Search Documents

By H. H. Spain, R. C. Rumble, H. E. Stamm

This paper presents a reservoir analyzer study of the performance of the Woodbine formation in the East Texas basin. The study was made possible by the compilation of available information on the configuration. thickness and the pressure drawdown of the formation. The investigation was made of the pressure variations in the basin incident to production from the several Woodbine reservoirs. In addition, the apparent compressibility of Woodbine water was evaluated so that the potential water yield of the formation could be determined. The distribution of permeability of the Woodbine sand and the interference between producing areas were also investigated. In conjunction with this basic study of the Woodbine sand, an acceptable match of the production-pressure relationship in the East Texas Field was established on the analyzer. INTRODUCTION When production is taken from a reservoir contiguous to an aquifer, the resultant pressure gradient causes a water influx into the reservoir. For some years it has been the practice to predict the performance of water drive reservoirs with mathematical equations that relate the water influx into reservoirs to their pressure behavior. A rigorous solution of these equations is quite complex: hence, the conventional method requires the simplifying assumptions that the formation have constant thickness, permeability and poiosity, and that it have a known and regular shape. It is necessary to use performance records of the reservoir in question to determine the equation constants that make the results of the mathematical calculations duplicate the reservoir history. The values of the constants determined in this manner sometimes differ so greatly from theoretical or measured values that the constants appear unreasonable. The equation constants comprise such factors as the thickness, porosity and permeability of the formation, and the viscosity and compressibility of water. Usually the thickness, porosity and viscosity are known within a reasonable degree of certainty. whereas the formation permeability and the water compressibility are known with considerably less certainty. Hence. permeability and compressibility values are arbitrarily selected that will make the mathematical equations duplicate the reservoir behavior. In many reservoir studies the value of the compressibility of water thus selected has exceeded the reported value by a factor of from severalfold to manyfold. Whether this excessive value results from the inadequacy of the mathematical approach to take into account the shape irregularities and the heterogeneities of the aquifer, or is due to some type of formation compaction and decrease of porosity has not been established. Because of the significance of the potential water yield of formations with reference not only to oil reservoirs but to water resources as well, it is very important that a representative value for the effective water compressibility be determined. One of the best known examples of a field for which it has been possible in the past to predict the future reservoir pressure is the East Texas Field. Until about 1943 it was possible by means of mathematical equations to duplicate past pressure behavior and to predict with a high degree of accuracy the reservoir pressure of the field. Since 1943, however, the calculated pressures have deviated progressively from the observed pressures to such a degree that in recent years, it has

Jan 1, 1951

By L. Capponi

At Tapira Mine (Tapira/MG/ Brazil), the largest phosphate concentrate producer in Brazil, the mining is fully mechanized and carried out using open pit mining. This work presents a review of the sampling protocol used for short term mine planning at different stages. Sampling is carried out in two steps. Firstly, diamond drill cores are sampled at 50 x50 x5 metre pattern. Fosfertil analyses grades of P2O5, Fe2O3, CaO, MgO, SiO2 and TiO2 plus geological logging. This information feeds the long term block model. Secondly, drill cuttings are collected at the mining faces released for blasting. The drilling pattern is staggered and when blasting is not necessary, a drill hole is made centered in the block area (25 x 25 x 5 m). The primary samples have mass approximately 60 kg and the same chemical parameters are analysed. Metallurgical and mass recovery tests are performed as well. These samples are used to build the short term block model. At the final stage, the short term mine planning model is used to build a stockpile blending model which is simulated using a spreadsheet to match the goals established by the process plant.

Jan 1, 2009

By Arnold Hoffman

A RESPONSIBLE steel executive recently declared that scrap shortages, despite fantastic prices reaching up to $50 per ton, are responsible for the loss of 140,000 tons of steel a month and that in March 1947 alone 25 more steel furnaces could have been operating were it not for scrap scarcities. His answer to this serious situation was to ask for a speedier flow of scrap and also abolition of Government control over pig iron distribution. It would be more logical, perhaps, if an answer to this growing problem of scrap deficiency were sought within the steel industry itself. As long ago as 1933, L. B. Lindemuth, a consulting steel metallurgist, warned the steel industry that a shortage of scrap was inevitable and that beyond 1938, adequate supplies for open-hearth furnaces could not be expected. The outbreak of war, with consequent phenomenal demands on the industry, accelerated production of steel and further worsened the scrap situation. Today we are suffering from a condition which could have been prevented had the industry been more far-seeing and provided for an inevitable contingency. However, better late than never, and measures can now be taken to alleviate permanently scrap shortages in the future. This can be done by greater utilization of heavy sinter which experience proved is an excellent substitute for scrao and lump ore.

Jan 1, 1947

By Margaret N. Maxey

Man's capacity far fretting is endless, and no matter what difficulties we surmount, how many ideals we realize, there is a stealthy pleasure in rejecting mankind or the universe as unworthy of our approval. - Will Durant Until recently, reasons for favoring one or another energy alternative were advanced on the basis of technical considerations and economic realities. However, it is an indication of the cultural climate of our society and growing realization of why energy is our master resource that many citizens have begun to express concern about the social and ethical implications of our energy deci¬sion-making. A vivid indication of this shift toward ethical concerns is reflected in the attention being focused on conservation - even to the point of regarding it as a virtual panacea equivalent to a "free energy resource." Among others, the authors of a publication by Resources for the Future cautions us about the difficulties of defining conservation. They also point out that unrealistic expectations for achieving the high levels of conservation claimed by true believers may boomerang if, at the same time, we are morally required to maintain economic growth and robust productivity for the basic well-being of more people. In its economic meaning, conservation signifies the most economic or cost-effective applications of energy, together with other resources, in a given process or activity. To achieve conservation that is cost-effective, saving energy alone is not sufficient; the cost involved in saving the energy must be no greater than the cost of the energy that is saved. Using its thermodynamic meaning, conservation and efficiency are viewed as constrained by physical laws and measured against ideal limits set by these laws and processes. Since achieving higher levels of technical performance is not without costs, the economic meaning of conservation must be factored into technical possibilities. It is the ethical, equity and environmental meaning of conservation that concerns us here. In its third meaning, conservation consists in moderation as a value which appears inherently worthwhile both in itself and in relation to social choices dedicated to achieving distributive justice. The value of moderation seems predicated on the assumption that natural resources and the environment have fixed, finite, exhaustible capacities for satisfying human needs. Hence norms for moderating human behavior appear to require prescriptions by some authority. Such norms presuppose some agreement on "essential" uses of energy. However, the difficulties of setting behavioral norms loom large, because "... it is as difficult to determine essential energy consumption as to determine what is essential in any other phase of consumption, whether it involves food, clothing, shelter, or recreation." The ethical meaning of conversation is further complicated by a centuries-old argument over the proper exercise of stewardship - i.e., how best to develop natural resources. On the one hand, the preservationist position insists on an inviolate, "hands-off" policy and stands opposed to ongoing development of wilderness areas and mineral resources. On the other hand, the "scientific conservationist" who preaches the "gospel of efficiency" insists on development of resources based on principles of sustained-yield, multiple use and - in the case of competing claims - reserving resources or land for their "higher use." Current confusion reigns among opinion leaders in the environmental movement because they appear to have lost the genius of the original Conservation ethic, developed in the 19th century. They seem to think that conservation is preservation. The question I wish to explore is whether a single-minded, exclusive pursuit of "conservation" in its economic, thermodynamic and preservationist meanings may actually do more harm than good in serving the ethical goals of conservation. There

Jan 1, 1986

By R. Venkataramani

Even though the mining industry in 1966 produced more ore than ever before, current extraction rates are only a fraction of what is expected in the later years of the twentieth century. Nearly 90% of all metals and-mineral products consumed last year was recovered by open-pit mining. This has placed great pressure on this segment of the industry which has, consequently, resulted in some spectacular developments. With increasing size of projects, the need for increased sophistication of engineering, planning, management and administration of modern mining installations has never become more apparent. The design of complete systems for the mine and plant that fit the mould of today's business and social environments is undergoing an evolutionary process. Traditional concepts in mine development and operations are being sidestepped in favor of new ideas and principles. As the overburden thickness increases, materials handling presents a major problem to mining companies, especially those concerned with the mass production of ore and waste from low-grade deposits. The profit margin here is likely to be significantly less as to take chances with capital investment. 1 Constant efforts are needed to improve upon productivity if the ore is to be economically mined.

Jan 1, 1970

By P. Moyo, S. Dixon, R. Norcross

The separation and recovery of copper from cyanide solution has been investigated since the early 1900s. The precipitation of copper using sulfide ion was patented in 1911 by Williamson, published by Leaver & Woolf of the USBM in 1931 and Cyanamid in 1960s. The current practice of sulfide precipitation is used in various processes such as “SART" for cyanide regeneration and copper recovery. The precipitation of copper sulfide requires the pH of the clear solution to be in the range of 4-6. The precipitated copper sulfide can be sold to smelters. Alternatively, copper cyanide can be precipitated from clear solutions in the pH range of 2-3. However, selling copper cyanide is challenging because of its cyanide content. Past work has focused on the use of boiling sulfuric acid to convert copper cyanide to copper sulfate as published by Seracini in 1991. This paper describes a simple process to convert copper cyanide to copper oxide using sodium hydroxide at ambient temperatures. The cuprite can be sold to smelters or used as a feed to an electrowinning circuit to produce copper cathodes. The process provides an effective method to recover copper from cyanide solutions with a lower capital requirement.

Mar 2, 2022

By M. Birdsell

"Sustainable long-term restoration requires adequate planning and preparation, implementation, and measurement goals to monitor success associated with restoring sites to pre-disturbance levels of ecological health. The Buckhorn Mountain Mine riparian habitat restoration project has been a multi-year endeavor with a variety of restoration techniques implemented by Kinross Gold/Crown Resources Corporation. INTRODUCTION The Buckhorn Mountain Mine procured mitigation lands during the permitting process to be set aside for long-term restoration. A portion of this mitigation land included three aquatic habitat mitigation parcels; a spring and wetland complex and two stream and riparian corridors. These properties were historically used for agriculture purposes and livestock grazing. During initial permitting, habitat monitoring and mitigation plans were created to help guide restoration, and provide measures for success. Various techniques and adaptations have been implemented on the properties since 2007, and continued efforts are being implemented annually to ensure the long-term success of the project. Field measurements are collected annually to ensure mitigation objectives are being met, and provide opportunity to modify restoration efforts when necessary. MATERIALS/METHODS Restoration efforts have included implementation of several methods including livestock exclusion, treatment of state and locally listed noxious weed species, installation of regionally sourced riparian plant species and local stock willow cuttings. Annual mechanical and herbicide treatments for noxious weeds have been conducted annually. Efforts to control reed canarygrass (Phalaris arundinacea) have been implemented since 2013; methods include mechanical and herbicide treatments. A combination of methods has been employed to help aid restoration of native species within the riparian corridor, and increase survival of planted species, including weed matting and browse barriers to aid riparian planting success. Instream planting of local stock willow have also been employed to increase stream vegetative cover and provide long-term bank stabilization. Most recently, a perched culvert near one of the properties has been replaced with an aquatic life passable culvert designed to aid in the upstream migration of fish species into the stream system. Efforts to provide increased fisheries into upstream portions of the system and aid in restoration of stream bed and bank have been employed to increase the ecological value downstream of the replacement. In addition to efforts completed by the client to provide restoration efforts, a local non-profit organization, in conjunction with the client, installed beaver dam analogues (BDAs) in the fall of 2014. These structures are intended to raise water levels along stretches of incised channel in an attempt to flood historic off-channel floodplain"

Jan 1, 2016

This paper is for mine managers. It is about maintenance of mining equipment. This is an extremely broad subject so this paper is given with the caveat that it necessarily contains generalisations, not true in all cases, but broadly correct. The job of mine managers is to be good at making money from the excavation and preliminary treatment of mineral. To do this well, they need to understand the cost and value drivers in the business. This includes understanding the drivers associated with maintenance. Maintenance is often identified as a problem at mine sites. It is frequently listed as the cause of production shortfalls when reporting. The state of maintenance within mining as an industry is generally among the lower end of the range, when compared to manufacturing, petrochemicals, etc. Why is this? Experience and review of many audits and evaluations of maintenance has shown that some patterns are consistent with good performance and some consistent with poor performance. These often centre around the time horizon of the management team and are associated with knowing the sensitivity of the business to certain maintenance drivers and the mechanisms of maintenance and their results. To summarise, some common misunderstandings can be listed as statements that are obvious and extrapolations from those, which are not necessarily correct. For example: High availability of equipment is necessary for production. Incorrect extrapolation:focus on availability will produce high production. Design is often the greatest factor in determining the reliability of a mining machine. Incorrect extrapolation: the newest and biggest machines generally have the lowest cost operations. Operation has an enormous impact on machine productivity and reliability. Incorrect extrapolation: the fastest operators are generally the best from a productive point of view. Some maintenance improves the performance and reliability of machines. Incorrect extrapolation: more maintenance will give you more reliability. Some maintenance depends on disassembly and reassembly of components. Incorrect extrapolation: assembly is basically the reverse process of disassembly. Maintenance improvement in the mining industry in the last 15 years has focused largely on planning and systems improvement. Incorrect extrapolation: most of the problems in maintenance can be traced to a lack of planning. Actions based on flawed extrapolations will steer a business suboptimally. It is therefore important that the mine manager understands these issues so that the improvement effort can be directed to the greatest benefit.

Jan 1, 2006

By Antonio Mendoza

El presente texto describe el sistema de manejo de agua y aire, las actividades integradoras, preventivas, de análisis y ejecución realizadas para describir la respuesta a los retos del futuro inmediato para alcanzar los objetivos ambientales en la mina Antamina.

Jan 1, 2012

By James R. McVey

A new method for measuring deformations of rock surfaces in underground excavations has been suggested by Dr. James Powell of Brookhaven National Laboratories (BNL) and subsequently developed and successfully demonstrated in a mining environment by the Federal Bureau of Mines, Spokane Mining Research Center (SMRC) and Brookhaven National Laboratories. The system uses 35-mm photography of targets strategically located on surfaces of interest, such as across the roof and on the sides of a mine drift or tunnel. The optimum tar-get, as determined in this investigation, consists of a white ?X? made with 1/8-inch-wide reflective tape on a black 6-inch square. Photographs, taken in pairs from two separated camera positions and at regular time intervals, were analyzed at the Bureau by hand and at Brookhaven National Laboratories using techniques and equipment similar to those used in cloud chamber film analysis. Test results show that deformation-measurement accuracies of better than ±0.020 inch in a drift that is 20 feet wide can be expected. This degree of accuracy, plus providing displacement data in the X, Y, and Z directions (rather than the one direction formerly possible), makes this a noteworthy and useful tool for industry as well as for mining research.

Jan 1, 1974

By R. F. Yap, N. Arbiter, C. C. Harris

A fully-instrumented driving mechanism has been constructed to study the power, aerating and solid suspension characteristics of several laboratory flotation machines. Machines operating over normal flotation speed ranges give substantially constant power numbers in liquid systems indicating that they operate close to fully baffled turbulent flow conditions. Owing to lack of geometrical scaling, power numbers for different sizes of cells of the same make are different. Even larger differences occur between cells of different manufacturers. For a given impeller, varying the tank size did not significantly affect the power consumption. Tank geometry and baffling has a slight effect on power consumption with shrouded impellers. For a given impeller speed, suspension height decreases while power increases with increasing mass of solids in suspension. While power consumption is hardly affected by particle size and clearance between the impeller and tank bottom, the suspension height significantly increases as clearance increases and as particle size decreases. Aeration was found to affect not only power but also the suspension characteristics of the machine. For closely sized particles, drastic sedimentation occurred when a critical value of the air flow number was exceeded. The critical air flow number decreased with increasing particle size. This effect was less marked with a wide particle size range. The self-aerating capacity of flotation machines increases with cell size at a given speed for the same impeller-shroud system, but decreases in the presence of frother and solids. Equations have been established for correlating all of the studied variables. Data taken from the literature were also correlated with these equations. The modern mechanical flotation machine has, over a period of 60 years, displaced other designs to become the dominant type. Once the correct chemical environmental conditions have been established, the major requirement, selective mineral-air adherence, is essentially a function of two operating variables — impeller speed and air rate. The special nature of this dependence is such that in the same apparatus, but under different operating conditions, adherence can be either prevented or destroyed. Another aspect of this observation is that flotation machines though differing in detail to a considerable extent can produce similar metallurgical results. It must be concluded that having determined the correct reagent levels, establishing the correct operating conditions are at least as important as machine design. Since about 1960, after 30 years of fairly stable circumstances, manufacturers have been developing new types of machines whose major feature is emphasis on pulp flow characteristics by virtue of new im-peller-stator designs. As far as can be ascertained, these new designs necessitate radical departures from accepted impeller speed-air rate values. Performance data are still awaited. Flotation machine development has been empirical, as is selection of operating conditions. The purpose of the work at Columbia University has been to elucidate the fundamentals of the subject so that the purely mechanical aspects of the flotation process can be understood in hydrodynamic terms.1-6 Hopefully, this might lead to intelligent selection of a particular machine and its operating conditions for a specific ore based on a minimum of testing, or even to new types of flotation machines. The present investigation is the most comprehensive to date.7,8 Earlier work, which was largely exploratory, has been repeated and extended and employes the most accurate measuring techniques available. Additionally, sufficient hydrodynamic data were obtained under flotation conditions to delineate the relevant operating ranges. Attention has been given to scaling in that several geometrically scaled tanks and impellers have been constructed and tested; it has been pointed out elsewhere that undistorted geometrical scaling rarely pertains in flotation machine design.5 This paper is divided into sections dealing with relevant combinations of the three phases: liquid, air and solid. Summaries of the literature have been given in previous publications2-4 and will not be repeated here. Recently, several reviews of mixing have appeared, which can be usefully referenced.9-11 It is of interest to note that flotation is not included

Jan 1, 1970

By Ngonidzashe Chimwani, David Glasser, Diane Hildebrandt

"Milling circuits play an important role in achieving the desired product; tonnage, size distribution and properties, since they are directly linked to the comminution energy consumption for the whole process. A grinding model with a mathematical simulation was developed for an open milling circuit with a scalped feed from a hydro-cyclone. The circuit was optimized by determining the optimal conditions in terms of energy consumption which would produce a floatable product having a desired size range (i.e. -75 +9 µm) for a platinum-bearing ore. The simulation results showed an operating region comprising the best combination of the ball filling and mill speed to achieve the highest production of a floatable size class, with the minimum energy consumption.INTRODUCTIONBall milling is usually conducted in closed circuits in order to achieve a desired product size without material overgrinding. The technological importance of optimising milling circuits cannot be overemphasised (Toneva and Peukert, 2007). Previous work has brought significant insights into the benefits of modelling milling circuits (Austin et al., 1984; King, 2012; Toneva and Peukert, 2007). However, the ability to model these circuits is dependent on the performance of the classifiers and the fidelity of the grinding mill model used compared to the actual circuit (Toneva and Peukert, 2007). Austin et al. (1984) identified five types of milling circuits as shown in Figure 1 namely; the grinding circuits employing mill in an open circuit, normal closed circuit, reverse closed circuit, open circuit with scalped feed, and, the combined closed circuit. Depending on the presence of the first classifier, the second, or both as well as their corresponding loops (streams), the combined circuit (e) can reduce to; an open (d), a normal closed (b), an open circuit with scalped feed (c) or a reverse closed circuit (a). In the case of an open circuit, the mill is operated without being directly influenced by a classifier. The normal closed circuit does not have the first classifier and therefore the make-up feed is the actual feed stream. Conversely, the reverse closed circuit keeps only the first classifier. The open circuited with scalped feed has only the first classifier but does not have the second one. The overflow stream from the classifier is mixed with the mill product to form the final product for the downstream process."

Jan 1, 2016

By L. H. McGuire, L. B. Berger

"During the period October 31 to November 4, 1944, tests were conducted by the Bureau of Mines in the Cascade Tunnel of the Great Northern Railway Cc. to determine the effects upon the tunnel atmosphere of the use of a Diesel freight locomotive through the tunnel. These tests were conducted at the request of the company to ascertain whether undesirable conditions might be caused by the discharge of Diesel engine exhaust gas in the tunnel, which was constructed for an electric haulage system and is not provided with equipment for mechanical ventilation. The use of Diesel locomotives on the division that includes the Cascade Tunnel was under consideration as a means of augmenting haulage facilities for the abnormal freight tonnage that must be handled during wartime.As the Bureau of Mines has received requests for information on the extent of contamination of the air of railroad tunnels by Diesel locomotives, this report was prepared to make available for general information the data obtained during the tests in the Cascade Tunnel. As the test locomotive is of a type used on other railroads, and as the bore and grade of the tunnel and the tonnages moved are comparable to such factors on other roads, the data should be sufficiently representative to be of general interest. The exceptional length of the Cascade Tunnel made it an excellent location for obtaining information on the composition of the tunnel air and on the movement of air induced in the tunnel by the passage of trains.The writers are indebted to C. O. Jenks, vice president of the Great Northern Railway Co., who arranged for the tests, and to the following personnel of the railroad who cooperated in the conduct of the tests: I. E. Clary, superintendent, Spokane Division, J. L. Robson, superintendent of motive power, oil and gas equipment, J. F. N. Gaynor, superintendent of electric operations, William Lowney, master mechanic, Spokane Division, and D. F. Marston and Verne Nelson, assistant superintendents of electric operations.The Cascade Tunnel is on the Spokane Division of the Great Northern Railway and pierces the Cascade Mountains some 49 miles west of Wenatchee, Wash. The west end of this division is electrified from Appleyard Station, 2 miles east of Wenatchee, to Skykomish, Wash., a distance of 73 miles. Until the described tests, only electric haulage had been employed through the tunnel since it was first opened to traffic in January 1929.The Cascade is the longest railroad tunnel in the United States - 7.79 miles. The tunnel is single-track, perfectly straight, concrete-lined, and is on an essentially uniform grade of 1.56 percent, ascending from west to east. The cross-sectional area of the tunnel is 314 square feet, the dimensions being shown in figure 1. Elevation of the east portal is 2,880 feet and of the west portal, 2,240 feet."

Jun 1, 1946

By Robert C. Freas

The summer joint meeting of the East Tennessee and Carolinas Sections of SME was held in Morristown, TN, on July 29 and 30, 1994. The Friday portion of the meeting began with a field trip to Asarco Inc.'s Young Mine and Mill, one of four mines operated by the company in the Mascot-Jefferson City district. The Young Mill processes ore from two other mines as well as its own, first by heavy media separation and then by standard flotation processes. Zinc concentrates are shipped by truck and barge to an electrolytic refinery in Clarksville, TN. The heavy media rejects and the dolomitic limestone tailings are sold through Asarco subsidiary American Limestone Co. Saturday's technical session, organized by Program Chairman Bob Fulweiler of the Tennessee Division of Geology, provided a review and status report of the zinc industry in Tennessee. This article summarizes papers presented, including one on recent developments in underground blasting.

Jan 1, 1994

(Under this heading will be published notes sent to the Secretary of the Institute of members or other persons introduced by members) Young mining engineer, and geologist, member, technical, graduate with four years' varied mining experience in the West and Southwest as miner, surveyor and engineer. Past 18 months, work in mine geology, mapping and examinations. Would prefer assisting consulting engineer or work with exploration company in foreign service. Unmarried. Age, 28. No. 331. Member; aged 35, married, with 10 years' experience in the Southwest, thoroughly competent to take full charge of mining and milling operations. Particularly fitted to handle either gold or tungsten producers. At liberty February 1. Will go anywhere. No. 340. A member wants a roving commission to examine old mines of the Mother Lode in. California, especially those which can be bought for their taxes. Some of these mines are reported to contain large quantities of low-grade ores which can now be treated at a profit. No. 341.

Jan 2, 1917

By Charles L. Kimbell

Bulk carriers, freighters, and tankers are the three classes of marine vessels engaged in transporting mineral commodities. However, vessels in each of these categories are not devoted wholly to mineral commodity transport. Bulk carriers move agricultural products as well as crude minerals and mineral fertilizers, as ore/bulk/oil carriers also do. Freighters, owing to their great variety, can be devoted wholly to hauling mineral products or wholly to moving nonmineral goods, as well as carrying mixed mineral and nonmineral cargoes. They include general cargo carriers, full containerships, partial containerships, roll-on/roll-off ships, and barge carriers. Tankers, although largely engaged in moving crude oil and refinery products, also transport liquid chemicals, molasses, wine, liquefied natural gas, and other fluids. Although physical characteristics of vessels, such as sue, draft, crew requirements, and type of propulsion system, as well as fuel costs, have an undeniable influence on shipping industry performance, problems of and changes in the quantity and quality and types of material moved also significantly affect the shipping sector of the world economy. Unfortunately, comprehensive data in this regard are not available.

Jan 1, 1992

A novel method of reconditioning vertical rock openings which are on the verge of collapse has been developed, ant1 a world patent applied for, by LKAB, the Swedish iron ore mining company. Without anyone descending into the dangerous opening, workers can place concrete reinforcement in the unstable section using sand-filled canvas tubes which LKAR development engineers are calling "stockings." First application of the new technique was in several inclined ore pockets which form part of the underground crushing and loading station at LKAB's Kiirunavaara mine in Swedish Lapland. LKAB experience demonstrated that with other methods it took about three months to repair a pocket, and neighboring pockets had to be closed while repairs were underway. With the new stocking method, the work was completed in three weeks with no disruption of nearby activities. Production losses amounted to 10% over the three-week period, as opposed to 30% with other methods. The simplified technique could save millions of dollars in underground maintenance, according to LKAB.

Jan 11, 1978

By Gordon T. Austin

The combined value of production of natural abrasives, which include tripoli, special silica stone, garnet, staurolite, and emery, decreased about 24% in 1992. The decrease in the value of tripoli production was the result of a decrease in total production. Emery decreased owing to a decrease in the volume of the material produced. Special silica stone experienced a significant increase in unit value and decrease in the quantity produced. Garnet showed a 6 % increase in quantity and a 36 % decrease in unit value. Staurolite decreased about 27 % in the quantity produced and value compared with those of 1991. The fused aluminum oxide industry showed a slight increase in the quantity produced and a 4 % increase in the value of production. The silicon carbide industry saw a 7 % increase in the quantity produced and a 10 % increase in the value of production. Combined, the industries increased 4 % in quantity and 6 % in value compared with those of 1991.

Jan 1, 1992

By Edward R. Torak

The Ohio Coal Testing and Development Research Facility (OCTAD) was commissioned in 1992 by the Ohio Coal Development Office and the Ohio Power Company to support evolving process technologies that will lead to increased environ- mentally sound use of coal. OCTAD is equipped with advanced physical concentration devices and processes capable of beneficiating coal to levels beyond conventional practice. The first task of OCTAD operators was to test the cleanability of the Meigs Creek Seam Coal in advanced circuitry and compare the results to conventional cleaning levels. In testing the seams, OCTAD circuitry was configured to produce middlings on the coarse and intermediate size fractions. These middlings were subsequently crushed to a finer size (28M x 0) and subjected to cleaning in fine heavy-media cyclones and advanced froth flotation circuitry. Nearly thirty-six full-scale production runs at various operating conditions were completed during the campaign. The results of the test program are examined in this paper.

Jan 1, 1995

By N. Kyriazi, W. Duerr, J. Shubilla, J. G. Kovac, J. Kravitz

A joint effort by the Bureau of Mines and the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, was undertaken to determine how well self-contained self-rescuers, deployed in accordance with Federal Regulations (30 CFK 75.1714), held up in the underground environment. This report presents findings regarding laboratory-tested breathing apparatus from the first year of a 5-yr program as well as other related findings. The SCSR's were tested on human subjects and on a breathing and metabolic simulator. These results indicate that the apparatus, if well-treated, perform as expected except for manufacturing defects or quality control problems, which are identified. However, when the apparatus are carried in and out of the mine every day and stored at the working section, they may suffer abuse that can be extreme. Physical signs of abuse, unless extremely obvious, frequently are not detected by the miners or the mine operators; this poses a danger to a potential user in case of emergency. Recommendations include improved training in inspection procedures.

Jan 1, 1986