Search Documents

By P. E. Wingrove

The Kayford, Boone and Nicholas Division of Bethlehem Mines Corporation operates a modern coal preparation plant in Van, West Virginia. Since the start-up of the Van Plant in 1976 until the summer of 1980, the refuse handling system proved to be a costly maintenance problem and a material handling bottleneck. During the 1980 two-week miner's vacation the original system, which included two screw conveyors and a drag conveyor, was replaced by an installation utilizing two Flexowall steep angle belt conveyors. This paper describes the technical and economic analysis that led to the new installation and reviews its first year operating performance. The Van facility is a heavy media plant designed to handle 127 mm x 0 raw metallurgical quality coal from the Powellton seam at a maximum feed rate of 590 TPH (metric tons per hour). Depending on mining conditions, the clean coal recovery rate averages between 50 and 65%. The plant is set up with three types of cleaning circuits. Coarse material (127 mm x 12 mm) is cleaned in heavy media baths. Intermediate size material (12 mm x .5 mm) is cleaned in heavy media cyclones. Fine coal (.5 mm x 0) is cleaned in a hydrocyclone1 froth flotation circuit.

Jan 1, 1981

By D. A. Pirttinen

The promotion of improved coal quality for thermal generation can benefit our national economy. The construction of electric generating facilities in Canada is expanding at a rapid rate to satisfy the demands of a rising population and new uses for electrical energy. With remaining economic water power resources in the process of development, generation from thermal sources continues to grow. The increase in thermal capability has been somewhat arrested by a de-pressed economy, widening of inter-provincial and state transmission networks and decisions to exploit certain water resources before high capital investment is further in-creased by rising construction costs. The introduction of extra high volt-age transmission lines will further delay thermal generation planning, but in due course, when the effects of restrictive factors have been dissipated, steam-electric generation from fossil fuels will rise to considerable proportions. In time, nuclear sources will contribute a growing share to thermal power, but, it is doubtful if nuclear participation will ever displace conventional fuels for steam rising, unless it can be adapted to operate efficiently for variable outputs in peaking service. It appears certain that fossil fueled

Jan 1, 1961

By Frederick Bloetscher

Means of improving the U.S. Bureau of Mines Brattice Window Method have been investigated by Goodyear Aerospace Corporation (GAC). An extensive series of laboratory tests at GAC and a series of tests in three operating coal mines of the Bethlehem Mines Corporation were conducted. The GAC laboratory tests defined the window coefficients and the accuracy of the method using different measuring techniques for a range of window sizes and shapes with window areas from 0.0873 to 4.0 square feet for flow velocities through the windows of from 100 to 1000 FPM. The results indicated that for the range of window sizes and window flow velocities investigated a single window coefficient value can be used with little error for each window size and for each flow direction, for the investigated range of window flow velocities. The mine tests developed techniques for quickly erecting the Temporary Test Stopping (TTS) in a cross-out, making the measurements, taking down the TTS and moving it and the test equipment to the next cross-cut. The time period for the total cycle ranged from 15-45 minutes depending on the properties of the cross-cut's surfaces. The total weight of the TTS and test equipment carried by the two miners conducting the tests was approximately 40 pounds. Correlation was obtained between the sum of the leakage values past 10 consecutive individual stoppings using the brattice window method and the value for the difference in the airway flow values before and after the 10 consecutive stoppings when the value for the sum of the leakages for the 10 was significant when com¬pared to the airway flow values. The mine tests reiterated the importance of using the largest TTS window(s) consistant with making accurate anemometer measurements for the best results with the brattice window method.

Jan 1, 1978

By Bradley V. Johnson

The Bureau of Mines constructed a microminer--a scaled-down (5-by 5- by 11-foot) continuous-mining machine of the drum type with a unique triaxially controlled head--for use in a research program to study the effects of continuous-mining-machine parameters on the generation of respirable dust. This report describes field research with the microminer at the Bureau's Experimental Mine at Bruceton, Pa. Experiments were conducted to determine the effects of depth of cut, rotational speed, and sump and shear rates on the generation of respirable dust. The cutting forces were also monitored and compared with depth of cut. There appears to be a reduction in the amount of respirable dust generated when the depth of cut is increased or rotational is speed lowered, Variation of other machine parameters seems to have little effect on dust generation.

Jan 1, 1975

By AIME

WE got our chance to talk with Arthur J. Blair at the Annual Meeting at the Pennsylvania Hotel. By two o'clock Wednesday afternoon things had quieted down enough so we had our interview in the foyer to the Ball Room. There were the usual questions. Where were you born? In La Salle County, Ill., on March 26, 1885. Where did you go to school? Northwestern University, B.S. degree in 1906. Where did you start work? For E. J. Longyear right after leaving school. One's ability as a geologist was measured by one's ability to wield a brush hook and ax. He stayed on the job as geologist for three years and then got to thinking about the advantages of a warmer climate. The advantages stacked up favorably, so off he went to Birmingham, Ala., just about the time U.S. Steel took over the Tennessee Coal, Iron and Railroad Co.

Jan 1, 1948

By ERNEST W. ELLIS

MORE or less contradictory findings as to the most satisfactory feed for concentration tables of the Wilfley type is shown by the diversity of opinion among experimenters. Prof. R. H. Richards,l as a result of his work, favors classification. On the other hand the work of Messrs. Cox, Gibbins, and Porter,' of McGill University, points in general to the desirability of screen-sized feed The ore used was obtained from the West mill of the Bunker Hill and Sullivan Mining and Concentrating Co., Kellogg, Idaho, and consisted of argentiferous galena in a gangue of quartzite and siderite. The natural feed was taken from the launder supplying the Fahrenwald classifier. Classified feed was collected from each of the ten spigots of this same classifier. From the natural feed the screen-sized feed was pre- pared in the laboratory. All three types of table feed were therefore derived from the actual mill circuit of a large plant.

Jan 1, 1926

By Sun Ying, Zhang Jing, Li Qiu-ju, Wang Yan-ze

Copper smelter slag was leached using sulphuric acid solutions under atmospheric conditions. Base on the composition and phase of copper slag, the effect of the concentration of sulfuric acid and leaching temperature to the leaching growth rate of Fe, Cu, Co and Ni in the copper slag were investigated in this paper. Simultaneously, the influence of sulfuric acid concentration, leaching time, leaching temperature and the amount of sulfuric acid (solid-liquid ratio) to the leaching rate of these metal elements were researched. Experimental results showed that: with the increasing temperature, the dissolution rates of the metals elements increased first and then decreased. Due to the influence of silica gel which was obtained in beginning of leaching, the higher the concentration of sulfuric acid is not conducive to dissolution of the valuable metal elements. The dissolution degree of Fe, Cu, Co and Ni were 92.83% 96.76% 93.62% and 63.41% respectively.

Jan 1, 2016

By WILFRED SYKES

THE story of the rolling of strip steel is not limited to any one plant or individual or group of individuals. It is a story with many ramifications. First of all, it should be understood that the strip mills we are considering are continuous mills, in that the steel passes directly from one mill to the other in a more or less straight line. Continuous mills are not new; in fact, they have been used for many years in the rolling of a few simple shapes. They were, however, driven by one motor through jackshafts, and as a result the speed of each roll stand had a fixed relation to that of every other stand in the series. This in turn fixed the reduction that could be made in each stand. The mill could produce simple things, but was not satisfactory for the production of the variety of strip now required. It was, therefore, necessary to get away from the restrictions of that kind of drive. To accomplish this, the designer could either separate

Jan 1, 1936

By Frans van Grunsven, Cees van Rhee, Geert Keetels

One of the obstacles during the initial phases of project development is the assessment of the environmental impact. Mining residue, consisting of fine seafloor sediments, are to be discharged subsea to mitigate the impact of these suspended particles. In order to test the effectiveness of discharging in proximity of the seabed, a numerical model is developed within the open source software package OpenFoam. Dedicated laboratory experiments for numerical model validation are discussed within this paper. INTRODUCTION Siltation is considered one of the major pressures on the environment for a seabed mining operation. Siltation is defined as the pollution of water by a high concentration of suspended sediments like clay or silt. This can be caused by two main activities during the mining process: the spill loss during the excavation and the return flow of undesired seafloor sediment after ore filtration on the ship. In a concentrated cloud, these fine particles form a so-called turbidity plume. Prediction of the size of these plumes and the created layer thickness of deposited sediment is a crucial part of the environmental impact assessment. The challenge in predicting the behaviour of these plumes is found in the wide range of scales involved in the process. At the point of origin, the turbidity plumes spread mainly under the influence of turbulent whirls created by an initial momentum and a buoyancy difference due to the presence of the suspended sediment particles. If carried by ambientcurrents, these plumes can spread for several kilometres before blending in the background.

Jan 1, 2018

By Veneta Groudeva

A pyritic ore containing zinc, lead and copper as? the relevant primary sulfide minerals, .as well as gold and silver finely disseminated in the sulfide matrix, was? leached in percolation columns. Each column contained 30 kg of ore crushed to minus 10 mm. Firstly, zinc and copper were efficiently leached by means of chemolithothrophic bacteria? in acidic sulfate bearing medium. Zinc was leached more rapidly than copper but the final extractions of these metals were similar (about 75% in 300 days). A part of the galena was oxidized to the. insoluble lead sulfate during the leaching. The pyr:ite was, however, relatively slightly attacked. The ore was then leached by means of FeC11 - HCl solutions both in the presence and in the absence of bacteria to solubilize the lead. The chemolithotrophic bacteria grew in media containing both chloride and sulfat~ ions and maintained a high ferric to ferrous ion ratio in the percoiating solutions. The chemical leaching was, however, more efficient since ft was possible to carry it out at higher chloride ion concentrations. About 10% of the lead was leached in this way in 90 days. Finally, the ore was leached by thiourea in the presence of a gold-oxidant (oxone) to extract the gold and silver. Over 60% of the gold and over 55% of the silver were extracted from the ore in 150 days, while. the extractions of these precious metals from an untreated ore sample were lower than 25%.

Jan 1, 1991

By J. A. Dos Santos

High angle conveyor (HAC®) systems in open pit mining offer many advantages over the traditional, truck only, haulage systems, including: (1) superior energy efficiency, (2) less dependency on petroleum products, (3) less sensitivity to inflation, (4) less labor, (5) less excavation for the amount of ore recovered, and (6) less ramp construction and maintenance costs. Previous studies had revealed the technical and economic feasibility of high angle conveyors. This paper presents the Sandwich Belt HAC® as the vital link to optimization of in-pit conveying systems. HAC development to date is discussed, beginning with studies in 1979, to the first large scale prototype in 1983, to the first commercial unit in 1984, into "the latest commercial installations. Discussion continues with the HAC systems to suit the various open pit mining operations and the corresponding characteristics of the system components, particularly the high angle conveyor. The range of HAC systems from the low capacity (up to 1,814 t/h), low lift (10.7 to 36.6M), highly mobile to the moderate capacity (1,814 to 3,629 t/h), moderate lift (36.6 to 76.2M), intermittently mobile to the high capacity (greater than 3,629 t/h), high lift (greater than 76.2M), semi-mobile, are discussed along with some possible combinations of these.

Jan 1, 1989

By K. Harms, T. D. Jones

TO unload large tonnages of lead bullion cast in 100-lb. bars is a problem which has confronted the lead refineries for many years. The bars, on arrival, must be restacked for unloading by truck or hand-charged to charging machines. Selected crews of labor, capable of working at sustained speeds for five- or six-hour periods, are required for this exhausting task. Due to the fatigue involved crew personnel changes rapidly. During the war it became increasingly difficult to maintain crews, especially in critical labor areas, so that the development of casting and shipping ten-ton lead blocks from the smelters to the refineries became a must in our operating program. For many years lead refineries, when making interdepartment or intradepartment transfers, have cast lead blocks weighing five or ten tons which are easily handled by crane by merely attaching the crane hook to a steel anchor embedded in the frozen lead blocks. In previous years, the practice was to use regular smelter slag pots which, due to their rounded shape, produced what were called "buttons" by the refinery personnel. The button-type blocks were unsafe as they rolled and tipped easily and were unsatisfactory for stacking since no piling pattern could be followed. To remedy this situation, flat-bottom molds came into general use and later the bottoms were made concave to prevent slipping.

Jan 1, 1946

In early March 2011, a 6.2 m (20.3 ft) diameter Rob-bins Double Shield tunnel boring machine (TBM) crossed the finish line in Sochi, Russia. The machine completed a 4.5-km- (2.8-mile-) long section of tunnel that will ultimately become part of the transportation infrastructure for the 2014 Winter Olympic Games. The TBM advanced through difficult ground at aver-age rates of 100 to 120 m/week (330 to 390 ftpw) for contractor OJSC Bamtonnelstroy, a division of the SK Most Company. The section of tunnel will ultimately become a service tunnel for Complex #3 - a section of Sochi?s transportation infrastructure under construction, which includes road and rail tunnels. A second, 10 m (32.8 ft) diameter Robbins Double Shield TBM is currently excavating the parallel 4.6-km- (2.9-mile-) long main railway tunnel using a continuous conveyor system for efficient muck removal. A 13.2 m (43.3 ft) diameter highway tunnel is also under construction. The 6.2 m (20.3 ft) Robbins TBM achieved high rates despite difficult conditions. The tunnels run through mixed ground including massive to completely fractured limestone with clay seams. Some sedimentary rock including sandstone and siltstone is present, along with fault zones consisting of breccias and conglomerates. In May 2010, the machine was stopped after encountering a significant fault zone consisting of broken rock and running soft ground. Field service personnel and crew successfully freed the machine by excavating a bypass tunnel around the TBM, freeing the cutterhead. Following the restart, a combination of continuous probe drilling and ground treatment with cement silicate and foam kept the machine moving forward.

Jan 1, 2011

By Orica Chile, Orica Brasil, Orica Brasil Victor Morais, Kinross Paracatu Leopoldo Muñoz, Kinross Paracatu Luis Marinho, Gubio Barsottini, Orica Brasil José Vergara, Lucas Steffen, Orica Brasil Washington Vilas

In drill and blast activities, it has been a challenge to sculpt walls accordingly to what has been designed in state-of-art mining design software. Obviously, the perfection of making neat and smooth walls – using aggressive sources of energy, like explosives – are time-and-money consumable and, sometimes, even unnecessary. But undoubtedly, it is vital to guarantee solid walls, safe operations environment, beyond to avoid ore losses and pit constraints caused by poor rock breakage on detonation. Kinross Gold Corporation owns the biggest Brazilian Gold Mine, located in Minas Gerais state. Morro do Ouro mine has reached over 30 years of operation, and due its mature age, the complex has developed its pits, becoming them deeper and surrounded by high walls.

Feb 6, 2023

By R. D. Hammett

This paper describes an investigation that MS carried out using the three-dimensional, stress analysis computer program "NFOLD" to assess pillar stability in relation to existing mining conditions and the proposed layout of future stopes. The stress analyses were designed to assess the present stability of the mine (particularly the pillars adjacent to the shaft), the change in pillar stresses as mining proceeds, and the optimum stope geometry to minimize ground control problems. The existing conditions were modelled first, and rock mass strengths were adjusted until a good agreement between the predicted and observed conditions was obtained. Analyses of alternative mining layouts, based on the calibrated rock mass strengths, were then compared. The paper describes the results and the conclusions of the study.

Jan 1, 1983

By Jerry Wallace

Two recent-release boulders posed serious threats to public transportation and utilities in Washington State. Both required challenging drilling and blasting solutions.

Jan 1, 1997

A Discussion of the papers of James Gayley, on "The Application of Dry-Air Blast to the Manufacture of Iron" (see Trans., XXXV., 746, 1022, also pp. 315 and 745 of the present volume, and of J. E. Johnson, Jr., on "The Physical Action of the Blast-Furnace," p. 454. Chas. B. Dudley, Altoona, Pa.:—I am not a blast-furnace man, and this always puts me at a disadvantage because I cannot go into the details of the making of iron and steel. I have not the experience, and have to take the statements of other people, so what I say regarding the subject of this paper is not in the sense of an expert. When I first heard of Mr. Gayley's experiments, I said to myself, a I fear they will result in failure, since, apparently, Mr. Gayley has forgotten one chemical fact, namely, that carbon does not combine with oxygen in the absence of mater-vapor." This fact which was so astonishing when it was first brought out some years ago, and which those who are interested may find in the Journal of the Chemical Society of London, for 1885, page 349, and 1894, page 611, led me to think that the drying of the air would be a mistake. The general subject of the influence of water-vapor on chemical action is a large one; but the special point in which we are, for the moment, interested, namely, the influence of water-vapor on the combustion of carbon, was especially treated by Mr. H. B. Baker, in the papers referred to. Apparently, however, as the result of Mr. Gayley's experiments, we are to learn that the amount of moisture still left in the desiccated air is sufficient to secure perfectly satisfactory combustion. In thinking over Mr. Gayley's paper, it occurred to me that there were two alternatives, either of which might be chosen, namely, we might dry the air as Mr. Gayley does, or possibly we might, in a very much easier way, simply saturate the air at a constant temperature, and thus get uniform working and

Jan 1, 1906

By Sheldon P. Wimpfen

Sand and gravel has been, and will continue to be, our principal construction material. Most of us are familiar with the patterns of past growth. Today we will examine the present status of this vital industry. We shall also attempt to look into the future to see where it is going and to evaluate the constraints that are being imposed. Natural aggregates are among the lowest in value of all bulk industrial minerals. From the processing point of view, sand and gravel production is relatively simple since the products are sized materials obtained from a deposit of satisfactory physical soundness. They can be used either loose or bound to provide bulk, strength, or protection. One of the main uses of coarse aggregate is in concrete as a filling material. As a general rule, the coarse aggregate constitutes about three-quarters of the volume of concrete. The other main use for aggregate is as a roadstone or roadbase to provide protective and stabilizing bulk beneath the road surface. Also it is used in a mixture with petroleum products as the wearing course on top. The sand and gravel industry is geographically widespread. In general, the output of operations is directly proportional to the amount of construction in any area. A wide variety of other aggregates compete with sand and gravel, including crushed stone, blast-furnace slag, clinker, and artificial and natural lightweight materials.

Jan 1, 1972

By L. Shuyi

In order to develop the pulsating high gradient magnetic separation technology, a type of laboratory pulsating high gradient magnetic separator (PHGMS) has been manufactured. Experiments of its separating performance were carried out. They show that PHGMS can significantly increase the grade of the magnetic product and avoid the matrix to be blocked. The characteristic curve of the pulsating fluid was measured and a formula for estimating the grade of the magnetic product was established in PHGMS.

Jan 1, 1990

By J. W. Coetzee, H. E. Deist

Carbon-in-pulp (CIP) and Carbon-in-leach (CIL) processes are used extensively in the gold mining sector to recover aurocyanide from solution. This paper discusses the modelling of these operations, using various simplifying assumptions, in order to simulate the effect of changing operating conditions on the dynamics of the system. It is assumed that the adsorption and leaching rates are a function of concentration difference between the source phase and recipient phase. The simulation was set up using Matlab's Simulink interface. Plant variables are solved using a medium scale Newtonian search algorithm in Matlab, where the differences between the actual and predicted plant outputs are minimized on a continuous time-line.

Jan 1, 2005