Search Documents

By C. L. Pillar

INTRODUCTION The location, size, character of the ore de- posit and its adjacent formations will deter- mine the mining system best used for its ex- traction. The mining system chosen will have to be engineered to suit the ore deposit and the people that will extract it. What can be done in the Philippines cannot always be accomplished in the upper Northwest Territory of Canada. Mining operations developed under a free enterprise system are planned to achieve a satisfactory return on the capital required to place them into production. Hence, the choices made in planning and developing the mining system must be dictated by sound economics. The mining system planned must favor: 1. Maximum ore extraction of the deposit with minimal grade dilution. 2. The amount of capital expenditure used to develop and equip the mine must be in harmony with the financial policy of the group yet be sufficient to provide a reliable mining system. Excessive frills and extras that are not required for efficient, safe production should not be provided. 3. Mine production costs are determined by the amount of men, material, equipment and energy used in the production process. These must be kept to minimal limits in order to insure dependable, low cost production. Extras that later are needed in the production operation can be added as required by the operator. Basically block caving is a mining system that is normally used to extract deep seated, massive, low grade deposits of copper, molybdenum and iron where stripping ratios for open cast mining are economically prohibited. The caving system is limited in its selectivity. It is a mass production type of underground ore extraction that under favorable conditions is one of the most efficient, low cost mining systems in the world today. Usually block cave mining systems are large. They are capable of producing ore at a rate of 10,000 to 100,000 tons/day from large deposits at costs that are comparable with many open cast mining systems burdened by high waste to ore ratios. Block cave mining systems differ basically in the plan of the area layout, the method of undercutting and the method of draw. The balance of the mining system is the mechanical transportation of the drawn ore to the surface, the mine supply, drainage and ventilation systems. This paper deals mainly with the methods of draw. The method of draw to be used in a block caving system dictates the development plan of the mining area, is highly influential in the method of undercutting to be employed and the supply and ventilation system to be used. There are three basic methods of draw commonly used in today's operations. They are: Gravity draw Slusher draw LHD draw The type of draw planned will have a major affect on: Capital expenditure and time required to bring a deposit into production. Productivity, efficiency and cost of the production operation. Percent recovery of the ore deposit in both tonnage and grade. Degree of production reliability Fundamentally the type-of draw used must be compatible with the physical characteristics of the deposit to be extracted and the financial position of the mining operation. The type of draw chosen must work to advantage with the size, configuration, depth, strength and fracture pattern of the deposit and its adjacent formations. It must favor the financial protection of the planned mining operation. A Gravity Method of Draw requires a finely fragmented, easy flowing product from the caving action of the deposit. To obtain the desired economic advantage the ore deposit must also have sufficient area and height of column to permit minimal development cost on a per ton basis. The gravity system re- quires the maximum amount of development openings and uses the minimum amount of mechanized equipment of all the caving systems. It is unskilled, labor-intensive and is highly sensitive to size of ore fragmen-

Jan 1, 1981

By J. A. Woolf, E. S. Leaver

"So much has been written on the ore genesis of the Comstock Lode that it is sufficient here to describe the original ores as consisting chiefly of quartz and some calcite. In places .a considerable amount of pyrite appears. There are also minor amounts of galena, chalcopyrite, and sphalerite. The chief silver minerals are argentite, stephanite, and polybasite. Most of the gold is native.A composite analysis of the ore; obtained by averaging the results from the early workings of several mines, is shown in Table 1.The history of the milling of Comstock ores from the Sixties to date would call for a review of the development of precious-metal metallurgy. However, a brief outline of the methods employed will give a better basis for studying the difficulties that are to be expected in the final retreatment of the remaining residues.In the earliest days amalgamation was accepted as the main recovery method. The large tonnage of good-grade ore from the Comstock Lode attracted the best metal¬lurgical talent of the time, and developed there the highest skill in the art of amalgamation, including the auxiliary chemical preparation of the ores and the mechanical operation. In this work 0.5 to 6.0 pounds of mercury was used per ton of ore. The mercury loss probably averaged about 2.5 pounds per ton of ore treated.The better grade of tailings from the ores milled were impounded, often near the works. In many cases the same tailings were reworked several times before they entered the main outflow waste stream that had its course down Seven Mile Canyon to the Carson River. Following the water course down the canyon the tailings were re-impounded, and, as metallurgy advanced, new plants were erected to again re-treat them. The most successful of these plants used forms of amalgamation, chlorination, and cyanide methods of recovery. To the tailings from the re-treatment plants, smaller tonnages of untreated tailings produced by milling lower-grade ore are continually added.Along the stream bed down the canyon a series of blanket runways were constructed, and each was independently operated for years by one or more men. All, or the heavier portion of the stream flow was run over the blankets; in this way much of the heavier concentrate, mostly sulphides and mercury products, was reclaimed.All of the residues finally entered the run-off flow along with the sewage from Virginia City and waste from the gas works, saw mills, and stables. As the accumulation along the bed of the Carson River became a nuisance, the lighter and better grade of tailings was impounded on the banks of the river. This accounts for the large dumps locally known as ""Douglas tailings."""

Jul 1, 1928

By N. Arbiter

Evidence for the floatability of sulphide minerals without collector is analyzed and it is shown that results obtained with ores, in contrast to those with single minerals or mineral mixtures, depend on many additional variables, some identified and others not. Because of the prevailing low levels and costs of collectors for most sulphide ores, it is unlikely that collectorless flotation will have commercial applications, so that continued research on the subject may be justifiable on theoretical but not on practical grounds.

Jan 1, 1993

By M. S. Burton, J. E. Ritter

The sessile-drop technique was employed to study the effect of atmosphere and alloy additions of titanium and chromium on the surface tension and contact angle of nickel on sapphire substrates at 1500oC. Shear tests were conducted on the solidified sessile drops. The liquid-gas surface tension of pure nickel on sapphire was found to be 1747 ergs per sq cm, with a contact angle of 109.6 deg. The surface tension and contact angle were not affected significantly by the four atmospheres, vacuum, impure argon, pure argon, and pure hydrogen. Small additions of titanium and chromium decreased the contact angle and for the same alloy content, contact angles were lower in pure argon than in pure hydrogen. On the basis of shear-test results , the most probable cause for adhesion in the Ni-Al2O system is the formation of NiO:Al2O3 spinel at the interface; in the titanium alloy-Al2O3 system adhesion is thought to be due to a mechanical interlocking effect; in the chromium alloy-Al2O3 system adhesion is believed to be the result of solid-solution formation involving Cr2O3 and Al2O3 at the interface. In the last few years there has been considerable interest in reinforcing metals with ceramic whiskers. It has been postulated that, by reinforcing nickel with sapphire whiskers, high-temperature strengths su- perior to those of the best current nickel alloys can be achieved.' To fabricate a whisker-metal composite having optimum density and strength, understanding of wettability and adherence in the system is of prime importance. Although there has been some previous research in this a a need for further studies has been cited4-8 to understand better the effects of impurities, alloys additions, and atmosphere on the wetting and bonding of metals to metal oxides. The purpose of this research was to investigate the factors involved in the wetting and adherence of nickel/nickel alloys to sapphire (single-crystal a Al2O3). Sessile-drop experiments were conducted in vacuum, impure argon, pure argon, and pure hydrogen, to determine the effect of atmosphere on the contact angle of the metals on sapphire, and the liquid-gas surface tension of pure nickel. The solidified sessile drops were sheared from the sapphire substrate to measure the bond strength between the metal and ceramic. The alloy additions chosen were titanium and chromium since both enhance the wetting of nickel on sapphire.2, 3c Also, titanium is commonly used when brazing metal-to-ceramic seals to improve adherence. Since chromium forms an oxide that is completely soluble in sapphire, it was thought that the oxide could serve as a transition phase to promote bonding between the Ni-Cr alloy and sapphire. I) EXPERIMENTAL APPARATUS AND PROCEDURE The sessile-drop apparatus was a horizontal furnace, with an induction-heated, cylindrical molybdenum susceptor in a water-cooled Pyrex chamber. This apparatus was patterned after that of Williams and Nielsen.7 A flat Pyrex window at each end of the furnace allowed temperature measurements to be made at one

Jan 1, 1968

By J. B. Newsom

DURING July and August, 1931, the Bloomington Limestone Co.,. at Bloomington, Ind., ran a single wire saw on ledge No. 2 at Maple Hill quarry. The ledge was hard rock, much harder than the average Indiana limestone. It was opened at two ends for a depth of about 20 ft., leaving a 130-ft. section between. During the tests 21 cuts were made in this ledge, to an average depth of 10.42 ft., for a total effective cutting area 028,445 sq. ft. The actual area sawed was about 20 per cent higher, as we did not level down in the center, preferring to cut deeper on the ends. The various cuts were carefully, logged, and the results plotted. A study of these results is interesting, as it enables a forecast of probable future costs to be made, and also because it points out the limitations of wire saws, and the lines development should logically take. Some of the inferences to be drawn are discussed below. Best Length of Cut.-No. trouble was due to length of cut, except that we could not easily level down a long cut, and it is probable that longer cuts, say up to 200 f t., can be made. Obviously, longer cuts will result in a higher sawing rate, in square feet per hour if- they do not cause stoppages. Working Higher Ledges.-The cuts averaged 10.42 ft. high by 130 ft. long. A study of several logs indicated that during only about 15 per cent of the cutting time was the saw cutting to its full efficiency; that is, during about 85 per cent of the time the saw was bedding in at the ends and not cutting well in the center, or the ends were below the floor line and only part of the wire was doing effective cutting. This does not mean that the wire was cutting to only 15 per cent of its capacity, but it means that during about 85 per cent of the time part of the cutting was being wasted. If higher ledges had been worked, the wire would have cut to its full efficiency a large part of the time, as it would have had a greater distance; to saw after it had bedded in to the ledge before the ends went down below the floor level. The exact saving to be expected cannot be calcu-lated, but it would be large, if really high cuts were made.

Jan 1, 1932

By R. V. Colligan

[CONTENTS PACE Educating and Training Economic Geologists of the Future. By C. H. BEHRE, JR. (TP 2278, Min. Tech., Nov. 1948. Discussions by R. V. COLLIGAN and EVAN JUST) ....... I Mercury Industry in Italy. By EDWIN B. ECKEL. (TP 2292, Min. Tech., Jan. 1948. Discussion .............................. by C. N. SCHUETTE) 3 Chert in the Kingsport Formation at Mascot, Tennessee. By ARTHUR T. ALLEN. (TP 2299, ............... Min. Tech., Jan. 1948. Discussion by M. M. BUTLER) 5 Wall Rock Alteration at Butte, Montana. By RENO H. SALES and CHARLES MEYER. (TP 2400, Min. Tech., May 1948. Djscussions by C. D. HULIN, W. D. JOHNSTON, JR., and L. C. ................................... GRATON) 5] Educating and Training Economic Geologists of the Future R. V. COLLIGAN*-I can best illustrate my opinions by drafting another five year plan (Table 2). This plan is set up following the same stipulations outlined by Dr. Behre, namely: (I) the student is preparing himself for commercial work as a mining geologist; (2) he is attending an institution with a sufficiently broad curriculum (that is, engineering school and mining school as well as liberal arts college) to furnish the courses listed; and (3) he is not planning to continue his studies through to a doctor's degree before going into commercial work. A comparison of my study plan (Table 2) and that submitted by Dr. Behre (Table I) will at once point up the basic similarity, due to the obvious fact that there are so many essential courses which must be included in any outline of study. However, a more detailed analysis will show up certain differences, which, in fact, are only certain refinements on Dr. Behre's program. These I plan to discuss in order of their importance. The first and most important change is the addition of 12 hr of optional subjects, making a total of 24 hr of optional subjects as against a total of 12 hr under Dr. Behre's schedule. This of course entails the elimination of certain courses, which I shall discuss later. However, I wish to make it clear that I suggest eliminating these courses not because I feel that they are unnecessary, but rather because I feel the optional courses are more necessary to the complete education of the individual. I appreciate that Dr. Behre recognizes the importance of the cultural side of education, but I take issue with his thesis that the student will get it without credit and in his spare time. I do not think that the average college student, and certainly not the college freshman, is mature enough to know what he needs and where to get it in his spare time. I think it must be "spoon-fed"; he must be oriented through specific courses. University life (or should I say "college life") is too full of athletics, fraternity activities, dances, "bull sessions," and countless other enjoyable distractions, all of which contribute to the "full man." I fail to see how the average young American male can possibly sandwich in a necessary complement of "cultural activities" in his spare time. Since these latter activities do not fall within the pattern set by the "group," and show less promise of immediate return in enjoyment, or increased social status on the campus, they are bound to suffer in competition with the more popular, "group" activities. No doubt much of the criticism levelled against arts colleges, namely, that the cultural courses are useless, is well taken, for the culture

Jan 1, 1947

By B. F. Buie

For over 200 years meerschaum has been a significant item of trade between the Near East and countries to the west. Best-known for its use in making smoking pipes and cigar and cigarette holders, it is also used in making a variety of decorative and ornamental items. It is easily carved, and is given an attractive, lustrous finish by rubbing. No published specifications are known, but compact form, purity, uniform whiteness or light color, and uniform, porous texture appear to be requisites. Fig. I a shows the appearance of a piece of crude meerschaum from Turkey; Fig. lb a carved item; and Fig. lc, d, and e show the fibrous and porous texture as revealed by the scanning electron microscope. Neither a major industrial mineral nor a precious stone, meerschaum nevertheless holds a record of long-and continuing-association with art and personal affairs of man. It is also a mineral to which modem methods of exploration and production probably could be profitably applied. An interesting account of the preparation and use of meerschaum in the early part of this century is given by Sterrett (1907). Geology and Mining Mineralogy Meerschaum is recognized now to be the compact variety of sepiolite, the claylike variety of which is one of the minerals included in the chapter on clays. The word meerschaum, from the German meaning "sea foam," was in earlier times used synonymously with sepiolite, a word of Greek origin suggestive of the resemblance of the compact variety-then the only variety known-to cuttlefish bone. At one time meerschaum was used as the commercial name, and sepiolite for the scientific name. However, to think of meerschaum as the name by which sepiolite is known commercially is no longer valid, in view of the recent emergence of the earthy variety as a competitor of bentonite and other clay materials. Present tendency is to restrict the term meerschaum to the compact variety, and to use the term sepiolite as a more general name to include both the compact and earthy varieties. This is the terminology followed in this publication. Meerschaum typically is white to light gray, has a hardness of 2 to 2 ½ , conchoidal to irregular fracture, and specific gravity varying with porosity from about 2 to less than 1. The composition is somewhat variable,- but is near that determined by Schaller (1936) for sepiolite as 2MgO.3SiO2.4H2O. A more modern for mula based on X-ray determination of the crystal structure is given by Caillére and Henin (1961) as (Site) (Mg9)030(OH)6(0H2)46H20. The reason for the firm, compact nature of meerschaum, in contrast with the earthy variety of sepiolite, is not fully understood. It may be due to the presence of a very minor amount of some bonding material such as silica. Scanning electron microscope (SEM) photographs of a specimen from Turkey (Figs. lc-le) indicate that the meerschaum is composed predominantly, if not entirely, of crystalline fibers which merge into sheetlike forms in a complex, intertwined mass. Detailed X-ray and crystal structure data, as well as some data on thermal stability range, are given by Caillère and Hénin (1961) for the sepiolite family of minerals. Mode of Occurrence and Origin Most authors have attributed the origin of meerschaum to alteration of serpentine or other magnesian minerals. The occurrence in alluvium and other surficial deposits does not necessarily indicate that the alteration was supergene. In fact, hydrothermal origin appears more likely for some deposits, though not for all.

Jan 1, 1983

By A. E. Hunt

Over the past twenty-live years since large scale truck haulage in open-pit mining began, the periodic introduction of Larger capacity vehicles has provided increased productivity and reduced costs. WISEDA Ltd. has introduced a 220 ton capacity, two-axle rear dump, diesel-electric truck for the world-wide large open-pit mining industry. Design features and components selected in the development of this vehicle will be presented along with operating experience and a brief history of rear dump truck evolution.

Jan 1, 1983

By D. Sammut, F. Houllis, J-L. Huens, J. Moyes

The Intec Gold Process has been developed as a halide-based alternative for the recovery of gold from refractory sulphide deposits. The halide medium allows sulphide oxidation and gold extraction to be performed concurrently at moderate temperature and atmospheric pressure sourcing oxygen from direct air injection. The dissolved gold is loaded onto activated carbon and stripped in a conventional Zadra circuit. High gold extractions have been achieved from a range of refractory gold concentrates at laboratory scale, which has led to a continuous locked-cycle pilot plant program. The pilot plant operated at >99% availability, with a maximum of 96.5% gold extraction from a concentrate containing 58.6 g/t gold. >99% of the dissolved gold was loaded onto carbon at up to 1% w/w, with no loss of carbon activity detected over five loading/washing/elution cycles. This paper describes the process and presents both laboratory and pilot plant results as well as economic data from two costing studies.

Jan 1, 2005

By J. Marin, H. A. B. Wiseman

This paper presents results of an experimental study dealing with the plastic stress-strain relations of aluminum alloy 14s-T6 subjected to combined biaxial tension and compression stresses. Plastic stress-strain relations for both constant and various types of variable stress ratios were determined and a comparison made with the simple flow theory of plasticity. THIS investigation was undertaken for two main purposes: 1—to obtain plastic stress-strain relations for Alcoa 14s-T6 when subjected to various combinations of biaxial stresses, and 2—to determine the validity of the flow theory in predicting plastic stress-strain relations for combined stresses. The biaxial stresses used were tension combined with compression. These stresses were produced by subjecting a thin-walled tube to axial tension and torsion. Various types of combined stress conditions were investigated. To provide control test data and information on the influence of biaxial stresses on the strength, the usual constant stress ratio type tests were made. These tests showed that the biaxial yield strength agrees approximately with the distortion energy theory. However, the Prager semi-empirical theory agrees best with the test results. For these constant stress ratio tests the plastic stress-strain relations were found to agree approximately with the flow theory. (For constant stress ratio the flow and deformation type theories are identical.) In view of the fact that the constant stress ratio tests cannot distinguish between the flow and deformation theories, a number of variable and special biaxial stress tests were made. These tests showed that the flow theory is inadequate, since large differences exist between the experimental and theoretical results. Special tests were also conducted to check the validity of the isotropic yielding assumption. This assumption is made in the linear-type flow theory. In these tests specimens were loaded in tension to predetermined values beyond the proportional limit stress. The tension load was removed from the specimen and the specimen was subsequently loaded in torsion to fracture. Other tests were applied with the order of torque and tension loading reversed. The nominal stress-strain curves for these two tests approximately coincide indicating that the assumption of isotropic yielding is valid. In addition, these tests verified the requirement by the slip theory of plasticity that prestraining below 140 pct of the proportioned limit stress in either torsion or tension did not influence the subsequent plastic stress-strain relations in tension or torsion. Another type of test was conducted to check the assumption that the axes of principal stress and strain coincide during plastic flow and variable stress conditions. These tests were conducted by applying combinations of axial tension, internal pressure, and torsional loads such that the axes of maximum principal stress could be rotated through 90" during the loading path. The results of those tests showed that the angle between the axes of principal stress and strain varied greatly and that the assumption of coincidence between axes of principal stress and strain is not valid. Introduction In various metal processes including forming of sheets, rolling of bars, and extrusion of rods, metals are subjected to stresses beyond the yield strength of the material. Often these stresses are not simple stresses acting in one direction, but are combined stresses acting in more than one direction. Structural and machine members are often subjected to combined stresses. To adequately determine the factors of safety for these members, it is necessary to know the plastic stress-strain relations of the material used for various combined stress conditions. Various theories have been proposed for predicting the plastic stress-strain relations for combined stress in terms of the simple tension plastic stress-strain relation for the material. To determine which theory might be adequate, test results must be obtained for various combined stress conditions, in order to compare the actual with the assumed theoretical behavior. Although there is considerable test data available for combined stress conditions in which the principal stress ratios are constant, relatively little test information is available for vari-

Jan 1, 1954

By H. H. Reamer, B. H. Sage

The formation volume and the relative volume of the liquid Phase of mixtures of Condensate and gas from five different parts of a field in the Louisiana area have been established experimentally. These studies included gas-condensate ratios as high as 25.000 cu ft/bbl at pressures up to 5,000 psi. The gravities of the tank condensates were between 53.9° and 63.9° API. The compositions of the condensate and gas samples inves-ligated are presented in tabular form. The formation volume. the relative volume of the liquid phase. and the specific volume of the mixtures are available. A rough correlation of the formation volume as a function of pressure. temperature, and gas-condensate ratio has been presented. This correlation i-considered applicable only to the range of conditions covered in this investigation for systems of similar nature and com-position. INTRODUCTION Often a knowledge of the influence of temperature. Pres sure, and relative quantities of condensate and gas upon the volumetric behavior of fluid*. from a given field has been employed in estimating the Conditions existing in the reservoir. The early work of Beecher and Parkhurst' and the more rrcent Studies of the Dominguez' and San Joaqnin Valley Field;: are examples of experimental studies of this character. Correlation of the volumetric behavior of naturally occurring hydrocarbon mixtures has Proved To be feasible' . at low gas-conden-sate ratios-; for fluids*. from a single geographic area. Progres 5 is being made in the Prediction of the volumetric behavior of distillate systems at high gas-condensate ratios and pressure.. However. the estimation of the retrograde". ' dew-point pressure still remains uncertain and probably can best be established by experiment. For this reason it appears of interest to make available experimental information about the volumetric behavior of mixtures of condensate and gas from five different part.; of a single field. This material shows a rough similarity to data for mixtures of condensate and gas from San Joaqnin ' Valley Fields. In the present paper. 110 attempt has been made to coordinate the available information on tbe volumetric behavior of fluids from condensate fields. It appears hopeful that progress can be realized by the utilization of recently developed equa-tions of state.!' However. the primary problem in any such correlation is the proper identification of the components and constituents of naturally occuring systems. Additional experimental information may be required to permit the determination of the values of the constants of the equation of state for References given at end of paper. Manuscriptt received in the office of the Petroleum Branch June 11. 1951. *For present purposes low gas- condensate ratios will he considered as those below 3,000 cu ft/bbl, and the region of high gas-condensate ratio will be limited to compositions containing more than 5,000 cu ft of pas per bbl of condensate. Mixtures Containing between 3,000 and 5.000 CII ft OF gas per bbl will be considered of intermediate gas-condensate ratio.

Jan 1, 1952

By Richard L. Rains

The Bureau of Mines conducted a mineral investigation of the 29,000-acre Dixie Summit area near Elk City, Idaho, during the summer of 1989. At the Petsite mine a marginally economic, identified resource of 4.9 million tons with an average grade of 0.023 ounces gold per ton was delineated. Possible resources of gold, along with silver, copper, lead, and zinc, occur in at least eight other lode deposits. Placer gold may be recoverable by recreational-sized suction dredges in some stream drainages, Five lode mines in the study area have produced over 5,516 ounces of gold (placer gold production was not recorded), 4,757 troy ounces of sliver, 36,746 pounds of lead, and 3,800 pounds of copper. Current mining claims in or adjacent to the study area total 460 lode and 70 placer claims. There are two patented lode claims within the Dixie Summit study area.

Jan 1, 1991

By B. Yawney

A copper-nickel sulfide concentrate was leached in water at about 2000C under oxygen pressures of about 0.35 MPa. Oxidation of sulfide to sulfate was virtually complete in about 30 minutes, resulting in greater than 95% copper and 98% nickel extractions. Leaching temperature was shown to be the most important factor affecting metal extractions. Measured rates of oxygen consumption were used to develop batch kinetic data. Mini-plant continuous pressure leaching tests agreed with batch leach results. A proposed overall flowsheet is briefly examined.

Jan 1, 1976

By M. R. Yalamanchili, J. D. Miller

Discussion by M.R. Yalamanchili and J.D. Miller The authors, M. S. Celik et al., should be recognized for their efforts to describe the flotation behavior of boron minerals. In the case of borax and other soluble salt minerals, analysis of the flotation chemistry has been difficult because of the high ionic strengths associated with these soluble salt systems. However, considerable progress has been made in this area, and recently a surface charge/collector colloid adsorption model was proposed by Miller and his coworkers to explain the collector adsorption phenomena observed in soluble salt flotation systems (Milleret al, 1992; Yalamanchili et al., 1993; Miller and Yalamanchili, 1994; Yalamanchili and Miller, 1994a: Yalamanchili and Miller, 1994b). In this work, the sign of the surface charge of alkali halides in their saturated brines was established on the basis of nonequilibrium electrophoretic mobility measurements by laser-Doppler electrophoresis (Miller et al., 1992). Generally, these results are what would be expected from the simplified lattice-ionhydration theory. This electrokinetic information coupled with the stability and prevalence of collector colloids in such soluble salt flotation systems indicates that the selective flotation of alkali halides is due to the adsorption of oppositely charged collector colloids by heterocoagulation. Experimental flotation/bubble attachment results for 21 different alkali halides (Yalamanchili et al., 1993; Yalamanchili and Miller, I994b) confirmed that the flotation response of soluble salt minerals with weak electrolyte collectors can best be explained by the adsorption of oppositely charged collector colloids rather than by the adsorption collector ions and/or neutral molecular dipoles as originally suggested by many researchers (Fuerstenau and Fuerstenau, 1957; Schubert, 1967; Roman et al., 1968). In addition, the flotation of certain alkali oxyanions (Pizarro et al., 1993) and double salts such as schoenite and kainite can be explained by the same collector colloid adsorption mechanism (Miller and Yalamanchili, 1994). The borax flotation results reported by Celik et al. need to be examined in terms of the above mentioned surface charge/ collector colloid adsorption model. Unfortunately, the authors seem to be unaware of this recent work that nicely describes soluble salt flotation with weak electrolyte type collectors such as amines and carboxylates. In view of our past work, the flotation characteristics of borax were of particular interest, and, in this regard, the results of dodecyl amine flotation of borax reported by Celik et al. have been examined in further detail in the light of experimental results from our laboratory. In our research, a vacuum flotation technique was used to study the flotation response of borax (Na2B407.10H20), which has a solubility of 39 g/L at 25 °C) with dodecyl amine hydrochloride as collector. These chemicals were purchased from Eastman Kodak and used as received. Saturated solutions of borax at desired pH values were prepared by continuously stirring the salt solutions over a period of about 10 hrs. It should be mentioned that the conditioning time to achieve equilibrium is an important variable and can significantly change the flotation response of some soluble salts (Yalamanchili et al., 1993). Collector was added to the saturated borax solutions containing about one gram of 100x 150 mesh borax particles, and conditioning was done for about 20 minutes prior to flotation. The borax flotation recoveries from saturated brine are presented in Fig. 1 as a function of collector addition at the natural pH of 9.3, as reported both by Celik et al. and as measured in our laboratory. In addition, the region of precipitation for the dodecyl amine hydroborate is included in Fig. 1. It can be seen in Fig. 1 that the flotation response curves are separated by about one order of magnitude in R12NH3CI collector addition. The flotation results of Celik et al. show that the maximum borax recoveries can be obtained below the solubility limit of the dodecyl amine hydroborate collector. However, in our experiments borax flotation seems to occur only after the precipitation of the dodecyl amine hydroborate collector as might be expected from the collector colloid adsorption model (Yalamanchili et al., 1993) if borax were negatively charged. Further analysis by nonequilibrium and equilibrium electrophoretic mobility measurements for borax indicates that borax is negatively charged at the natural pH of 9.3, as discussed below. The reliability of the nonequilibrium electrophoretic measurements has been demonstrated previously for alkali halides and alkali oxyanions (Miller et al., 1992; Miller and Yalamanchili, 1994). The equilibrium and nonequlibrium electrophoretic measurements for borax were found to be consistent and are presented in Table 1. These results provide clear evidence that borax carries a negative surface charge in its saturated brine (pH 9.3), and the sign of the surface charge of borax reverses and becomes positive if the pH is reduced to 8.6. The equilibrium between borax and its saturated brine can be described by the following reaction: [2Na2B407.1OH2O-4Na++B407=+HB4O7 +OH+19H20] It appears that the oxyanions of the borax lattice provide

Jan 1, 1995

By R. W. Shoenberger, J. D. Clendenin, W. L. McMorris, N. Schapiro, B. R. Kuchta, A. A. Terchick, R. J. Gray, J. G. Price

INTRODUCTION * The United States is fortunate in having enormous reserves of metallurgical-grade coals. Although these coals are better in quality and more accessible than most coals found throughout the rest of the world, the best grades of these coals are being depleted. Consequently, more efficient exploration tools and techniques, such as advanced methods of core drilling and logging, correlation by palynology,** stratigraphy, paleontology and petrography are being used to help assess the extent and quality of the remaining coal reserves. Exploration and assessment of new and existing coal properties become of utmost importance in determining (1) the economic justification for mining the coal, (2) the optimum design of the preparation plant and (3) the most effective use of the coal. Fortunately, the cost of mining coal has remained stable because of better mine planning, more efficient operations and increased mechanization of mining operations. However, increased mechanization raises the amount of impurities in the coal mined, and this requires more and better coal beneficiation to meet the more stringent quality requirements set by the market. Besides, mechanical miners also produce relatively fine coal and, to ensure maximum liberation of impurities, much of the coal presently being used must be crushed to a finer size prior to preparation. The bulk of all coals presently used in this country is mechanically cleaned, much of it at a lower specific gravity than in the past. This necessitates the use of new and improved processes and equipment for coal washing and recovery, such as heavy-medium cyclones and vessels, and froth flotation cells. However, because wet-cleaning processes are pre- dominant in the United States and fine coal retains large amounts of moisture, the increased production of cleaned fine coal accentuates the need for new or improved methods and equipment for dewatering and drying this coal. The larger amounts of coal being beneficiated and the use of new and improved beneficiation processes will aid in controlling and ultimately eliminating sources of pollution. Modem coal markets demand coals that meet rigid specifications. Most coals are purchased under contracts that specify moisture, ash, and sulfur contents, or heating value, depending upon the end use. There has also been a growing trend toward specifying other properties, including particle size and coking capability. These specifications may include not only the * Editor's note: Because of the numerous and varied contributions of the associate authors of this chapter, the text does not differentiate between sections prepared by each individual as has been done in other chapters. ** Palynology is the study of plant microfossils, especially spores, pollen, and other types of fossils not usually studied by paleontologists.

Jan 1, 1968

By R. C. J. Goode, W. S. Rapson, W. R. Lawrie, L. W. P. Van Der Bosch

W. R. Lawrie (Member): As all the Institute members present are aware, the Ninth Commonwealth Mining and Metallurgical Congress was held in Great Britain from 3rd to 24th May, 1969. The Congress opened in London and the first week was devoted to technical sessions. Several receptions and other forms of entertainment were held in the evenings. The Congress was attended by some 1 200 delegates, many of whom were accompanied by their wives. As can be imagined a large organisation was needed to cater for all the whims of these delegates, to arrange accommodation and to provide transport for the technical trips, for the receptions and for the sight-seeing tours. Papers presented at the technical sessions proved of great interest. It was stimulating to hear of the developments taking place in the various branches of mining and metallurgy. The discussions which developed between men from so many different countries were thought provoking, led to new friendships and most of us made valuable contacts for the future. There were 141 papers presented in the one week. They were given in four separate halls with two, three and sometimes four papers coming up for discussion in each of the three sessions per day in each hall. Among the more interesting subjects were those concerning off-shore drilling and the facilities for production of petroleum and natural gas. Beach mining at Consolidated Diamond Mines drew a large audience. Automation, mechanization and other technical developments were well described and we were brought up to date with modern techniques of mineral prospecting. There was general discussion on the future of the mineral industries together with comments on the consumption and price trends of these metals and minerals. The future of uranium, of vital interest to us in South Africa, came in for much debate. During the first week, besides attending the technical sessions and seeing some of the sights of London, we were royally entertained. There was a banquet, attended by some I 400 people, where we were welcomed by Princess Alexandra, a reception by H.M. Government in the Banqueting House, and we were entertained at the House of Lords on a terrace overlooking the bustling and rather muddy river Thames. Then there was the visit to the Glyndebourne Opera. It is only in London that at 3 o'clock of an afternoon, nearly 1 000 people all togged up in dress suits and long dresses and carrying packets of sandwiches for supper could arrive at a station to catch a train, and not even cause a stir of interest or a raised eyebrow! This is the way we travelled 60 miles to the opera from London. Surely there can be no more picturesque or romantic a setting for an opera than this large 400-year old red brick manor house nestling in the green valleys of the unspoilt Sussex countryside. It was a glorious evening and though we returned somewhat late and tired, not one of us would have missed this experience. After the first week in London there was a choice of tours of one week to London and the Home Counties, Cornwall, a Geological tour to Scotland, South Wales, and North England. These were followed by further one week tours to Yorkshire and Lancashire, Scotland, West Country and Midlands, a Geological tour of Wales, and a Mining and Geological tour to Jurassic Iron Mines. We then returned to London for the final session and closing banquet. Post-congress tours were arranged to Europe and to Ireland. It was a wonderful Congress, a great experience, we made many friends and may there be many more congresses! . L. W. P. van den Bosch (Member): Much has already been said in appreciation of the excellent organisation and arrangements made for the delegates who attended this Congress. This report is confined to a brief discussion of the personal impressions gained from the papers presented and the technical visits attended. The papers covered a wide variety of subjects ranging from highly theoretical observations to practical descriptions of operations. There were three main themes, VIZ: 1. The attention given to research and its forceful application to practical operation. 2. A steady development in mechanization and automation leading to savings in manpower. 3. Improvization, modernization and adaptation of exisitng facilities. Thoughts on these themes can best be illustrated by comments on some of the industries visited. COAL The National Coal Board (N.C.B.) has been most progressive and all of us have heard of the Bevercotes Colliery with its completely automatic mining and coal handling equipment. This was not, unfortunately, on show but there is no doubt that this is one of the greatest advances in coal mining leading towards continuous production. Coal in Britain is fighting for its life against oil, North Sea gas, imported gases and nuclear power. Output is dropping, the less efficient collieries are closing down and efficiencies are steadily rising as the following tabulation indicates: In 1931: 1 million men produced 300 million tons of coal In 1947: 0.7 million men produced 230 million tons of coal In 1968: 0.4 million men produced 160 million tons of coal

By F. T. Cawood

The new mineral royalty regime for South Africa was signed into law in November 2008, with its main objective being to compensate the State for the depletion of public minerals through a royalty charge payable from 1 March 2010. The aims of this paper are to establish the potential impact of mining royalties on State revenues, industry affordability, and explore whether the dual formula system is likely to encourage miners to become refiners. It also measures the royalty dispensation against economists? tax standards in an attempt to make a judgement on the ?equity? of the new system. This paper argues that most stakeholders should be comfortable with most of the requirements of the Act for most of the time. However, the new regime is unlikely to motivate miners to become refiners, as the benefit of the reduced rate on refined minerals appears to be insufficient to justify the additional costs to refine the mineral resource to the prescribed states of beneficiation.

Jan 1, 2011

By Francis Cameron

Gloomy predictions that domestic mineral reserves are approaching exhaustion are unwarranted and may be harmful, this author contends. Specific mineral forecasting errors in the Paley Report are cited to support this contention, and steps that can be taken to insure a progressive mineral industry capable of keeping pace with the major raw material needs of the nation through advancing technology are suggested. Mining is both exciting and rewarding —although at times somewhat frustrating— and we all can have real pride in our industry, in its people, and in its accomplishments. It is, however, with concern that I have noted a deterioration in this Country in what might be called mining's stature and in the growth of a belief in many quarters that our mineral reserves are rapidly approaching exhaustion. In other words, there is a popular image that we are fast becoming a "have not" nation in many respects and that the domestic mining industry can no longer be considered, in the vernacular of Wall Street to offer much in the way of "growth potential." I do not subscribe to this hypothesis, nor do I be-li4ve that the record of the mining industry bears this out. However, let me add that we can, in time, talk ourselves into this frame of mind and we can hasten the day when this very well might come about by unnecessary and unwise legislation or regulation. My remarks today are basically designed to give my reasons for refuting this negative philosophy and to review our record. With your help, I know we can improve our image, and the public's recognition of our industry's peculiar problems. The progress of our civilization over the centuries has been fundamentally based upon proper use of raw materials, both agricultural and mineral, and upon energy, human or otherwise. As the standard of living has progressed century by century, the demands for mineral raw materials have increased in an irregular, but steadily rising progression. Fortunately, those minerals on which we depend most, i.e., iron, coal, petroleum, copper, aluminum, lead, and zinc have been neither too difficult to find nor to process into useful form. Iron, the most useful of all metals, is present in various amounts in most rock types and soils. Gold, seemingly the most generally desired (but certainly not the most useful of all metals), occurs in sea water in a far greater total tonnage than has been won from all of the world's known gold mines. If the latter is true, then why do we not see large installations treating sea water for the recovery of its gold content? The answer, of course, is that even the French, who seem, from their recent actions, to value gold above all else, have not devised a way of doing this at a profit. Theoretically, it is possible, but not with today's technology at a cost which would justify the effort. Man has exploited only those mineral concentrations which accidents of nature have placed within his so far limited means of finding and utilizing. What we geologists and engineers refer to as an orebody is nothing more than a concentration of minerals, exploitable with available knowledge, that will yield a value greater than the value attached to the energy and capital required to produce it. What is "ore" and what is not "ore" is, in the end, a matter of economics. The economic problem stems from the physical and chemical character of mineral deposits. The good Lord stacked the cards heavily in favor of rising costs by limiting the amount of the higher grade ores easily available. As the best and most accessible ores are depleted, it becomes necessary to work harder and with greater ingenuity to produce more from less accessible and lower grade resources. The quantity of mineral raw materials we can have in the future will be determined largely by what we can afford to pay for them in terms of human effort, capital outlay and production energies. We will always have the problem of cost with us and our only real means of keeping ahead of rising costs is by continually improving our technical abilities. We, in this country at least, no longer have open to us large and unexplored virgin wildernesses in which a pick-and-shovel prospector might uncover an untouched mineral bonanza. The rest of the world also has few conventional frontiers left in which the explorer-prospector is free to roam. We do, however, have enormous land areas unexplored, and untouched po-

Jan 1, 1969

By T. H. Alden

Using alternating tension-compression straining, the hardening of magnesium oxide single crystals was studied up to large stresses and strains. At 0.25 pct plastic strain amplitude, the hardening curve is approximately linear with slope 25,000 psi from the shear yield stress, 7 to 8000 psi, to 35,000psi. Above this stress, the slope decreases. The strain hardening behavior of MgO is considered qualitatively similar to that of metal single crystals. The relatively high stress attainable by strain hardening is associated apparently with the high yield stress on the cross-slip system, (001) <110>. Cleavage fracture during testing is uncommon. It is argued that the centers of high internal stress at glide band intersections, at which cracks tend to nucleate, are dispersed by cyclic strain. Special features of the glide band structure produced by cyclic strain and revealed by dislocation etch pits, support this view. Strain hardened MgO has mechanical properties greatly superior to the as-received material: yield stress, greater than 100,000 psi; elongation to fracture about 1 pct. A material is said to strain harden if the yield stress increases with an increment of plastic strain. This definition is usually applied for straining done in one direction, but is also applicable when the strain direction is periodically reversed, Fig. 1. For certain metal single crystals, data are available which permit a comparison of the hardening behavior for cyclic straining and for tension straining.&apos;-4 With certain qualifications, these data show that the same processes of hardening are operative in each type of test.5 Despite this fact, the importance of the technique is not immediately evident, although tension-compression studies of the common metals appear to suggest some deficiencies in theories of strain hardening developed exclusively on the basis of tensile tests. However, a recent observation suggests that the cyclic straining method may be very useful for studying semibrittle crystals in which large plastic strains are not accessible in unidirectional testing. The observation is that zinc crystals, when strained in tension-compression at -52°C, do not fail by cleavage at low stress (-500 psi)6 as they do in tension, but harden to a limiting stress of more than 5000 psi over a total plastic strain of about 600 pct.2 An important characteristic of the behavior of zinc crystals is the high stress, relative to the yield stress, attainable by strain hardening. By comparison, the hardening of aluminum single crystals tested by an identical technique saturates at 1100 psi. This difference is best explained by the cross-slip hypothesis of dynamic recovery.7,8 In zinc, cross slip is difficult because of the high yield stress for glide on planes other than the basal plane in the < 1120 > zone. The present work was undertaken in order to test whether these methods and ideas are applicable to other materials. Magnesium oxide single crystals, in common with most crystals of the rock-salt structure, deform plastically but fail by cleavage after a small strain when tested in tension. It was hoped that larger strains would be attained using tension-compression. There is, in addition, evidence 8a which shows that slip on the probable cross system, (001) < 110>, is difficult in magnesium oxide; it may therefore be possible to attain high stresses by strain hardening. 1) EXPERIMENTAL PROCEDURE Experimental methods used in this study were based in part on techniques reported in papers of Stokes, Johnston, and Li.&apos; MgO blocks, purchased from Norton Co., were used without further annealing. Specimens were cleaved to dimensions approximately 0.125 in. sq and 1 in. in length. The gage section, formed by chemical polishing, was sprinkled with 280 mesh silicon carbide particles in order to introduce fresh dislocations. The crystals were then cemented into cylindrical aluminum adapters and clamped in an Instron testing machine. One of two alternating straining programs was used. In the first, total cross-head travel was established and increased in steps after various numbers of cycles. In the second, a capacitance gage was used to directly measure the elongation of the specimen and the crosshead was controlled so as to keep the plastic strain amplitude constant. The straining was always symmetrical with respect to the initial, zero strain condition. While both procedures produce strain hardening, only the latter permits a measure of the total plastic strain so that hardening curves may be drawn. Constant plastic strain amplitude tests were done

Jan 1, 1963

By Clarence Merritt

STAINLESS iron, as mild stainless steel is usually called, an alloy ranging from 11.50 to 15.00 per cent chromium with carbon under 0.12 per cent, has been considered to be not appreciably affected in respect to corrosion resistance by heat treatment. This metal, while one of the most widely used of the "straight" chromium stainless alloys, has failed in many applications because of insufficient information regarding heat treatment. These failures have been attributed to many possible causes from an inherent lack of resistance to corrosion and misapplication to mysterious electrolytic effects or comparatively minute non-metallic inclusions. Many uses for a steel with such excellent physical properties is are latent in this alloy have been lost on account of corrosion failures which could have been avoided by applying proper heat treatment. The alloy has not received the recognition or attention it should because of the fact that&apos; the details of its metallurgical behavior were not thoroughly understood. Response to heat treatment of the steel is well known as regards tensile properties, 1,2 but its application has been for improvement in tensile characteristics or on account of machining considerations rather than for corrosion prevention. The potential user of this steel has not been clearly advised in papers, either technical or commercial, that have been written about it in the last 10 years or more, of particular features that are of prime importance in developing the excellent properties of this metal. The data to be presented in this paper are concerned mainly with the effect of heat treatment on the corrosion resistance, but a study has also been made of the concurrent microstructural changes and an explanation developed for the phenomena revealed, as well as a correlation to the other physical properties-hardness, tensile characteristics and impact strength. Stainless steel, largely used for cutlery purposes, an alloy of approximately 13.00 per cent Cr with 0.30 per cent C, must be hardened and the surface prepared by polishing or pickling for best resistance to staining and corrosion.3 Monypenny reports that a loss of hardness is

Jan 1, 1932