Search Documents

By Martin T. Broome

INTRODUCTION The Luanshya Mine is situated in the southern part of the Zambian Copperbelt. The copper ore deposit is stratiform, and is preserved in a synclinorium known as the Roan/ Muliashi basin. Roan shaft (formally called No.14 shaft) is located at the eastern end of the syncline and is theoldest of the presently operating hoisting shafts, being sunk during the 1930's. It presently hoists some 45 per- cent of the total Luanshya Mine production. A cross-section through the shaft is shown in figure 1. The ore formation on the south limb is unmined on this section because until recently it was believed that such mining might cause damage to the shaft. This paper examines the influences of adjacent mining on this so-called 'shaft pillar', and describes the mechanics of subsidence of the pillar itself. GEOLOGY AND STRUCTURE Figure 1 shows the general form of folding in the vicinity of Roan shaft. The north and south limbs of the main syncline approach parallelism, with the bottom of the trough fairly smoothly rounded. The axis of the - trough plunges to the west-north-west at 6° - l0°. A brief summary of the major lithologies present in the Roan basin is given in table 1, however, the performance of the overall structure during progressive mining of the ore horizon is controlled by the following features in addition to the mining method. Intraformational Contacts These are characteristically weak in most geological environments. The BC/RL7 contact is an unconformity between moderately weak quartz-biotite schists below (unconfined compressive strength 40 - 80 MN/M 2), and strong quartzites above (U .C .S. 170-200 MN/M2) Subsequent formations are conformable, and planes of weakness are generally the result of contrasting lithology (see below). Weak Interbeds The Rt7, RL6, RL5, RL3 and RU2 horizons consist predominantly of quartzitic rocks, i.e. conglomerates, quartzites and argillites, and as such are generally strong and considered suitable for the positioning of development. Between these however, lie two much weaker dolomitic horizons, the RL4 and RU1. The Rt4 is the main hangingwall aquifer, and must be drained prior to mining. Drainage results in an extremely weak, blocky cavernous horizon which usually requires support if exposed by development. Similarly, the RU1 formation is comprised mainly of dolomites and dolomitic arqillites which are weak and cavernous. In the eastern part of the Roan/

Jan 1, 1981

By George W. Hezzelwood

THE Balatoc mine, one of the Haussermann group,† is on the Island of Luzon, the largest of the Philippine group, about 260 km north of Manila, and 12 km from the city of Baguio The Baguio district is the most important gold-mining area of the Philippines, with 14 producing mines in 1939, milling 2,358,804 tons of ore, yielding [P]40,881,048, approximately 55 per cent of the total Philippine production of [P]74,131,216 PRODUCTION HISTORY The Balatoc mine began production In January 1929 with a 150-ton cyanide mill Increases in mill capacity have taken place as follows March, 1932, to 330 tons June, 1933, to 470 tons December, 1933, to ;15 tons July, 1934, to 700 tons December, 1934, to loon tons May, 193, to 1200 tons October, 1938, to 1300 tolls April, 1939, to 2000 tons January, 1941, to 2T50 tons Production during the period of expansion has steadily increased in total value in spite of the fact that grade of ore milled has dropped-from $31 06 in 1929 to $5 78 in1940 Annual reports give production as shown in Table I, the average value, being based on gold at the old price of $20 67 per ounce [ ] GEOLOGY The ore occurs in quartz-calcite veins that vary in width from narrow stringers to mineralized zones 40 to 30 ft wide Wall rocks consist largely of diorites, with some andesite, and a fragmental breccia called locally the "Balatoc plug " Texture of the ore varies widely in the different vents-from a soft, highly altered, gouge material filled with quartz fragments through a soft, unaltered quartz-calcite to a hard, massive quartz ore Three major vein systems have been extensively developed, and smaller amounts of work have been done on several others These veins strike east-west to N 60°, clipping south from 50° to 90°, and are essentially tension breaks between a series of faults or shears striking N 30°E to N 30°E and clipping southeast from 50° to 90° The shear veins and tension veins probably formed more or less simultaneously,

Jan 1, 1942

By J. Roger Loebenstein

ASARCO Incorporated, the only domestic arsenic producer, terminated copper-smelting operations and the associated recovery of byproduct arsenic trioxide at Tacoma, W A. in 1985. It still shipped small quantities of trioxide from its remaining stocks in 1987. Imports for consumption of arsenic trioxide were slightly higher than in 1986. Domestic Data Coverage.-Shipments of small amounts of arsenic trioxide from remaining stocks by Asarco were reported voluntarily to the Bureau of Mines.

Jan 1, 1989

Etching solutions containing hexavalent chromium ions (e.g., chromic acid) are used in brass finishing, printed circuit board etching, preparation of plastic for plating, anodizing, and various other industrial surface treatment operations. As the solutions are used, hexavalent chromium ions are reduced to their trivalent state, contaminants accumulate in the solution, and the effective acid concentration is reduced. When the etching rate becomes unsatisfactory for the particular operation, the solutions are discarded. This is a problem because the discarded solutions are pollutants, and because replacing the etching solution is expensive. The Bureau of Mines has developed a process for regenerating these spent solutions and returning them to the surface treatment operation without interrupting the etching process. An electrolysis cell containing anode and cathode compartments that are separated by permeable membranes, is used for regenerating the spent solutions. The spent chromic acid solution is fed to the anode compartment and sui (uric acid is circulated in the cathode compartment. Application of a steady electrical potential of a few volts dc across the electrodes causes the copper ions and other contaminants in the spent solution to migrate through the membrane to the cathode compartment where copper is plated onto the cathode. Zinc and the other contaminants remain in the sulfuric acid. At the same time, the complex, trivalent chromium ions in the spent solution are attracted to the anode where they are oxidized to their original hexavalent state. The regenerated solution in the anode compartment is then recycled back to the plant?s etching operation for reuse.

Jan 1, 1980

By S. R. Droes

The U.S. Bureau of Mines investigated calcium fluoride (CaF2) assisted sulfuric acid (H2S04) leaching as an alternative to the melting-quenching procedure to obtain Mn from domestic manganese silicate resources. Pyroxmangite [(Mn, Fe) Si03] ore containing, in percent, 34.4 Mn, 22.8 Si, 2.6 Ca, and 1.3 Fe was leached in a 500-mL resin kettle. Ninety-six percent of the Mn was extracted under conditions of 330 g/L ore, 245 g/L H2S04, 35 g/L CaF2, 90' C, and 2 h. To incorporate electrowinning in recovering Mn, the ore was leached with a simulated spent anolyte solution containing, in grams per liter, 12 Mn, 140 H2S04, 130 (NH4)2S04 (ammonium sulfate), and 5 CaF2. Manganese extraction of 92 pct was achieved from 130 giL ore leached at 90° C in 3 h. The Fe, silica (SiOJ, and other impurities were precipitated from the pregnant solution by neutralization with ammonia (NH3). Manganese of greater than 99-pct purity was deposited at a cathode current density of 50 mA/ cm2 at 30° C, with a current efficiency of 65 pet in a two-compartment cell. A flowsheet was proposed for the leaching and electrowinning procedure.

Jan 1, 1990

By B. J. Bayles, J. A. Ford, M. J. Salkind

Unidirecltonally sulidijied AL-A13Ni was found to exliibit excellent microstructural stability to 508°C. Above this temperature the transverse micvostructure coarsened in a manner analogous to "Ostwald Ripening", but the A13Ni whiskers did not spheroidize or foreshorlen. The coarsened whiskers reinforced the matrix as effectirely as the finer whiskevs and no reduction in room-temperature tensile strength mas noled after exposure for 90 hr at 96 pel 0-1 the absollite melling temperature of the eulectic. The slability was auribucted to the presence of low-index (and presurrlably lor-energy) cvystallographic interjaces between phases. The driving force for microstructural coursening was presumed to be the reduction of interfacial energy between the phases. Finer micvoslructures were found to coarsen more rapidly than those which weve imitally coarser. FIBER-reinforced metals have been shown to exhibit good short-time tensile properties at elevated temperatures.1-4 However, many elevated-temperature applications require long-time property retention which dictates the necessity for microstructural stability. Two types of instability are common to fiber composities. The first, chemical instability, is due to chemical reaction between the matrix and the relnforcing phase. Petrasek and weeton5 have shown that chemical reaction between tungsten wire and several copper alloy matrices resulted in degradation of the reinforcing phase and reduction in strength of the composite materials. Kreider and Leverant4 have noted similar behavior for boron-reinforced aluminum above 400°C. The second type of instability arises in systems in which the phases are essentially chemically stable with respect to each other and is characterized by spheroidization and/or agglomeration of the reinforcing phase. parratt6 has reported this type of degradation to occur relatively rapidly at moderate temperatures for nickel and cobalt alloys containing whiskers of silicon nitride, aluminum oxide, and silicon carbide and has identified it as "physicochemical" instability. Although both types of instability are the result of the differences in the chemical potential between the fibrous phase and the matrix, they may be differentiated by the fact that the second type, "physicochemi-call' instability, results in little or no net change in the composition or amount of each phase present. It does, however, result in a morphological change which profoundly affects the strengthening mechanism. Chemical interaction. on the other hand, results in a change in the composition and amount of one or more of the phases present, or the appearance of a new phase. In the latter case, the appearance of the mi-crostructure, that of a fibrous phase aligned in a matrix, may remain essentially unchanged, but the chemical degradation of the fiber results in markedly reduced composite strength. This investigation was initiated in an attempt to evaluate the microstructural and related mechanical property changes of a whisker-reinforced eutectic composite after elevated-temperature exposure. The composite system chosen for this study was the uni-directionally solidified A1-A13Ni eutectic which Lemkey. Hertzberg, and Ford7,8 demonstrated to behave as a whisker-reinforced composite. The microstructure of the unidirectionally solidified material consists of aligned needles of A13Ni in a matrix of aluminum. EXPERIMENTAL PROCEDURE Eutectic ingots having a nominal composition of 6.2 wt pct Ni were produced by melting 99.99+ pct A1 and 99.99 pct Ni in recrystallized alumina crucibles in an argon atmosphere. The analyses of the starting materials are listed in Table I. These master heats were cut up? melted by induction heating, and unidirectionally solidified vertically in 1/2 -in.-ID. 6-in.-long graphite crucibles, in a dynamic argon atmosphere. Therma1 gradients in the liquid were determined by measuring the temperature in the melt as a function of apparatus travel distance, as discussed by Kraft and Albright.9 The rate of solidification was assumed to be equal to the uniform rate at which the crucible assembly was withdrawn from the furnace. Ingots representative of nominal growth rates of 2, 5, and 11 cm per hr were produced and the solidification parameters are summarized in Table 11. Ingots used for met allographic analysis were pre-

Jan 1, 1968

By P. Taskinen, A. Jokilaakso

The Flash Smelting Process for copper and nickel production has been one of the most successful new metallurgical process developments in the 20th century. The experimental data from laboratory scale investigations of studies has produced information and insight into the reaction mechanisms and kinetics of the flash reactions of copper concentrates. Advanced computer models coupling chemical reactions with a Computational Fluid Dynamics (CFD) software became possible with the development of commercial CFD software together with increased computing power. Currently, there are both experimental and CFD modelling, including also CFD–DEM coupling (Discrete Element Method), studies ongoing for investigating the kinetics of matte – slag reactions in the flash smelting furnace (FSF) settler. The ultimate goal of the modelling work is to develop a comprehensive FSF model for studying the behavior of changing raw materials, both primary and secondary, and distribution of their elements between the matte, slag, and gas phases. The use of User-Defined-Functions (UDF) is one way to digitalize metallurgical knowledge and experimental information to be used for supporting process experts and development of artificial intelligence applications in metallurgy. In this paper, a review of the development of the FSF reaction shaft modelling and experimental investigations, and the current work for the settler reactions’ experiments and modelling are presented. INTRODUCTION The Outotec Flash Smelting process (Bryk, Ryselin, Honkasalo, & Malmström 1958) has been used in the copper and nickel industry for 70 years with continuous support from experimental investigations by many research groups in academia, among others Jorgensen and Segnit (1977); Jokilaakso, Suominen, Taskinen and Lilius (1991), Chaubal and Sohn (1986), Kim and Themelis (1986), and in industry Mäkinen and Jåfs (1982); Kojo, Lahtinen and Miettinen (2009); Tuominen, Pienimäki and Fagerlund (2016). It has been developed also for pyrite and lead smelting (Asteljoki, Sulanto & Talonen, 1984). A schematic illustration of the FSF and other main parts of the process is depicted in Figure 1. Also, two and three dimensional physical water or gas models have extensively been used in product and process development (Lilja & Rajainmäki 1995). During the recent decades, computer based models have increasingly been adopted in the FSF research and development (Ahokainen & Jokilaakso, 1998); Ahokainen, Jokilaakso, Taskinen & Kytö, 2006; Hahn & Sohn, 1990; Jorgensen & Elliot, 1992; Zhou, Zhou, Chen & Mao, 2014; White, Haywood, Ranasinghe & Chen, 2015) to name a few, but also in supporting engineering and sales of the technology (Miettinen 2017). Even though the reactions of the sulfidic concentrate particles have been included in the reaction shaft modelling, the complete FSF model with both gas-solid/drop and molten slag/matte drop has so far been and still is too demanding for today’s computer hardware.

Jan 1, 2019

By H. Tanner, T. Heikkinen

In1950 studies concerning mining and milling of the approximately 17 million tons of ore remaining at Outokumpu revealed the surface facilities for economical treatment were inadequate. The two shafts would soon be too far from the mine workings. Moreover, in spite of several extensions, mill capacity was insufficient and recoveries were not satisfactory. Therefore it was decided in 1951 to sink a new shaft and to build a new mill and auxiliary surface buildings around the shaft. The new shaft was sunk near the center of the remaining orebody, about 650 ft from the ore to the footwall side. This location placed the main part of the shaft as well as the crusher rooms and the ore bins around the lower end of the shaft in the firm and strong mica-schist.

Jul 1, 1955

By G. C. Gester

Oil has been produced in Persia and India for many years, but it was not until 1932 that Arabia entered the arena as a potential oil-producing area. In 1930 the Standard Oil Co. of California acquired a concession covering the rights of exploration and exploitation for oil in the Bahrein Islands and in June, 1932, the first commercial production was discovered by the bringing in of a well known as Jebel Dukhan No. 1 on the Island of Bahrein. Since then the Standard Oil Co. of California through its wholly owned subsidiary, The Bahrein Petroleum Co. Ltd., has been carrying on a systematic survey and development program of its concession in the Bahrein Islands. This group of islands, of which Bahrein is the largest, is in the southwestern portion of the Persian Gulf, approximately 25 miles from the mainland of Arabia. Although geographically a part of Arabia, the islands are not a part of the Kingdom of Saudi Arabia. Their government is essentially independent but certain special rights have been granted to Great Britain through a series of treaties. The Island of Bahrein is 32 miles long by 9 1/2 miles wide and covers an area of 215 square miles. Approximately three-fourths of the island is occupied by a relatively low, broad, elliptically shaped dissected hill, the central part of which is slightly depressed with inward-facing cliffs but culminating in the Jebel Dukhan (Hill of Smoke), which rises to an elevation of 443 ft. above sea level. The topography of the island is a good index of its geologic structure. Structurally the island is an elongated dome or quaquaversal fold composed of rocks of Eocene age. The major axis of the fold strikes N.5W. All of the topographic high portion of the island is a part of the structural uplift. The crest of the fold is broad and flat with the dips increasing on the flanks. How far tilted strata may continue beyond the line where the Eocene beds are covered by recent sands and detrital material is not known. Superimposed on the general structure are a few small irregularities in the form of minor folding and faulting. There is, however, no evidence of any major faults. The largest of the irregularities lies to the south of Jebel Dukhan and has the appearance of a sink

Jan 1, 1934

By C. R. Kuzell

IN COMPARISON with recent years 1932 has yielded much less tangible evidence of progress in copper reduction and refining. The industry has been extremely quiet, especially in the United States. Design and construction has been throttled by lack of new capital expenditures. The excess producing capacity of the whole industry and the extremely gloomy outlook for the future have made it unwise to tie up more capital except under special conditions. The plants built during the previous year have, however, been placed in operation. Older plants have been abandoned, temporarily shut down, placed on part time operating basis, or continue to operate at a low percentage of normal capacity. In the United States the Phelps Dodge Corporation at Douglas, Ariz., has completed the remodeling of the former Calumet & Arizona smelter. A new roaster and Cottrell plant chimney was completed this year. Though operations have been limited the new equipment has been found to justify all expectations. The reverberatory plant addition consists of two furnaces 26 by 107 ft. inside dimensions, with a high arch, and modern steel binding of excellent design. Natural gas fuel gives good results. One of these furnaces will treat 1000 tons of solid charge per day with a fuel consumption of approximately 3,000,000 B.t.u. per ton. The larger converters have not only yielded the expected lower costs, but have simplified operations in the converter department. One of the noticeable results is the greater cleanliness in the environment and the absence

Jan 1, 1933

By G. Van Esbroeck, M. Van Weyenbergh

The copper mines of the Katanga region in the Belgian Congo lie along the same mineralized belt as those of Northern Rhodesia. There are two distinct types of deposits in that belt, the dolomitic and the quartzitic. In the dolomitic type the metallic minerals are found in a dolomitic limestone country rock. Through oxidation and enrichment, large deposits of high-grade oxidized copper ores were formed, some of which are being worked by the Union Minière du Haut Katanga. Such deposits are all in Katanga. The quartzitic deposits are found in Katanga and Northern Rhodesia. Here the primary mineralization occurred in sandstones and quartzites, in horizons stratigraphically lower than the dolomites. These rocks are not favorable to secondary enrichment and the oxidized zone is poorer than the sulphide zone, which alone contains the ore. There are also in Katanga a few ore-bearing veins. One of them is being worked in the Prince Leopold mine at Kipushi. Prince Leopold Mine The Kipushi ore body fills a fault vein and invades the wall rocks more or less extensively by metasomatic replacement. The vein strikes north-northeast and south-southwest and dips to the west. The variable dip averages 60' to a depth of 300 ft., and more uniformly 80' below 400 ft. In the upper section the average width is 200 ft. and below the width is about 150 ft. The length of the ore body is 2300 feet. The eastern side of the vein—the footwall—is dolomitic and contains irregular masses of ore sometimes extending 100 ft. or more from the main

Jan 1, 1940

By M. Van Weyenbergh, G. Van Esbroeck

The copper mines of the Katanga region in the Belgian Congo lie along the same mineralized belt as those of Northern Rhodesia. There are two distinct types of deposits in that belt, the dolomitic and the quartzitic. In the dolomitic type the metallic minerals are found in a dolomitic limestone country rock. Through oxidation and enrichment, large deposits of high-grade oxidized copper ores were formed, some of which are being worked by the Union Minière du Haut Katanga. Such deposits are all in Katanga. The quartzitic deposits are found in Katanga and Northern Rhodesia. Here the primary mineralization occurred in sandstones and quartzites, in horizons stratigraphically lower than the dolomites. These rocks are not favorable to secondary enrichment and the oxidized zone is poorer than the sulphide zone, which alone contains the ore. There are also in Katanga a few ore-bearing veins. One of them is being worked in the Prince Leopold mine at Kipushi. Prince Leopold Mine The Kipushi ore body fills a fault vein and invades the wall rocks more or less extensively by metasomatic replacement. The vein strikes north-northeast and south-southwest and dips to the west. The variable dip averages 60' to a depth of 300 ft., and more uniformly 80' below 400 ft. In the upper section the average width is 200 ft. and below the width is about 150 ft. The length of the ore body is 2300 feet. The eastern side of the vein—the footwall—is dolomitic and contains irregular masses of ore sometimes extending 100 ft. or more from the main

Jan 1, 1940

By G. Goodall, M. Muinonen, R. Pandher, R. Jabbar, S. J. Muinonen

"The implementation of a new and highly efficient converting practice at the Glencore Sudbury Integrated Nickel Operations Smelter has opened the possibility to further capacity increases by using larger ladles. To quantify the impact of increasing ladle sizes from 200 to 300 ft3, XPS constructed a detailed discrete event simulation using the commercial software package Rockwell Arena®. The challenges associated with implementing a model on an intricate and tightly scheduled process, and the solutions needed to derive meaningful results will be presented. The aisle capacity is predicted to increase by approximately 17 %, with a reduction in furnace tapping demand of 8 %. Arena modeling capabilities and the key factors contributing to the overall capacity increase at the Sudbury INO Smelter will be reviewed and presented.INTRODUCTION The Glencore Sudbury Integrated Nickel Operations (INO) comprises two Ni-Cu-PGM mines, Strathcona Mill, and the Sudbury Smelter. The Smelter has operated continuously since 1929 using different processes to produce nickel-copper Bessemer matte. Feeds to the Sudbury INO Smelter are a blend of concentrate from Strathcona Mill, Raglan concentrate produced at the mine-mill complex in Raglan, Quebec, as well as third party concentrate feeds shipped to Sudbury from around the world. In 2016, the Sudbury INO Smelter produced 75,900 tonnes of nickel and 20,000 tonnes of copper in Bessemer matte. The product matte is shipped to Glencore’s Nikkelverk refinery in Kristiansand, Norway where it is refined to produce nickel and copper cathode. A schematic of the Sudbury INO Smelter’s flowsheet is shown in Figure 1."

Jan 1, 2017

By S. J. Czehura

The Butte quartz monzonite is the host rock for early porphyry copper style mineralization and subsequent mesothermal-epithermal, enargite-gold style veining that transects the district. The east-west Anaconda system veins: including the Emma, Anaconda-Original, Syndicate, Badger-State, and Alice-Rainbow veins, each with strike lengths of over 12,000 feet and vertical continuity in excess of 4,500 feet, along with mining widths from 5 to 50 feet, are unique to Butte. The incredible dimensions and tenor of these veins have yet to be surpassed and Butte is still touted as being the “Richest Hill on Earth.” The Anaconda Company was formed in 1895 to develop underground copper reserves in the district and eventually consolidated all operations under one company. Production from underground mining continued through the mid-1970’s. Open pit mining in the Berkeley pit began in 1955 with the extraction of supergene ores, along with the remnants of deeper horsetail zones inaccessible to the underground mines. Operations in the Berkeley pit were suspended in mid-1982 because of the rejection of high arsenic, copper concentrates at major smelting facilities throughout the world. Bulk mining of porphyry style mineralization in the Continental pit began in January 1980 to supplement copper production while stripping “C” pushback in the Berkeley pit. The Anaconda Smelter closed in September 1980. A molybdenum circuit was added to the Butte Concentrator in 1981 and mining continued in the Continental pit to produce copper and molybdenum concentrates. A blend of Berkeley and Continental ores were processed to dilute penalty metals in the final concentrates marketed to toll smelters. All mining operations ceased mid-1983 when Anaconda closed the Continental pit and offered the property for sale. Montana Resources reopened the Continental pit in June 1986 to produce copper and molybdenum concentrates. Operations were suspended mid-2000, because of exorbitantly high power prices, but resumed in November 2003 with rising metal prices. Bulk open pit mining of the early porphyry style mineralization has sustained production over the past twenty years and mining is expected to continue in the Continental pit with favorable prices. Future mining will eventually develop a 500 million-ton geologic resource incorporated in a supergene enrichment blanket situated between the Berkeley pit and the Continental pit. Grades in this enrichment blanket range in the neighborhood of 0.5% copper.

Jan 1, 2006

The only good news in the exploration sector in 1982-a year plagued by low metal prices and weak demand-was precious metals. Gold in particular remained in the forefront, as it has for at least the past three years. The reason for this is partially due to gold's seeming resilience to conventional supply side factors-such as new production-that normally influence many other metals. Also, with projected production costs of about $6.40-$9.65/g ($200¬$300/oz), modest deposits with average grades can offer an early return on capital investment and good profit potential. Keeping escalating capital costs for new mining ventures within reason has shifted gold exploration efforts in recent years. Many mining companies are seeking relatively low grade, modest tonnage, near-surface gold mineralization. This, of course, leads to lower development costs using open-pit mining methods. Recent refinements in the carbon-in-pulp recovery process also has enhanced the economics of such deposits. Slumping economic conditions certainly played a key role in shaping exploration activity last year. Nearly every major mineral-producing state recorded exploration slowdowns. In Alaska, for example, development expenditures approached the level of exploration spending for the first time in the state's history. This not only reflects major companies' decisions to move toward production but also the economic slowdown. The worldwide recession stopped Nevada's exploration and mining boom "dead in its tracks," said John Schilling, state geologist. The year was one of layoffs and closings for the state's mines and exploration offices, he reported. Similar trends were noted in most other states, especially in the West and Southwest. In the Pacific Northwest, however, exploration appeared to continue at a relatively good pace considering the metals market. In the mining geophysical community, recent advances in telecommunications and microprocessor technology are continuing to provide a positive impact. Many geophysicists have begun using satellite digital communication links to access computer systems from remote sites where using a microcomputer would be difficult. There were also major contributions made in exploration geochemistry last year. Highlights include progress in formulating mineral deposit models, geochemical exploration in glaciated and arid environments, and publication of many informative books. The following state-by-state summary and articles on geophysics and geochemistry provides a detailed view of exploration events throughout the US in 1982.

Jan 5, 1983

By H Han, d S. Hapugoda, L Lu

With the recent rapid development of Chinese steel industry, the world iron ore resources of good quality are depleting rapidly. As a result, iron ore deposits of lower quality have been or are being developed to meet the market demand and are becoming increasingly important to iron and steel companies. As concentrates have advantages of high Fe grade and less harmful impurities, they are ideal sweeteners to maintain sinter grade and quality when high proportions of low-grade ores are used in the sinter blends. However, due to their fine nature, addition of concentrates will inevitably increase the proportion of adhering fines and reduced the proportion of nucleus particles of the sinter blends, which can adversely affect the green bed permeability and sintering productivity. In the present study, lab scale sintering tests were carried out under the conditions similar to the sintering process to examine the effect of concentrates on the high temperature sintering characteristics of sinter blends and the structure and strength of the resultant sinter analogues.

Sep 18, 2023

By E. H. Griswold, W. J. Wilkins

Pressure control of oil wells may be defined as the adjustment of pressures within a well to obtain the most efficient and economic utilization of the natural gas energy with a minimum of sand troubles or irregular water encroachment. The purpose of this paper is to present the methods used by the writers in applying pressure control and a discussion of the various effects occurring within the wells affected. The benefits to be derived from the conservation of natural gas energy have been so adequately discussed and demonstrated in prior papers by various engineers that the effects on ultimate production will not be discussed other than to mention a few representative cases. The detrimental effects of irregular edge-water encroachment and of sanding up arc of general knowledge to the industry. Effect on Ultimate Production One of the strongest objections voiced against pressure control is that of the danger or inadvisability of deferring oil production by cutting the rate of production. It has been our experience that such deferred product'ion is returned within a few weeks or months rather than years and that an increased cumulative oil production is obtained in the early life of the well by conserving the natural energy. In many cases the rate of production is increased rather than decreased by the adjustment of pressures to obtain the minimum gas factor. Fig. 1 shows the history of a Wilcox sand well in northern Oklahoma, which was pressure-controlled from completion. It is noted that during the early months while flowing naturally through the casing the gas factor was decreased rather than allowed to follow its natural tendency to increase. A string of 21/2-in. tubing was run to restrict the flow and resulted in a decreased gas factor with a more sustained rate of production. When first placed on gas-lift the gas factor again tended to increase, but after the proper pressure adjustments were made, remained approximately steady. It was necessary to defer 100 bbl. per day of oil production in order to maintain this low gas factor. In March serious

Jan 1, 1929

By Waller M. D, Whittaker B. N, Singh R. N

This paper overviews the recent research progress in predicting cutting performance using fracture mechanics principles. It is emphasised that rock fragmentation due to cutting is mainly a process of chip formation resulting from crack initiation and propagation or crack interaction for multi-tool cutting. This process can be simulated by using the well developed fracture mechanics criteria coupled to numerical methods. Fracture toughness is shown to be an important and useful parameter in quantifying cutting performance and in designing cutting tools. The paper concludes with discussions on the dynamic effects involved in rock cutting processes which should be taken into account for optimum cutting efficiency and tool design.

Jan 1, 1992

By R. J. Pruett, P. I. Prescott

Ground calcium carbonate (GCC) is used in the paper, plastics, paint, rubber and caulks and sealants industries. The favorable properties of GCC include high whiteness and brightness, low hardness and outstanding rheology in water systems. The quality of calcitic GCC ores, which includes chalk, limestone and marble, is dependent on calcite purity and the nature and quantity of the impurity minerals. Wet and dry grinding are used in the processing of GCC. Ore processed by optical sorting, flotation and/or particle-size classification has higher brightness and lower abrasion characteristics. GCC markets are a function of the product's properties, purity and cost.

Jan 1, 1997

By R. M. Wheeler

For years the blasting industry has recognized eight milliseconds as the minimum delay time interval required between charges in order for them to be considered to fire independently of each other. However, computer analyses of seismic recordings made of several surface mine blasts reveals that this time interval may not always be sufficient for adequate vibration separation to occur. In some situations a combination of short delay periods and low frequency vibrations can result in waveform reinforcement. Various analyses of seismic recordings obtained from single hole detonations can be used to predict delay intervals that may enhance or reduce blast vibration effects.

Jan 1, 1987