Search Documents

By Stephen C. Tadolini, Robert Hawker, Peter Mills, Colin Grubb, Tom Meikle

"In unfavorable strata conditions, it is often necessary to install additional long tendon support as part of a primary support cycle. Although these support systems provide the required additional stability to the roadway installation does have a significant effect on the rate of development. To overcome the slow cure time of Portland cement-type grouts, the use of two component resin systems, such as polyurethanes and urea silicates, have become favorable. However, concerns over low modulus and creep properties has led to the development of a two-component grouting medium that displays the properties of traditional cable grouting materials with the rapid reaction times of pumpable resin systems. This paper describes product testing, application, surface trials, underground trials, and full-scale applications of the Tekthix System in a dynamic underground environment. INTRODUCTION Single-component cement grouts have been used to anchor long tendon supports for many years. They range from high- to low-slump Portland cement and can be slow-setting to fast-setting grouts. However, current cement grouting systems, which includes the grout and equipment, have some disadvantages: 1. Low-slump grouts require pumps that can handle a thick, high-viscosity grout, so choice of pumps is limited. 2. Pumping distance is limited with current cable bolt grout pumps; operators often tend to add water to allow pumping long distance, which adversely impacts the quality and strength of the material. 3. Fast-setting grouts tend to cause issues with pump and line blockages due to the reduced working life of these single-component materials."

Jan 1, 2017

By R. L. Loofbourow

SEVERAL categories of storage are used depending on capacity. Operational storage, which is small in comparison with the market, facilitates handling surges of a few hours' or a few days' duration. Seasonal storage, usually larger, permits accumulation of product during sea- sons when demand is low, for delivery when demand is high. In producing areas, large storage may permit production at a uniform rate, without waste or distress sale. Near large markets such storage increases the efficiency of transportation, allows a more extensive or higher grade market to be served, and affords protection against interruption in delivery.

Jan 1, 1959

By Clinton A. Hollingsworth

The Flotaire Flotation Cell is a simple, efficient hydraulic/pneumatic Flotation Cell that has no moving parts. It is normally used in conjunction with a surfactant (frother) in which case the combination is known as "The Flotaire System". On many ores, metallurgical efficiencies are substantially increased and operating costs reduce. For example, in floating phosphate rock, it is not unusual for BPL recovery to be increased more than 10%, the major increase being due to floating coarse phosphate, up to 14 mesh, and the difficult to float phosphate. Substantial improvements have also been made on coal, mica, vermiculite, kaolin, barite, copper, etc.

Jan 1, 1981

By M. C. Malamphy

A general description of the activities and results of bauxite investi-gation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the sixteenth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project, except the deep holes drilled to test the geophysical anomalies. The locations of the latter holes show on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township is given with the discussion covering that area.

Jan 1, 1948

By Alejandra Díaz Valdiviezo

El presente texto revisa el panorama actual de las rocas y minerales industriales en el Perú a través de los estudios de INGEMMET. Dentro de este estudio, las rocas minerales e industriales son recursos que representan un interesante potencial geológico en la geología peruana, constituyéndose en la principal fuente de materias primas e insumos para el abastecimiento de los principales subsectores económicos. Las rocas y minerales con mayor espectativa de inversión son: las rocas carbonatadas, sílice y arenas silíceas, fosfatos, yeso, rocas ornamentales como travertino, piedra laja, granitos, ente otros. Asímismo, en la actualidad hay varias regiones que no son óptimamente utilizados como las arenas silíceas y calizas en Cajamarca y Amazonas los granitos en Arequipa, travertinos en Puno, entre otros.

Feb 1, 2014

By M. L. Klohn

The Felder ore deposit is a 5,000,000-pound uranium deposit in the South Texas Coastal Plain. It occurs in the basal sand of an Oakville Formation (Miocene) alluvial system. The host sand is a carbonate-rich arkose which contains virtually no carbonaceous debris and has been reduced by the local introduction of hydrogen sulfide. The ore lies well within the reduced zone and occurs as coffinite and uraninite that fill interstices and coat and replace grains. The overall geometric configuration of the ore is that of a winged, crescentic ore roll. Weak mineralization extends the wings of the ore roll and gives greater expression to the roll character. Departures from the shape are controlled by discontinuities in bed- ding and by proximity of the ore to the surface. Associated with the uranium is a broad halo of anomalous molybdenum. Subsidiary mineralized trends suggest a pre-existing up-dip position for the main roll. Oxidation from the surface largely destroyed this previous roll by solubilization of uranium. Uranium subsequently migrated into favorably reduced sand and reprecipitated at the present roll position.

Jan 1, 1970

By M. A. Trevits

The explosion hazard presented by methane gas in coal is confronted daily in the mining industry. Research has developed several viable methods for gas control in addition to conventional dilution by ventilation. Such methods include the drilling of horizontal or cross-measure boreholes from a mine opening and vertical boreholes hydraulically stimulated in advance of mining or for gob gas drainage. The long-term production history of five gas drainage installations was studied. Three installations were completed in the Pittsburgh Coalbed: two in West Virginia and one in Pennsylvania. The remaining installations were completed in the Mary Lee Coalbed in Alabama and the Sunnyside Coalbed in Utah. The types of drainage methods utilized included horizontal and vertical boreholes. The length of production studied ranged from 860 days to 36 years. The cumulative production from the five sites was in excess of 155 Mm3, representing a significant volume of gas.

Jan 1, 1985

By Stephan A. Jefferis, Adrian H. Bath

"This paper draws together some themes on the durability of barrier systems, and particularly cementitious systems. For contaminated land and water retaining structures, durability can be poorly addressed at all stages of a project, from specification, to barrier material selection, barrier design including toe-in and through to performance assessment in operation. Permeability (hydraulic conductivity) is a dynamic property which will vary over time as reaction processes propagate through a barrier. However, laboratory testing, when undertaken, tends to be focused on short term tests with aggressive chemicals so that the effects of longer-term processes such as carbonation and leaching by permeating water are missed. For water retaining structures, carbonation and leaching actually may be the most significant processes affecting barrier performance as the groundwater adjacent to many water bodies can be otherwise rather benign (as regards bentonite and cementitious systems). These and other reaction processes have been modelled in the arena of nuclear waste repositories and procedures are well recognised. However, such procedures have yet to be widely adopted for the assessment of other barrier systems.INTRODUCTIONOver the last few decades there has been an enormous amount of laboratory research on the durability of barrier materials or more specifically papers reporting the results of permeability tests. Unfortunately there is a much smaller literature on scaling test results to barrier dimensions in the field or to required design lives. Although in the geotechnical industry durability research has been largely laboratory based, in the nuclear industry where relevant timescales are multi-millennia rather than decades, research has been heavily underpinned by geochemical modelling. A significant purpose of this paper is to examine the tools that may be used to analyse the results of tests on barrier materials used in geotechnical engineering, for example, for water retaining structures and contaminated land and draw the attention of the construction industry to the potential of the modelling procedures developed for nuclear repository assessments. Modelling can help to identify underlying processes and so augment information from laboratory testing focused on changes of physical properties such as permeability and strength."

Jan 1, 2016

Silver bearing bulk sulfide concentrates from several Peruvian mines were autoclaved in a 19 liter (five gallon) laboratory autoclave in Lima, Peru. Cyanidation of autoclaved concentrates following a hot lime jarosite destruction step extracted over 98 percent of the silver and over 95 percent of the gold. Autoclave operating parameters such as time, temperature, pulp density and autoclaved solids recycle were investigated and reaction rates determined. The problems of excessive heat generation, silver solubility during autoclaving, and formation of pellets containing unreacted sulfides were addressed. The data presented will be used to design a continuous autoclave pilot plant to pro-vide reliable scale up data for a 50 -100 ton per day facility.

Jan 1, 1992

By M. Normandin

The performance of various polymers and other macromolecules used to flocculate red mud particulate materials in the Bayer process can be evaluated on the basis of their efficiency to achieve adequate settling velocity and turbidity level, The Jar Test is widely used in the mineral industry to determine the efficiency of solid-liquid separation processes, particularly for gravity settler of the Bayer process. However, a high level of variability is found in the data obtained by this methodology, In this study, different parameters of the cylinder test procedure are evaluated to determine their role in the overall variability of the method, As demonstrated by laboratory testing, the overall variability can be considerably reduced by good laboratory practices.

Jan 1, 2005

By Atulya Verma, Samantha Espley, Nashel Kalaka

Numerical modelling simulations of proposed mining sequences are used to evaluate mining induced stress concentrations and their migration associated with the progress of mining. This analysis is a standard practice for most prospective mining projects at various levels of feasibility study. The studies are usually initiated at the beginning of the mining cycle, on a global scale, and are maintained and updated throughout the life of mine (LoM) to identify or address local issues and the required remedies as and when needed. Developments in numerical modeling techniques along with advancements in computing technology and data storage/management capacity have given rock engineers access to a huge volume of data that needs to be analyzed and assessed. The most common approach to numerically evaluate stress concentrations and migrations in underground mines is to select the points of interest in a given volume such as the back of an excavation or points within pillars around critical infrastructure, and plot the stresses or a derivative of stresses over time to represent life of mine concentrations and migrations of stresses. The problem with this approach is the sharp gradient of stresses close to excavation boundaries. Slight changes in the location of selected points can change the stress concentration and migration patterns substantially and all generalized statements about LoM risk can be challenged in one way or another. For global stresses, the most common current approach of data analysis is by viewing series of pictures representing stress contours. In this approach, it is easy to overlook some critical detail and/or be masked by personal preferences of contour/picture representation. To overcome the problem of representing and analyzing huge volume of stress simulation data, the authors, through their experience at different mining operations, developed a volume-based technique to reliably evaluate mining-induced stress concentrations and migrations. The volume-based approach is for risk-based assessments of adjacent regions in the rockmass, in and around planned stoping excavations. The volume of interest is the entire ore body that is planned to be mined, but it could be just a part of the ore body depending on the specific use case. The risk identifiers are the induced stresses as compared to the strength of the rockmass. Over the LoM, the risk identifiers are tracked versus the corresponding excavation ratio of the zone. This approach is very effective in identifying the stages of mining that are contributing the most to the mining induced stress risk and the results can be used for proactive planning and mitigations measures such as alternative mining sequences, or stope sizes, or extraction methods. The approach has also been very successful in application at mature mines, particularly in assessing the re-initiation of mining in zone that has been dormant for some time. The volume-based approach allows for an assessment of the current state of the rockmass and the identification of future risks when planning resumption of mining activities.

Jan 1, 2023

By Pancho J. Garza, Keith H. Dahlen, Chris A. Labye

"Design for reconstruction of the East Flagstaff traffic interchange project located in Flagstaff, Arizona posed particular challenges. The proposed design included construction of a nearly 50-foot tall mechanically stabilized earth (MSE) wall given rightof- way constraints and soft subgrade soils. The tight right-of-way, approximately 15 feet in certain locations, adjacent to existing structures limited the number of viable remedial alternatives to provide grade separation at the proposed bridge abutment without significant settlement. Preliminary analyses indicated the existing subgrade soils - consisting primarily of relatively soft silts and clays with decomposed pumice - would settle approximately 12 to 14 inches resulting in unacceptable wall deformation. Stone columns placed via vibratory methods (vibro-replacement) consisting of circular excavations which penetrate to firm bearing soils and which are filled with crushed stone were selected to densify the existing subgrade soils. The implemented mitigation measures helped limit settlement to less than one inch and allow for successful construction of the project. The project history - including site constraints, subsurface conditions, evaluation of remedial alternatives, stone columns methodology, and effectiveness of ground improvements - will be discussed.IntroductionThis paper describes the subsurface investigation performed for the reconstruction of the Business Route 40 (B-40) (Country Club Drive) and United States (US) 89 Traffic Interchange (TI) located within the city limits of Flagstaff, Arizona. This project is currently referred to as the East Flagstaff TI. The Project Site Vicinity Map is shown below.The former B-40/US 89 TI was considered ineffective in handling the current and projected volumes of traffic which transition from northbound (NB) B-40 to US 89 (both directions), as well as from southbound (SB) US 89 to SB B-40. The intent of the project was to reconstruct the TI to better accommodate projected traffic volumes. The project eliminated the existing ramps from both NB B-40 to SB and NB US 89. The new interchange includes a Tee intersection from B-40 to US 89. In order to accommodate this alignment, the profile of US 89 was raised several feet (on nearly the same as existing horizontal alignment) to match the elevated profile of B-40. B-40 was shifted just west of its current alignment to accommodate construction of a new, wider bridge structure which spans over Industrial Drive, the Burlington Northern Santa Fe (BNSF) railway, and old Route 66. South of the new bridge, B-40 transitioned back to the existing alignment just north of the I-40/B-40 TI. Within the project limits, both US 89 and B-40 were widened to three travel lanes in each direction."

Jan 1, 2015

The paper provides an overview of the development and content of APCOM symposia since their inception in 1961. This development is set within the context of the academic environment in which much of the research published at APCOM symposia is conducted. This environment includes rigorous external assessment of research quality at national levels and against international benchmarks, which carries significant consequences for funding and for the continued existence of the academic minerals industry disciplines. Adverse consequences that undermine the academic provision of mining and resource engineering will impact negatively on the minerals industry by reducing the level of research and education resources available to it.The traditional reductionist approach to research is contrasted with the inter-disciplinary approach that is required to address the complex systems problems that the minerals industry will have to address to ensure its technical, economical and environmental sustainability. Such an approach offers a means of raising research profiles, of establishing mutually beneficial academic-industry engagement and provides an opportunity for APCOM to take a lead role in identifying the research and development agenda for the future

Sep 26, 2011

By E. Vahidi

In this study, a hydrometallurgical treatment involving solvent extraction of zinc using D2EHPA (di-2-ethylhexyl phosphoric acid) has been investigated to recover zinc from an industrial zinc leach residue. The residue was leached with sulfuric acid producing leach liquor which was subjected to solvent extraction for enrichment of zinc and removal of impurities. Operating variables for the zinc extraction process, such as pH of the mixed solution (0.5~5.0), concentration of D2EHPA (5%~40%, w/w), temperature (25~60°?C), A/O volumetric phase ratio (1/2~4/1), concentration of tri-butyl phosphate (TBP) as modifier (3%~7%, w/w), concentration of NaR2RSOR4R in aqueous phase (0.05M, 0.1M, 0.2M) were also studied. Practically all zinc was extracted from the aqueous solution at pH 2.5 with 20% w/w D2EHPA in kerosene. At this operating condition, zinc could be extracted at one theoretical stage at A/O phase ratio of 1/1, as calculated by the McCabe-Thiele method.

Jan 1, 2014

By Peter C. Jones

The paper gives a broad view of the maintenance procedures at the Cassiar Asbestos Corporation property. Comparisons are drawn to indicate the changes in facilities and approach that have evolved over the last 25 years while coping with the northern British Columbia climatic conditions. Special emphasis has been placed on the importance of the support groups providing services for both the mine site and the town.

Jan 1, 1978

By T. M. Ruff

The U.S. Bureau of Mines has developed a portable, inexpensive teleoperation system for mobile hard-rock mining equipment. The system was tested on a compact loader-trammer in a simulated stope. The teleoperation system includes radio remote control and computer-assisted navigation. A recent enhancement includes video cameras mounted on the machine to provide visual information to the operator. This system allows the operator to remain in a safe location while operating the machine from a distance, thus increasing both operator safety and mining productivity.

Jan 1, 2010

Abbey, Robert Graham, District Mgr.. The W. W. Sly Mfg. Co., 50 Church St.. New York, N. Y. '21 Abbott, A. N., Mines Supt., Mazapil Copper Co., Ltd Concepcion del Oro, Zac., Mexico. '28 Abbott, Argyle Campbell, Dev. Dept., E. I. du Pont de Nemours & Co., Wilmington, Del. '29 Abbott, Clarence E., V.P., Charge of Raw Materials, Tenn. Coal, Iron & R. R. Co., 1242 Brown-Marx Bldg.. Birmingham, Ala. '04 Abbott, Louis Benjamin, Chief Engr., Elkhorn Div., Consolidation Coal Co., Jenkins, Ky. '16 Abeel, George H., Jr., Cons. Min. Engr Box 427, Santa Monica, Cal. '18 Abel, Albert E., Asst. to Pres., Valley Mould & Iron Corp Hubbard, Ohio. '19 Abel, Raymond L., Asst. Prof., Dept. of Pet. Refin., Univ. of Pittsburgh Pittsburgh. Pa. '28 Abeel, Leo M., Research Engr., Sullivan Concentrator Chapman Camp, B. C., Canada. '31

Jan 1, 1932

By Joseph T. Coe, Alireza Kordjazi, Michael Afanasiev

Cross-hole sonic logging (CSL) is a common quality assurance measure for the evaluation of the structural integrity of drilled shafts. The results of CSL can be supplemented by a set of tomographic images generated by cross-hole tomography (CT). Although the same access tubes, sources and receivers are used in both methods, CT has the advantage of providing a higher quality image of the possible anomalies in drilled shafts. Nevertheless, it has been reported in literature that the CSL and CT miss anomalies with sizes of smaller than 10 percent of the cross sectional area of the drilled shaft. This implies poor resolution despite the high-frequency of the stress waves utilized in these methods. This issue with resolution can be at least partially attributable to the fact that CT relies entirely on the inversion of the first time of arrival and ignores the information embedded in the rest of the recorded traces. This study examines the application of full waveform inversion (FWI) to generate a higher resolution image of the possible defects in drilled shafts from the same data used for cross-hole tomography. FWI is a wave-field method that aims to directly match the recorded traces with traces obtained from a numerical model of the domain. This has the benefit of avoiding the selection of the first time of arrival, along with increasing the resolution of the final image due to extracting more information out of the traces. Through a series of numerical simulations, synthetic traces were generated from a drilled shaft with defects of known mechanical properties, dimensions, and location. These traces were then inverted to evaluate the performance of FWI for structural integrity testing of the drilled shafts. INTRODUCTION The presence of construction defects can compromise the structural integrity of drilled shafts and negatively affect their performance (O’Neil 1991; Sarhan et al. 2002; O’Neil et al. 2003; Poulos 2005). Several non- destructive testing (NDT) methods exist that are currently used for the evaluation of the structural integrity of drilled shafts. Cross-hole sonic logging (CSL), cross-hole sonic tomography (CT), and thermal integrity profiling (TIP) are well-established and documented in the industry and practical manuals (Brown et al. 2010). NDT methods prevent the need for coring and excavation and are relatively fast and cost effective. Successful implementation of these techniques has also been reported in the literature (Branagan et al. 2000; Iskander et al. 2001; Mullin 2010; Johnson 2016).

Jan 1, 2019

By Mathias Jern, Ruilin Yang

A blast vibration model has been developed that simulates effects of almost all blast design parameters on the blast vibration peak particle velocity (PPV) from a production blast with multiple blastholes at a given point of interest in the rock. The velocity of detonation (VoD), initiation points, explosive types (density, VoD, energy), charge decoupling, and decking in each blasthole are simulated along with other blast design parameters. The information from signature hole blast vibration and the blast design are the input to the model. The model can be used to assess blast damage in proximity of blastholes as well as far field vibration PPV.

Jan 1, 2019

By K. E. Tame

An alkaline leaching procedure for recovering uranium from a submarginal 0.1 percent Ug Og calcareous carnotite ore from the Shiprock , N. Mex . , area was investigated . A recovery of 72 percent of the uranium was attained in a preliminary test embodying the commonly accepted practice of ( 1 ) alkaline leaching at 90° C , ( 2 ) multiple stage filtration and washing for recovery of a clear pregnant solution , and ( 3 ) caustic precipitation of uranium as sodium diuranate , with recycle of the barren solution to the leaching and washing circuits . Ion exchange resins were used in a second , less orthodox test that comprised ( 1 ) sodium carbonate leaching of minus 10- mesh ore at 90 ° C to dissolve the uranium , ( 2 ) filtration to recover the leaching reagent for reuse , (3 ) recovery of the uranium- bearing solution in the filter cake as a pregnant slime slurry by repulping of the filter cake followed by a sand- slime separation and countercurrent decantation (CCD ) washing for rejection of the sand fraction , (4 ) recovery of the dissolved uranium from the pregnant slime slurry by resin- in- pulp (RIP ) , ( 5 ) elution of the uranium from the resin with a solution of ammonium chloride acidified with hydrochloric acid , and (6 ) precipitation of the uranium with ammonia gas . About 83 percent of the uranium was extracted from the ore and 95.5 percent of the dissolved uranium recovered by ion exchange . Improved laboratory results were obtained using the RIP process , but larger scale tests would be necessary for economic evaluation of the two processes .

Jan 1, 1964