, 1944

By H. V. Makar

Laboratory tests were performed to obtain a quantitative description of the effectiveness of sodium sulfate (Na2SO4) for removing copper from molten iron and to determine the effectiveness of Na2SO4 on actual auto scrap. The tests were conducted on induction melted heats of iron averaging 0.58 and 1.50 percent initial copper and on cupola-melted auto scrap containing 0.45 percent initial copper. The Na2SO4 was added in powder form in amounts ranging from 2.9 to 43.8 percent of the weight of iron being treated. The data showed that copper removal for the various Na2SO4 treatments followed a similar trend, regardless of the iron composition that was tested. The equation Y = 1 - e-3.23x approximately reflects the relationship between copper removal and amount of Na2SO4 added, where Y is the fraction of copper removed and x is the ratio of the weight of Na2SO4 added to the weight of metal treated. Copper removals ranged from 3.3 to 74.5 percent and reductions down to less than 0.10 percent final copper were achieved in the auto scrap. Copper removals were generally accompanied by sulfur removal, and initial sulfur contents ranging from 0.10 to 0.20 percent were reduced to as low as 0.02 percent. High temperatures and long slag reaction times tended to induce copper and sulfur reversion from the slag, but, generally, the Na2SO4 treat¬ments were effective up to approximately 2,820° F with reaction times not exceeding 7 minutes.

Jan 1, 1968

By D. S. Pye, J. P. Gallus

Successful hydraulic pressure treatment of oil and gas wells that have long producing intervals, multiple pay zones, fluid thief zones, or natural or induced fractures has long been a serious problem plaguing the petroleum industry. High fluid-injection rates, straddle packers, ball sealers, and either liquid or solid additives to the treating fluids are being used to cope with this difficult and costly problem.l-6 The use of ball sealers and straddle packers is limited, in practice, to wells that have been completed with perforated cemented casings or liners. Well stimulation with ball sealers and straddle packers is usually successful as long as the cement remains competent. The other techniques of diverting are used with all types of completions. However, there are two significant disadvantages of the high rate method: excessive horsepower requirements, and the need of large treating-fluid volume. Consequently, most well stimulation techniques that involve diverting depend upon ball sealers or granular materials. Liquid diverting agents, and some of the solid ones in use today, frequently will cause formation damage. On the other hand, the most popular particulate diverting agents often are so soluble in the treating fluid that they become largely ineffective; their particle size is severely reduced as they dissolve while being transported through thousands of feet of pipe to the formation face down hole. In our attempts to deal with the shortcomings of these diverting agents, we experimented with a large variety of potentially suitable deformable materials the solubility of which could be controlled. Following are the criteria for the diverting agent sought: 1. The material must be effective in reducing fluid loss to thief zones, including existing fractures and very high permeability layers in the formation to be pressure treated. 2. The material must have enough strength to bridge under the treating pressure. 3. The material must be insoluble or slowly soluble in the treating fluids so that the particles retain sufficient size to be effective after they reach the formation face. 4. The material must be completely soluble in the produced oil or condensate liquid so that it can be removed readily; it must not cause formation damage. A number of products consisting of various polymers blended with waxes and other solid hydrocarbons were examined. All these materials satisfied the criteria for a diverting agent and also exhibited some degree of plastic deformability. On the basis of initial tests of strength and hardness, several blends of wax and polymer were selected for extensive testing in the laboratory and the field. These compounds have congealing temperatures ranging from 140 to 190F; they are insoluble in water and soluble in oil. They conformed, therefore, to the criteria specified for a theoretically superior diverting agent. Laboratory and field tests were conducted using these wax-polymer materials to demonstrate that the use of a deformable diverting agent can significantly improve fluid diverting performance. Data in this

Jan 1, 1970

By G. Budge

In the extractive industry the term ‘continuous improvement’ (CI) usually means procurement of the latest state of the art equipment. This is generally perceived as the only way to add further value to the supply chain, with the driving philosophy of increased tonnage to dilute operational costs. However, not all market places can facilitate this approach. RJB lives in a fiercely competitive market and has targeted the standard efficiency drivers of rationalisation and stock management with a vengeance; and also operate CMMS (Computer Maintenance Management System), RCM (Routine Condition Monitoring)and CBM (Condition Based Maintenance) methodologies. Ultimately though, these systems are only as good as the people who operate and manage them and to add further value without procurement, people must be re-introduced back into the operation. Through TPM (Total Productive Mining), that is what RJB have set out to do.

Jan 1, 2001

By Jesus P. Manzano

The report of which this paper is a summary was made in 1890 for the Compania Investigadora Mexicana y Americana. Since the region examined covers 900 sq. kilom., chiefly of wooded arid rocky hills, almost without roads, and for the most part uninhabited, While the examination had to be made in two months, of which period more than 15 days were continuously rainy, I need not say that this account is not complete and thorough. I. Geography and Topography. The center of this zone, 19 kilom. SW. of San Luis Potosi, is situated in lat. 21° 24' N., and long. 2° 3' W. of Mexico City. The altitude ranges from 1866 m. (that of San Luis) to . 2816 m. (that of the Realito mountain), in the Sierra de Sail Luis. The topography is hilly—partly wooded, partly bare. The principal more level areas are the Bledos valley on the south, and portions of the haciendas of Tepetates, San Fran cisco and Santiago, on the west. The water-supply is scanty. The two streams that cross the Zone, the Santiago and Bledos rivers, carry water nearly the year through, though much reduced in the dry season. Other streams are torrents of less importance. All the waters of the valley and Sierra of Sail Luis arc absorbed or sink, not passing beyond Soledad de los Ranchos. The Continental di vide is within the Zone, some waters going west to the Pacific, others east to the Gulf of Mexico. II. Geology. Concerning the geology of this district I condense the fol lowing from the memoir, Las Minas de Guanajuato, prepared for the Minister of Fomento by Senor Pedro Lopez Monroy, mining engineer, with which I am entirely in accord. He says, ill substance:

Jan 1, 1902

Wetting Characteristics of Mineral Surfaces - Contact Angle Measurements through Molecular Dynamics Simulations

Sep 13, 2010