Search Documents

By D. P. Ziegler

Formulas relating economic optimum busbar cross sectional areas to busbar cost, electric price and financial parameters are reviewed and revised. Application of the formulas is illustrated with discussion of the appropriate choice of parameter values and the sensitivity of the optimum to the parameters. The extension of the single busbar concept to optimization of more complicated arrangements of bus for smelting pots is complicated by the constraint of obtaining a specified current distribution. An example problem illustrates the optimization of a section of a bus network containing a fork, with the imposed limitation of achieving a specified uniformity in the current. In cases where the current in the individual conductors may vary, Kelvin's law does not apply. Further extension of the technique to a full pot set of conductors poses additional problems which are discussed, but whose solution has not yet been accomplished. Aluminium 2006 45th Annual Conference of Metallurgists ofCIM Montreal, Quebec, Canada Edited by

Jan 1, 2006

By J. W. Cash

The mineralogy and textures of cyclone dust, sludge, and occasional build-ups in the American Iron and Steel Institute (AISI) direct iron making pilot plant at Universal, Pennsylvania have been studied by reflected light, transmitted light, and cathodoluminescence microscopy, and phase compositions have been determined by SEM-EDS. The cyclone dust consists of particles of carbon, metallic iron, sulfur-bearing iron, and wustite. Measurements of particles in the sludge indicate that 69% are less than 2.5 µm across, 21 % are 2.5-5 µm, and 10% are larger than 5 µm. Mineralogically the sludge particles are mainly carbon and metallic iron, with minor wustite and sulfur-bearing iron. Build-ups that sporadically develop in the furnace consist of olivine, hercynite spinel, metallic iron, wustite, pyrrhotite, pseudobrookite, akermanite-ferroakermanite and gehlenite. The microtextures shown by the build-ups indicate that much of that material has precipitated at the build-up loci. This study has been supported by AISI and the U.S. Department of Energy.

Jan 1, 1995

By J. N. Hartley

Samples of ash from the May 18, 1980, eruption of Mt. St. Helens Were collected from several locations in eastern Washington and Montana. The optical microscope and the combined scanning electron microscope with energy dispersive x-ray microprobe were used to determine the composition and mineralogical characteristics of the samples. In addition, a quantitative image analyzer was used to examine the particle size distribution, and x-ray diffraction was used to identify major minerals. Both polished sections and ultra thin sections (less than 5 ~m in thickness) were prepared to study the mineralogical characteristics. The use of ultra thin sections provided access to microstructural detail. Mineralogically, the samples ranged from almost totally glassy to almost totally crystalline. Crystal-line samples were dominated by plagioclase feldspar (andesine) and ortho-pyroxene (hypersthene) with smaller amounts of titaniferous magnetite and hornblende. Nearly all the samples contained from less than 1 to 3 wt% free crystalline silica (quartz, trydimite, or cristobalite).

Jan 1, 1981

By Adriane Lopes Mougo

Super duplex stainless steel presents a biphasic structure composed by ferrite and austenite with different characteristics and properties. In the micromilling process the cutting edge radius has similar dimensions to the grain size. The biphasic structure found in this material could influence on the cutting tool life and the surface integrity of the workpiece. Due to its low machinability, caused by high hardening level and low thermal conductivity, the process can produce built-up edge and high surface roughness (Ra). In this work it is performed an experimental study of the micromilling of super duplex UNS 32750 and the influence of the cutting speed (Vc) and feed per tooth (fz) on the surface integrity and tool wear. The design of experiments considered two levels and three replicates. Results indicate the increase of roughness for bigger feed per tooth, small influence of the cutting parameters on the burr formation. The tool presented flank wear after the experiments.

Aug 8, 2018

By F. E. Brantley, D. A. Martin

Synthetic zeolites were tried as selective adsorbents for recovering sulfur dioxide from synthetic gases and gases produced from gypsum decomposition . Initial adsorption tests , using the synthetic gases , indicated that three of these compounds , having sulfur dioxide capacities of up to 29 grams per 100 grams of adsorbent , were satisfactory . Regeneration studies showed that over 90 pct of the sulfur dioxide desorbed from the loaded beds was of sufficient purity for direct liquefaction . However , all zeolites tested lost adsorptive capacity with repeated use . The zeolite determined to be the most promising in the preliminary synthetic gas tests was also evaluated for capability in adsorbing sulfur dioxide from gases produced by the thermal decomposition of gypsum . Despite small amounts of hydrogen sulfide in the gypsum decomposition offgas , good adsorption of sulfur dioxide was attained . The economic practicality of utilizing zeolites for sulfur dioxide removal from industrial gases was not evaluated , but the technical feasibility was demonstrated .

Jan 1, 1963

By X. Xu, J. K. -W. Wong, J. -Y. Delenne, K. Soga

Hydraulic fracturing (HF) is a mulit-scale and multi-physics process which makes numerical modelling challenging. Conventional numerical models focus on multi-physics nature of HF but the multiscale nature is compromised by idealization of reservoir to be continuous, homogeneous and isotropic. However, natural fractures take a significant role in the success of HF for exploration of unconventional resources like Shale gas. Advancement in microseismic monitoring provides useful data for simulation in a much greater details. There is an urgent need to develop a suitable numerical tool for multi-scale threedimensional simulation to better understand the roles of discontinuities and heterogeneity in reservoir and its interaction with HF, especially to address the environmental concerns such as induced seismicity. In this paper, a simple discontinuum numerical method – Lattice Element Method (LEM) is proposed to model HF in a large scale three-dimensional model. A reservoir is modelled as a lattice network composed of 1D Hookean’s spring. Fracturing is modelled simply by removing lattices that meet a specified threshold as determined by the critical energy release rate of the rock. By introducing disorder in the model, mesh dependency in modelling fracture growth is minimized. Fluid flow is simplified as flow in pipe network and the permeability of pipe is related to fracture aperture by cubic flow law. Therefore, fracture flow and rock deformation are fully coupled. In this paper, four simulations of the same configuration except with different degrees of reservoir heterogeneity are presented. Fractures formed are diffusive and two groups of fracture are identified – connected fractures and isolated fracture without clear spatial correlation. The former forms a ‘fracture cloud’ and contributes to fluid flow and modeled by pipe network. The flow of fluid is highly tortuous and pipe network is sparely connected. The degree of reservoir heterogeneity controls the growth of ‘fracture cloud’ and pipe network. Microseismic monitoring often shows diffusive fracturing during HF on site and hence the outcome of the proposed model can be compared to such monitoring results.

Jan 1, 2015

By B McFadzean, N P. Lima, D A. Deglon

The reverse flotation of Itabirite iron ore is typically performed after a desliming step in which most of the sub-10 µm particles are removed. This is done to limit processing problems such as poor flotation recovery of SiO2 due to slime coatings and increased slurry viscosities, unmanageable froths and increased losses of hematite particles due to entrainment. However, the rejection of ultrafine particles contributes to large losses in iron recovery and may contribute to the instability of tailings dams. The aim of this study is to decouple the effects of ultrafine particles in the pulp and froth phases to better understand the processing capabilities of the fines fraction. The flotation test work was performed in a special-purpose continuously operated laboratory flotation cell that has a deep froth section to simulate plant-scale froth conditions. Five conditions of fines addition were investigated at three different froth heights and a solids concentration of 50 per cent. The behaviour of the pulp and the froth were decoupled using froth stability and froth recovery tests. This showed that, even though there is an exponential increase in froth stability at increasing fines quantities, the performance of the pulp has the overriding effect on the overall SiO2 recovery. Pulp zone, froth zone and overall SiO2 recoveries showed that overall recoveries increased by about 3.6 per cent for every 1 per cent decrease in fines content. This meant a large increase of 20 per cent in SiO2 recovery when going from undeslimed to deslimed feed. This was driven largely by increases in the pulp zone recoveries, which were about 4 per cent for every 1 per cent decrease in fines content. The froth recoveries, on the other hand, decreased by between 0.75 per cent and 2.5 per cent for every 1 per cent decrease in fines content, depending on froth height. This paper explores further insights into iron ore flotation processing at different slimes concentrations.

Aug 24, 2022

By Regis Texeira, Leopoldo Gutierrez, Vicente Hernandez, Caludia Vidal, Lina Uribe

"Molybdenum is currently the most important by-product of Chile´s copper mining industry. This mineral has gained international relevance over the years, because of its price. At mining deposits in Chile, copper and molybdenum are extracted together and then separated in a concentration process consisting of several flotation steps using sodium hydrosulfide (NaHS) as copper depressant. However, there are environmental issues related to the potential emisions of toxic hydrosulfide gas and bad odours, which affects nearby communities and suppose a risk for operators. This problem has led to the need for development of new technologies to eliminate the use of NaHS in the process of selective flotation of Cu and Mo minerals. In this work, results of flotation tests in which lignin derivatives reagents are used to obtain the selective separation of Cu and Mo minerals by flotation are presented. In this technology molybdenite is depressed by the action of lignin derivatives (lignosulfonates), while copper sulfides remain hydrophobic and float. The use of lignin derivatives in the selective flotation of copper molybdenum minerals represents a non-toxic alternative to NaHS.INTRODUCTIONSeparation of copper sulfides from molybdenite is commonly achieved through a two-stage flotation process. In the first stage the collective flotation of copper sulfides and molybdenite is promoted to generate a collective concentrate which is then treated in a second stage with sodium hydrosulfide (2.5-3.0 kg/t NaSH) to depress copper sulfides flotation without affecting the flotation of molybdenite. As a result a copper concentrate with 30-35% Cu, and a molybdenum concentrate with 50-52% Mo are generated. Although this process is widely used at industrial level, environmental issues related to the risk of H2S generation and bad odors have always been a concern. Thus there is a need in the industry for a more environmentally friendly process to separate copper sulfides and molybdenite."

Jan 1, 2018

By Jim Bruce, Peggy Hagerty Duffy, Mary Ellen Large, Allen Cadden

"Over the past 40 years, Deep Foundations Institute (DFI) has executed its mission “to bring together multi-disciplined individuals and organizations to find common ground and create a shared vision and consensus voice for continual advancement in the deep foundations industry”. Like DFI, micropile technology began a significant growth path in the mid-1980s. This paper highlights how DFI’s mission was executed in the deployment and expansion of micropile technology.INTRODUCTIONMicropiles are small diameter foundation elements constructed using specialty drilling and grouting methods. Micropiles have evolved since their introduction into the North American market in the 1970s from being lightly loaded (less than 30 kips) elements used primarily for remedial applications, to today’s high-capacity, often hybridized foundation systems, for both remedial and new-build projects. Micropiles now occupy a substantial market segment in North America.For 40 years, DFI has aimed to be the forum for discussion of all issues related to deep foundations design and construction. DFI now supports 21 technical committees and working groups on all deep foundations technologies and has expanded to include regional chapters in Europe, India and the Middle East.Several key steps are required for the successful execution of DFI’s mission, including identifying a need, engaging dedicated and knowledgeable people, developing effective vehicles and resources for information sharing, cultivating stakeholder contributions and advancements, stimulating influence/impact on deep foundations market, and expanding approaches to continue progress. Pile drivers in New York City (the original organizers of DFI) positively affected their market using these same steps: they recognized a specific need, gathered the people who could affect change, convened a discussion forum (which is common today, but was innovative at the time), defined tasks to address the issues, and influenced their market by improving means, methods and owner perception of their services. These forward thinking, proactive members created a mechanism for communication among all related parties that would advance the profession by improving safety, quality and value of pile driving construction.Micropile technology has evolved in the United States and around the world for the past four decades. The accumulated efforts of DFI and other, similar organizations such as The International Association of Foundation Drilling (ADSC) have contributed to this evolution. The advancement of the micropile industry – and consequently the micropile market – has been intimately tied to the execution of the mission of DFI."

Jan 1, 2017

By Christopher J. Brown

"Proper ground stability in gate roads has been a critical aspect of success in longwall mining. In particular, the tailgate has proven to be one of the more active mine areas that needs to be managed (Barczak, Dolinar, and Mucho, 1999). As longwall tailgate support technologies continue to be developed and improved, Strata Worldwide has worked to design and manufacture a revised Propsetter to provide additional support capacity and enable applications at greater mine heights. The support is targeted for tailgate applications; however, it can also be used for roof support in various types of mining environments. This paper describes the design changes for enhancing the support capacity of the Propsetter to more closely align its performance with other support technologies currently being employed in longwall tailgates. Balancing changes to each design aspect of the Propsetter was key to successfully improving the roof support load capacity while maintaining controlled deformation. Increasing the load capacity would allow a mine to improve support efficiency with a smaller, less intrusive support compared to support alternatives and to reduce the cost per foot of supported entry. The target support capacity was 80 to 100 tons at two inches of deformation to more closely match the performance of competing tailgate supports, such as the 24-inch-diameter CAN®. To achieve this goal, changes were made to all design aspects of the Propsetter: diameter, wedge cut depth and angle, pod size, and confinement rings. Test results from the NIOSH Mine Roof Simulator verified that these design changes were successful in increasing the capacity of the Propsetter to the 80- to 100-ton range at two inches of deformation. INTRODUCTION Roof support is one of the most fundamental elements of the underground mining process. As materials are removed from the earth, geological conditions will almost always require some form of roof support to keep the extraction area open and stable. Coal mining environments often experience difficult geological conditions that require both primary and secondary forms of roof support to keep the mining environment safe and economical. The secondary support system serves as additional support in the case the primary support system is inadequate. If designed properly, the secondary support system will also assist in maintaining integrity of the immediate roof beam (Barczak, 2000)."

Jan 1, 2017

By J. Cayouette, C. Bolduc, P. Blatter

"The LaRonde mill was commissioned in 1988 and began treating ore from the Penna shaft in 2000. The mill has been expanded to accommodate 7,500 t/day, but ramped down to 6,000 t/day since the deep extension began. The process recovers gold, silver, and base metals. In 2008, the Goldex plant began trucking gold-pyrite concentrate to a treatment plant feeding pulp to the LaRonde mill, increasing gold output by 40,000 oz. In 2009, the high-grade Lapa ore processing facilities were annexed to the LaRonde plant, increasing gold output by 120,000 oz. This paper outlines the metallurgical considerations related to the treatment of different ore types.RÉSUMÉ Le concentrateur de la mine LaRonde a été mis en service en 1988 et a commencé à traiter le minerai du puits Penna en 2000. La capacité du concentrateur a augmenté afin de permettre le traitement de 7 500 tonnes de minerai par jour, capacité qui est retombée à 6 000 tonnes par jour (tpj) depuis le début de l’extension en profondeur de la mine. Ce procédé permet de récupérer de l’or, de l’argent et des métaux communs. En 2008, l’usine de traitement Goldex a commencé à transporter par camion du concentré de pyrite et d’or vers une usine de traitement alimentant en pulpe le concentrateur de LaRonde, augmentant ainsi la production d’or de 40 000 onces. En 2009, les installations de traitement du minerai à haute teneur de Lapa ont été annexées à l’usine de traitement de LaRonde, augmentant la production d’or de 120 000 onces. Cet article passe en revue les considérations métallurgiques liées au traitement de différents types de minerai.INTRODUCTIONThe LaRonde metallurgical plant in the Abitibi region of Quebec, Canada, evolved into a mature milling site following expansions in 2000–2003, thanks to improved processes, manpower, and water treatment capabilities that better accommodate the complex constituents of the LaRonde ore. The ore requires a sequence of grinding, copper- lead and zinc flotation, and precious metals leaching, ending with a carbon-in-pulp (CIP) gold recovery. A portion (35%) of the tailings is sent back underground as paste backfill after being treated with the SO2-air cyanide destruction process. The tailings area has a dedicated cyanide destruction and metal precipitation area through which the used water passes before returning as recycled water. A biological water treatment plant was built in 2004 to address water toxicity in the final effluent. The water toxicity was the result of the high sulfide content of the LaRonde ore (from thiocyanate or stable cyanide species buildup) and the use of 90% recirculated water in the mill. The water treatment plant uses bacteria to transform thiocyanate into nitrates and precipitate phosphorus from the water before it is discharged into the environment."

Jan 1, 2017

By R. J. Heath

Potassium, together with nitrogen and phosphorous, is one of the essential nutrients required for growth. All living things need potash and so the major demand for potash (approximately 95% of, total demand) is as a fertilizer. Traditional agricultural techniques relied on the return of organic materials to the soil to provide nutrient requirements and maintain soil fertility, and the prevailing low crop yields required little in the way of added fertilizers. But agricultural productivity has increased dramatically in recent times, and this increase in crop yields requires substantial amounts of added nutrients to keep the soil fertile. It follows that there will always be a demand for potash. There is no substitute. Other fertilizers that contain N and P are complementary and not competing products.

Jan 1, 1987

By X. Gu

Mining operations, especially surface coal mines, have great impacts on the local ecosystem and the environment. However, it has been a common practice in mine design that the economic evaluation considers only the operating and capital costs, while the costs incurred due to ecological damage are left out. Such practice underestimates the total cost of mining and ignores the difference in ecological impacts between different mine design alternatives. With growing interest in sustainable development, the mining industry is under increasing pressure to operate not only based on economic and engineering principles but also on principles of sustainability. Therefore, estimating ecological costs of mining and considering such costs in the mine design process is an important step towards reducing ecological impacts at the design stage. The objective of this paper is to quantify the ecological costs of open pit coal mining and to demonstrate the influence of such costs on the ultimate pit design. The ecological costs of mining are estimated based on the areas and types of land damaged by mining activities and the carbon emission from energy consumption. Four major components of ecological cost are identified, namely, lost value of direct eco-services, lost value of indirect eco-services, prevention and restoration costs, and the cost of carbon emission from energy consumption. Necessary equations are given for estimating these costs. An algorithm is described for ultimate pit optimization in coal deposits with near-horizontal coal seams. A case study is presented in which the ultimate pits with and without ecological costs are optimized and compared to show the influence of ecological costs on the pit design outcome.

Aug 1, 2013

By E. Lentilucci, A. Dey, X. Liu, A. Datta, S. Ghosh

The segmentation of quarry blast smoke plumes is a crucial research area that has the potential to enhance safety, environmental monitoring, object detection, and regulatory compliance in the mining industry. Smoke plume segmentation can be used to identify the spatial extent and temporal evolution of smoke plumes generated by the blast. This information can be used to improve the understanding of blast dynamics and optimize blast designs. Furthermore, smoke plume segmentation can assist in identifying potential environmental and health hazards associated with the release of smoke and dust particles into the atmosphere during quarry blasts. However, many current smoke plume segmentation algorithms are designed for segmentation of smoke plumes from fires and are not suitable for segmentation of plumes from quarry blasts. The proposed method in this paper leverages the video frame captured before the blast as a stationary background image, which helps to reduce other confuser objects present in the image along with a selfadaptive clustering method. The color channels of the image are utilized based on the different contrast properties of the smoke, with a self-adaptive gradient compensation applied for edge detection of the smoke plume. This approach offers a novel and effective way to segment smoke in quarry blast analysis, with potential applications in the calculation of noxious gas volume and concentration within the plume. Compared to other algorithms, our method improves accuracy, decreases the false alarm rates, and reduces the overall miss rate. Overall, this paper contributes to the research on smoke plume image segmentation, particularly for quarry blast smoke plumes, which possess unique characteristics that require specialized algorithms for accurate segmentation.

Jan 1, 2024

Mill #4 processes mildly refractory ore from Carlin Trend deposits. Diagnostic analysis of plant operating data was used to generate a mathematical model containing the key parameters influencing the gold recovery. The model was used to direct modifications to plant operating practice. The cyanide dosing strategy was changed to reduce preg-rob gold losses and cut reagent consumption A finer grind was achieved without capital investment. The density in CIL was lowered, and tighter control was exercised over plant throughput. These changes resulted in a recovery increase of at least 2%, worth $111,000/month at $300/oz, and concomitant reagent cost savings of $55,000/month.

Jan 1, 1999

By Thomas Boundy, PATRICK TAYLOR

Indium recovery from liquid crystal display (LCD) waste has been the subject of over 50 peer reviewed publications over the last decade; however, the first commercial recycling facilities are just beginning to be built. The low value of indium in the LCD screen material has posed a major challenge to would-be recyclers. Uncommon material combinations and geometries have further challenged development. A review of published literature regarding extraction of indium from LCDs will be presented and themes of advantageous processes will be highlighted. Barriers to rapid expansion of any recycling technology in the form of manufacturin gpractices, environmental regulations, and geographic constraints will be discussed.

Mar 1, 2018

By R. J. Sawyer

The Greens Creek underground polymetallic mine restarted production in 1996 from a newly discovered high grade ore zone. Efforts to improve payable gold recovery have focused on gravity separation. The paper compares testwork and plant results for a newly installed gravity circuit.

Jan 1, 1997

By V. A. Masloboev, A. V. Svetlov, D. V. Makarov

"The methods of heap leaching are considered to be the most promising for the low-grade copper-nickel raw materials. The article presents intensification capabilities of the process. Objects of research: the low-grade copper-nickel ores of Moncheplutone deposits (Moroshkovoye Lake, Nyud Terrasa, Nittis-Kumuzh’ya-Travyanaya (NKT), as well as the copper-nickel ore dressing tailings of the “Kola MMC” JSC. The following directions for the intensification of the low-grade copper-nickel raw materials heap leaching have been considered: preliminary electric pulse destruction (EPD) of ore; ore crushing and further sulfuric acid agglomeration. The impact of sulfuric acid concentration (1-3%) on the extraction of non-ferrous metals kinetics from the copper-nickel ore dressing tailings under various conditions of the percolation leaching has been studied. INTRODUCTION The low-grade grade sulfide ores at the abandoned and producing deposits, overburden rocks, mill tailings and non-ferrous slag are thought to be one of the large-scale sources for non-ferrous metals, on the one hand. On the other hand, they are known to be the subjects of emergency environmental danger. For this reason, the use of mine dumps and tailings, as well as the remained ores left in the ground as raw products, and at the same time decreasing the load on environment, are considered to be the pressing ecological and economic issue (Chanturia et al., 2012). Methods of heap hydrometallurgical and bacterial leaching are sure to be potentially productive for processing such low-grade and technogenic raw materials (Petersen, 2016). The early studies of hydrometallurgical method possibility to process copper-nickel ores of the Murmansk region deposits were launched in the seventies of the previous century (Golovko et al., 1978). For referencing purposes, the main types of impregnated ores from the deposits Zhdanovskoye, Kaula, Sopchinsky Plast and Lovnoozerskoye were selected. The metal content varied, as %: 0.46-1.49 of nickel, 0.01-0.62 of copper. In the first experiments, the solution containing 150g/l of H2SO4 and 135g/l of NaCl, was used in the capacity of leaching reagent. The possibility of underground metals leaching from the ores of the Lovnoozerskoye deposit was justified due to the performed laboratory and further large-sized tests."

Jan 1, 2018

By Wayne A. Greenwalt

A method that determines venture participation when the decision maker's level of risk aversion varies according to venture profitability and risk investment is presented. The decision maker's fundamental aversion to risk is established by the selection of a desired working interest for a venture that anticipates only a discounted payout.

Jan 1, 1982

By Glenville A. Collins

IN 1932, Horace Onyett at Oroville, California, built a practical floating washing plant along the general lines as now known, using a 24 in. by 12 ft. trammel; it was fed with a ½ yard dragline bucket, rated then at 200 yards per day. Onyett dubbed his plant a 'Doodlebug' which name has clung to this type of operation ever since. In general, the 'Doodlebug' dredge is the outgrowth of the depression of 1929, wherein many dirt contractors had surplus idle equipment and a few of them ventured to use it for placer mining. Many such plants were impractical and poorly designed and adapted often to locations not suited to the purpose. However out of the general idea came refinements until today dragline dredging has a very definite place in the gold production of the world. Many of the early operators, being mainly contractors without mining experience or technical knowledge of gold saving, geology, or mechanical design, naturally went through stages of trial and error until a workable unit became standard practice. Credit should be given Bodenson Iron Works of San Francisco, who did a notable job of pioneering and building of floating washing plants; also, to Lord and Bishop, contractors of Sacramento, who were among the early operators, and to several others who built and rebuilt their plants until the weak spots were strengthened to take the beating required, and yet deliver a high degree of efficiency.

Jan 1, 1945