Search Documents

By Frederick H. Raab

A power-line proximity-warning (PLPW) system must have a high probability of detection (alarm activation at a specific distance), low probability of false alarm, and minimal set-up and maintenance. Tests of electric-field sensors have not demonstrated a dependable alarm distance. Alternative sensing methods such as microwave radar, optical radar, and sonar can meet the requirements by direct measurement of the range from the boom to the power line. Suitable microwave techniques include RF pulse, chirp FM/CW, and baseband pulse. Baseband-pulse radar has adequate range capability and does not require expensive microwave components. The radar cross section of a power-transmission cable is adequate for its detection optical-radar systems based upon LEDs and photodiodes are inexpensive, but can achieve only marginal performance in this application because of their limited modulation bandwidth. Since laser diodes and cryogenically cooled photosensors must be used to achieve the desired range resolution, the cost of an optical-radar system is greater than that of a microwave radar system. Sonar systems are feasible, but are not as precise and cost at least as much as baseband-pulse-radar systems. The performance of both optical-radar and sonar systems is degraded by dirt, necessitating the inclusion of a "windshield wiper.' Baseband radar appears well suited to the PLPW application. The cost of a baseband-pulse radar PLPW system is expected to be comparable to that of an electric-field PLPW system. Development and testing of an experimental model are therefore recommended.

Jan 1, 1982

One of the most significant problems experienced in land reclamation work has been the tendency of earthmovers to over-compact the subsoils and topsoils. The need for extensive subsoil drainage, because of over-compaction, becomes a very expensive exercise and can be attributed to poor planning. The problem has been addressed both at the Waihi and Huntly open-cast mines through the use of low ground pressure machines in the placement of subsoils and contouring. The use of subsoilers working to contour to aerate the soils is essential to integrate both the sub and topsoils so that significant root growth and drainage is established. Waihi's rainfall (approximately 200 mm annually) and light soils create difficulties in preparing for the final seed bed. A noticeable factor in preparation of the growing medium was the reaction of the lime particularly in the subsoils (damp), from a lumpy, quite heavy texture to almost a seed-bed texture within a period of approximately 72 hours. Also the high incidence of stone and debris which was not apparent in the placement of subsoils meant the job became very labour intensive. This will be overcome with the importation of a machine from the USA. All of the rubber tyred tractors used on these projects are four wheel drive in the 6S-aOhp range which for weight distribution and the safety factors allows for good landscaping techniques. Good engineering practices should ensure that slopes of no more than 3:1 be designed, keeping in mind that the long term planning must allow for maintenance and stock management of restored land.  In the preparation of the final growing medium the equipment used included: Caterpillar 05 LPG and blade; three-four wheel drive rubber tyre tractors; Super flow subsoiler; hydraulic twin spinner manure spreader; discs û two types; harrows; MF Seeder; Cambridge Roller and Duncan Rotatiller.

Jan 1, 1991

By Nicolas Denies, Gust Van Lysebetten, Bart Lameire, Jan Maertens, André Vervoort, Noël Huybrechts, Flor De Cock

"Abstract Originally developed for ground improvement works, the deep mixing method (DMM) has increasingly been applied in recent years for the realization of soil and water retaining structures and as alternative to traditional foundation solutions. From practice, there is a real need for practical guidelines dealing with the execution, the design and the control of such applications. With the aim of developing such guidelines, the BBRI ‘Soil Mix’ project was initiated in 2009. Within this research project, deep soil mix (DSM) material from 38 Belgian construction sites has been tested. In spite of the large advances in the mechanical characterization of the DSM material, one major issue remains the representativeness of the typical core samples in comparison with the real scale behavior of the soil mix elements. There is among others the question of the influence of the unmixed soft soil inclusions on this behavior and the issue of the scale effect which must be considered in the design. In order to investigate these questions, 8 large scale UCS tests and 17 large scale bending tests have been performed on excavated soil mix elements. The present paper discusses results of this experimental campaign, presents some research perspectives and highlights different aspects related to the design of soil mix elements for the realization of retaining wall or foundation solution.INTRODUCTIONSince several decennia, the deep mixing method (DMM) has been used to improve the strength and deformation characteristics of weak soils. In recent years, deep mixing has increasingly been applied – in Belgium and in other countries – for the realization of soil and water retaining structures and alternative foundation concepts. With regard to the execution of the DMM, one can refer to the European standard EN 14679 on deep mixing (2005) that was elaborated under the umbrella of CEN TC 288 “Execution of special geotechnical works”. However, from practice, it has been experienced that this execution standard does not provide enough pragmatic information and guidelines, in particular for the more recent applications of the deep mixing method (with retaining and bearing functions). The same need by the sector for guidance rules linked to design aspects in the context of Eurocode 7 was experienced as well. With the aim of developing such guidelines and in order to provide feedback to the European standardization platforms, the Belgian Building Research Institute (BBRI) has initiated the BBRI ‘Soil Mix’ project (2009-2013) in collaboration with the KU Leuven and the Belgian Association of Foundation Contractors (ABEF), the Belgian branch of the EFFC. Within this research project, deep soil mix (DSM) material from 38 Belgian construction sites, with various soil conditions and for different execution processes (CVR C-mix®, TSM and CSM), has been tested (Denies et al., 2012)."

Jan 1, 2014

By M. Veiga, L. Lavkulich, R. Pakalnis, M. Ghomshei, S. Baldwin, J. A. Meech

"On July 26, 2000, the Canada Foundation for Innovation announced an award of $1.3 M dollars for The Centre for Environmental Research in Minerals, Metals and Materials, CERM3, at The University of British Columbia. Additional funding was also provided by the British Columbia Knowledge Development Fund ($1.3 M) and the UBC Stewart Blusson Fund ($0.7 M). Annual industrial grants and contracts are providing support funding for the on-going research projects. Corporate membership in CERM3 entitles each participant to a seat on the technical advisory committee (TAC) as well as access to the five laboratory facilities currently under construction. Both the federal and provincial governments will also participate in the TAC through NRCan-CANMET and the BC Ministry of Energy and Mines, respectively. CERM3’s mission is:• to develop innovative methods to deal with environmental problems created by mining activity;• to promote sustainable development as a hallmark of management decision-making; • to produce mining and processing engineers with the required environmental skills; and• to enhance the image of mining in society as a vibrant and necessary component of a modern economy and society which disturbs the environment for the benefit of mankind.CERM3 brings together a multi-disciplinary team of researchers from over 12 departments at The University of British Columbia (UBC) to work on mining-related environmental problems. These include: chemistry; soil sciences; chemical and biological engineering; earth and ocean sciences; microbiology; civil engineering; electrical engineering; metals and materials engineering; mechanical engineering; mining and mineral processing, the Westwater Research Centre; the Institute for Resources and the Environment; and the School of Occupational and Environmental Hygiene. The centre intends to interact with scientists from industry, governments and other universities across Canada and around the world. CERM3 aims to become Canada’s leading environmental research facility for the mining industry. This paper describes the evolution of CERM3 and its coordinated multi-disciplinary approach to mining and the environment. Some of CERM3’s research projects include:• developing new protocols for environmental analyses to provide consistent and reliable assays;• isolating a natural virus for Thiobacillus ferrooxidans and other bacteria responsible for acid rock drainage (ARD);• designing bio-remediation and adsorption techniques for mine effluents;• promoting and enhancing the use of hydrometallurgy to reduce environmental pollution;• examining new approaches to comminution to decrease energy consumption;• developing a magnetically levitated hoisting system to reduce the footprint of a mine operation;• building a state-of-the-art supercomputer network laboratory for mine/mill simulations; and• designing intelligent bulkheads to seal tunnels following mine closure to survive for 1000 years.This latter project involves the establishment of a research station at the Britannia mine site, 45 km north of Vancouver, which will provide a full-scale facility to design the “Millennium Plug” and contribute directly to the solution to one of North America’s worst ARD-contaminated sites."

Jan 1, 2003

By Samuel M. Bryant

The purpose of this study was to develop procedures to measure Bingham flow properties for mine tailings and to use these to predict the possible consequences of a hypothetical tailings flow failure at the Tenmile Tailings Pond at Climax, Colorado. The consequences of such a failure were found to be minimal, and the failure itself highly; unlikely. Values of Ty (Bingham yield shear strength) and np (plastic viscosity) were measured for 10 materials using results obtained from vaned coaxial viscometer tests and triaxial tests.

Jan 1, 1983

By S. Bellec

A leaching model for gold ore that takes into account the impact of cyanide and oxygen concentrations as well as gold surface exposure on leaching performance is developed. Cyanide consumption is estimated by an empirical model that is a function of ore particles size distribution as well as cyanide, copper and sulphur concentrations. The proposed model has been validated by data from laboratory leaching tests on the Sleeping Giant gold mine ore. Keywords: gold leaching, modelling, exposure surface.

Jan 1, 2009

By Dejan Petrović, Pavle Stojković, Jelena Ivaz, Saša Stojadinović

In spite of the fact that flyrock phenomenon represents the real threat for personnel and machinery, it still remains insufficiently investigated. There are efforts, in the mining community, to explain the causes of flyrock, but the models capable to accurately predict flyrock occurrence and define the flyrock distance still do not exist. This article is an attempt to establish such a predictive model. The model utilized the adaptive nature of artificial neural networks and combined it with the accuracy of numerical modeling of physical phenomena. Necessary data were collected by high-speed camera recordings of actual blasts at three different surface mines and processed for further use for artificial network training. The result was a neuro-numerical couple which was capable to predict flyrock occurrence, estimate the launch velocity of flyrock fragments, and calculate the maximum distance of flyrock fragments. The safe distance was then calculated by multiplying the flyrock distance with a factor of safety. The article explains the procedure for data acquisition and processing, artificial network construction, training, and validation. It also explains the principles of flyrock distance calculation and, finally, provides a definition of factor of safety and safe distance. The results showed that the prediction was satisfactorily accurate and reliable.

Oct 22, 2021

By D. Washington

The US economy and the demand for nonfuel minerals grew at lower rates in 1995 than in 1994. Demand for major metals, such as aluminum, copper and steel, was mixed but relatively stable. The building industry, including highway construction, helped to support modest overall growth in demand for industrial minerals. The value of processed materials of nonfuel mineral origin produced in the United States during 1995 was estimated to be $395 billion, an increase of almost 10%compared with 1994 (Fig. 1). The estimated value of US raw nonfuel minerals production during 1995 was $38billion, about 7% more than in 1994. The value of US minerals production has increased in 30 of the last 35years.

Jan 1, 1996

By K. J. Liles

Research was undertaken by the Bureau of Mines to determine the technical feasibility of producing lightweight aggregate from the waste glass fraction of municipal incinerator residues. Tests were conducted to determine the amount and optimum size of glass, the amount of sodium silicate, and the method used to form the material to be expanded. The most suitable mixture, 78 percent glass, 20 percent clay, and 2 percent sodium silicate, was pelletized and then expanded by exposure to a temperature of 1,550° F for 15 minutes The resulting lightweight material had a bulk density of 38 lb/cu ft and exhibited excellent pore structure. Concrete test cylinders made from the light weight aggregate had a unit weight of 104 lb/cu ft and a compressive strength of 2,550 lb/sq in after a 28-day steam cure.

Jan 1, 1976

By Fred S. Karn

Inhibitors are used in coal mines as a precaution against accidental dust explosions. Although rock dust is the usual inhibitor many others have been tested. To facilitate testing a screening process using laser irradiation was proposed. The procedure includes irradiation of a coal-dust mixture followed by mass-spectrometric analysis of the evolved gases and an evaluation of the flammability characteristics of the gases. Carbonate-type inhibitors decreased the percentage of combustibles in the gases generated and inhibitors like NaCI (thermally stable salts) decreased the total gas generated. A suitable test procedure did not result from the investigation, demonstrating the inadequacy of fast heating, non-combustive techniques in rating inhibitors of coal dust explosions.

Jan 1, 1973

By D. M. Muir

Thiosulfate offers a non-toxic alternative to cyanide for processing gold ores. The mechanism of leaching gold using ammoniacal thiosulfate solution is driven by the Cu(II)-Cu(I) redox couple and is complicated by competing ligands such as NH3 and S2O32-. It is shown that an understanding of the copper speciation and sulfur speciation is required to optimise this system. This paper presents Eh-pH and speciation diagrams for varying concentrations of Cu(II), S2O32- and NH3 and discusses the conditions under which various copper and sulfur species are stable.

Jan 1, 2001

By Douglas Bartley, Jay Elkin

The state of Pennsylvania was at one time one of the leading coal producing states in the east. However, legislation and industry trends over the last 10 years have adversely affected the amount of bituminous coal mined in Pennsylvania and the whole eastern United States. The application for and approval of a new mining permit is a very costly and arduous task. When a new mining operation is established it is crucial that nothing within the operator’s control causes the operation to stop producing. This paper discusses the action taken by a small mine in Pennsylvania when their blast induced vibrations rose to levels that typically would have resulted in a total mine shut down by the regulatory body governing such operations.

Jan 1, 2003

By Paolo Bevilacqua, Paolo Antonini, Lorenzo De Lorenzi

"Italy is one of the major producers of ceramics in the world. Ceramic production requires large quantities of K-feldspar, which is commonly sourced from granites, alkali-granites, and “granitic” sands. These rocks contain other minerals, such as quartz, plagioclase and mafic minerals, which are undesirable for ceramic production. Due to the coarse mineral grains that constitute these rocks, a reasonable liberation is achieved at a relatively coarse grind size.This paper reports a study conducted on the separation of K-feldspar from quartz, plagioclase and biotite, from a feed of ground granite. The feasibility of the separation using a dynamic dense medium separation system has been investigated, as an alternative to the traditional flotation technique. The use of a two stages cylindrical vessel (Tri-Flo) was preferred to a conical vessel, due to the improved separation efficiency. Tests were conducted on two samples of crushed granite having size distributions of –3 +1 mm and –1 +0.5 mm.Heavy liquid analysis was performed on the two samples. As the rheological properties of the dense medium interact with the separation efficiency, the stability and viscosity of the dense medium were controlled and kept within an appropriate range; which was achieved with the addition of an artificial contaminant (clay) to the dense medium."

Jan 1, 2003

By V. Labiouse, P. K. Kaiser, F. Descoeudres, F. Rojat

In this paper some failure phenomena observed in the crossing of brittle rock formations at the Lötschberg base tunnel are presented. A brittle failure criteria, recently developed by Canadian researchers, is applied through finite element calculations together with a semi-empirical failure criterion, to explain these behaviours. Good agreement is found between predicted and observed failures at the tunnel walls. This study also shows some of the limitations of this approach. Dans cet article sont présentés certains phénomènes de rupture observés durant la traversée de zones de roches fragiles lors de l’excavation du tunnel du Lötschberg. Un critère de rupture développé récemment par la recherche canadienne est utilisé à travers des calculs par éléments finis. En parallèle, les résultats sont comparés avec ceux d’un critère semi-empirique. Au niveau des parements, l’ampleur des ruptures observées est assez proche des résultats de calcul. Cette étude a également permis de mettre en avant certaines limites de l’approche choisie. In diesem Artikel werden verschiedene Brucharten dargestellt, die bei der Durchfahrung von sprödem Gestein im Rahmen des Ausbaus des Lötschberg-Basistunnels beobachtet wurden. Zur Erklärung des vorliegenden Verhaltens wurden die erst kürzlich in Kanada entwickelten Theorien zur Beschreibung von Sprödbrüchen herangezogen und bei der Berechnung mittels der Finite-Elemente-Methode und eines semi-empirischen Kriteriums angewendet. Die so vorhergesagten Versagenszonen an den Tunnelwänden stimmen mit den Beobachtungen gut überein. Die Studie hat auch dazu beigetragen, die bei der Anwendung des Lösungsansatzes angetroffenen Schwierigkeiten aufzuzeigen.

Jan 1, 2003

By J. E. Sepulveda, R. Morrow

"The Linear Wear Theory provides a reliable framework for the assessment of grinding media performance at full scale. This theory can be applied for analyzing grinding media consumption rates in any given grinding operation as well as the evaluation of alternative grinding media products, based on actual operational data, correcting for conditions like ore hardness, feed and product sizes, mill power and circuit throughput; all of them unrelated to the grinding media intrinsic quality attributes. A series of Moly-Cop Tools 3.0 applications have been developed to facilitate the calculations involved. Moly-Cop Tools 3.0 is available, free of charge, to all interested parties through the corresponding author.INTRODUCTION Mineral grinding circuit operators recognize the significance of grinding media (balls) consumption on the cost structure of any full scale grinding facility. The effective cost associated with this essential consumable depends on two factors: delivered price and durability (quality) of the grinding media. When evaluating alternative grinding media varieties, there is a well accepted evaluation criterion by which a given media type is considered to be “cost-effective” when its unit application cost – normally expressed in $/ton of ore ground – is shown to be lower than that of a nominal reference condition: Grinding Media Cost = Ball Price x Ball Consumption (1) ($ /ton ground) ($/ton balls) (ton balls/ton ground) Under this criterion, an alternative, higher-price grinding media product could be “cost-effective” if its associated consumption rate is sufficiently lower than the reference media, enough to yield a lower grinding cost, as dictated by Equation 1. For the proper application of the above criterion, evaluators must rely on representative indicators of grinding media quality, ideally independent of most mill operating conditions. In each particular case, ball price is always a known component; however, it is not so evident how media performance (quality) differences amongst alternative product types could be assessed with a reasonable degree of accuracy and precision."

Jan 1, 2014

By Frank E. Chase

Clay veins, also referred to as clay elastic dikes, have been responsible for numerous underground injuries and fatalities. These hazardous structures are also responsible for increased production costs during all phases of mining. For these reasons, the Bureau of Nines has investigated the physical characteristics of and roof instability problems associated with clay veins in order to make support and other mining recommendations. In addition the occurrence and origins of clay veins were examined to determine whether or not the structures could be projected into unmined portions of the coalbed. This investigation included portions of the Arkoma, Illinois, Northern Appalachian, Southern Appalachian, and Uarrior Coal Basins. Virtually a11 clay veins observed or documented occurred in the Illinois and Northern Appalachian Basins. Observed clay veins ranged in sire from 1 inch to 16 feet In cross-section and were found under shale, siltstone, sandstone, and limestone roof rock. Individual clay veins were predominantly composed of claystone; however, limestone. siltstone. and sandstone infilled clay veins do occur. Clay vein formation has been associated with the infilling of fissures which result from compressive, tensile, or shear ground failures. These gaping fissures were propagated by compactional processes and/or tectonic stresses active during and subsequent to coal iff cation. Associated fault, fracture, and slickenside planes commonly parallel clay veins and disrupt the lateral continuity of the immediate and, sometimes, main roof. When clay veins parallel or subparallel the direction of face advance the roof is segmented into cantilever beams causing unstable conditions. Therefore, the strata on either side of the clay vein must be bolted and strapped together to form a beam.

Jan 1, 1984

By Wm. Mark Hart

High horizontal stresses and shear failure have been considered the major reasons that cause entry roof failure and falls for underground mining. Therefore, reorientation of the current mining systems or layouts or using angular crosscuts in mains or gate entries becomes more popular if a greater than normal horizontal stress is measured. However, reorientation of the current mining systems or layouts is always expensive and use of the angular crosscuts may weaken the pillar structure at corners. Therefore, cautions must be taken before any decision related to reorientation of the current mining systems or layouts or use of angular crosscuts is going to be made. In order to prevent entry roof failure and falls, the following two issues must be carefully examined and fully understood: 1. Which one, shear stress or tensile stress, is going to be blamed for entry roof failure? 2. Which one, horizontal stress, vertical stress, or local geological weakness plays a major role in entry roof failure and falls? This paper analyzes the mechanisms of entry roof failure and falls for underground mining in general examines the roof fall history at Springvale Colliery, and proposes the means of preventing roof failure and controlling roof falls for Spingvale Colliery in particular.

Jan 1, 1996

By Clark F. Grain

These investigations were undertaken as part of the Bureau of Mines program for the development and evaluation of high temperature nonmetallic materials. This report consists of thermal expansion and phase inversion measurements by high-temperature X-ray diffractometry on the principal oxides of beryllium (BeO), calcium (CaO), titanium (TiO2 ), zirconium (ZrO2 ), hafnium (HfO2), and thorium (ThO2); all were high-purity commercially available oxides. Thermal expansion values were calculated from unit cell dimensions measured at selected temperatures. Expansion was determined parallel to each major crystallographic axis for the anisotropic oxides: BeO, TOi2, ZrC2, and HfO2. Combined random and systematic errors in the thermal expansion values are considered to be less than 3 percent of the total expansion at 500° C. and approximately 2 percent at 1,000° C. No hysteresis in the expansion curves was noted between heating and cooling cycles. The Bureau's values were compared with published expansion measurements obtained by X-ray diffraction, dilatometric, interferometric, and telemicroscopic techniques. For anisotropic oxides, average linear expansion values were calculated from the volume expansion.

Jan 1, 1962

Jan 1, 1970

Technically competent, skilled and efficient people are often promoted into management and leadership positions, climbing through the ranks to senior positions without training or direction in soft skilling. These soft skills are what really motivate teams to achieve business goals. This paper looks at the three key soft skill areas that compel teams to follow leaders, namely manners, mentoring and motivation. Our manners control our behaviour and attitudes and operate at a subconscious level. The manners that æmaketh the manager worth followingÆ are discussed with the express purpose of bringing these to our consciousness. When we recognise those behaviours that alienate or inspire we can consciously behave in ways to lead our teams towards our goals. Our attitude to mentoring and developing people around us speaks of our commitment to our people and our industry. Surprisingly, the more we give the more we get. Mentoring gives us an opportunity to leave a legacy, inspire commitment and build support within the mining community. How do we as managers provide mentoring within our teams? What are the mentoring behaviours that inspire learning and commitment to a managerÆs goals? When managers can identify an individualÆs unique mix of motivational drivers, they can understand how to motivate them. And motivated people are more likely to be retained and work towards the managerÆs goals. The soft skills used to understand and motivate within the three core motivation drivers (competence, expression and treatment) are presented. This paper is designed to share straightforward soft skills for managers who have tread the technical route.

Jan 1, 2006