Search Documents

By P. Desclaux, A. Gosselin

"In 1999, PFC measurements were carried out at Alcan smelters as part of a large measurement campaign led by the Canadian Aluminium Association. Side worked prebake (SWPB) and horizontal stud Söderberg (HSS) plants in Arvida were the selected sites. CF4 and C2F6 emissions were measured continuously in the exhaust duct and at the roof vents for a week. In parallel, voltages from four designated cells were recorded at a high scan rate. Results were analyzed and correlations between voltage, anode effect duration and PFC emissions were tested. Some fundamental anode effect mechanisms were proposed and validated with the observations. IntroductionFollowing the international agreement reached within the scope of the Kyoto protocol, voluntary partnerships have been established in many countries especially for the aluminum industry. It is well known that the PFCs that are periodically emitted during aluminum production are the major source of fluorocarbon emissions. The latter are part of the greenhouse gases. In the fall of 1999, Alcan announced that it will adopt, promote and regularly renew a long-term greenhouse gas management commitment at all of its facilities within the framework of the so-called TARGET program that was implemented during 2001. The program is intended to produce on-going reductions, which will be reported publicly on an annual basis.Improvements in the understanding of the mechanisms leading to PFC emissions will contribute to targeting the most appropriate reduction actions. PFC measurement campaigns have been driven toward this end. The first measurement campaign was conducted in 1993 in order to get a picture of the emissions and a base line. The last measurement campaign was conducted in 1999 and its main objective was to compare current emissions with those measured in 1993 and to confirm the accuracy of the predictive equations for the calculation of PFC emissions. This campaign has been conducted by the Canadian Aluminium Association and measurements were made in plants using different technologies. Results of this campaign have already been reported by Bouchard et al. (2001)."

Jan 1, 2002

By R. A. Ynchausti

In January 1993, Pyramid Resources began implementation of a supervisory expert control system at a U.S Cu concentrator. The objective of this control system was to improve plant profitability through unit operation optimization and integration. This paper documents the key aspects of the project, including: economic and associated benefits, system architecture, concepts of implementation, process control strategies, practical aspects of implementation and conclusions. The implementation of expert control at this concentrator has resulted in an estimated benefit of $50,500 per day. This is a net result of improved tonnage, reduced reagent consumption, improved concentrate grade and reduced energy per ton produced.

Jan 1, 1995

By Seong- Rin Lim

Light-emitting diodes (LEDs) are regarded as environmentally friendly light sources due to their high energy efficiency and lack of mercury content. LEDs are used for a variety of domestic and commercial lighting systems, where they are replacing incandescent and fluorescent lamps at a rapid rate. Incandescent lamps inefficiently consume energy because electricity is mostly converted to heat rather than light. This causes unnecessary environmental impacts and energy consumption associated with power generation and transmission from a life cycle perspective. Although fluorescent lamps are more energy-efficient than incandescent lamps, their disposal at end-of-life presents special challenges because of the presence of toxic mercury. Despite the seemingly apparent advantages of LED, very few studies have rigorously addressed potential environmental consequences of their disposal. Specifically, LEDs are designed with III-V semiconductors that presumably consist of toxic and rare materials, including arsenic, gallium, and indium. We hypothesize that, depending on their concentrations and leachability, these constituents may also contribute to render LEDs as hazardous waste at the end of their useful life.

Jan 1, 2010

By A. Bezama

For over a decade European countries have addressed contaminated sites by developing technologies for managing both polluted soil and groundwater. This development has not only been driven by health and environmental aspects, but also because of economic pressures, as the remediation and redevelopment of derelict areas can be a meaningful alternative to undeveloped areas for the establishment of new industrial, recreational, housing and service locations. In most developing countries, however, the subject of contaminated sites is a new environmental issue that authorities have recently started to deal with. Among these countries, Chile has just started to prepare the country's legal context as well as to foster the formation of research and investigation groups that will deal with the exploration, investigation and management of contaminated sites. That requires a comprehensive technical, scientific and legal support in this stage. Goal of this article is to present the state-of-the-art technologies for site remediation currently applied in industrialized countries, in order to identify the most interesting approaches that can be implemented within the Chilean situation, especially considering the influence of the copper mining industry on the soil and groundwater quality of the environment surrounding their production facilities.

Jan 1, 2007

By J E. Powalisz

Obtaining a representative sample of bulk materials in process industries is critical to providing valid data for process control and custody transfer (valuation). The accuracy of a sample, that is to say how well the sample represents the material in the process, is directly related to how well the process can be controlled and to how much a product may be worth. Sampling accuracy then is in fact related to bottom line profitability.Sampling theory offers information and equations on how to take a representative sample from a process, however, the actual practice of extracting a sample from the process can be more of an art.Key sampling variables include product specifications such as bulk density, particle distribution, material conveyance, practical sampler location, sampler type and sample frequency and volume/mass.This paper discusses basic sampling theory, sampling methods, types of samplers, how to develop a ‘real world’ sampling system and current manual and automated samplers.Key points include ‘practical precision and variance’, material properties, flow properties, direct sampling versus indirect sampling, sampler types and applications.CITATION:Powalisz, J E, 2014. Bulk solids sampling, in Proceedings Sampling 2014 , pp 179–188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By José L. M. Clemente, John R. Davie

"Abstract An extensive pre-production static and dynamic pile load testing program was conducted for a coal-fired power plant. The static load testing program included axial compression, uplift (tension), and lateral load tests. Three types of piles were tested: Monotube, closed-end pipe, and step-tapered. The load tests were used to (a) determine pile driveability characteristics for each pile, (b) verify pile load response behavior, and (c) provide data to support the selection of a cost-effective piled-foundation system for the plant. A recent publication (Clemente and Lewis, 2013) describes the compression load testing program, the interpretation of instrumentation measurement results, and pile selection criteria. This manuscript describes site subsurface and groundwater conditions and installation of probe piles for testing, focuses on the uplift and lateral load testing program, and provides a comparative interpretation of the load test results.INTRODUCTIONThe pre-production probe pile load testing program described here was conducted for a 202-megawatt, coal-fired power and steam generating (cogeneration) facility. A schematic layout of the main plant (power block area) is shown in Figure 1, which also includes the locations of clusters of preproduction probe piles and boreholes drilled near these clusters.The load testing program included 24 pre-production probe piles driven throughout the power block area. The probe piles were driven at locations T-1 through T-8, shown in Figure 1. Three types of piles were driven at each location: Monotube pile; closed end, straight shaft pipe pile; and step-tapered pile. At each location, the three piles were driven in a row with the pipe pile at the center, and the center-tocenter spacing between piles was equal to about 1.5 m (> 3.5 pile diameters for the largest pile). No pile cap was used to connect the three piles, and the three piles driven at locations T-1 through T-8 will be referred to as pile clusters. A complete suite of static load testing (compression, tension, and lateral) was performed on each individual pile at Cluster T-2 and on the step-tapered piles only at Cluster T-8, shown in Figure 1.Clemente and Lewis (2013) provide details of the compression load testing program, the interpretation of instrumentation measurement results, and pile selection criteria. This manuscript focuses on the uplift (tension) and lateral load testing program. A brief summary of the site geology and existing subsurface and groundwater conditions in the vicinity of the test pile clusters is presented, with emphasis on T-2 and T-8. Probe pile driving results at T-2 and T-8 are also presented. Descriptions of the static uplift and lateral load test program at T-2 and T-8 are given along with a comparative evaluation of the load test results."

Jan 1, 2014

By Manfred Jaeger, Klaus Ertmer, Walter Dietrich, Jochen Greinacher, Wilhelm J. Kogelmann

In Europe, novel low-cost excavator-mounted Multi Tool Miner (MTM) systems, consisting of cutter head, hammer, bucket and drill attachments permit one unit to perform multiple tasks replacing several purpose-built machines. At the Weser Tunnel in Germany, cross-passages between the twin tubes were excavated in frozen ground with a remote-controlled mini-excavator equipped with a quick-change cutter head, ripper tooth and bucket. In Switzerland at the N2 interstate near Basel, W. Dietrich AG enlarged a 2-lane tunnel to three lanes with a cutter head mounted on a special excavator. Blasting and heavy hammers were not permitted due to the closeness of the “live” twin tube. At the N20 Zurich bypass, the Joint Venture of Jaeger, Frutingerand AHB excavates highway tunnels, some with extremely large cross sections, conventionally. A cutter head mounted on an excavator removes the rock shattered by blasting precisely to the pay line, thus preserving the rock’s self-supporting capacity preventing subsidence and damages to water resources and buildings on the surface under low overburden.

Jan 1, 2003

By Sun Guangzhong, Liang Jinhuo

Adverse geological condition is a major factor which makes construction difficulty in tunneling. But if it is predicted and tunnel support is made efficiently in time, the above difficulty can be reduced. It is necessary to develop one or several effective and economical geological methods for prediction of tunnel geology while expensive and time-consuming instruments are used. This paper reviews and proposes several geological methods for prediction of fault, seam, contact zone, and groundwater inrush. These methods have been proved to be effective and economical in tunneling practice in China.

Jan 1, 1987

By James A. Curry

Table I identifies the maximum cost of the individual provisions with spoil disposal in Appalachia leading at $3.98 per ton, This was followed by deep mine subsidence control and monitoring at $1.66 per ton. At the request of the U.S. Department of Energy, the Bowser-Morner Testing Laboratories of Dayton, Ohio, evaluated Consol's cost estimates for 14 of the 21 regulatory provisions the company studied. It is interesting to note that Bowser-Morner concluded that Consol's estimates of costs were very conservative and that the actual costs will be substantially higher than what the company reported. In 1978 a joint committee of the National Coal Association and the American Mining Congress made estimates of cost impacts under 11 OSM permanent rules (see Table II). Six rules applied to mid-western strip mining were projected to cost $6.52 to $17.17 per ton. Five rules applied to mid-western strip mines showed costs ranging from $.91 to $6.11 per ton. Three rules applied to deep mines (regardless of region) were seen raising costs from $ .57 to $2.67 per ton. The joint committee reported trouble developing overall figures because member firms used widely different assumptions in calculating their costs. That same statement could no doubt be made when comparing most cost data available today.

Jan 1, 1980

By Duane L. Abata

This work, conducted under Bureau of Mines contract, deals with the development of a computer graphics software package that will: 1. display mine ventilation schematics and other representative Illustrations for a real-time data acquisition system under development by the Bureau, and, 2. utilize the Bureau-owned Minefire and Ventilation Code for display of ventilation on and contamination predictions. The software package has been written try operate on a 64K, Z-80 based microprocessor-computer. The project has been divided into two phases. The first phase dealt with the development of the graphics software The sec rind phase dealt with the retrofit of the Minefire and Ventilation Code to the Z-80 microprocessor-computer.

Jan 1, 1984

By Jeane Hull

Jan 1, 2009

By Edward L. McHugh

The Thousand Lakes Wilderness has no known economically significant mineral resources. However, the geologic setting of the Wilderness indicates a potential for the discovery of geothermal resources. INTRODUCTION The Thousand Lakes Wilderness occupies 16,335 acres (6,611 ha) in eastern Shasta County, California. A mineral resource study of the area was authorized by the Wilderness Act of 1964 (Public Law 88-577). Mining records and published information were examined, and field investigations conducted in 1979. The Wilderness is about 50 miles (80 km) east of Redding and 12 miles (19 km) south of Burney, California. It lies in the Cascade Range of California. Relief is more than 3,000 feet (910 m); elevation is greatest at the summit of Crater Peak, 8,677 feet (2,645 m).

Jan 1, 1982

By Theodore L. Turner, Joseph H. Swift

A study on a small laboratory scale was made of the use of ammoniacalammonium carbonate for batch leaching Mn from low- grade manganiferous materials ( 6 to 16 pct Mn) obtained from deposits in the southern district of Aroostook County , Maine . These materials were partially reduced at 500 ° to 700 ° C with H₂ or CO and then leached with solutions of NH and CO₂ dissolved in water . Extraction of 80 to 90 pct of the Mn was obtained from some sample materials , but 10 to 34 pct of the iron was also extracted . Material from the Littleton Ridge deposit contained manganese intimately associated with Fe , a condition which contributed to difficulties in obtaining a commercially acceptable product . Extensive investigations of the leach and reduction processes with various mixtures of H₂ and water vapor , and CO and CO₂ , failed to disclose a set of conditions for selectively leaching the manganese . Finely divided metallic Fe was probably produced during the reduction steps so that Fe was leached with the Mn in the subsequent extractions .

Jan 1, 1964

By Kurt Herzog

State-of-the-art automation information technology and connectivity enables the digitalization of steel production that goes far beyond conventional automation of industrial production. Initiatives have been started around the globe to foster digitalization like IIoT (Industrial Internet of Things) in the US, Industrie 4.0 in Germany or China 2025. Primetals Technologies is actively driving the digitalization shaping the future of steel production. Intelligent combination of sensor technology combined with digital models as well as quality and production planning and control systems leads to new dimensions in product quality and production cost reduction. New diagnostic ways allow intuitive fault tracing or processing to support faster maintenance. Digital assistants support both operation and maintenance using context-oriented or self-learned information.

Oct 30, 2017

By Carl E. Norman

An investigation of geologic structure on macroscopic, mesoscopic, and microscopic scales was conducted on near-surface igneous and metamorphic rocks in which the existing stress field was determined by in situ methods. A consistent NE-SW orientation of the maximum compressive stress in the horizontal plane at four of five test localities appears due to the intrusion of NW-trending diabase dikes. Structural features at the mesoscopic scale show no consistent directional relationship to determined stress directions. Petrofabric diagrams of open microfractures show preferred orientations, but these are not consistently related to the orientations of larger structural features, such as joints, foliation, or mineralized shear zones. However, at five of six test sites the preferred direction of microfractures occurs nearly perpendicular to the maximum principal stress directions; an anomalous parallel relationship exists at a test site in an intrusive rock body. The results suggest that the open microfracture subfabric may provide a means for gaining information on the directional properties of stress fields. Such information can be obtained from oriented cores taken from holes which exceed the approximate 100-foot depth to which other in situ methods are presently limited.

Jan 1, 1970

By W. C. Whittaker

COMPLETED in November, 1943, at a cost of over $1,500,000, Elk River colliery of the Crow's Nest Pass Coal Company, Limited, has been laid out and equipped for an ultimate annual production of 1,000,000 tons and replaces the recently closed Coal Creek plant, which has been operated by the Company for the past forty-five years. The project has involved the opening of mines in three seams, the construction of a complete set of colliery buildings, including a modern preparation plant of 360 tons per hour capacity, and the laying out of the necessary yard tracks and spur connecting the new development with the Company-owned Morrissey, Fernie and Michel railway, which, in turn, connects with the Canadian Pacific railway at Fernie. The colliery is three and a half miles east of Fernie, B.C., near the southern end of the Crow's Nest coal field, which contains the largest and most important body of coal in the Province of British Columbia. The coal-bearing horizon is the Kootenay formation, present in the form of a syncline covering an area of 230 square miles. Most of the coal seams occur in the lower 2,000 feet of the formation, the covering beds being largely coarse sandstones and conglomerates of great thickness, the presence of which accounts largely for the preservation of the coal measures. James McEvoy, in the report of the Geological Survey of Canada for the year 1900, states that the basin appears to contain a fairly constant coal content of nearly 172 feet in 23 seams of a thickness of one foot or over. Coal has been mined in the Fernie district since 1897 and the first shipments were made from Coal Creek colliery in the following year, over the then newly constructed British Columbia Southern railway. Since that time, a total of over 16,000,000 tons of coal has been produced, an average of 350,000 tons per year. The7ears of peak production were 1910, 1912, and 1913, with an all-time high of 924,000 tons in 1913. The lowest output in the history of Coal Creek was that for the year 1933, when only 60,340 tons were produced, the colliery being closed for some months. Present production from Elk River colliery averages 1,150 tons per day, the output being considerably less than it could be were sufficient man-power available.

Jan 1, 1944

By X Hill

Throughout the 2016/2017 financial year, the NSW Resources Regulator conducted an assessment of each underground metalliferous operation across the state to assess how each operation managed the principal mining hazard of ground and strata control. The assessment considered all aspects of the mining process, including all aspects of managing geotechnical risk within drawpoints. This assessment is ongoing and, therefore, this paper is limited to the first six mines assessed in the program.In 2015 there were three fatalities in and around underground drawpoints in Australian metalliferous mines. Whilst many of the systems of work around underground development are consistent across the industry, there are large discrepancies around how each underground mining operation manage the risks associated with drawpoints.For drawpoints to be effectively managed, their management needs to be considered at the earliest stages of the mine planning process. By using downholes and adopting remote systems of work – systems that are continuing to improve with technology – the risks drawpoints posed can be greatly reduced.The assessment by the NSW Resources Regulator revealed a number of common failings across the state in the management of the risks that drawpoints pose. The assessment also observed a number of innovative practices that particular operations have adopted in the wake of serious incidents occurring within drawpoints at their operation; however, these practices have not been communicated to other operations.It is hoped the learnings from the assessment can be considered by industry and reduce the risks drawpoints pose in underground metalliferous mines.CITATION:Hill, X, 2017. Learnings from review of drawpoint management across New South Wales mines, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 143–150 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By E Bouchard March, F Lavoie, B Legare, K Bourassa

Quebec Iron Ore (QIO), a subsidiary of Champion Iron Limited (Champion), completed the restart of the Bloom Lake iron ore mine located in the heart of the Labrador Trough region of Northern Quebec, Canada in February 2018. Prior to its restart, the concentrator flow sheet underwent major upgrades which brought the iron recovery to the highest of all Labrador Trough operations. After two profitable years of production, QIO, supported by Soutex, started to look at technologies to improve its current performance and integrate into its expansion project flow sheet. From the lessons learned while optimising Phase 1, the addition of a scavenger-cleaner processing stage was identified as an improvement opportunity to increase recovery, produce a higher-grade product, and further improve the stability of concentrate quality. In 2019, the NI-43101 feasibility study for the Phase 2 expansion, aiming to double the production of high-grade iron ore concentrate, was published. Based on the metallurgical test work, the hydraulic classifier was selected to perform the scavenger-cleaning duty for its well-established performance and known behaviour at the cleaning step in the Phase 1 plant. To validate laboratory results, a pilot scavenger-cleaning hydraulic classifier was installed in Phase 1. Although the hydraulic classifier was selected for the feasibility study, metallurgical test work performed with the REFLUX® classifier showed interesting potential. It was thus decided to also install a pilot RC300 Reflux classifier at the scavenger-cleaning stage in Phase 1. Despite their apparent great similarities, the metallurgical performance was significantly different, and many dozens of sampling campaigns highlighted the different performance of both pieces of equipment considering the feed material particle size. This article presents the pilot plant results in terms of recovery, selectivity and stability for both the Reflux classifier and the hydraulic classifier operated in a scavenger-cleaner stage at the Bloom Lake iron ore concentrator.

Nov 8, 2021

By Iman G. Ghanad

El presente texto describe un nuevo método para el tratamiento de concentrados de cobre con alto contenido de arsénico utilizando el carbón activado como catalizador. Para ello, se realizaron pruebas de lixiviación con concentrados de enargita de tres minas de Chile, Perú y Estados Unidos, donde los resultados señalaron que la disolución de la enargita fue más rápido con la influencia del carbón en la solución lixiviante, incluso después de haber reciclado el carbón.

Sep 12, 2011

By L. Tong, D. Robinson

"The stirred milling of nickel laterites offers possibilities for improving liberation and selective size reduction of soft nickel-bearing minerals in laterites. Batch grinding tests were performed in a netzsch™ lME4 stirred mill on siliceous goethitic, goethitic, and saprolitic nickel laterites. Tests on the -2,000 µm sample displayed the effects of selective comminution. The -38 µm product of grinding the -2,000/+38 µm feed confirmed the effects of selective grinding and nickel upgrading. Size classification followed by stirred milling is recommended for nickel upgrading. The energy requirement in the stirred milling was also investigated.RÉSUMÉ le broyage par billes de latérites comportant du nickel offre des possibilités d’amélioration de la libération et de la réduction sélective de la taille des minéraux nickélifères tendres dans les latérites. Des essais de broyage en vrac ont été effectués dans un broyeur à billes netzschMD lME4 sur des latérites nickélifères à goethite siliceuse, à goethite et saprolitiques. Des essais sur l’échantillon -2000 µm présentaient des effets d’une comminution sélective. le produit -38 µm de l’alimentation -2000/+38 µm confirme les effets d’un broyage sélectif et du rehaussement de la teneur en nickel. Pour améliorer la teneur en nickel, il est recommandé de classifier le minerai en fonction de sa granulométrie, puis d’effectuer un broyage à billes. l’énergie requise pour le broyage à billes a aussi été étudié."

Jan 1, 2015