Search Documents

By Carl-Oscar Nilsson, Åke B. Nilsson

"The embankment dam at Storfinnforsen is 23 m high and was completed in 1954. The dam has an impervious zone with timber sheet piles and a support fill of glacial till. The pore water pressure in the downstream shoulder has during recent years increased due to deterioration in the sealing function of the timber sheet piling. There is a concern that the high pore water pressure in the glacial till will cause internal erosion initiating at a thin coarse transition layer between the glacial till and the rock fill along the downstream toe. As a remedial action in order to improvement of the leakage resistance a supporting berm of coarse rockfill against the downstream slope of the dam was constructed in year 2013. In addition a new impervious seal in the centre of the dam e.g. a diaphragm wall was considered. However, after further studies and a trial stretch of 40 drains each 20 m long and diameter 0.3 m an alternative with vertical drilled drains in the downstream support was selected. A contract has now started up to drill in a similar way to treat the full length of the dam with drains. The work is in the planning to be completed in 2016.Dam ConstructionStorfinnforsen Embankment Dam was put into operation in 1954. The dam is 330 m long and maximum height is approximately 23 m. The dam is constructed with a central core zone and supporting zones of earth and rockfill on the upstream and downstream sides giving an almost symmetrical cross-section about the dam axis, see Fig. 1. The upstream slope is 2H:1V down to el. 270 and 2.5H:1V below. On the downstream side the slope is 1.75H:1V down to +269 and 2H:1V below. The core zone consists of a timber sheet pile wall with a Zone 5 of glacial till, approximately 2 m wide, adjacent to the wall on the upstream side."

Jan 1, 2016

By C. Sun

Due to unfavorable geological condition, excessive deformation of mine drifts occurred in a large underground copper and nickel mine. In searching for a solution, a comprehensive underground monitoring program was implemented and the opening convergence and the surrounding rock deformation were monitored. A large number of field data were collected and thoroughly analyzed. The convergence and deformation as function of time and depth were determined and a rock stability index was proposed. Based on the deformation-time and deformation-depth relations, critical deformation times and locations were identified and defined as characteristic values to be used for mine opening and support designs. The characteristic values are critical in the application of two-step supporting system, and the determination of support parameters. The application of the method developed in this study has demonstrated that this practical approach in support design and installation is effective. With the two-step supporting system, a long-term drift stability can be achieved in the mine.

Jan 1, 1998

By W. Jilowa, C. Nguni, M. Simukoko, C. Nampungwe

The upsurge in cobalt price and demand is propelled by high demand from the electronics and electric vehicle industry. Konkola Copper Mines has cobalt occurring with copper in the ratio 1:10 in ore. The ore is treated in the concentrator and recovered at the smelter as an alloy (Cu 70%, Co 4%–7%, 15% Fe). Subsequent processing of the cobalt alloy is challenging, with very few plants able to treat it, leading to marketing challenges. Konkola Copper Mines sought to improve the cobalt alloy by producing a slag that is easier to handle and process in subsequent processes. Cobalt alloy (3.60% Co, 85.4% Cu) was re-melted in a copper bath four times the mass of the alloy. Silica and lime were added for phase separation and fire refining commenced. Following completion of fire refining and after holding the temperature at 1200°C, cobalt-rich slag was skimmed and blister copper was cast into anodes for electrorefining

Jan 1, 2023

By Henry M. Howe, W. P. Barba

When this country went into the war, but two concerns, The Bethlehem Steel Co. and The Midvale Steel and Ordnance Co., knew how to make steel fit for great cannons and at these concerns there were relatively few men who knew the whole art. Fortunately, certain of these men put their knowledge at the service of the Government, and proceeded to instruct the metallurgists at the arsenals and at various steel works. Doctor Howe, then chairman of the Engineering Division of the National Research Council, suggested that this work might be facilitated, and the number of effective gun-steel makers thereby increased, if a detailed description of the best practice could be written, giving the reasons for the various steps, and issued with the endorsement of a committee composed of those who were evidently the most competent authorities. It was thought that something would be gained by clarification of the subject, and something by the eminent authority of the members of the committee. To that end, the Engineering Division appointed a committee, consisting of the gentlemen whose names follow, to mention on1y those who retained their connection with it. At this time there were serious difficulties in the manufacture, for the Government. of aircraft and high-speed engine crankshafts, of certain ordnance forgings, and of shells for both the Army and Navy. This Committee was asked to study and report upon these, with a view to betterment of practice. There were indications that the source of some of the difficulties went back to the melting of the steel and the production of the ingot. Hence, the committee first studied steel melting and ingot production, in order to guide the wartime manufacturers to an even larger percentage of useful production from the steel initially melted. Committee on Steel Ingots W. P. Barba, chairman, Ordnance Dept., U. S. A. (formerly Vice Pres. & Gen. Mgr., Midvale Steel Co., Philadelphia). George K. Burgess, Chief of Division of Metallurgy, U. S. Bureau of Standards, Washington, D. C. Henry M. Howe, Then Chairman Engineering Division, National Research Council.

Jan 1, 1922

By W. P. Barba, Henry M. Howe

When this country went into the war, but two concerns, The Bethlehem Steel Co. and The Midvale Steel and Ordnance Co., knew how to make steel fit for great cannons and at these concerns there were relatively few men who knew the whole art. Fortunately, certain of these men put their knowledge at the service of the Government, and proceeded to instruct the metallurgists at the arsenals and at various steel works. Doctor Howe, then chairman of the Engineering Division of the National Research Council, suggested that this work might be facilitated, and the number of effective gun-steel makers thereby increased, if a detailed description of the best practice could be written, giving the reasons for the various steps, and issued with the endorsement of a committee composed of those who were evidently the most competent authorities. It was thought that something would be gained by clarification of the subject, and something by the eminent authority of the members of the committee. To that end, the Engineering Division appointed a committee, consisting of the gentlemen whose names follow, to mention on1y those who retained their connection with it. At this time there were serious difficulties in the manufacture, for the Government. of aircraft and high-speed engine crankshafts, of certain ordnance forgings, and of shells for both the Army and Navy. This Committee was asked to study and report upon these, with a view to betterment of practice. There were indications that the source of some of the difficulties went back to the melting of the steel and the production of the ingot. Hence, the committee first studied steel melting and ingot production, in order to guide the wartime manufacturers to an even larger percentage of useful production from the steel initially melted. Committee on Steel Ingots W. P. Barba, chairman, Ordnance Dept., U. S. A. (formerly Vice Pres. & Gen. Mgr., Midvale Steel Co., Philadelphia). George K. Burgess, Chief of Division of Metallurgy, U. S. Bureau of Standards, Washington, D. C. Henry M. Howe, Then Chairman Engineering Division, National Research Council.

Jan 1, 1922

By G. Y. Zhou

During Zijinshan copper heap bioleaching, pyrite was leached in plenty resulting in high ferric concentration in solution. It has affected bioleaching and extraction processing greatly. It results much acid and iron in solution and bad effect to extraction processing. The paper studied the influence factors in the course of pyrite leaching and ferric ion chemical oxidation, especially studied the redox potential for copper bioleaching so as to find key factors affecting the dissolution difference between chalcocite and pyrite. The results show that the redox potential is important factor. Copper and pyrite leaching rates are 95% and 11% respectively and there is great dissolution difference between them at redox potential 700 mV (SHE). During pyrite bioleaching, the indirect action of bacteria gives priority to bioleaching cooperating with the direct attack of microbial cells attached to the mineral surface. Redox potential is determined by ratio of ferric and ferrous, ferric in solution was supplied by the way of oxidation of T. f bacteria, sufficient bacteria concentration and active character were two vial factors of controlling redox potential. It is indicated that copper can be selectively bioleached during copper bioleaching by controlling redox potential of bioleaching. The conclusion will provide theoretic foundation on balance of acid and iron during bioleaching for copper of higher S/Cu ratio. The experinment proved that bacteria activation was decreased on condition of both low pH value and intermittent aeratation during bioleaching. It resulted that the oxidation velocity of ferrous ion was decreased and redox potential was controlled. The dissolution of pyrite was depressed. It would be possible to actualize selective leaching of secondary sulfide copper ore during bioleaching process.

Jan 1, 2014

Electronic Detonators have made significant strides over the last few years, both in quality of product and performance in different blast applications. The precision and flexibility of the SMARTDET units provides the mines with a powerful means of controlling blast results, giving both cost and productivity improvements. The SMARTDET Electronic Detonator System, robust and easy to use, has been successfully deployed over the last 18 months in improving mine productivity and creating safer working conditions in both quarrying and long-hole stoping. The key to the improvements has been the precision and flexibility of the electronic timing, and the ability of the mine personnel to grasp the concept quickly and use it effectively.

Jan 1, 1999

By M A. Ohsberg, A C. Robertson

Quarrying in Australia accounts for a total annual production of around 200 Mt/a of sand, aggregate and materials used in construction. This material has an annual value of the order of $2 billion and, combined with transport costs of a further $1 billion, the annual value of quarry products are in excess of $3 billion. Currently all of the production of construction materials in Australia is from open cut quarrying or dredging. This paper focuses on the extraction of material by underground mining methods, termed æunderground quarryingÆ. The paper considers a case study for future underground development expansion of the existing open cut Mt Coot-tha quarry, located 5 km from the centre of Brisbane, Queensland.

Jan 1, 1999

By William R. Barton

The domestic portland cement industry consumes more than 12 million tons annually of raw materials chemically similar to fly ash. How these materials are used and how fly ash can serve in their place are discussed. Factors influencing whether or not a particular plant will use fly ash in place of an alternate material are discussed.

Jan 1, 1968

By N. T. Rogers

An accepted statement of fact is that transportation next to agriculture is the second most important industry in the world. The transportation networks of the United States contributed immensely to the growth and prosperity of our nation. My objective is to make each and everyone here aware of the need for communication between geologists, mining engineers, purchasing agents and transportation managers. Only through a cooperative effort is it possible to reap the benefits of transportation in the industrial minerals field. Transportation is often thought of in terms of trucks, rail cars, barges, covered wagons or whatever. If this is your only exposure to the transportation industry then you probably spent most of your life in a cave.

Jan 1, 1989

By Yuri Oliveira Lima, Vitor Furlan de Oliveira, Adriano Gomes de Freitas, Ricardo Borges dos Santos, Luis Alberto Martinez Riascos

O presente trabalho, resultante da parceria público-privada entre a empresa Zeppelin Systems Latin America e a Universidade Federal do ABC, tem por objetivo validar o desempenho em termos de taxa de transporte e consumo energético de um vaso de pressão não convencional, o equipamento atua como alimentador de sólidos industrial para transporte pneumático, desenvolvido para operação de transporte de materiais em fase densa. Calcário é usado como material de deslocamento durante os ensaios no Centro de Testes da empresa, foi verificado que o novo injetor pressurizado tem menores dimensões e complexidade de operação, e possui taxa de transporte e consumo específico efetivo equiparáveis às versões de vasos de pressão convencional.

Aug 1, 2019

By Chonghun Han, Tae-Hwa Choi, Young-Hwan Chu

"A statistical optimization method is proposed to maintain stable operation in a blast furnace with stave coolers. The objective of this study is to find the operating condition which maximizes productivity as well as minimizes the heat load on the stave coolers. In this method, we first analyzed historical data and calculated the heat flux of stave coolers and the burden distribution by mathematical models. In this approach, we determined the variables to optimize and manipulated variables to adjust these response variables. Next, we collected the necessary data for the data variables after preprocessing such as removal of noise and outlier. Finally, we constructed empirical models describing the patterns of response variables in terms of manipulated variables by partial least squares regression method, and then these models were used as objective functions for entire optimization problem. By using appropriate optimization algorithm, we determined the compromised optimum operating condition considering all response variables from the past operating conditions.IntroductionBlast furnace operation which is accompanied by complex physical and chemical phenomena is an essential process for steel industry. In this process, iron ore which is charged into the blast furnace from the top goes downward. It is reduced to iron by CO gas and is melted by the heat of combustion of coke and pulverized coal. The pig iron is tapped at the bottom in liquid phase after removing the slag, which floats on the pig iron.The cooling equipment of the blast furnace wall is changed from the plate type to the stave cooler recently. In order to cool the shell uniformly and eliminate shell spray cooling, Pohang No.2 blast furnace of POSCO (Pohang Iron & Steel Company) was equipped with 11 rows of stave coolers. These staves are only 350mm-thick including the 170 mm-deep refractory on the hot face."

Jan 1, 2001

By M. Y. Wong

Electronic detonators have been used on a trial basis for over a decade, and found more recent application in production blasting as well. The relative merits of these detonators and their applicability are outlined through examples from actual blasting operations. They offer unprecedented flexibility in the design of mass blasts and in control of vibration and blast-induced damage. However, the drive towards replacing the pyrotechnic detonators by electronic ones in general could prove to be counter productive without a re-examination of prevailing blasting practices. In fact, such an approach tends to blur the tremendous potential of the electronic detonators in redefining many standard blast designs and practices.

Jan 1, 2004

By H. Vendette, N. R. Dando, A. Moras

The thorough analysis of results obtained from different testing campaigns performed on an alumina dry-scrubber pilot installation treating aluminum potline offgases, suggests a clear relationship between the emissions of gaseous fluoride and the fluoride saturation level of the alumina. The integration of this relationship into the development of a new generation of alumina dry scrubber represents an intriguing challenge regarding the design of more efficient air pollution control equipment. An innovative scheme challenging conventional industry practices was proposed. From theoretical simulations, the reduction in fluoride emissions can potentially be reduced by as much as 50% in the summer season. To validate this innovative approach, Solios in partnership with Alcoa Primary Metals, modified one of the Aluminerie de Deschambault's systems by adding new temporary equipment on the operating units and subjecting it to several test campaigns. This article presents the first results obtained in testing this new and innovative approach on alumina dry scrubbers used to capture fluoride emissions coming from aluminum electrolysis potlines.

Jan 1, 2006

By Chao Zhang, Jian Guo, Chaoquan Yao, Leige Xia, Xinyu Li, Jianliang Zhang

In this research, analytical reagents were used for the sintering experiments. And the sinters were using X-ray diffraction, scanning electron microscope and mineralogical microscope analysis to study the effect mechanism of manganese on the silico-ferrite of calcium and aluminum (SFCA) bonding phase formation during the sintering process. The results indicated that the increasing content of manganese would greatly reduce the content of SFCA, and promote the formation of calcium aluminum silicate and the amount of pores and cracks. The existence of manganese inhibited the silicon form into the SFCA and a great deal of Fe2O3 was participated in the crystal transition to Fe3O4. When the ratio of the added manganese was less than 3% in the mixing, the calcium ferrite was in substantially interleaving corrosion with hematite and magnetite. Both the porosity and silicate glass phase content were low simultaneously, which contributed to the sintering production.

Jan 1, 2015

By G J. Lyman

Sampling of grain for mycotoxins is challenging in that some mycotoxins, such as Ochratoxin A (OTA), have very low permitted levels and the kernels carrying the mycotoxin may be highly localised within the bulk of the grain as ‘hot spots’. Sampling for genetically modified organisms (GMOs) can be fraught with similar problems, especially if the contamination is adventitious and random. Incremental sampling under these circumstances can be shown to lead to a high variance in the sampling result.A new design of sampler for grain and other free-flowing particulates has been developed that is effective in practically eliminating the sampling variance due to distributional heterogeneity (DH).This paper introduces the design and argues that the sampler should be free of sampling variance due to DH.CITATION:Lyman, G J, 2017. A new sampler for grain and other free-flowing particulates, in Proceedings Eighth World Conference on Sampling and Blending , pp 277–280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

This paper outlines the position and capabilities of Western Canada's bituminous coal industry, and indicates the increasing importance of Japan as an export market. The use of coal in Japan is reviewed, especially as regards future trends, and an appraisal is made of Canadian coal in comparison with domestic Japanese coal and imports from other countries. The importance of maintaining a solid nucleous within the Canadian bituminous coal industry is emphasized. I N RECENT years, Japan has emerged as a valuable market for Canadian exports. The first major product exported in volume to Japan was wheat, which has become very successfully established in Japanese markets. Following this, iron ore gradually found a market in Japan, with exports usually based on long-term contracts. This iron ore was produced entirely in British Columbia In 1958, the Western Canadian bituminous coal industry -jointly with the Dominion Coal Board -sent an official mission to Japan to investigate the

Jan 1, 1964

By John Mahoney

We live in a world of change and the mining industry is enjoying some of the most rapid changes today that have been seen in a long time, We'd like you to open your mind to a new concept in material handling. Figure # 1 Shows a new concept combining some of the proven application advantages of the power shovel with which we are all familiar, and applies the advantages of the dragline for the benefit of the user. First, the hydraulic excavator enjoys tooth forces of the shovel because the dipper is attached to the machine with a dipperstick and boom, and can often actually realize greater tooth forces than a shovel because of the prize action of the dipper in hard digging. Second, the hydraulic excavator enjoys the application advantage of the dragline because both the operator and the machine are up above, sitting on top where the operator oversees the excavation and the machine's operating work range is greatly increased.

Jan 1, 1973

By Alessandro Navarra, Roberto Parra, Boyd Davis, Frank Mucciardi

A smelter scheduling algorithm has been developed, which allocates the oxygen production between the smelting furnace and the converter aisle, so as to maximize copper throughput. The algorithm is intended for daily operation planning, controlling the sequencing of the converter cycles, and the oxygen drawn by these cycles. In some cases, it may be worthwhile to decrease converter oxygen allocation in favour of the smelting furnaces. Thus, a better utilization of the oxygen plant can increase primary copper throughput by several percentage points. This principle is demonstrated through sample computations. The approach presented in this paper can be incorporated into smelter management software.

Jan 1, 2015

By Peter McGoldrick

This Talk ?Australian deposits in world context ?Geological setting: the importance of the basin fill ?Key deposit features using HYC (McArthur River) and Century as examples ?The difference between Aussies & Canuuks(that is between Australian & Canadian sedexdeposits!) ?Timing of mineralization ?Sources for metals and ore fluids ?What makes a super giant sedexdeposit?

May 1, 2006