Search Documents

By Jose Bengoa

Low metal prices and environmental restrictions are always a challenge for copper smelters operation and its productivity. Thus, in order to reduce production costs and control gas emissions, improvements of the Teniente Converter (CT) operation were made at 110 Smelter Plant of Southern Peru Copper Co., 110, Peru, and the main objective was to increase its capacity for smelting copper concentrates without affecting normal operation. The present work corresponds to a recent study conducted during the normal industrial operation of the Teniente Converter in this plant and, it shows the effect of increasing air oxygen enrichment from 28 to 34% on its productivity. The results show an increasing of concentrate smelting rate from 800 to 1370 tpd and hence a notorious improving in copper production, and practically no effect on the refractory consumption. The increment of the concentrate throughput, increases also the SO2 concentration and the sulfuric acid production, showing the effort done by this operation in order to accomplish the environmental Peruvian regulation.

Jan 1, 2003

By E. Tarshizi

This research project demonstrates the application of a mine system simulation and animation model in enhancing the efficiency of a truck-shovel operation and reducing the haulage environmental impact in an open-cut coal mine. In any mine, a key objective is to have enough equipment for production and not have excess to where it is counterproductive. Due to the advent of responsible mining, environmental regulations, and eco-friendly practices, these factors must also be considered in the analysis. The over-trucked situation at a mine will be discussed, i.e. when the number of trucks exceeds the optimum number of trucks a mine should have for the most productive/profitable mining operation. When the system has an excess number of trucks, truck utilization is reduced which impacts mine operation, capital costs and the environment, through unnecessary truck purchase, energy use, air pollution etc. A hypothetical surface coal mine layout was used for the simulation model.

Feb 23, 2014

By J. T. I. Poijärvi

The smelter off-gas cleaning and the weak acid treatment at Outokumpu Harjavalta Metals Oy are presented and described in this paper. The smelter consists of the copper and nickel smelters and the acid plant of three separate acid plants two of which are double contact and one single plant and of one liquid sulphur dioxide plant. The preliminary cooling and flue dust separation of the smelter off-gases from the copper and nickel flash smelting furnaces and converters in the waste heat boilers and in the hot electrostatic precipitators are described. The final cooling and cleaning of the gases in the scrubbers at the sulphuric acid plant and the treatment of the weak acid in the vacuum and in the submerged combustion evaporators for the removal of impurities are pre¬sented as well as the treatment of the condensates from the evaporators. The attention is paid to the generation of sulphur trioxide in the smelter off-gas and to the treatment of that in the weak acid bleed-off and to the utilization of the treated acid.

Jan 1, 1992

By A. W. Khair, L. D. Gehl

"This paper describes the study of bit wear characteristics on three types of rock namely Tennessee sandstone, Berea sandstone and Indiana limestone. High content of quartz with quartz cement in Tennessee sandstone causes removal of material from the bit body and dam2ge to the tip of the bit resulting into excessive weight and height loss as compared to other two types of rock. The drum speed and water spray pressure do not contribute significant effect on bit wear. The polycrystalline compact diamond (PCD) tipped bits are more wear resistant than the ordinary tungsten carbide (WC) tipped bits, but, due to wider body of PCD bits, the wear rate increases particularly at greater depth of cut. INTRODUCTIONThe impact of bit-rock interaction during the cutting process in underground coal mines has always attracted the-interests of mining operators, researchers and the manufacturers. Coal cutting bears directly on airborne coal dust generation which causes ""black lung"" in coal workers. On the other hand, rock cutting generates frictional sparks causing face ignitions. The bit wear not only produces airborne rcspirable coal dust , but also affects the productivity, safety and economy. Hun and Evans (J) concluded that the point attack bits have greater ignition potential than the conventional wedge shaped bits. The results of a study (2) suggested that after 7% of weight loss, the bit should be replaced. In a survey study (3), it was found that the bit consumption of bit had an effect on the productivity and utilization of the continuous miners. The mining industry is yet to receive a solution which could provide them with optimum operating parameters for coal cutting machines in underground C9al mines.The study was, therefore, taken up to determine wear characteristics as influenced by the rock propenies and varying operating parameters. For the purpose of this study, three types of rock, Tennessee sandstone, Berea sandstone and Indiana limestone were used. The machine operating parameters included (i) drum speed, (ii) water spray pressure and (iii) bit type. Besides studying the wear characteristics, the effects of these parameters on the required cutting force, specific energy consumption, acoustic emission generation and bit temperature rise were also studied. Also, the preliminary experiments were performed to compare the bit wear between PCD and WC tipped bits."

Dec 1, 1995

By Andrew Campbell, Michael Reed

"WorleyParsons has used Discrete Event Simulation methods in conjunction with more traditional process models to assess the performance of copper smelting operations. This work was performed to determine the plant capacities and suitability of proposed debottlenecking options including accounting for the planned and unplanned (breakdowns) shutdowns in the various parts of the plant and supply chain. This paper outlines the methods used along with demonstrating the benefits of selecting a feasible option and minimizing capital and operating costs.IntroductionTraditionally for de bottlenecking studies of smelters and other process plants, a mass balance is performed based on continuous operating rates and expected operating hours. Smelters have several points of failure that will restrict, if not take the entire plant offline. By using a more detailed model, validated against plant experience, bottlenecks can be demonstrated and strategies to remove them to increase plant availability and economic.The modeling simulates the plant performance in real time, and by performing enough simulation the expected long run performance of the plant can be estimated. The models have been built using ExtendSim which is a powerful Discrete Event Simulation software package that is ideally suited to the batch and semi-batch processes and events that occur within smelter operating environments. The value of performing this work is that the operational performance of the plant can be assessed ensuring production targets are met, without using excessive capital outlay."

Jan 1, 2013

By Robert K. Guthrie, James W. Amyx, D. B. Taliaferro

"INTRODUCTION Secondary recovery of oil by water-flooding is practiced more extensively in North Texas than in any other section of the State, and the progress and experience of the operations in that area are of continuing interest to all branches of the oil industry. The first Bureau of Mines report on water flooding in North Texas 7/ chronicled the activities from December 7, 193f', when the Railroad Commission of Texas granted The Texas Co. the first permit to inject water into an oil-bearing sand, through 1944. This second report has been prepared as a supplement to Report of Investigations 3906 to show the progress and expansion of water-flooding. The format of this report is almost identical with what of report of Investigations 3906, except for a few miner changes. For the sake of brevity, certain basic information contained on the first report has not been repealed, and the reader is urged to consider the two reports as corporation writings.The North Texas area, as encompassed by the two reports, corresponds Railroad Commission of Texas Districts 7P and 9. Oil-development operations in the two districts, since oil was discovered in 1904, have resulted in the recovery of approximately 1,400,000,000 barrels of oil from a proved area that has been estimated to exceed 413,000 acres. During October barrels of oil was produces by primary and secondary-recovery methods from 1,746 flowing wells and 25,211 pumping wells, a daily average 6.6 barrels per well. Of this total volume of oil recovered in October 1947, 47,965 barrels (0.87 percent) was recovered from leases on which water-flooding operations were in progresses."

Feb 1, 1948

By H Q. Zhang, M C Chai, W Fu, H Y Chen, L M. Wei, Q J. Yang

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Fozichong deposit – located in the south-western segment of the giant Qinhang metallogenic belt, South China – is a large-sized lead-zinc polymetallic deposit. This deposit contains two main ore districts, termed as the Guyi ore district in the north and the Hesan ore district in the south respectively. We present an integrated data set on sulfide minerals, fluid inclusions and stable isotope (H-O-S-Pb) geochemistry to better understand the features and genesis of the Fozichong deposit.Field and paragenetic relationships indicate three mineralisation stages forming the early (Po+Sp+Gn+Ccp+Py+Di+Ep+Qtz), middle (Sp+Gn+Ccp+Py+Ep+Chl+Qtz) and late (Gn+Sp+Py+Qtz+Cal) sulfide assemblages respectively. Mineral chemistry – particularly S/Fe and Co/Ni ratios in pyrite, Zn/Fe, Zn/Mn and Zn/Cd ratios in sphalerite and Pb/Ag ratios in galena – indicates a magmatic association for the sulfide minerals.Quartz and calcite coexisting with the sulfide minerals of various stages host abundant fluid inclusions. Quartz in the early stage contains two- or three-phase CO2-H2O and liquid-rich aqueous inclusions, which have homogenisation temperatures of 162~365°C and salinities of 2.9~17.8 wt per cent NaClequiv, whereas quartz and calcite from the middle and late stages are dominated by two-phase, liquid-rich aqueous inclusions that have slightly lower homogenisation temperatures (153°C~320°C) and much lower salinities (1.0~6.0 wt per cent NaClequiv). Hydrogen isotopes (dD = -59‰~-41‰), analysed using fluid inclusion waters from quartz and calculated oxygen isotopes (d18OH2O = -5.47‰~4.00‰) for the equilibrated ore fluids, indicate that the ore-forming fluids may have been sourced from magma and mixed with groundwater in the late stages. Sulfide minerals have d34S values of 2.3‰~4.3‰, consistent with a magmatic-derived source for sulfur. Lead isotopes (206Pb/204Pb = 18.592~18.794, 207Pb/204Pb = 15.648~15.864, 208Pb/204Pb = 38.909~39.580) confirm that lead and, by inference, zinc were mainly derived from magmatic rocks, with subordinate contributions from sedimentary rocks.Various lines of evidence support that the formation of the Fozichong deposit has close genetic association with the granite porphyry intruded in the late Yanshanian period (106 Ma), and it can be classified as a magmatic hydrothermal type lead-zinc deposit. We propose that the Hesan and Guyi ore districts may represent the proximal and distal products of a magmatic – hydrothermal system respectively.CITATION:Fu, W, Zhang, H Q, Chai, M C, Yang, Q J, Chen, H Y and Wei, L M, 2015. Genesis of the large-sized Fozichong lead-zinc polymetallic deposit, Guangxi, south China – constraints from the sulfide mineralogy, fluid inclusions and isotope geochemistry , in Proceedings PACRIM 2015 Congress, pp 609–614 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By M Reza Afshar

In this work a mathematical model was developed to study the effect of electromagnetic force on the magnesium melt containing nonmetallic inclusion in an electrical isolated channel. The electromagnetic force exerted on the inclusion induced by DC current field was calculated. A three dimensional turbulent flow equations were solved numerically to compute the velocity field within the channel. On the basis of computed velocity and magnetic fields, the trajectories of inclusions were calculated using the equations of motion for inclusions. Parametric studies were carried out to evaluate the effect of various parameters such as current density, channel diameter and particle density on the removal efficiency of inclusions from magnesium melts.

Jan 1, 2004

By Haofeng Xie, Lijun Peng, Xujun Mi, Xue Feng, Xiangqian Yin, Zhen Yang, Guojie Huang

The Cu/Al composite wires have been widely used in cable industry. Especially in the development of aerospace, the light weight character of wires is particularly important. The wires are fabricated by a drawing process and heat treatment. Mechanical and electrical properties are measured and analyzed. The bending behavior is studied by scanning electron microscope. INTRODUCTION Cu/Al composite is a typical bimetallic composite that has been used in plenty of fields such as automobile and aerospace. The composite has the advantages of excellent conductivity as well as low weight, which cannot be obtained from single copper or aluminum. Industrial products of Cu/Al composite include Cu/Al composite joints (Uscinowicz, R., 2013), Cu/Al bimetallic sheets (Li, X. et al., 2011), Cu/Al flat bar (Wu, Y. & Liu, X. & Xie, J., 2014) and CCA wires (Ahmed N., 1978). CCA wires refer to the composite wires that copper layer concentrically coated on the surface of aluminum core conductor, implementing solid combination of two metals on the interface and forming an integral. At present, the aircraft cable generally use copper or copper alloy conductor, which makes the wire in the aircraft occupy a considerable proportion due to the large density of copper. Therefore, the use of Cu/Al composite wires instead of copper wires for weight loss, is of great significance to the development of aerospace technology industry. Heat treatment is an indispensable procedure to improve plasticity during cold working process, which is of great importance to preparation of wires (Wang, Q. et al., 2008). During the heat treatment, the Intermetallic Compounds (IMCs) are inevitable formed at the contact area of Cu/Al due to the occurrence of diffusion (Lee, S. et al., 2012). According to the results of former researchers, kinds of IMCs were discovered. Antoine Gueydan (2014) identified the formation of three IMCs (Al2Cu, AlCu, and Al4Cu9) at the interface between copper and aluminum after thermal aging. IMCs have a significant effect to the properties of Cu/Al wires. Bending performance is a vital property for the actual application of wires. The brittle IMCs may create a stress concentration that can cause crack initiation during bending process. This work focus on the mechanical properties of Cu/Al composite wires after heat treatment. The effect of various annealing condition on mechanical and electrical properties are studied, in order to find the appropriate annealing conditions, which produce optimal combination properties of Cu/Al clad composite wires. Bending fracture of composite wires is discussed by morphology observation.

Jan 1, 2019

By D. R. Wright

"The modest thermal efficiency of the steam turbine cycle essentially determines the heat required and, therefore, the coal consumption and ash production of pulverized-coal-fired powerplants. This paper emphasizes how some properties of coal and its ash can crucially affect the operation of a steam generator and its flue gas cleaning equipment. A brief reference to some siting factors and economics reaffirms the all-pervasive influence of the properties of coal and ash and establishes the importance of a firm supply of cooling water. The economics of scale remains a compelling factor in selecting the size of units, despite disappointing performances by some of the larger units. Environmental considerations suggest that smaller units still have a role to play. IntroductionCoal fuelled one industrial and economic revolution, beginning two hundred year s ago . It was the precursor of competing fuels, notably natural gas, oil and uranium, which eclipsed it in terms of convenience and rate of growth.The turmoil that now exists because of rapidly dwindling supplies of no-longer-cheap oil and the concerns about nuclear energy-justified or unjustified-exacerbated by an operating incident at the Three Mile Island Nuclear Powerplant, prompt speculation for a resurgence of coal, especially where it cangenerate electricity to replace energy from imported oil.The world's reserves of coal are not inexhaustible, although they are ample for several decades. Of greater import is the fact that the world's coal reserve s are more widely distributed than its oil reserves, and they appear less convenient as instruments of economic and political persuasion by opportunist powers. The crux is whether or not the world will accept all that a massive, if temporary, return to coal implies.Combustion of pulverized coal in steam generators to pro duce electricity is a 50-year-old, well-understood technique; it is undergoing continuous refinement to meet evolving environmental and economic criteria and is not found wanting. It is certainly the only technique available and technologically advanced enough to replace oil immediately on a large scale. Although it may take a decade to bring a new coal-fired powerplant into service, this delay is a reflection on nontechnical and administrative processes. Capital and operating costs of coal-fired powerplants are significant and subject to inflation, but, because of the accumulated experience in this field, the ability to control costs is better than for those energy processes which are less mature or still in embryo form. More exotic, soft energy systems, touted as the panacea for world energy problems, have still to prove themselves on the scale they are needed and under the stringent climatic and operating conditions coal-fired powerplants have already mastered."

Jan 1, 1980

By AIME AIME

WHEN Vice-chairman Calvert Townley calls the next meeting of the Executive Board of the American Engineering Council of the Federated American Engineering Societies to order in Washington on Sept. 30, it will be the first meeting in that city for almost a year. It is probable that the Board will decide at this meeting whether future board meetings will be held regularly at the headquarters in Washington or whether the plan of meeting at various engineering centers throughout the country, as has been done during the past year, will be followed. The most important business coming before this .meeting will be the election of a president to succeed Herbert Hoover, who resigned after he became Secre¬tary of Commerce. Nominations to fill this vacancy were ordered 'at the last meeting of the Executive Board, to be reported at the September meeting. Special attention will be given the plans for the engineering assembly, extension of employment service, question of licensing and registration of engineers. The engineering assembly, committee has been appointed, with A. P. Davis as chairman, the other members being Philip N. Moore, L. P. Alford, John C. Hoyt and F. A. Vaughn. This committee will work out detailed plans for an assembly to be held in con¬junction with the annual meeting of the American Engineering Council in, January. Tentative plans provide for a three-day session; one day to be given to special meetings of the executive boards of member organizations and committees of the American Engineering Council; one day to the sessions of the American Engineering Council; and at least one day to discussion of some, special topic.

Jan 1, 1921

By Heng Yi

The salt lake brines that lithium is extracted from have high chloride levels making the brine very corrosive to stainless steel extraction column internals. This is a significant problem in column scale-up to industrial production. Two types of corrosion-resistant ceramic internals, the hybrid ceramic internal and ceramic plate, were designed and tested under pilot conditions for future industrial application in this field. The hydrodynamic results (Yi et al. Ind Eng Chem Res 56 (4):999–1007 (2016), [1]) show that holdup of hybrid ceramic internal is higher than that of ceramic plate by around 50%, while Sauter mean diameter when using the hybrid ceramic internal is smaller than when using the ceramic plate by around 30%. This results in a larger mass transfer area, hence better mass transfer efficiency for the hybrid ceramic internal. Axial dispersion and mass transfer parameters are also examined (Yi et al. Ind Eng Chem Res 56(11):2049–3058 (2017), [2]). The results show that the column with hybrid ceramic internals has 50% lower axial dispersion coefficient and 50% higher mass transfer coefficient, leading to higher mass transfer efficiency. The transfer unit height of the column using hybrid ceramic internals can be as low as 0.2 m, showing very good efficiency. This is promising for near-future applications. Two-phase computational fluid dynamics (CFD) models have been developed for the two columns with ANSYS FLUENT commercial software. CFD successfully predicts the higher holdup and lower axial dispersion coefficients for the hybrid sieve plate pulsed column as measured in the experiments, and the cause for the difference in performance has been explained with information from CFD.

By G. C. Li

Gold extraction using iodide leaching from refractory carbonaceous gold ores was studied. Thermodynamic analysis of iodide leaching chemistry had been carried out. Eh-pH diagram of Au-I2-I--H2O leaching system showed that the coordinating active forms from iodides were I3- and I-, while the major coordinate compound formed during iodide leaching was AuI-. For leaching parameters optimization, technological parameters such as I2 concentration, I2 :I- ratio, oxidation assisting agents, liquid/solid ratio, and leaching duration were studied. The leaching results showed that the average Au leaching rate reached 91% and 92% for oxidized ore and roasted primary ore respectively. Leaching process proceeded in weekly acidic or neutral slurry at ambient temperature; the leaching duration was 4 hours. After that gold was extracted from the pregnant liquor by activated carbon adsorption ? desorption ? electrowinning process. Gold recovery was over 93% in the adsorption process, while the gold recovery in electrowinning process was about 95%, provided that the initial gold concentration is 40mg/L or larger. For iodine regeneration it is enough to add hydrogen peroxide in excess into the filtrate after gold electrowinning, all the iodides existing in the solution in any forms would be precipitated in the form of elemental iodine.

Jan 1, 2014

By Florian Kongoli

"Lime ferrite" slag with limited silica content has proven to be a valuable choice in the modem processes of copper smelting and converting due to several advantages that this slag offers compared to classical silicate slags. Nevertheless the liquidus surface of this slag has been experimentally measured only at low oxygen potentials such as in equilibrium with iron or near it and in air. Although most of the smelting and converting processes that use this slag occur at intermediate oxygen potentials, the liquidus surface of this slag is not known at these conditions and the effect of oxygen potential and silica has not been correctly understood. This has brought some confusion in literature as well as in the industrial practice. In this work the liquidus surface of the calcium ferrite slags has been quantified by the means of a new thermophysicochemical model and a new type of liquidus surface diagrams which are very convenient for any industrial process that uses calcium ferrite slags. These diagrams can be easily used to select the lowest liquidus temperature of calcium ferrite slags at a minimum cost and can help design several fluxing strategies in copper smelting and converting processes. The effect of the oxygen potential and silica is also quantified and important industrially related conclusions are drawn.

Jan 1, 2003

By Florian Kongoli

"Lime ferrite" slag with limited silica content has proven to be a valuable choice in the modem processes of copper smelting and converting due to several advantages that this slag offers compared to classical silicate slags. Nevertheless the liquidus surface of this slag has been experimentally measured only at low oxygen potentials such as in equilibrium with iron or hear it and in air. Although most of the smelting and converting processes that use this slag occur at intermediate oxygen potentials, the liquidus surface of this slag is not known at these conditions and the effect of oxygen potential and silica has not been correctly understood. This has brought some confusion in literature as well as in the industrial practice. In this work the liquidus surface of the calcium ferrite slags has been quantified by the means of a new thermophysicochemical model and a new type of liquidus surface diagrams which are very convenient for any industrial process that uses calcium ferrite slags. These diagrams can be easily used to select the lowest liquidus temperature of calcium ferrite slags at a minimum cost and can help design several fluxing strategies in copper smelting and converting processes. The effect of the oxygen potential and silica is also quantified and important industrially related conclusions are drawn.

Jan 1, 2003

By N. J. Sather

A detailed description is given of Bunker Hill's concentration process employed at the company's lead-zinc property in the Coeur d'Alene district, Idaho. The plant is equipped to process 3000 tpd of Pb-Zn ore. The history of the Bunker Hill mine dates back to Aug. 26, 1885, when Noah S. Kellogg found the outcrop of the Bunker Hill orebody on the hillside of Milo Gulch above the present town of Wardner, Idaho. A small concentrator was erected in 1886, and before the railroad came, the mine output was transported by mule teams to the head of navigation on Coeur d'Alene Lake. After ten years of production, an interest was purchased in the Tacoma smelter at Tacoma, Wash., to which the entire output was shipped. In 1916 and 1917, a modern lead smelting plant and refinery was erected, and a modern electrolytic zinc reduction plant was built in 1927-1928 by the Sullivan Mining Co. which was 50 pct owned (and now totally owned) by the Bunker Hill Co. The first concentrator, a 100-tpd capacity plant, was built in 1886 near the Reed Tunnel in Wardner. The treatment consisted simply of crushing ore to 2 in. and then to 1/2 in. through rolls in closed circuit with a bucket elevator and trommel screen. The undersize was further sized in trommels to 10 mm and 3 mm. Oversize from the latter was treated in Hartz jigs. The 3 mm undersize was classified in crude hydraulic classifiers furnishing sands to sand jigs, the overflow being dewatered in a long V tank which supplied sands to a Cornish buddle and to Frue vanners. The concentrates were of excellent grade, old records showing assays of 69 pct lead and 29 oz. of silver per ton. Tailings were high inasmuch as the provision for treating the slimes was inadequate. Since the erection of the first mill, the Bunker Hill plant has gone through many changes and improvements. In succeeding years, the flowsheet was enlarged somewhat with Huntington and Chilean mills, vanners, tables, ball mills, and flotation cells being progressively added. In the transition period to the present day practice, the object was not only to improve the equipment for better mechanical performance, but to add new equipment whenever practicable so as to improve both grade and recovery of the product at a lower cost. For the modern plant and flow-sheet, see Figs. 1 and 2. The history of flotation at Bunker Hill dates back to 1913 when experimental work was done in a cell in which the pulp was circulated through a centrifugal pump set outside the cell and discharged against a baffle in the cell. The cell was built with a spitzkasten, and the quiet zone in the latter tended to let the froth break down before it got to the overflow weir. To remedy this situation, a belt drag with light metal flights was arranged for drawing off the froth over a ramp in each cell. Recovery of lead was not as high as present day practice, but was so much better than the vanners that the cells were multiplied gradually to eight cell units. The mill men called them mud hens. Flow between the cells was controlled by a weir, which determined the pulp level in each cell. These early machines were called Bunker Hill machines. The tailings were later treated in pneumatic scavenger flotation machines in a series, producing concentrates for retreatment in the Bunker Hill cleaners as well as the final tailings. This system of flotation served with minor changes until the Fahrenwald machine was developed at Bunker Hill during the period from 1921 to 1925. In 1925, the Fahrenwald flotation machine gradually replaced the Bunker Hill machine, although the Hearing pneumatic scavengers for retreatment of the tailings from the Fahrenwald machines were retained in the lead section until 1928. The use of the Hearing pneumatic machine for cleaning the rougher concentrates was begun in 1924. In 1941, plans were made for remodeling and modernizing the concentrator, the goal being a modern concentrator employing the latest equipment and milling practices. The old wooden building was to be replaced by a steel and concrete structure. Shortly after preliminary work got under way, the United States entered World War II and the demands for metals increased. To meet this requirement, the management decided to increase the capacity of the concentrator to 1800 tpd. This was accomplished in record time by the construction and operation of a sink-float plant. Installation of this plant was the first step in the general plan for modernization. In 1947 the concentrator (including the sink-float plant) was enlarged to handle 3000 tpd. Milling operations today are at the rate of 2300 tpd, five days per week. During 1959, 453,000 tons of ore was beneficiated. The Bunker Hill concentrator is in three sections: the crushing plant, a 3000-ton capacity storage bin, and the concentrator building. The crushing plant is of wood design with a gunnite coating on the exterior.

Jan 1, 1961

By C. H. Mathewson

THIS paper was prepared upon request as a contribution to a symposium covering the manufacture, properties, and uses of the important non-ferrous metals. In approaching a subject as broad as this, there is a natural desire to build up a comprehensive and finished production which shall constitute a dependable source of information on all questions properly belonging to this branch of metal technology. There are, however, a number of circumstances, apart from the mere routine of labor and thought involved, which operate rather effectively against the possibility of completing such an ambitious program at the present time. First of all, as far as any public record of results is concerned, the commercial rolling, drawing, and forming of zinc with relation to changes of structure and properties-and this we consider to constitute the elements of metal technology-might as well be an unpractised art. We have never seen a published photomicrograph showing the structural characteristics of either hard or soft sheet or strip, although the structure of castings has been frequently described, and other coarse-grained structures resulting from hard-hammering and annealing have been reproduced. Thus, an author in this field must proceed to his task without much assistance from the literature, and the outcome can represent only a personal estimate of principles, facts, or findings, and not a summary

Jan 9, 1919

By Edgar W. Sawyer

Attapulgite and sepiolite are the clay minerals used to thicken ionically contaminated watzrs in the preparation of drilling fluids. They are nonsweliing clays that can be dispersed and reflocculated by mechanical means to increase the viscosity of fresh water and salt and gypsum contaminated waters. Those gelled in fresh water do not become excessively thick when contaminated with high salt concentrations or polyvalent cations encountered during drilling. Gels formed exhibit thixotropy and yield pseudoplastic rheological behavior due to the particle interactions and mechanical interferences of the flocculated gel structure.

Jan 1, 1983

By Naiyang Ma

Along with fast growth of EAF steelmaking, better ways of treating EAF dust have been continuously pursued for better environmental protection and better economic benefits. In this contribution, various ways of collecting EAF dust in EAF off-gas cleaning systems are reviewed, and generation of dust and concentration of zinc in the dust from various collecting devices are examined. Accordingly, recycling of EAF dust through source separation is discussed.

Mar 1, 2018

By P J. Sack, L V Danyushevsky

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Regional-scale exploration for sediment-hosted gold deposits is hampered by the challenge of evaluating the fertility of ancient sedimentary sequences that host these deposits. Recent developments in laser ablation inductively coupled plasma mass spectrometry allow for the evaluation of the gold fertility of sedimentary sequences using chemistry of early-formed sedimentary pyrite. We present a case study from the Selwyn basin area of Yukon, Canada, where significant sediment-hosted gold exploration has been ongoing for the last five years. Data from sedimentary pyrite in some Neoproterozoic shales are anomalous in Au and As compared to a global data set of unmineralised sedimentary pyrite. If at least some of the gold and associated trace elements in sediment-hosted gold deposits are derived from recrystallisation of early sedimentary pyrite, it follows that strata containing anomalous sedimentary pyrite should be more prospective. Based on this premise, our data clearly show that Yusezyu Formation Neoproterozoic shales in the Selwyn basin area of Yukon are a fertile source rock for sediment-hosted gold deposits, while pyrite from Nadaleen formation shales are strongly anomalous in Hg and Tl, but not Au. We suggest that the area warrants continued exploration for sediment-hosted gold.CITATION:Sack, P J, Gregory, D D, Large, R R and Danyushevsky, L V, 2015. Using sedimentary pyrite chemistry to inform regional exploration for sediment-hosted gold deposits – a gold fertility case study from the Selwyn basin area, Yukon , in Proceedings PACRIM 2015 Congress, pp 69–76 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015