Search Documents

By Finlay, J. S.

THE North Lily Mine started its career in an unusual way it was discovered by a geologist. The remarkable circumstance of driving a 2400-ft. drift into an unexplored country and "hitting her on the nose," indicates that geologists are sometimes numbered among those whom the Lord loves. Diamond- drilling from surface had previously shown the presence and position of the Ophir beds, and surface showings of pebble-dykes, faults, and bleached rhyolite indicated conditions similar to those at the Tintic Standard "Pot-hole." The discovery drift from the Tintic Stand- ard 700-level reached the North Lily orebody in January, 1926, and development and stoping were continued by Tintic Standard men and equipment until the North Lily shaft was sunk and put into service in May, 1928. The discovery drift was run on a cooperative basis by the Tintic Standard and North Lily mining com- panies. Finding the North Lily mine cost the North Lily company $26,000. The Tintic Standard Mining Co. furnished men and equipment to drive this discovery drift at a fraction of what it would have cost to find the orebody from surface. This was the beginning of the friendly cooperation that still exists. Through Tintic Standard ground the Tintic Standard paid two- thirds of the cost and the North Lily one-third; the cost of the drift through Eureka Lily, into North Lily ground, was paid by North Lily. Later, another drift from the Tintic Standard 900-level was run on the same plan, excepting that Eureka Lily paid its share of the cost; that is, the Eureka Lily paid one-third of the expense in Tintic Standard ground, and the Eureka Lily two-thirds and North Lily one-third in Eureka Lily ground. This 900-drift was driven by North Lily from the Eureka Lily line to near the North Lily west side-line. From this point the Chief Consolidated continued the drift well into Tintic Bullion ground.

Jan 1, 1929

By G E. Craig, W. M. Williams

A simple, easily constructed apparatus suitable for the zone refining of iron and other reactive materials is described. After eight passes at one inch per hour, the iron produced showed a marked drop in hardness to 49 Brinell. In addition, an arbitrarily -defined recrystallization temperature was lowered by about 35°C and the rate of grain growth greatly increased. CERTAIN materials, of which iron is one, are so reactive that they cannot be zone refined in any known container without becoming contaminated. For such substances, the floating zone method ( 1) may be used. In this method, the specimen is supported vertically in an inert atmosphere and the molten zone supports itself by its own sur-face tension. The method was first applied to silicon (2) and has since been used for other reactive metals such as zirconium and titanium. Smith and Rutherford (3) have previously reported on the floating zone refining of iron; the efficiency of the method for reducing the car-bon content was demonstrated on

Jan 1, 1962

By Richard D. Nichols

A new method of slaking lime has been developed by DENVER EQUIPMENT DIVISION of Joy Industrial Equipment Company and patented under U. S. Patent 4,261,953. The new method utilizes an attrition machine, commonly used in mineral processing circuits as a sand scrubbing device, to slake lime. The scrubbing effect of the attrition slaker continuously produces a fresh reactive surface so that further slaking may occur. This process allows for utilization of slaking all grades of burnt lime and most grades of dolomite lime. Testing indicates that poor grades of water usually not considered for this service can now be tolerated using the attrition slaker. The slaked lime produced is of higher quality, faster reacting and much less apt to produce scaling problems than previously experienced. The attrition slaker can be combined with a spiral classifier and ball mill to eliminate any need for grit handling or grit removal. The attrition slaker can be designed for all burnt lime tonnages up to the limit of 175 tph and 1" pebble lime size. Control can be maintained easily with minimal operator assistance. The equipment, the principals of process metallurgy, and the above topics will be presented.

Jan 1, 1982

By Hermes Vilchéz

El presente texto describe los beneficios de la apertura de los circuitos de flotación como alternativa de mejora en la performance metalúrgica de las concentradoras. El trabajo se efectuó en la empresa minera Los Quenuales, Unidad Iscaycruz (Lima), modificándose los circuitos cerrados a los abiertos y encontrándose los siguientes beneficios: el incremento del tonelaje de tratamiento sin aumentar equipos en los circuitos de flotación, la mejora en la recuperación y el grado de concentrados.

Sep 9, 2007

By M Rankin, F Medina, R Verburg

We conducted a preliminary assessment of an extensive deposit of historic tailings discharged over a period of 40 years to the shoreline along a Southern Peruvian coastline. The tailings formed an extensive beach approximately 2.4 km long and 300 m wide. The tailings consist principally of pyrite (37 to 59 per cent), hematite (nine to 20 per cent), magnetite (three to 13 per cent) and quartz (11 to 36 per cent). The present operating company was required to evaluate the feasibility of capping the ocean side tailings deposit, however, given the size of the undertaking and the potential to reclaim residual minerals from the tailings, it was prudent to first evaluate whether capping would in fact reduce the impacts to the marine environment. Therefore this preliminary assessment examined: 1. metals contamination in tailings, shoreline porewater and marine sediments; 2. reactivity of tailings and acid generation potential; and 3. the potential for biological effects from metal contamination in the uplands tailings (solid phase) and beach porewater. Based on mineralogy, column leach studies and chemical results, the upland tailings have a high geochemical potential to acidify and release metals, especially copper, nickel and zinc, should they be subject to oxygenated and aqueous conditions. But, the extreme arid climate results in very low potential for precipitation and virtually precludes the transport of acid drainage reaction products from the upland tailings towards ocean. Wind erosion caused by offshore winds is likely a small source of tailing transport to the ocean. Since some potential exists to reprocess the tailings in the future, capping does not seem justified at present.

Jan 1, 2003

"Chairman: Professor B. W. MacKenzieRapporteur: Professor D. A. PretoriusPapers:Optimum spacing for soil sample traverses by W. A. HodgsonEvaluation of geochemical data by C. J. LenzResearch in oil exploration decision-making by J. W. Harbaugh and A. Prelat A drill hole data bank by M. R. AndertonOre reserve estimation and depletion planning for a beach diamond deposit by M. M. OosterveldIn opening the session, the Chairman indicated that the papers and discussions would revolve about quantitative methods of analysis and optimization of various aspects of exploration planning. The five papers would cover a wide range of topics within a general theme of exploration analysis, and it would be appropriate, therefore, to present the. papers as representing a sequential information-gathering process, namely, (i)geochemical and geophysical types of surveying for the location and identification of anomalous zones, (ii) tren¬ching and drilling of the anomalous zones found, and (iii) further refinement of the data for ore reserve calculations and production planning.The first paper, which was presented by Dr W. A. Hodgson, dealt with the optimum spacing between soil sample traverses conducted during geochemical prospecting. The theme of the paper was that the critical sampling interval should be based on the concept of element continuity, and that this interval could be determined by means of a correlogram. Ensuing discussion concerned the probability of the method, designed for areas where dispersion was high, working in localities where dispersion was either low or virtually non-existent. In the latter eases, specific orientation surveys for varying topographic, climatic and geological conditions would possibly be more useful than the preparation of correlograms. A further suggestion was made that cost versus risk should be taken into consideration when deciding upon the spacing between traverses. A balance could be struck by mathematical optimization. If the exploration budget was fixed, then the variance of risk could be minimized.The second paper was a short contribution by Mr C. J. Lenz. Computer-based plotting and evaluation of geochemical prospecting results were carried out because the low cost of analysis in Rhodesia permitted very large volumes of data to be accumulated in mass-coverage operations. Anomalous areas were demarcated within different environments by selecting probability or population boundary values from frequency distributions. In the short discussion which took place it was debated whether the method should be used only in the early high-risk stages of geochemical exploration and whether the introduction of geological bias could influence the actual results of an exploration program."

Jan 1, 2014

By AIME

Annual production of more than 4,000,000 tons of 0.74 percent copper ore and coincident handling of over 5,000,000 tons of waste at the open-pit mine of Castle Dome Copper Co. near Miami, Ariz. takes a lot of power. Manufacturers have ever co-operated with mining companies in providing the required equipment to suit the problem. Power equipment suppliers have done much to make possible the economic and profitable production of copper from low-grade ores. In the future, as mining operations will necessarily handle even lower-grade ores, the ability of the manufacturer to supply the power and mechanical equipment to produce more metal at a fair and reasonable price will be the good right arm of the miner. About 27,000 tons of concentrate is produced from the 4,000,000 tons of ore.

Jan 1, 1948

By Paul A. Lahti

Independence Mining Company, Inc. (IMC) has for the past several years processed refractory gold ores at its Jerritt Canyon operation near Elko, Nevada. The ore is typical of those of the Carlin Trend and is refractory due to physical encapsulation of gold in carbon, pyrite, and arsenopyrite. It is also "preg robbing" due to the contained organic carbon that acts as a gold adsorber. Refractory ores require some form of pretreatment before cyanidation to enable economical recovery of gold. The metallurgical facility at Jerritt Canyon is unique in that it consists of two distinct pretreatment methods for the recovery of gold: a chemical process utilizing chlorine and a pyro-metal­lurgical process employing oxidative roasting. This paper pro­vides a comparison of the two methods highlighting flow sheets, pretreatment operation detail, performance comparisons, and pertinent environmental data.

Jan 1, 1996

Few people in the industry today are competent to comment on the O.G. system for vessel covers, but with papers as well prepared as Mr. Bradley's we will soon be well informed. I would like to direct these comments to Mr. Klaes of Ford Motor Company. Mr. Klaes' description of their steaming hood agrees with our experience at Weirton. We have been able to stay within design limits and, as a result, have had few problems with our auxiliary equipment. Our main problem, as with Ford, has been thinning of our vessel cover tubes. At Weirton, controlled circulation, high pressure boilers are in use as heat recovery units above the BOP vessels. The boilers are provided with "off cycle' oil firing equipment. A Venturi type wet gas scrubber follows the boiler to complete the vessel draft system.

Jan 1, 1972

By Thatcher R

In areas where undeveloped land represents a scarce resource, an upgraded post mining land use can result in economic benefits to both the mining company and to the community. A study undertaken at Allied Queensland Coalfields Ltd's Aberdare Colliery located between Brisbane and Ipswich during 1986/1987, assessed the costs and benefits of developing the site following mining for grazing, forestry and residential uses. The proposed final land use plan comprised a combination of these uses which can be upgraded to higher valued uses once subsidence monitoring of backfilled opencut areas and dumps indicates that total settlement has reached acceptable levels. The study involved the documentation of existing site environmental parameters and the delineation of site opportunities and constraints. The unpredictable nature of settlement over backfilled opencuts and overburden dumps represents the major constraint to urban development on mined areas.

Jan 1, 1987

Downtime cannot be tolerated on electric shovels whose cost may approach or exceed $400,000 each. The same may be said for larger-variety off-highway trucks which require an operational expenditure upwards of $50 per hour. One company, for instance, in order to ensure a more continuous operation, has specified centralized lubrication for all of its new equipment. In wet or dry weather, the mining of asbestos can place undue strains on machinery and other equipment. When the mineral is dry, its dusty, loose fibers work their way into crevices, and when wet, the glutinous asbestos may adhere to axles, gears and other wear components. Such conditions are multiplied during the extreme cold winters of eastern Canada. It is more difficult to lubricate and maintain equipment, and erosiveness becomes more punishing to wear parts. Resultant breakdowns rapidly drain off profits.

Jan 1, 1971

Human resources (HR) practitioners use a general suite of tools that they adopt to suit their company needs and profile. This paper will cover the main areas of a selection and recruitment process from applying for a job, resumT writing, participating in an interview finalising the job offer. A holistic recruitment process has many facets to it. These processes can be quite sophisticated and technical but at the end of the day they are designed to identify talent. A recruitment process will generally include: ability testing (usually online);telephone interview;face to face interview;behaviourally based interviews;psychometric assessments;presentations;simulations (independent or team based); and assessment centres, etc. Understanding the basis of these tools will go a long way to prepare you for the job market, enhance your performance in a recruitment process and stand you out from the pack.

Jan 1, 2008

"In the mining industry, high-level commitments to adopt sustainability have been made at the corporate levels of mining companies, but there continue to be problems when attempts are made to adopt these high-level sustainability aspirations and translate them into appropriate targets and methods at the more-specific operational level. The integration of sustainability principles into day-to-day minerals processing operational decision-making processes has unique challenges that are not addressed adequately by current tools and methodologies. A proposed methodology to achieve integration of sustainability at the operational level will direct the systematic and rigorous identification and characterisation of sustainability issues in an operation. The methodology allows different approach strategies for assessment, comprehensive accounting of sustainability indicators and has the ability to identify sustainability issues which may have significant business implications that cannot be identified using traditional analysis processes."

Jan 1, 2011

By F. Milton Lewis, Edward S. Frohling

The information which is required for' a preliminary feasibility study and the additional information which is required for the final feasibility study on a new mineral deposit are discussed. The preliminary feasibility study is made from very little information and at a minimum cost to the owner. However, the outline for the preliminary report is similar to the one used in the final report. In this manuscript, it is assumed that the results from the preliminary study are favorable and the owner authorizes a final feasibility study by an outside engineering company. The type of organization for completing this final feasibility study is described. The final reports includes all information and data relative to this new mineral deposit. This information is presented so that it may be understood by financial people as well as by technical people.

Jan 1, 1978

What is `environmental risk'? There are two possible perspectives: (a) The risk that mining activity will have an impact on the environment. (b) The risk that due to a perceived impact on the environment, the mining activity is at risk due to some legal consequence. This paper is concerned with the second of these perspectives, and particularly with the way in which mining companies can manage that risk. Environmental risk - possible legal consequences The risk is that the mining operation will be disrupted. Disruption may be: (a) Physical. The mining activity can be stopped, altered, or modified, or something additional can be required to be done. (b) Financial. Penalties (up to $1M) on corporations and in some states on both directors and managers. Land may also be included on a contaminated land register (significant impact on asset valuation).

Jan 1, 1994

By Immo H. Redeker

The Asheville Minerals Research Laboratory at North Carolina State University is engaged mainly in applied nonmetallic mineral processing research to assist the North Carolina mining industry. The laboratory helped to bring the flotation process to North Carolina feldspar. spodumene, mica and phosphate producers and it maintains a versatile batch and pilot plant. The conservation of mineral resources through improved processing methods has been the object of most of the laboratory's projects. Current laboratory work is sponsored by three feldspar companies, the State of North Carolina, and the U.S. Bureau of Mines. This work is aimed at reducing the amounts of feldspar tailings in the Spruce Pine area. Mineral dressing techniques are applied to these tails to reclaim salable mineral products such as feldspar, mica, quartz, and to make a more uniform material for possible ceramic and other applications.

Jan 1, 1970

By Kenneth E. Skiff

INTRODUCTION United Nuclear Corporation and Homestake Mining Company are partners in a major uranium mining and milling venture near Grants, New Mexico. The partnership was formerly called Homestake-Sapin Partners and was recently renamed United Nuclear-Homestake Partners (UN-HP). The mill, originally built in 1958, had a capacity of 1,650 tons per day. With subsequent improvements and the addition of the adjacent Homestake - New Mexico Partners mill, the UN-HP mill is currently rated at about 3,500 tons per day. An alkaline type leach process is utilized by the mill. Milling consists of five basic steps: A. Ore handling and preparation B. Extraction C. Solid-liquid separation D. Precipitation and purification E. Product preparation MILLING Ore Handling and Preparation The primary source of ore for the UN-HP mill is from its four

Jan 1, 1983

By Bart Hogeweg

The development of deep sea mineral deposits creates a new horizon for the mining industry. In a field where mining technology meets deep-water offshore engineering, new challenges are faced to come to the successful exploitation of these deposits. With the absence of proven technology for the mining of these minerals, a ?technological green field? is entered. IHC Merwede (IHC), a global market leader in the dredging and wet mining industry, is on the frontline of these developments. MTI Holland, IHC Merwede?s research and development company, has undertaken a number research efforts focused on the successful development of technology for the mining of deep sea minerals. This paper highlights a number of these efforts and illustrates IHC?s continued dedication for the research and development of technology to enable the commercial mining of deep sea minerals.

Jan 1, 2008

By Gary E. Butts, Paul R. Smith

Introduction The design of a mineral processing flowsheet involves many factors. The importance of the sample can not be overemphasized. Competent and thorough mineralogical examinations are important as an aid in designing the test program. Designing and conducting the laboratory test program is basic to the design of the flowsheets. In the project under consideration a flotation pilot plant was conducted to prove the process and to provide a realistic prediction of metallurgical results. Moreover, the pilot plant operation provides important pilot plant design data. Finally, accurate and clear reporting is essential so that the information developed can be utilized advantageously by the client and the engineering firm. The design of a minerals processing flowsheet is a team effort. Engineers from the mining company, the research organization, and the engineering firm all contribute to the effort.

Jan 1, 1978

By D. R. Spink, D. N. Okuhara

Two reagents have been proposed for the commercial extraction of copper from leach liquors, namely LIX64N produced by General Mills Chemicals, Inc. and Kelex 120 produced by Ashland Chemical Company. Each of these reagents consists of an active extractant and an additive. In the LIX system, the additive improves the kinetics of the extraction reaction whereas for the Kelex system, the additive acts primarily as a third phase inhibitor. Equilibrium and kinetic studies have been conducted with both systems. In general, the Kelex system effectively extracts copper at a lower pH than LIX64N; furthermore, the rate of extraction with Kelex is considerably faster than with LIX which indicates that systems employing the Kelex extractants might also be able to employ agitated columns rather, than mixer- settlers which are absolutely necessary for effective extraction with the LIX reagents.

Jan 1, 1973