Search Documents

By B. W. Gandrud, G. T. Bator

The recent introduction of small coal jigs in Alabama to meet the needs of truck - mine operators for cheap and economical cleaning equipment marks another step in Alabama's pioneering record in the mechanical cleaning and preparation of coal . During the past 4 or 5 years a number of these small jigs , with capacity of 5 to 10 tons per hour , have been installed at Alabama truck mines and at a few truck mines in Illinois , Tennessee , and Pennsylvania . Most of the installations have been at mines that specialize in the production of domestic , stoker coal . This report describes three models of small jigs and includes performance data obtained recently on one of the models by the Bureau of Mines, United States Department of the Interior , in cooperation with the University of Alabama, Tuscaloosa , Ala . , for the purpose of comparing it with fullsize jigs on a performance basis . With literally hundreds of truck mines now in operation throughout the country , it has been assumed in preparing this report that there is widespread interest in the availability of small - scale inexpensive preparation equipment for use at such mines in the production of steam and domestic coal and in some instances coal for manufacture of coke . Practically none of the coal from Alabama truck mines is scld to coke - oven plants ; but in some sections of the country truck mines supply a considerable amount of coking coal, and the use of small, inexpensive washers at some of them might be very advantageous during the present war emergency from the standpoint of increasing pig - iron production through improvements in coke quality .

Aug 1, 1943

By Shahriar Vahdani, Andy Herlache, Andrew Bro, Wei-Yu Chen

"The Presidio Parkway Project will reconstruct approximately 1.6 miles of highway, including seven bridges, three cut-and-cover tunnels, and an undercrossing connecting the Golden Gate Bridge to the City of San Francisco, California. The project site is approximately 5.6 miles from the San Andreas Fault, which is capable of producing magnitude 8 earthquakes. Seismic hazards include strong ground shaking, soil liquefaction, ground settlement, and lateral spreading. At the Tennessee Hollow bridge section up to 30 feet of loose sands and soft clays are present. Concerns are raised that standalone drilled piers will experience excessive lateral soil loads from liquefaction-induced lateral spreading pressure resulting in excessive pier head displacement of up to 8 inches. Ground improvement by Cement Deep Soil Mixing (CDSM) is proposed to provide additional foundation stiffness. This paper presents the methodology to: 1) assess the effectiveness of the ground improvement in resisting lateral spreading, and 2) optimize ground improvement design at individual bridge bents based on local site condition. A series of 3-D numerical analyses are conducted and the results show that drilled piers with CDSM ground improvement are capable of withstanding seismic demands from lateral spreading and the lateral pier head displacement is reduced to less than 2 inches. The adopted analytical approach is efficient at modifying design for individual bents and can be considered for future pier foundation design in seismically active areas. IntroductionThe Tennessee Hollow bridge section (Low Viaduct) is an integral component of the Presidio Parkway project which will replace the existing facility with a new multi-lane roadway between the Golden Gate Bridge and the City of San Francisco. As shown on Figure 1, the project site is located about 5.6 miles east of the San Andreas Fault and 12.5 miles west of the Hayward Fault. The Low Viaduct will span over a future wetland habitat subject to tidal fluctuations and potential scouring."

Jan 1, 2014

By M. Seerane, R. Machaka, P. Ndlangamandla

"Metal injection moulding (MIM) is a near-net-shaping powder metallurgy technique suitable for the cost-effective mass production of small and complex components. In this paper, the effects of the metal powder particle size on the final properties of 17-4 PH stainless steel are reported. Three different particle sizes (d50 33.0, 7.91 and 4.04 µm) were used to prepare the injectable MIM feedstocks using a CSIR-developed wax-based binder system at a fixed solids loading of 60 vol.%. The distribution slope parameter and the rheological flow index behaviour were used to predict the flowability of the feedstocks. The effects of the particle size on MIM products were established. The results are discussed in terms of the subsequent microstructural and mechanical properties of MIM 17-4 PH stainless steel against the established MPIF Standard 35. IntroductionMetal injection moulding (MIM) is a near-netshape manufacturing process established as an alternative to produce complex small-tomedium shaped components that were previously fabricated by conventional methods at higher costs (Attia and Alcock, 2011; Todd and Sidambe, 2013).Although recent advances in micromanufacturing (mainly machining and electrodeposition-based) have enabled the fabrication of complex micro-size geometries directly into miniaturized parts, these processes are generally neither routine nor easily accessible at present (Attia and Alcock, 2011).Typically, the MIM process consists of four steps: mixing, injection moulding, debinding and sintering. Mixing involves blending of the desired metal powder composition with carefully selected multicomponent organic binders at the right proportion. This mixture, which is called feedstock, is then injected into a mould of a required shape to form a ‘green part’. Debinding is the removal of the binders by chemical, thermal, or catalytic means while maintaining the shape of the part. Finally, the debound part is sintered to a full or near-full density part (Sotomayor, Varez and Levenfeld, 2010). The MIM process is essentially a combination of plastic injection moulding with conventional powder metallurgy technologies."

Jan 1, 2016

By A Bax, G Wardell-Johnson, W P. Staunton, J McGrath, J J. Eksteen

Since 2001, the AMIRA P420 gold processing technology project series has been studying the recovery of gold using gravity devices, with particular emphasis on the centrifugal units, Knelson and Falcon concentrators. The work has entailed the surveying of operating gravity circuits in Australia, Africa and North and South America.This paper reviews some of the results and lessons of these studies, including common circuit operating and design factors, which limit gravity recovery; pointers towards effective modelling of gravity circuits; and the contribution of gravity to overall gold recovery.CITATION:Wardell-Johnson, G, Bax, A, Staunton, W P, McGrath, J and Eksteen, J J, 2013. A decade of gravity gold recovery, in Proceedings World Gold 2013 , pp 225-232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By O Omidi, P D. Katsabanis

The effect of delay time on fragmentation has been discussed for a long period but rarely in a satisfactory and unbiased way. Despite the efforts of many researchers, delay selection for fragmentation improvement or optimisation remains a controversial issue. Large-scale tests have been plagued with scarcity and scatter of observations, while small-scale tests have been associated with boundary effects and energy losses. Theoretical work is often used to produce explanations for available measurements or tries to simplify wave propagation and wave interaction to guide observation and practical work. The present work analyses results obtained from a relatively large number of small-scale experiments in blocks made of grout, and re-analyses results of previous experiments, to conclude on the effect of delay on fragmentation. It is shown that the main contribution of the delay is found in the fragmentation of the larger fragments of the blast, while the small fractions show almost no effect. Samples, where copper liners were used to inhibit penetration of detonation products in the rock mass, showed effect of delay only when short times were used and steady but poor fragmentation when long delays were used. Based on small-scale experiments, it appears that the fragmentation is optimised when a hole fires prior to the radial cracks, produced by the previous hole, reach the free face of the blast. Gas penetration may result in the development of few more fractures that affect the fragmentation of the largest particles of the blast.CITATION:Katsabanis, P D and Omidi, O, 2015. The effect of delay time on fragmentation distribution through small- and medium-scale testing and analysis, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 715–720 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

The Telfer Underground sublevel cave (SLC) Operation is located approximately 850 m below surface. The cave was designed to propagate through an old decline which was initially used to monitor the cave. There was a requirement to install air blast plugs at two locations in the old decline in order to isolate any potential air-blasts from the active workings in the event of the rock mass collapsing into the cavity. There was a further requirement for an air-blast plug in another section of the mine where there was a risk of the cave intersecting an old workshop and providing an air-blast pathway through an abandoned incline. The design criteria for the plugs was that they should withstand the design air blast loading, be free draining, cost effective and easily constructed with the mining expertise available on site. A plug consisting of grouted mullock was considered robust and least challenging to construct. For the purpose of estimation of maximum air pressure on plugs, it is supposed as a worst case that the rock above a cave falls as an airtight piston onto the top of a muck pile, forcing air into it and also mine workings intersected by the cave. Airflow through the muck pile is governed by Ergun's equation for turbulent flow. In a time-stepping integration scheme, transient air pressures and velocities are calculated according to equations of thermodynamics, in the cave and at intervals along intersected drives by means of a finite difference spatial discretisation. The ability of plugs to withstand computed pressures is assessed by finite element elastoplastic analysis. This paper outlines the rationale for potential air blast loading, calculation of transient air pressures, plug design and analysis of plug behaviour. The plug construction method is also discussed.

Nov 25, 2010

By Brian Rausch

Agenda ?? Refresher: Victor Project Execution ?? Operations Capability roadmap: ? Operations staffing starter group: design participation ? Operations staffing build up for production start-up ? Training and commissioning integration ? Turning OPSCAP ramp-up into a project ?? Go Live! The Results

May 1, 2009

By Nick Hytiris, Mohammed Al Maadheedi, Slobodan B. Mickovski

This paper explores the capacity effects of a square steel plate welded at the ground surface on a driven open-ended steel pile (i.e. the plate would touch the ground surface after the pile achieves the required penetration). A series of strain-controlled, 1-g laboratory tests were undertaken on piles with and without a square steel plate attached. The piles were driven in dry, loosely packed, uniform sand. Two plates were used, one with a breadth equal to two times the diameter of the pile (2D) and the other with a breadth equal to three times the diameter of the piles (3D). A 20% increase in capacity was recorded for the 2D plate, and a 110% increase in capacity was recorded for the 3D plate when compared to the pile without an attached steel plate. The back-analysis of the results allowed the derivation of a new expression to calculate the capacity of bearing plates, which accounted for the effects of sands compaction and dilation. By extrapolating the findings of these tests to a hypothetical scenario, a model design problem was described where the length of a pile can be reduced by 20% to 60% (depending on the load) by using a plate attached to the pile. The results of this study can help designers to minimise penetration depth; thus, achieving a more economical and sustainable design.

By Mohammed Al Maadheedi

This paper explores the capacity effects of a square steel plate welded at the ground surface on a driven open-ended steel pile (i.e. the plate would touch the ground surface after the pile achieves the required penetration). A series of strain-controlled, 1-g laboratory tests were undertaken on piles with and without a square steel plate attached. The piles were driven in dry, loosely packed, uniform sand. Two plates were used, one with a breadth equal to two times the diameter of the pile (2D) and the other with a breadth equal to three times the diameter of the piles (3D). A 20% increase in capacity was recorded for the 2D plate, and a 110% increase in capacity was recorded for the 3D plate when compared to the pile without an attached steel plate. The back-analysis of the results allowed the derivation of a new expression to calculate the capacity of bearing plates, which accounted for the effects of sands compaction and dilation. By extrapolating the findings of these tests to a hypothetical scenario, a model design problem was described where the length of a pile can be reduced by 20% to 60% (depending on the load) by using a plate attached to the pile. The results of this study can help designers to minimise penetration depth; thus, achieving a more economical and sustainable design.

By H. Bouzahzah

The field of quantitative mineralogy has evolved significantly through the development of image analysis techniques and information technology. Quantitative mineralogical characterization can now be routinely conducted for determining ore compositions and understanding the behaviour of minerals within mineral separation processes. The characterization of mine tailings is another important application of quantitative mineralogy. The estimation of acid and neutralization potential as well as the interpretation of kinetic leaching test results are often based on quantitative mineralogical knowledge (mineral abundance, texture, metal distribution amongst minerals, etc.). The objective of this paper is to determine and compare the accuracy of four mineralogical characterization techniques that are often used for environmental sample analysis: (1) X-ray diffraction, (2) normal analysis from chemistry analyses, (3) normal analysis from specific gravity measurements and (4) SEM-EDS image analysis. For this purpose, three artificial samples were assembled by mixing pure minerals in proportions often observed in mineral processing plant tailings. BILMAT, a statistical data reconciliation software, was applied to reconcile the chemical analyses with the results of other mineralogical analysis techniques and to estimate the acid and neutralization potential of actual mine tailings samples. The acid mine drainage was qualified from the acid potential and neutralization potential equilibrium as determined through quantitative mineralogical analysis. The statistically reconciled data made it possible to predict the metal deportment as a function of their bearing minerals and therefore, in the case of neutral contaminated drainage, to assess metal leaching potential.

Jan 1, 2016

By A. Grimod

Rockfall drapery systems are commonly used as a simple, fast and cheap measure against the rock falling trajectories affecting very steep slopes. The system basically consists of a steel mesh, which is held on the top edge with a longitudinal cable fixed by means of a suitable number of anchors. The effect of this kind of intervention is to control the falls of the rocks, which are driven toward the bottom with slow velocity, or are stabilized on place. It can be used on any kind of slope to protect sensitive target in the mining industry, roads and railways, and inhabited areas. The falling blocks, typically smaller than 0.6 - 1.0 m in diameter, pile up into a trench (or into a ?pocket of mesh?) at the bottom. In comparison to other types of rockfall interventions, the simple drapery is cheaper, and its maintenance is easier, but on the other hand it cannot be considered the remedy for shallow instabilities, because it can only mitigate the effect of the falling trajectories. The design of simple draperies requires the analysis of several factors like the slope features (height, gradient, morphology), the geological and dynamic features (nature of the ground or rock, type of instability, erosion problem, blocks size), the environmental condition (presence of vegetation, aesthetical problem), the installation problem (accesses to the slope, safety for the workers, safety for the surrounding areas) and finally the performance required (temporary or permanent intervention, required maintenance, cost). Finally the most problematic design-step is the choice of the suitable mesh, the top longitudinal cable, and the top anchors type. Because of the highly variable nature of rockfall behaviour these structures cannot be standardized, but they have to be analyzed and designed for each case. Maccaferri has developed a new software application (MacRO 2) has a practical tool to define the mesh and the related supporting structure composed by up-slope cable and anchors. The software, based on the approach proposed by Muhunthan B. et al. (2005), allows designers to verify the top longitudinal cable, the anchors, and the mesh drapery, and to plan for maintenance procedures. Even if the method seems quite simple and rough, it is effective and lets the designer correctly foresee the materials and the geometrical features to be used on the interventions. This paper analyses the condition for the simple drapery installation, the main steps for the calculations, and it will present a case study in a U.S. mine. Nevertheless, even if the software allows a quick and simple calculation approach, onsite observations are always recommended in order to achieve a good design, with the ultimate goal of protecting property and human lives.

Aug 1, 2013

By S Jahanshahi

In an earlier LCA study, the authors showed that the electricity consumption of the electric furnaces used in the production of the ferronickel and ferrochrome feedstocks made significant contributions towards the Gross Energy Requirement (GER) of stainless steel production, on a æcradle-to-gateÆ basis. Given the relatively low efficiencies associated with electrical power generation, substantial reductions in the GER for stainless steel production could be anticipated if more direct use of thermal energy was made in the ferronickel and ferrochromium smelting stages.In view of these findings, a follow-up study was undertaken to investigate the likely environmental benefits of using bath smelting processes for the production of ferronickel and ferrochromium compared to the traditional rotary kiln-electric furnace processes, but still utilising the electric furnace process for stainless steel production. The METSIM process simulation software package was used to set up models of the two bath smelting processes and provide process energy requirements that were incorporated into the LCA. The environmental impacts considered in the LCA were greenhouse (Global Warming Potential, GWP) and acid rain gas (Acidification Potential, AP) emissions and solid waste emissions.The results of the study showed that the bath smelting route reduced the GER for ferronickel production by about 37 per cent over the traditional route, which translated to about a 21 per cent reduction in the GER for stainless steel. The corresponding reduction for ferrochromium was about half that for ferronickel, and when combined with the ferronickel result gave a 25 per cent reduction in the GER for stainless steel production. Similar reductions were also observed for the GWP and to a lesser extent the AP for both feedstocks, as all primary energy inputs were essentially fossil fuel based. Substantial reductions in solid waste emissions were also indicated for the direct use of ores in smelting. By utilising bath smelting processes for the production of the ferronickel and ferrochromium feedstocks, stainless steelÆs suitability for meeting many of the goals necessary for sustainable development, already recognised because of its particular properties, would be even further enhanced.

Jan 1, 2004

By P. Guliov

In the first part of this paper the authors present an overview of industrial minerals produced in the Canadian provinces of British Columbia, Alberta and Saskatchewan, and supplied to the Pacific Rim countries. The second part outlines some of the unique opportunities for industrial minerals that exist in the three western Canadian provinces and those minerals we feel have development potential for overseas markets. Because of time constraints, it is not an exhaustive presentation on industrial minerals, but is focused on a few selected minerals that we believe have high potential.

Jan 1, 1990

By A. Treverrow, G. A. Brooks, H. K. Worner

"The work by H.K Worner and co-workers at CRA in the 1960s, and early 1970s, established that molten metals could be refined continuously utilising counter current flow of metal and slag. Womer also demonstrated that counter current refining could produce highly refined metal products. These developments coincided with the advent of high intensity metallurgical reactors in both the ferrous and non-ferrous industries (e.g. BOS, Q-BOP and later Sirosmelt) that utilised high levels of gas injection to produce rapid stirring and very fast reaction. These new generation of high intensity metallurgical reactors allowed high tonnage rates through relatively small volume vessels.Whilst, it is well known that the counter current flow of reacting phases offers the potential of efficient mass transfer and high purity products, the application of counter current reactors to molten metal/slag systems has been criticized on the basis that they suffer from either low intensity or, alternately, from poor refining due to excessive dispersion. These criticisms relate to the balance between intensity and the refining capacity of a reactor. That is, whilst high levels of mixing transversely to the direction of flow promotes high mass transfer, longitudinal mixing (dispersion) is detrimental to refining. Of course, mixing in one direction invariably leads to mixing in other directions, thus creating a playoff between high mass transfer and excessive dispersion.This balance between intensity and refining has been the subject of recent studies overseas, and at"" the University of Wollongong, using cold modelling techniques to evaluate the effect of mixing on dispersion in a counter current refining launder. These studies have shown that for a given geometry and mixing regime, dispersion decreases with increasing flow of liquid phases. This means that whilst high mass transfer cannot be achieved in a refining launder without sacrificing the degree of refinement, there is no impediment to achieving high productivity through such a system, in fact, high through puts may favour good refining. Thus, it may be possible to match a high productivity smelting operation with a equally productive counter current refining stage."

Jan 1, 1996

By S. Mostaghel, Fariba Azgomi, Steven Goodman, M. Oliazadeh

"It is known that copper loss to the slag phase can be in the forms of chemical dissolution and mechanical entrainment. The contribution of each mechanism to the total Cu-loss depends on different parameters and may vary significantly. To reduce emissions to the atmosphere and to shorten the converting cycle, most industrial processes are aiming at production of high matte grades. Increased oxygen-to-sulfur potential, required by these processes, results in a highly oxidized slag, which in turn leads to an increased concentration of the chemically dissolved copper in the slag phase. Hence, slag cleaning processes are becoming increasingly important for economic viability of the smelting operations. Hydrometallurgical, pyrometallurgical, and mineral processing routes have been used for copper recovery from slag. The current article reviews a trade-off study evaluating two of the commonly used methods (namely flotation and electric slag cleaning furnace) by comparing the technical pros and cons, operability/maintenance requirements, and capital/operating costs of the operations.INTRODUCTIONLarge volumes of smelter and converter slags are produced by copper smelters around the world. It is estimated that for production of each ton of metal 2.2 tons of slag is produced (Gorai, Jana, & Premchand, 2003). Considering the current pressure on the mining and metals industry for “zero-waste, sustainable and environmentally friendly” extraction of metals, it is absolutely essential for metal producers to improve their efficiencies in order to remain competitive. To meet these objectives, almost all metal producers, from steelmaking plants, ferroalloys, base and precious metals producers, are trying to reduce their metal losses to the slag phase. In particular, copper producers are aiming to produce higher matte grades in their smelting furnaces to reduce the converting time and improve their overall throughput. Copper smelters need to minimize their copper/precious metal losses to the slag phase before final landfilling/use of slag. The current article, therefore, briefly reviews the copper loss to the slag phase, methods of metal recovery from the slag and then presents a trade-off study conducted for a green field flash smelter of the sulfide concentrates. A comparison was made between two of the major process routes for metal recovery from slag, namely slag cleaning furnace and flotation."

Jan 1, 2016

By F. A. Renninger

The terms environment and environmental control, when used in today's context, generally imply to the average individual, something to do with pollution and pollution control. These latter terms, likewise, impart visions of fouled air and dirty water attributable largely to the industrial segment of American society. We have been conditioned, by various means, over the past ten years to equate environ¬mental control with pollution control. We have been trained to think of industrial environmental control programs as efforts conceived only to comply with one or more of the recently imposed pollution control regulations. Almost automatically we; approach consideration of environmental control with a degree of pessimism that is we assume that pollution prompted the control program. It is the purpose of this discussion to demonstrate that environmental control. at least as it exists and has existed within the crushed stone industry, involves far more than simply control or reduction of air and water pollution. It involves a dedication to the enhancement of each of the several "mini-environments" which together comprise the total world surrounding any given crushed stone operation. Environmental control, exercised properly, is an optimistic, constructive, forward-looking, enhancing type of activity. It is a function which has been, and should continue to be, willingly and expectantly undertaken by informed management personnel. In short, environmental control. is an activity from which both industry and society can and should benefit.

Jan 1, 1972

By Donald L. Colwell

THIS is a metallurgical war. More than ever before, the mechanized forces and the air-borne warfare are deciding campaigns. Both of these are primarily dependent upon metals. There are two ways of increasing the effective supply of these metals when the demand is greater than the total over-all supply. The American custom, when a shortage of anything develops, is to get more. In the case of some nonferrous metals this has been done. For example, our potential peak output of magnesium will be almost one hundred times the prewar production. Output of aluminun has also been tremendously increased, and production of other metals is being stimulated by every possible means. Our enemies, however, have another successful method of increasing the effective supply of a material, and that is, to eliminate entirely all nonessential uses, and also to use, in essential applications, alternate materials wherever possible. Sometimes, ersatz material is inferior to the original, and consequently does not do the job as well. Often, however, it has been found superior, and many substitute items are now being used both by industry and by the military which will continue even when the original material again becomes available.

Jan 1, 1943

By F Cesnik

The past few years has seen a concerted effort to improve the recovery of gold along with its co-product copper from the æhigh-gradeÆ Ridgeway concentrator at Newcrest Mining LtdÆs Cadia Valley Operations. A number of initiatives were identified and implemented, culminating in a sustained improvement in recovery of approximately three to four per cent for both metals. The key projects that contributed to this improvement included the installation of a 355 kW Metso stirred media detritor (SMD) to create a regrind circuit, installation of froth crowders on the scavenger circuit, installation of a Falcon SB2500SE gravity concentrator as part of the regrind circuit to improve gold recovered to bullion on-site and the optimisation of the grinding circuit to reduce the 80 per cent passing size (P80) of the primary grind from 160 to 121 ¦m for the same throughput via process control, cyclone and ball charge optimisation. This paper will focus on the supporting test work, where applicable, that was used as the design basis for the project, but more importantly the plant data before and after the changes to clearly identify the improvements to plant recovery.

Jan 1, 2007

By P. T. Bissert, J. P. Ducarme, J. L. Carr, A. K. Smith

The continuous mining machine is a key piece of equipment used in underground coal mining operations. Over the past several decades these machines have been involved in a number of mine worker fatalities. Proximity detection systems have been developed to avert hazards associated with operating continuous mining machines. Incorporating intelligent design into proximity detection systems allows workers greater freedom to position themselves to see visual cues or avoid other hazards such as haulage equipment or unsupported roof or ribs. However, intelligent systems must be as safe as conventional proximity detection systems. An evaluation of the 39 fatal accidents for which the Mine Safety and Health Administration has published fatality investigation reports was conducted to determine whether the accident may have been prevented by conventional or intelligent proximity. Multiple zone configurations for the intelligent systems were studied to determine how system performance might be affected by the zone configuration. Researchers found that 32 of the 39 fatalities, or 82 percent, may have been prevented by both conventional and intelligent proximity systems. These results indicate that, by properly configuring the zones of an intelligent proximity detection system, equivalent protection to a conventional system is possible.

Jan 1, 2016

By Beatryz C. Mendes, Igor K. R. Andrade, Roseli O. G. Martins, Gustavo H. Nalon, Rita de C. S. S. Alvarenga, Leonardo G. Pedroti, Carol F. R. Santos, Marcelo A. Alves

This work presents an experimental investigation of the influence of concrete blocks and mortar’s compressive strength on the flexural bond strength, normal to the bed joints, of concrete structural masonry. Third-point beam tests were performed on concrete prisms, considering two different kinds of concrete blocks (compressive strength of 5.9 and 8.2 MPa) and six different cement-lime mortar compositions (compressive strength around 30, 70, and 120% of the blocks’ net area compressive strength). Units’ absorption and mortar’s initial flow and water retentivity were not varied, but remained within the suitable range for use in structural masonry. For both types of concrete blocks, it was observed an increase on the prism’s flexural bond strength with the increase of the mortars’ compressive strength. A lower mortar’s water-cement ratio led to higher bond strength. When fixing the ratio between mortar’s and concrete block’s compressive strength, it was noticed that the increase on the blocks’ strength contributed to a slight increase on the masonry’s flexural bond strength, except when using high strength mortar, in which the increase was significantly greater.

Mar 1, 2018