Search Documents

By O. O. Laudig

It is a well-established fact that some ores do not reduce as readily in the furnace as others, thus seriously affecting out-put, and consequently, cost of product. With the object of obtain ing some information upon this subject, the following experi ments were made in the laboratory of the Buffalo Furnace Company. Efforts were made to obtain, as nearly as possible, represent ative ores from some of the most important mining districts in the United States. The ores received were from the Mesabi, Marquette, Gogebic, Menominee and Vermilion ranges of the Lake Superior district and from Southwest Virginia. Requests

Jan 1, 1897

By J. B. Shannon, J. D. Grenia

The Buick Mine is a joint venture of American Metals Climax, Inc. and Homestake Mining Company located 120 miles by road southwest of St. Louis, near the village of Boss, in the `New Missouri Lead Belt'. Since start-up in 1969, over four million tons of lead-zinc ore have been mined and milled at Buick. Situated 1100 ft below the surface at an elevation 270 ft above sea level, the flat lying sinuous orebodies are up to 250 ft wide, 85 ft high and several thousand feet long. Mineralization is galena, sphalerite and chalcopyrite in dolomite.

Jan 7, 1973

Native asphalt was produced by five companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by White Uvalde Mines and by Azrock Industries Inc., Uvalde County, TX. Gilsonite, a solidified hydrocarbon, found only in Utah and Colorado, was mined by American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California), by Ziegler Chemical and Mineral Corp., and by Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation) from properties in Uintah County, UT.

Jan 1, 1984

The search for an efficient and economic machine to excavate hard rock continues. Development of the Robbins Mobile Miner commenced in 1983 with the formation of a joint venture between Mount Isa Mines Limited and The Robbins Company. Construction of the machine ensued and preliminary trials to verify the cutting action were undertaken in the USA prior to transportation to and assembly at Mount I-sa where mining commenced in September 1984. Initially, the machine was used to develop the S60 Decline which serves as a combined access and conveyor drive for the Southern 1100 Orebody Ore Handling System.

Jan 1, 1988

By Carlo Massa

The Societâ Anonima di Miniere e di Alti Fòrni, familiarly known as the " Elba Company," works the rich ore-deposits of the Island of Elba under a long-term contract with the Italian Government. The ore-deposits are scattered over the eastern and southeastern coast; but as these parts of the island are not well provided with ports, the blast-furnaces were built at Porto-ferraio, the principal town of the island, situated on the northern shore, and possessing a magnificent natural harbor where vessels even as large as the battleships of the Italian navy can comfortably anchor. In the selection of Portoferraio the cost of transporting the iron-ore from the different mines to the blast-furnaces has been reduced to a minimum, and shelter has been provided for the company's flotilla of tugs and barges, as well as for the steamers carrjing coal and pig-iron. The whole plant, of which a general view is given in Fig. 1, comprises: 1. A discharging-pier with unloading-cranes. The ore and coal are transported from this pier by means of an aerial cable-railway to the coal- and ore-storage yards. This cable-railway is supported by an iron bridge extending from the pier to the shore and by a wooden trestle extending from the shore to the yards. 2. Blast-furnaces, two in number, with all the accessory apparatus, such as blowing-engines, dry purifiers, Cowper hot-blast stoves, hoists, etc. 3. Coke-ovens, two batteries, with coal-bin, crushers and boilers. 4. Engine-house containing the blast-engines and the electric generating-station. 5. Pumping-plant. 6. Narrow-gauge railways.

Jan 1, 1905

The development of Mount Isa Mines Limited power supply is traced through the history of the mine operations. As would be expected, growth of the power supply system follows closely the increase in mine output, although it will be seen that total kWh. produced per ton milled shows a considerable reduction in later years when the mine output showed a more rapid rate of increase. That this reduction is not more marked is possibly due to the increased community and Shire Council power usage per head of population.INTRODUCTIONThe geographical position of Mount lsa, far from any large regional power supply Authority, dictated the policy that the Company be responsible for the production and suppiy of all power required for the plant operation. The Company also, in November 1937, accepted responsibility for the supply of a part of the power requirements of the township of Mount Isa. The history of power supply to the Mine may be divided into several phases.1. The supply Of lighting and power during the first plant construction period 1929-1931.2. The construction of the first section of the Mines Power Station, comprising Nos. 1 and 2 turbo alternators and boilers.3. The addition of No. 3 turbo alternator and boiler.4. The addition of No. 4 turbo alternator and boiler.5. The addition of No. 5 boiler.6. The addition of a. 2 turbo blowers for air supply to the Copper Smelter converters; b. 1 turbo blower for air supply to the L.ead Smelter; c. 2 turbo compressors for compressed air supply to the Mine and surface plant.

Jan 1, 1961

By Archer Wheeler

The Boston & Montana Reduction Works at Great Falls, Mont., was formerly the reduction works of the Boston & Montana Consolidated Copper & Silver Mining Co., and continued as the reduction plant for the independent company until .June 1., 1910, when the consolidation of a large number of the operating companies of Butte was effected. It then became merged in the Anaconda Copper Mining Co. as the Boston Montana Reduction Department of the Anaconda Copper Mining Co. The history of copper converting at this plant, while not covering the entire period of the commercial use of the process in this country, does cover by far the larger part of it, and as the operations and appliances of the process have undergone many changes during the time, it may, perhaps, be of some interest to put the record of these changes into permanent form. The plan followed in the preparation of this paper has been to give first a brief chronological record of the principal events and changes and then, even at the risk of some repetitions, to give more detailed account, of some of these changes under separate headings. The headings for the complete paper are as follows: 1. General Chronological Review. 10. Development of Different Classes 2. Mechanical Manipulation of Converters After Class I. 3. Casting of Finished Copper. 11. Basic Lining. 4. Tamping of Linings. 12. Number and Size of Tuyeres. 5. Early Acid Linings. 13. Cast Copper Tuyeres. 6. Acid Linings With the Use of Ore. 14. Efficiency of Air. 7. Introduction of Flux Through the 15. Size of Converter Mouth. Tuyeres 16. Height of Converter. 8. Bottom Blast. 17. Summary. 9. Disposal of Converter Slag.

Jan 8, 1913

By J. -M. Lopez-Cuesta, C. Petter, B. Otazaghine, M. Batistella, R. Sonnier

"Kaolinite is a dioctahedral aluminosilicate widely used as paper filler and coating pigment. At the best of our knowledge, kaolinite is not widely used in polymer industry. Therefore, in this study, the flame retardant effect of kaolinite in ethylene vinyl acetate copolymer (EVA) and polypropylene (PP) were studied and compared with an alumina trihydrate (ATH) and Talc. Cone calorimeter results shows that the weight percentage of ATH in EVA/ATH composites must be at least 50 wt. % in order to reach an improvement in fire retardancy in terms of pHRR. In the case of EVA/kaolinite, even with 35 wt. % the pHRR is largely reduced. Comparing PP/Talc and PP/kaolinite composites at 30 wt. %, both fillers leads to same reduction in pHRR with a slightly better performance for PP/kaolinite composites. In both cases an intumescent behavior of kaolinite composites was observed that could slow the rate of the rising degradation products, allowing radical recombination reactions. Also, it was observed that kaolinite forms a protective layer on the surface of the samples, which could insulate the material. These behaviors (intumescence and formation of a protective barrier) could reduce the transfer of the degradation products to the flame and explain the better performance of kaolinite composites. INTRODUCTION The use of mineral fillers as fire retardants in polymer matrix are well known and widely studied [1]–[10]. Aluminum and magnesium hydroxides (respectively ATH and MDH) are the most widely used inorganic fire retardants. To achieve fire retardancy with these mineral fillers, about 50-60% loading is required which decrease the physical properties of the composites. The fire behavior of composite EVA has been the subject of many studies [4], [7], [9]–[15]. EVA copolymers are commonly used in the cable industry, due to their high ductility, even at high loading rates. In such applications, the flame retardant systems should be introduced into the polymer to improve the fire reaction. Many flame retardant systems have been tested but the most used industrially relates to formulations based on hydrated mineral fillers (aluminum hydroxide and magnesium hydroxide). Their low cost and reduced fumes generation explains their success. However, to obtain good performance with this type of flame retardants, it is necessary to incorporate high levels (up to 65 wt %), which severely impact other properties such as processability and mechanical behavior. The main modes of action of these flame retardants are the dilution of the gas phase, the endothermic decomposition and a barrier effect created by the inorganic oxide residue which may be improved by the incorporation of other components such as montmorillonites, silicas or talcs."

Jan 1, 2015

By G. A. Bezuidenhout, J. P. T. Kapusta, D. K. Chibwe

"Peirce-Smith converters (PSCs) are extensively used in the copper, nickel, and platinum group metals industries to remove iron and sulphur from the molten matte phase. This technology has not changed significantly since its inception in the early 20th century. The typical converting operation involves lateral purging of air/oxygen-enriched air into molten matte through a bank of tuyeres. This blowing operation occurs at low air pressure from the blowers, and the induced bubbling regime is considered inefficient from both a process and an energy utilization perspective. Inherent drawbacks include recurrent tuyere blockage, inevitable tuyere punching operation to clear airways, and low oxygen efficiency as a result of substantial air losses due to leakages.Investigations in the 1980s demonstrated1 that jetting into Cu and Ni converters could reduce or eliminate some of the process difficulties. In spite of these findings, very little progress has been made in the application of these concepts for converting of non-ferrous melts on a commercial scale.As part of its operational improvement and energy reduction initiative, Western Platinum embarked on a full-scale industrial evaluation of generating a jetting regime by using sonic injection. Prior to full-scale industrial evaluation, a numerical assessment was conducted to ascertain the feasibility of implementing sonic injection on Lonmin converters. The work included flow characterization at high injection pressures achieving sonic velocity at the tuyere exit. The 2D and 3D simulations of the three-phase system were carried out using the volume of fluid (VOF) and realizable k- e turbulence models to account for the multiphase and turbulence nature of the flow, respectively. These models were applied using the commercial CFD numerical code FLUENT.This paper discusses the key findings regard ing understanding of gas plume extension, velocity distribution, shear wall stress analysis, and phase distribution characteristics in the system. Plant trials are also discussed with reference to the commercial aspects of a fullscale implementation of sonic injection in the smelter."

Jan 1, 2014

By Howard E. Parkinson

In 1969, new coal mine health and safety legislation was enacted in the United States. As a result of this legislation, the Department of Interior, Bureau of Mines has carried out communications research aimed at developing whole mine communications for increased safety and efficient operation. The research has advanced and many promising results are now being demonstrated to the mining industry. However, there remains a challenge to further improve wireless communications within the mine workings, and through the overburden above the workings. The objectives for future research and development will be discussed, together with the physical and operational constraints that new mine communication systems must face.

Jan 1, 1973

By Z. G. Li

The large-scale vibrating screen has been applied widely in coal industry and other industrial areas as a kind of important device. As vibration mechanical device, it works very hardly and works in very bad environment so that the structure of screen is damaged easily. Therefore, it is very important that how to detect the fault of structure as early as possible to make the repair schedule reasonably and economically and to avoid the body hurt and device damage. As a kind of important structure of vibrating screen, the lower crossbeam is the main carrying structure and it is easily damaged, so it is regarded as a researched object in this thesis and it is tested under the load in the laboratory. Based on the test, acoustic emission wave signals can be got-ten by modern acoustic emission testing technique. Then, the ?wavelet packet - energy? from the characteristics of acquiring signals is used as neural network input vector. In the BP network structure design, the design of a hidden layer with variable number of BP network is established. Based on the error by contrast, the best nerve number can be identified in the hidden layer. Through integrated analysis, using Levenberg-Marquard BP study algorithm, network-training errors are relatively small, the acoustic emission signal is used in BP neural network as a pattern of recognition. In Matlab6.5, neural network model identification is created and taking advantage of nonlinearity and the ability of learning and memory of Neural Network, this model is fixed by training structure of network with training samples. The work presented shows that acoustical emission signal processing and research on early fatigue fault diagnosis based on the wavelet and the neural network is viable.

Jan 1, 2014

By Davide Grassi, Joel Joaquin Cortez, Giovanni Spagnoli, Nick Chittenden

Grouting is a technique used to improve the engineering properties of soils and rocks. Grouting techniques are classified under different criteria: injection method used, type of grout material injected, typical application, and the sequence of construction. The best-known criterion is the mode of entrance or admission of grout into the soil or rock. It is possible to identify therefore several grouting techniques: compaction, fracture, jet/mixing and permeation. The function of penetration grouting is to reduce the permeability of the soil or rock and/or increase the strength and density. In order to avoid displacement, permeation grouting shall be carried out at carefully controlled pressures and flow rates, using appropriate grouts. Colloidal silica is an innovative binder which has low viscosity (about 5 m·Pas), it is not toxic (pH lower than 9) and it is workable between +5°C and +45°C. This paper presents several case histories: a consolidation job related to the installation of a new sewer in North Italy in cohesionless soils, water stopping injection in a weathered granitic bedrock in California, permeation works in the US in sandy soils to improve excavation and the installation of sheet piles in the UAE. Results show that the colloidal silica an innovative and robust technology to perform grouting in very fine soils where conventional binders or micro-fine cements cannot penetrate.

May 1, 2022

By W. B. Greer

The performance of seals in boreholes, shafts, and tunnels is an important concern in mine safety, in the control of effluents from operating and abandoned mines, and in the underground containment of hazardous wastes (Einarson and Abel, 1990; Mining Waste Study, 1988). Despite the clear need for effective seals, few documented test results are available concerning the performance of in-situ seals. Some evidence indicates that horizontal or near-horizontal holes are especially difficult to seal properly (Kelsall and others, 1982). This research involved the installation, extensive hydraulic testing, removal, and post-test examination of a l0-cm-long by 10-cm-diameter cement grout seal in a near-horizontal borehole in limestone. The work was performed in an underground mine on Marble peak in the Santa Catalina Mountains, Arizona. A test hole was diamond cored in the re-crystallized limestone of the Escabrosa formation. The hole is 33.24 m long, 10 cm in diameter, and dips at 10.4 degrees. The hole extends between two drifts and thus is accessible from both ends.

Jan 1, 1992

By J. P. Hansen

Reducibility tests were run by the Bureau of Mines on an open hearth lump ore and four groups of pellets whose smelting characteristics had been deter-mined previously in the Bureau's experimental blast furnace. When reduction data from various tests were plotted on specially prepared paper l-(l-percent reduction/100)1/3 against time, the plots were linear. The iron-wustite inter-face therefore advances at a constant rate. The rate of the interface advance in mm/min was used as a reducibility index. The reducibility index measured at 900° C, using 0.45 cu ft hydrogen per minute varied inversely with the surface area of the sample. Even with carefully controlled surface areas, how-ever, duplicate reducibility indices varied considerably. When enough tests were run to give a stable mean, the mean reducibility index did correlate with blast furnace production for the four pellet groups. Results indicated that if the interface speed itself were to be used for correlation with blast furnace production, a sample size of about 180 grams of minus 0.742-plus 0.525-inch particles should be used with a test temperature of 900° C and a flow of 0.45 cu ft hydrogen per minute.

Jan 1, 1966

By Jia Ma, Zhi-Chao Liu, Kang Liu, Chun-Feng Li, Bao-Bin Tang

"The geological environment of the certain uranium-molybdenum deposit is very complicated. While the study of process mineralogy is relatively few, which restricting the processing and leaching effect of ores. According to reaserch on process mineralogy of this mine, the basis of ore processing can be provided. The main contents of research are the uranium occurrence state and the influence of H2O2 in acid leaching. By various methods and experiments, the process of uranium mineralogical characteristics in this deposit are systematically studied. The results show that the uranium is mainly in the form of independent uranium minerals. The structures of these uranium minerals are venous and disseminated in mineral fissures, or microgranular inclusions in quartz and feldspar. It is not appropriate to concentrate the uranium minerals by flotation beneficiation because that the loss rate of target metals via water leaching process is very high. The ores are suitable for being acid leaching directly with 6% – 8% of H2O2, and the maximum leaching rate of uranium can be 96.88%. INTRODUCTION The uranium ores with associated elements have a large proportion in uranium resources (Lei, et al., 2014, Xing, et al., 2006; Ritchy and Wong, 1985). The uranium and molybdenum are easy to be paragenesis in nature enviroment because of their similar chemical properties. Therefor the uranium-molybdenum associated deposits are widely existing, such as the sedimentary sandstone uranium deposit in American with vanadium and molybdenum, the sedimentary sandstone uranium deposits in French with vanadium (Chen, et al., 2014; Lounis, 1997). A certain epithermal porphyry uranium-molybdenum deposit in China is mainly controlled by the subrhyolite- porphyry and the fault zone (Lv, 2012; Rui, 2010; Liu, et al., 2010). The ore properties of this deposit are complex, which include the high alteration degree, and the fine grain size of the target minerals (Ma, et al., 2013). The ore properties and occurrence state are quite different during each mining stage. As a consequence, the consumption of reagent increased and the leaching rate declined as long as the continuously mining. The author explored the best leaching rate of target elements According to the basic research on process mineralogy of present ores, experimental study of water leaching and oxidizing acid leaching on different particle sizes."

Jan 1, 2018

By N. C. Trivedi

Natural calcium carbonate, commonly known as limestone is an abundant resource pretty much worldwide. Calcium carbonate occurs naturally as the main constituent of chalk, limestone, and marble. One of the unique characteristics of this abundant mineral is its versatility. Major markets for calcium carbonate are: paper, plastics, caulks and sealants, carpet backing, paint, and food additives. This broad spectrum of consuming industries has warranted producers of this industrial mineral to be innovative and quality focused simply to meet the ever increasing demands for performance. This need for improving performance of calcium carbonate has led to the development of new sources of calcium carbonate, natural as well as synthetic.

Jan 1, 2002

By F. E. Lathe

The method of feeding blast-furnaces to be described below is simply the application of well-known principles, and an attempt to carry that application to its logical conclusion. It does not involve radical changes in equipment, nor does it require unusual skill on the part of the furnaceman. In fact, much of its value lies in its very simplicity. Before giving details of the method it will be well to consider briefly the conditions under which it was used at the Nickelton plant of the British America Nickel Corporation, in the Sudbury district, before that plant closed down. The Sudbury nickel ore consists chiefly of pentlandite, chalcopyrite and pyrrhotite in a gangue of norite or greenstone. The proportions of sulphide and gangue vary widely in different mines, the former constituting about 45 per cent of the total in the British America sorted ore. The gangue is fairly uniform in analysis, carrying about 55 per cent Si02, 18 per cent A120 3, 13 per cent FeO and smaller quantities of CaO, MgO, Na20 and K20. The ore has been frequently described as refractory, a word which seems suitable when one considers the many unsuccessful attempts to smelt it pyritically, as well as the high percentage of coke normally used at all the plants in the district.

Jan 1, 1925

By Ednlund D. North

Discussion of the paper of Edmund D. North, presented at the Spokane meeting, September, 1909, and published in Bulletin No. 37, January, 1910, pp. 21 to 25. A. SCOTT REID, London, Eng. (communication to the Secretary*) :-As a constructor of several glass mine-models, I have read with much interest the description of the model of the Montana-Tonopah mine-workings by Edmund D. North. As an interchange of ideas and experience is always an advantage, and in view of the fact that such models are coming more and more into vogue, perhaps the following remarks on this subject may prove of interest to mining engineers generally and to Mr. North particularly. In the model of the Waihi gold-mine, New Zealand, which I constructed, a dust-proof case is used. The top, bottom, front, and two ends are of glass; the back only is of wood, painted a dull white, against which the mine-workings show very distinctly. Each mine-level is represented by a horizontal sheet of glass, supported on metal runners fixed to the uprights at each end of the case, in a manner similar to that described by Mr. North. The corner uprights are strengthened by having a metal band screwed to the inside face of each, to which the metal runners or supports for the sheets of glass are screwed in turn. The reason for having this additional strength is that as the mine is developed in depth, and fresh levels are opened, the increasing weight of the glass sheets, added to the model, caused the unsupported wooden uprights to bend slightly, so that the glass sheets-did not fit in with the desired nicety, and co-ordination was, to a considerable extent, lost. Strengthening the uprights in this manner is not important in models of mines in which only a few levels have been opened, or when the sheets of glass are small, but in the Waihi model there are 15 sheets of glass to be supported, and more to be added as development proceeds, and the weight is considerable.

May 1, 1910

By J F. Short

The jet piercing process, developed by Union Carbide Canada Ltd., is well established in blasthole production in open-pit mining. By this process, holes can be drilled, shaped and chambered for blasting. In suitable ore or rock formations, a considerable cost reduction can be achieved. This paper reviews the equipment used, relates how cost savings may be accomplished, and concludes with a mention of the most recent developments in this field. JET piercing and chambering, a process for blasthole production in open-pit mining, leads, in many instances, to improved drilling and blasting techniques and costs. It is a method of working rock with a supersonic flame and, to be most effective, depends upon a characteristic of the rock called spallability. Spalling, in this case, is the breaking away of surface particles from the rock body due to stresses caused by the thermal shock of the jet flame. Various rock properties contribute to this action, but, in general, the harder the rock the greater the spallability and the more effective and economical is the jet process. The jet process has the capability to drill, ream, shape and chamber holes for blasting.

Jan 1, 1965

By P Scholtz

Sustainability is one of those fuzzy words like innovation: everybody has an idea what it means, but if one starts asking for concise definitions then it becomes clear that everybody puts their own nuance on the meaning of these words. It’s not because these are difficult words per se, but rather because our understanding of them is highly dependent on the environment we work, live and play in. To remove any ambiguity and aligned with the risks that are faced by the human population today, the definition for sustainability that will apply for this paper is: generating value in the short term without destroying value in the long term.CITATION:Scholtz, P, 2018. Sustainable post-closure development – is it achievable?, in Proceedings Life-of-Mine 2018, pp 58–59 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018