Search Documents

The heavy media cyclones at Argyle Diamonds are subjected to extremely abrasive service conditions and have been the subject of a development program from the time the first ore was treated in the AKl processing plant. In the past ten years the cyclones have been re-engineered from a standard DSM design, in which some components would only last four days, to the current Argyle design in which the minimum component life is 175 days. Development has focused upon the elimination of turbulence in the cyclone and combating unavoidable abrasion through the use of appropriate wear materials.

Jan 1, 1996

By E. M. Haynsworth

The disposal of phosphatic clays has presented a problem to the phosphate industry since the mining of phosphate rock first began. As the flotation process was introduced in the late 1920's, the problem of clay disposal was increased significantly since clay is present in proportionally greater quantities in reserves yielding flotation concentrates. Because of their physical character and the tremendous surface area per unit volume, these clays have the characteristic of retaining large volumes of water as they are slurried during processing. The phosphatic clays with which we are dealing consist primarily of apatite, wavellite and montmorillonite. In the beneficiation process, we remove the -150 mesh material as waste. However, the particles are essentially smaller than -325 mesh, and more than 70% are smaller than three microns. The disposal of clay and the recovery of a portion of the water require settling areas with a capacity ranging up to 2 cubic feet for each cubic foot of phosphate matrix mined. According to a recent study by the Bureau of Mines, the average cost for disposal of these wastes is 24.5 cents per ton of, product (U. S. Bureau of Mines Circular 8404). This is a major cost of phosphate rock production.

Jan 1, 1970

By H. L. Zimba

Flotation involves the selective levitation of mineral and its transfer from cell to launder. The flotation rate is the rate of this transfer. It may be defined by the slope of a recovery-time curve for any cell in a bank or at any time in a batch operation. The objective in flotation rate study is an equation expressing the rate in terms of some measurable property of the pulp. This can be either the concentration of floatable mineral in weight per unit volume or a relative concentration, which will be a function of the recovery. A rate equation for an actual flotation pulp will contain at least two constants, both to be determined from the collected data. The data used in this paper were collected from bench-scale flotation tests on Konkola primary mill cyclone overflow at various pulp densities and pre-flotation thickener underflow at a pulp density of 35% solids by weight.

Jan 1, 2009

By William P. Blake

In view of the present exposition at Atlanta, and the timely meeting of the Institute in that city, and the expressed desire of the Council for contributions to the knowledge of the mineral resources of the Southern States, I may be permitted to offer some desultory notes upon the subject, chiefly in the form

Jan 1, 1896

By C. Chapman, P. Cowx

"INTRODUCTIONTetronics Research and Development Co. Limited has installed several plasma torches for steel heating in continuous caster tundishes. An extensive demonstration program on a 14 tonne tundish reported the following advantages of plasma heating.• close control of steel temperature to ± 5°C;• a reduction of the furnace tapping temperature of up to 20ºC, leading to savings in energy and refractories costs ;• improvement in steel quality, to produce a slab product with an equi-axed crystal structure and a reduced number of large sub-surface slag inclusions;• the virtual elimination of oxygen pickup in the tundish; and• the capability of making ferroalloy trim additions to the tundish to permit a change of steel grade during casting, greatly decreasing inventory costs.The Need for Tundish HeatingIn the continuous casting of steel, the function of the tundish is to transfer the molten metal between the ladle to one or more continuously fed casting moulds. Figure I shows a typical temperature profile of molten steel in the tundish over the first cast cycle. It is observed that a rapid drop in temperature occurs both at the start of the cast, due to the tundish refractories absorbing heat, and also during ladle changeover. In addition, as a result of thermal losses through the ladle sidewalls, there is a gradual decline in the bulk steel temperature over the entire heat cycle. Consequently, in normal tundish operation, it is necessary to cast with a high superheat (25°C to 30°C + above steel liquidus temperature) in order to prevent freeze-up of the strand. Problems of high temperature variation and the potential of the steel solidifying in the tundish are greater for small caster units of low thermal mass . A high steel superheat increases the steelmaking vessel process time and refractory wear and prevents the formation of a uniform equi-axed solidification structure in the cast steel, resulting in centre line segregation and porosity. The large drop in the casting temperature that occurs during unsteady state operation causes an increase in the number of sub-surface inclusions, reducing the value of the product. Accordingly, plasma heating may be employed to maintain the molten steel at an optimum temperature to produce a slab of consistent quality."

Jan 1, 1989

By T. Egleston

The necessity of using a refractory material capable of much greater resistance to chemical action and having a far higher melting-point than those which contain silica, which melt and sweat off in the furnace even when not exposed to bases forming with silica more or less fusible compounds, has led to a careful practical study of all those materials which contain very refractory bases. The results of these researches, extending over several years, and made on a very large scale in many of the largest works in Europe, are of the highest interest, not only considered as a step in the progress of the study of the materials themselves, but in the application of refractory materials to metallurgical uses in general. The result of the experience of the last seven years with these basic materials, as in general with all such substanccs, is that natural products cannot be used as such. They are either too uncertain in their quality, contain substances which may in certain cases be very injurious, or, when in a condition in which they might be used, are so rare as to become practically unavailable for employment on a large scale. The materials that may he used are therefore not only limited in number. but they must be prepared artificially. When the use of basic artificial material is further extended, no doubt the number of these substances will not only be greatly increased, but the methods of preparation will be both perfected and cheapened to such an extent as to permit their application in processes for which they have hitherto proved too expensive. The quantity of refractory materials required for making ingots will he from 130 to 150 Ibs. per ton, or between 6 and 8 per cent. of the metal produced. In an establishment producing 2000 to 3000 tons of steel per week, considerable space is required to handle the basic materials properly. It is proposed in this paper to briefly discuss these basic materials and their application in the only two metallurgical processes where they have as yet been applied. These are the basic Bessemer and the basic open-hearth process, known as the Thomas-Gilchrist processes.

Jan 1, 1886

By W. C. McClain

In the design of underground excavations, rock mechanics considerations are nearly always based on an elastic behavior of rock. Most rocks do exhibit a certain amount of elasticity, and the application of principles and concepts of elasticity to rock mechanics problems has been largely responsible for progress in the field over the past 10 or 15 years. NO doubt the theory of elasticity will remain the most useful analytical tool available for both the design of underground openings and the interpretation of phenomenological data. Dr. Cook's analysis of rock behavior based on energy considerations represents a significant new approach to mining rock mechanics problems. Although the foundations of this analysis are somewhat broader and more general than elastic analysis, the development and applications are grounded almost entirely in the theory of elasticity. It has long been known1,2 that all rocks, even granites and dense limestones, exhibit nonlinear time-dependent strain properties to a greater or lesser degree. Creep strain (that is, deformation under constant stress) in salt, potash, and trona can be several orders of magnitude greater than instantaneous elastic strain. Design of underground workings in these materials must incorporate provisions for these strains and must therefore go considerably beyond elastic analysis. Some of the principles of underground design in highly plastic materials will be discussed in this paper. Since all rocks, especially when highly fractured, exhibit a certain amount of creep-type strain, these concepts should be at least recognized in any rock mechanics problem. The discussion will be illustrated largely, but not entirely, by examples drawn from

Jan 1, 1967

By Robert M. Grogan, Gill Montgomery

Fluorspar, the commercial name for fluorite, is a mineral composed of calcium fluoride, CaF,. Its valuable properties are due to its content of fluorine, and it is the principal commercial source of that element. The name is derived from the Latin word "fluere," to flow, because the mineral has a low melting point and is used in metallurgy as a flux. Cryolite is a sodium aluminum fluoride, Na,AlF,. It is a rare mineral which has been found in commercial quantities in only one place in the world, Greenland. Small amounts of it are shipped from stock in that country, and its place in industry has been taken over almost completely by synthetic cryolite. Because of the relative unimportance of cryolite, discussion of it has been relegated to a short section at the end of this chapter, which is principally concerned with fluorspar. History Fluorspar was used for ornamental purposes by the Greeks and Romans, who fashioned such things as vases, drinking cups, and table tops from it. Various peoples including the Chinese and the American Indians carved ornaments and figurines from large crystals. Its usefulness as a flux was known to Agricola (1564), who wrote about it in 1546. Mining began in England about 1775 and at various places in the United States during the period 1820 to 1840. Production became substantial following the development and widespread adoption of the basic open hearth method of making steel, in which fluorspar is used as a flux. After that, production and usage were stimulated by growth in the steel, aluminum, chemical, and ceramic industries and were accelerated by World Wars I and II. Fluorocarbons entered the picture in 193 1 and the use of anhydrous hydrogen fluoride (HF) as a catalyst in the manufacture of alkylate for high octane fuel blends began in 1942. The development of the froth flotation process in the late 1920s, a differential flotation scheme for separating fluorspar from galena, sphalerite, and common gangue minerals in the 1930s, and the application of heavy-media concentrating methods to the treatment of low grade ores in the 1940s were outstanding technological contributions that enabled increased production of fluorspar concentrates. In recent years the development of pelletizing and briquetting processes for making flotation concentrates into gravel-size particles for use in steel furnaces and the development of more efficient and selective flotation schemes for treating crude ores containing abundant dolomite and barite have been major improvements in the industry.

Jan 1, 1975

By E. J. Ripling, S. I. Liu

IT has been shown in a number of recent publications that much information on the mechanical behavior of metals can be gleaned by first deforming test specimens under one set of conditions, and then evaluating the effect of this deformation by means of a subsequent tensile test. A straining procedure of this type has been applied to study the flow behaviors of a number of metals.1, 2 In these studies the prestraining and testing were both tensile strains, while the straining temperature was varied between the prestraining and testing steps. These data indicate that there is a more or less general flow behavior exhibited by all metals which are pre-stretched at one temperature and then tested in tension at a second temperature. Prestraining a metal at a high temperature produces a lower yield strength during the subsequent low temperature strain than would the same total strain at the lower temperature. On reversing the order of the strains, low temperature prestraining produces a higher yield strength during the subsequent high temperature straining than would a single high temperature strain of the same magnitude. Unlike the flow behaviors, the fracturing characteristics of metals when prestrained under one set of conditions and tested under a second set of conditions is quite material dependent. The fracture behavior of a number of steels2" as well as of a commercially pure zinc,4 have been investigated by these two-step tests and was found to depend upon the position of the transition temperature with respect to the prestraining and testing conditions. Since these fracturing phenomena are complicated by the appearance of the transition temperature, it has been difficult to reliably define the basic effect of a two-step straining procedure in fracturing. Metals crystallizing in the face-centered cubic system do not exhibit transition temperature effects so that the mechanical characteristics obtained on these materials could serve as a base for two-step straining behaviors. Consequently groups of specimens of the aluminum alloy 24s-T4 were prestrained various amounts at room temperature in either tension or compression after which these strained specimens were further strained to failure, or tested in tension, at either room or some lower temperature. Other groups of 24S-T4 specimens were prestretched at various low temperatures after which these were tested in tension at room temperature. These straining techniques then made it possible to compare the behaviors of aluminum with the behaviors previously presented for steels. Material and Procedure The commercial aluminum alloy 24S-T4 in the form of 3/4 in. rods was used in this investigation. The material was subjected to the following treatments before machining: 1—resolution treating at 920" & 10°F for 45 min, 2—quenching in water at room temperature, and 3—aging at room temperature for four days. The re-heat treated material was then machined to either of the specimen shapes shown in Fig. 1. Fig. la shows the threaded-end specimen used for prestraining in compression. Fig. 1b shows the specimen used for both prestrain in tension and final testing. The material subjected to precompression in the form of the specimen shown in Fig. la was re-machined to the specimen shape in Fig. 1b for final testing. Prestraining in tension and final testing were done without any intermediate machining. All straining was performed on a 10,000 1b Riehle tensile testing machine. Tensile strains were conducted in a specially designed concentric fixture which produced an eccentricity of less than 0.001 in." The change in diameter at the minimum section of

Jan 1, 1954

By Andrew Ritter, Victor I. Montenyohl, Stephen R. Winzer

Thirty-seven open pit production blasting operations have been monitored using high-speed cameras running between 500 and 7000 frames per second. Analysis of the resulting films reveals irregularities in timing including sequencing errors and crowding (holes firing less than 8 ms apart), confirming results of laboratory testing of ms delay blasting caps (Winzer, 1978). Where blasting parameters are otherwise constant and within recommended guidelines (stemming, spacing, burden, etc.), timing problems dominate the overall performance of the blasting operation. Model tests in layered Homalite 100, designed to simulate joint or bedding planes in rock, indicate the importance of the stress waves generated by the explosive in developing the crack network which is ultimately responsible for the fragmentation seen in the resulting muckpile. These mechanisms are strongly supported by high-speed film studies at Pinesburg, Maryland. Experiments in controlling relief in deep shots (where depth approaches the lateral extent of the bench blasted) using borehole geometry and hybrid initiation systems (electronic timer and pyrotechnic delays) were carried out. The results suggest that the 1 me/ft. of burden guideline developed by Bergmann et aI., 1974 is too short, and that much longer times are necessary to optimize fragmentation and muck digability. Longer times are found to reduce noise, vibration, and flyrock.

Jan 1, 1979

By Lester G. Morrel

THE RICH and varied occurrences of metallic ores in Australia, extensive nickel deposits on New Caledonia and phosphate rock on several widely scattered small islands were important aspects of the economy of the South Pacific area. Relatively small quantities of gold and nonmetallic minerals produced in New Zealand, Fiji, and the Territory of Papua-New Guinea remained important to the domestic economies of these islands, but had little importance to overall world mineral supplies. The value of mineral commodities produced in this area in 1964 was estimated at $658 million,3 compared with $585 million in 1963. The year's greatest commodity gains were in bauxite and aluminum, beryl concentrate, manganese ore, nickel smelter products, tin, and coal. Annual increases were recorded in virtually all countries and possessions in the area except Papua-New Guinea, where the drop in output of alluvial gold accounted for a decline of about $160,000. Mineral industry activities in Australia overshadowed those in all other parts of the South Pacific in 1964. Outstanding developments were the sales contract negotiations and physical preparation for exploiting the rich iron ore discoveries in Western Australia, the initiation of domestic crude oil production, the commissioning of two new steal mills and an alumina refinery and a start on the new alumina-aluminum project based on Cape fork bauxite deposits. The principal mineral development in 1864 in New Zealand was the progress on plans of the Newzealand Steel Co. to use indigenous iron sans as the resource base for a local steel industry. In New Caledonia, additions and expansion of the nickel mining and smelting facilities continued throughout the year. Plans for extensive geophysical studies were announced by the Government Geological Departments of British Solomon Islands and Fiji.

Jan 1, 1966

By J. F. Myers, S. D. Michaelson, F. C. Bond

THIS work was undertaken with the object of collecting plant data on rod milling, making laboratory tests on representative samples of the various ores, and arriving at a basis for comparing the relative efficiencies of different mills operating on widely different materials and under varying conditions. These efficiencies consider only power consumption and do not include the other elements of operating costs. The over-all economic efficiency may be quite different from the consumption efficiencies with which this paper is concerned. It is hoped that these collected data will be of value in indicating the most favorable conditions of rod-mill operation. Operating-plant data on 14 different installations from 11 plants throughout the United States and Canada were collected, and laboratory tests were made on samples of these ores. The plant rod mills were all operated wet, and either in open circuit or with circulating loads so small as to be negligible. Data were obtained on one roll-crushing operation at the Utah Copper Co., for comparison. The rolls were operated wet in closed circuit with 10-mesh vibrating screens, and with a high circulating load averaging about 600 pct. This particular roll operation can be considered as a model of efficiency. The collected plant data are necessarily incomplete in some instances. Each ore was assigned a code number, and the name and location corresponding to the code number are listed in Table I when permitted. [ ] The power data in every instance refer to motor input. Net power was reported by the operator for samples I-39 and I-45, and this was increased by 20 pct to compensate for motor losses and power factor. The plant rod-mill data are listed in Tables 2 and 3. In Table 2 the speeds are calculated on the basis of partly worn rod-mill liners 2 in. thick. Where D

Jan 1, 1947

By Agrawal R. D, Kapoor M. L

Activity of FeO in the ternary system MgO-FeO-CaO in contact with metallic iron has been measured at 1000 K employing the cell.PtIFe, (Mg, Fe, Ca)OIZr02 - CaOIFe, FeOlPt. Measured data are used to study the phase stability relations in the system MgO-FeO-CaO and an isothermal section at 1000 K through this system is drawn.

Jan 1, 1987

By Nobuhiro Oguma, Yuji Mizuta, Hideya Sato, Shigehiko Iwahori

"Recyclable materials containing copper and precious metals have been treated at the Mitsubishi Process in Naoshima. In 2003, a new incinerating and melting plant (pre-treatment plant) for waste materials, such as shredder residue of automobile and scrapped appliance, was constructed. All of produced slag/metal mixture is treated at the Mitsubishi Process, and which results in the significant increase of recyclable materials treatment. The combination of two processes has realized a highly efficient and environmentally friendly system for recycling valuable metals in the waste which used to be sent to a landfill. Naoshima continues to make efforts to achieve the highly efficient operations of the two processes, and plans to increase the treatment of recyclable materials further. This paper summarizes the recent operations and the various improvements implemented in the pre-treatment plant.IntroductionRecyclable materials containing valuable metals such as copper and precious metals have been treated at the Mitsubishi Continuous Copper Smelting and Converting Process (Mitsubishi Process) since the start-up in 1991. In the early stages, recyclable materials consisting mainly of metal scrap were charged into the process and the treatment had been increased steadily. In order to promote the recycling business, treatment of various kinds of materials including printed circuit boards was started. However, the treatment hit the ceiling due to a limitation of furnace boiler capacity, since they contained large amounts of combustible materials. In addition, severe corrosion of boiler tubes was caused by halogen contained in recyclable materials."

Jan 1, 2012

By H. P. Wheeler

WHEN Germany invaded Poland in September, 1939, the only operating helium plant in the United States was that near Amarillo. Texas, supplied with helium-bearing natural gas from the near-by Cliffside gas field. Today the Bureau of Mines has five plants capable of producing more than 25 times the prewar helium output of the Amarillo plant. Two of the plants have received Army-Navy "E" flags for their part in the faraway "Battle of the Atlantic," where heliumfilled Navy blimps chased Adolf Hitler's submarines away from American shores. Meteorologists, watching balloons carried high into the stratosphere by helium, determined weather conditions that influenced the selection of D-day and dates for other military operation. Demand for helium doubled overnight when the Navy decided to expand its lighter-than-air activities; and as the blimp patrol proved effective, the helium demand became ever greater. A tribute to the success of the Bureau of Mines in meeting the demand for helium was paid by the late Secretary of the Navy, Frank Knox, in a letter to the Secretary of the Interior on April 10, 1944. Secretary Knox wrote, in part,

Jan 1, 1945

By Houston Kempton, Tim Dyhr, Andy Davis, Mark Bloom, Connie Travers, Dave Atkins, Jeff Deen

INTRODUCTION Historical mining activities in the Robinson Mining District, in the Egan Range of east-central Nevada (White Pine County), resulted in five open pits (Veteran, Tripp, Liberty, Ruth, and Kimbley Pits), several large mine-waste dumps, and numerous underground workings developed for copper, zinc, gold, lead-silver, and manganese (Figure 1). Groundwater percolating downward through the copper sulfide ores produced a blanket-like supergene zone enriched in copper, which has been one of the primary objectives of mining since the early part of this century. To obtain permits for future operation, an EIS was conducted that evaluated future pit- lake chemistry, groundwater quantity and quality issues, transport of water and solutes subjacent to a proposed tailings impoundment, and the potential for waste dump acidification. AREA HYDROGEOLOGY The mine area is on a ridgeline draining to the Steptoe Valley to the east and to the White River Valley to the West. Precipitation in the Robinson Mining District ranges from a low of 15 cm (6 in.) per year in the valley to more than 50 cm (20 in.) per year in the surrounding mountains. Evapotranspiration exceeds precipitation, leading to a net loss of water from the basin as either surface flow or underflow to the north at Currie, Nevada (Eakin et al. 1967). The White River Valley, which lies to the south and west of the mine area, includes approximately 4,200 km2 (1,620 mi2) of the upper part of the Colorado River Basin. This valley is 112 km (70 mi) long, 32-48 km (20-30 mi) wide, and like Steptoe Valley, evaporation and transpiration exceed precipitation (Maxey and Eakin 1949). The local groundwater flow system in the Robinson Mining District and the proposed mine area is dominated by two main components: (1) a groundwater mound or high between the Ruth Pit and Murry Springs, and (2) a shallow groundwater flow divide that follows the ridge crest south of Ruth, which contains the Veteran and Tripp pits. Besides the alluvium, the main hydrostratigraphic units controlling groundwater flow are limestones, shales, and sandstones, along with the intrusive quartz monzonite stocks. Based on the piezometric surface measured in October 1993, three distinct groundwater regions were identified. In the Giroux Wash area, an apparent fault runs between WCC-G1 and WCC-

Jan 1, 1995

By P. B. Butler

IN common with others, the zinc industry found itself after the war largely over-capitalized, a condi-tion which still exists notwithstanding that Tri-State production has doubled since prewar days. This is partly due to the abnormal war demands and partly because of the war impetus given to research, a stim-ulus that because of its success has persisted (and probably will persist) constantly since then. Improved practice and metallurgy resulting from research are today responsible for an increased pro-duction in the Tri-State district of 15 per cent over the practice of five years ago, and the giant strides in this respect in the western states together with the more moderate advance in the Tri-State district has thrown out of equilibrium the more or less balanced production of before the war and production has con-sequently gained on consumption, a condition resulting in rapidly narrowing profits in the Tri-State field, where the present average cost is actually greater than the price received for our product. Despite this condition, no thinking person will de-plore the cause or means used to achieve a greater production and, as this progress is merely the economic application of intelligent thought, it follows that equal effort and thought may be expected to produce the remedy. It has been suggested that the practical application of research has resulted in less need for man-power and consequently in the lessening of employment to common labor and to engineers. I cannot think that such is the case although personally I have received more ap-plications for employment during the last two years than ever before. But when one considers the strides production of all commodities has taken, it is difficult to reconcile this immense development with the possible increase in pop-ulation especially in view of our stringent immigration laws. Whether or not improved industrial methods are responsible for the lessening of employment the ques-tion as to the wisdom of such improvement is hardly debatable. While the Tri-State district of Oklahoma, Kansas and Missouri continues to be the leading factor in the zinc¬mining industry, gradually lowering prices during 1925 and 1926 and a. decided drop during 1927, have de-creased its production almost 20 per cent, this tonnage having largely been replaced by western concentrates.

Jan 4, 1928

By R. Pazhianur

Many investigators conducted surface force measurements between hydrophobic surfaces in water, and observed attractive force that was substantially stronger than the van der Waals attractive force. The excess force was appropriately referred to as “hydrophobic force”, for which many different theories have been put forth by numerous investigators. In an earlier publication (Yoon and Ravishankar, 1996), it was suggested that the hydrophobic force maybe due to the interaction between the large dipoles created by the surfactants adsorbing on solid surfaces in patches (or domains). In the present work, a mathematical model has been developed to further elaborate the theory.

Jan 1, 2003

Wetherstones gold deposit is located just east of the township of Lawrence, in the Otago District of the South Island, New Zealand. The paper will describe aspects of the mining and exploration history of the Wetherstones gold field, current knowledge of the geology of the deposit, and speculate on possible outcomes of exploration in the modern era.   As at the famed Gabriels Gully situated nearby, most of the Wetherstones gold is/was contained in, or recycled into modern drainages from, the Blue Spur Conglomerate (æBSCÆ). The BSC is the basal member of a wedge of auriferous non-marine sediments of latest Cretaceous age which are tilted against the Tuapeka Fault Zone, a structure of regional dimensions. In particular mineralisation of elevated grade (which cannot yet be reliably estimated) appears to be concentrated in an elongate basement depression (ægutterÆ) of width around 100 m, variable thickness to a few metres, and axial length in excess of 500 m. The gutter plunges from the base of alluvial mining (where it has been partly exploited by underground methods) to depths of more than 100 m, beyond which it remains open and untested.   The prospects for a revival of mining at Wetherstones depend upon confirmation of what is here inferred to exist, and the discovery of additional gold. The economic prospects of the project however are enhanced by what is known or indicated of the geographic location, and anticipated geologic, mining and metallurgical characteristics of the mineralisation, and consequent anticipated environmental management issues.   The recognition of gold contained in pyrite in the BSC represents an upside to project economics which has never previously been evaluated. The Wetherstones Basin covers more than five square kilometres in areal extent. There is no modern exploration record of the majority of this area, leaving open the prospect of the discovery of additional gutters, and primary mineralisation in the underlying schist.   Australasia Gold Ltd has embarked on a program to reassess the potential resources of the Wetherstones gold mineralisation, and to evaluate the feasibility of mining.

Jan 1, 2004

B. S. Crocker (Screened Ore Used for Fine Grinding at Lake Shore Mines, P. 499) was born in Toronto, Ont. and attended Saint Andrews College and University of Toronto. He received a B.A. and M.A. degree. He was graduated with honors and received a fellowship in metallurgy. Mr. Crocker did post-graduate research at University of Toronto from 1933 to 1934. He was employed by Beattie Gold Mines in 1933. He did research in milling at Lake Shore Mines from 1934 to 1936 and from 1936 to 1940 was head of experiment laboratory. At the present time he is mill superintendent with Lake Shore Mines at Kirkland Lake, Ont., Canada. Grinding, cyanidation, flotation and roasting are of special interest to him. He is a member of AIME. Mr. Crocker has presented several papers before C.I.M.M. and also holds membership in this society as well as Professional Engineers of Ontario. Skiing, yacht racing and photography are his favorite hobbies.

Jan 1, 1952