Search Documents

By R. Maurice King

In the operation of today's large scale ore-processing mills, it is extremely important to have some way of making an objective evalu¬ation of the performance of the available flotation reagents. Attempts to do this may often result in inconclusive findings since the magnitude of the difference in the mill results for any two reagents is apt to be quite small compared to the variability introduced by the process and 'the analytical procedures used to measure them. In cases where two reagents give vastly; different mill results, evaluation becomes a simple matter and as such deserves no further attention here. A question of primary concern, however, is how a mill can go about evaluating the performance of two reagents which may, for example, give a difference of only 0.001% copper in the-tailings or of 0.2% in copper recovery. The casual observer may feel that such small differences may be of little importance, but in a mill-whose daily tonnage is between 30 and 40 thousand, these differences could mean a substantial savings. Before the presentation of an actual example of a reagent testing scheme designed for just this-purpose, perhaps a few minutes should be devoted to a review of some statistical methodology to be used later in the discussion.

Jan 1, 1964

By A. A. Schweizer

Buckhorn ore is hydrous, argillized basaltic andesite, and is at least 60% clay composed of kaolinite and subordinate montmorillonite. Moisture content runs from 10% to 25%. The original crushing plant was a typical compression type, employing a jaw crusher, and two cone crushers. The system was plagued with constant plugging and unable to meet production plans. The three compression crushers were replaced with a Stamler Feeder Breaker followed by a Hazemag Impactor. Production plans are now exceeded. Agglomeration has progressed from an agglomeration drum to cascading conveyors, to introduction of the lime and cement into the primary crusher.

Jan 1, 1987

By Tom Lewis

The metal finishing and electronic industries are searching for ways to recycle materials · and reduce costs. The areas of heavy metal waste and water recycling has gained new interests with the potential of impacting the operation's bottom line. Lewis Environmental Services, Inc. has completed numerous heavy metal recovery and effluent recycling projects with its ENVIRO-CLEAN PROCESS for government and private sector clients. This patented process utilizes a proprietary chemically treated granular activated carbon with enhanced heavy metal adsorption capabilities combined with electrolytic metal recovery to produce a saleable metallic product. The process generates no sludge or hazardous waste and the effluent meets EPA .limits. This paper covers several heavy metal removal projects, two fullcscale commercial installations, and one treatability case study.

Jan 1, 2000

By P. L. Sibrell

Previous research by the U.S. Bureau of Mines has shown that autoclave cyanide leaching of used automobile exhaust catalysts for recovery of platinum-group metals (PGM) is technically feasible. The purpose of this work was to investigate the chemistry of the dissolution of PGM in cyanide solutions in more detail. Where possible, samples of pure, elemental PGM powders or foils were used instead of automobile exhaust catalysts, because of their greater purity. Ultraviolet spectra revealed that Pt and Pd were solubilized as the square planar tetracyanometallate (II) complexes, while Rh was solubilized as the octahedral hexacyanorhodate (III) complex. This explained the poor recovery of Rh from solution by carbon adsorption, solvent extraction, and ion exchange observed in earlier research, because of the higher anionic charge and size of the octahedral complex. Leaching rate studies showed that the rate of solubilization was greatest for Pd, followed by Pt and Rh. Although the rate of chemical reaction was the controlling step for the dissolution of elemental Pt and Rh samples, the rate of pore diffusion was rate limiting for PGM in catalyst samples.

Jan 1, 2010

By Alan Rice

Abstract-The mechanism by which stratiform ore deposits of PGE (platinum-group elements) are laid down in ultramafic igneous complexes is not completely clear. Early studies by the author and coworkers on numerical analyses of the convective cooling of low-Rayleigh-number magma chambers examined the effect of suspended crystal load on fluid density, and raised the possibility that the growth of the suspended crystal load during cooling could split a magma chamber into several convecting layers. The lower layers would have a higher content of refractory phases than the upper layers, which would consist of more evolved melt. This paper considers numerical modelling, as well as theoretical and experimental work in other fields dealing with suspended loads in fluids. The calculations, which are based on the physics of convecting magmas, yield quantitative relationships consistent with the observation that economically interesting stratiform PGE deposits are restricted to large magma bodies, and also yield estimation of the depth in a magma chamber at which certain grades of mineralization may occur.

Jan 1, 1997

By Alan Rice

The mechanism by which stratiform ore deposits of PGE (platinum-group elements) are laid down in ultrama?c igneous complexes is not completely clear. Early studies by the author and coworkers on numerical analyses of the convective cooling of low-Rayleigh-number magma chambers examined the effect of suspended crystal load on ?uid density, and raised the possibility that the growth of the suspended crystal load during cooling could split a magma chamber into several convecting layers. The lower layers would have a higher content of refractory phases than the upper layers, which would consist of more evolved melt. This paper considers numerical modelling, as well as theoretical and experimental work in other ?elds dealing with suspended loads in ?uids. The calculations, which are based on the physics of convecting magmas, yield quantitative relationships consistent with the observation that economically interesting stratiform PGE deposits are restricted to large magma bodies, and also yield estimation of the depth in a magma chamber at which certain grades of mineralization may occur.

Jan 1, 1997

By Jr. Koch

In the Hydrogeochemical and Stream Sediment Reconnaissance (HSSR) phase of its National Uranium Resource Evaluation (NURE) pro¬gram, the U.S. Department of Energy (DOE) samples about 1400 sites for stream sediments in each two-degree quadrangle of the National Topographic Nap Series (NTMS) and about 1200 sites for ground or stream water. Through a geological/statistical analysis, we find that NURE data are useful for assessing the uranium resources of the NTMS quadrangles. Our computer-implemented System for Uranium Resource Evaluation (SURE) calculates a score for each NTMS quadrangle based on the HSSR, geologic, and radiometric data; we score the four Colorado quadrangles--Pueblo, Montrose, Durango, and Trinidad--that comprise the study area. We interpret the scores in terms of geology and the known occurrences, which include the Hanson ore deposit with reserves of 30,000,000 lbs. U308 and the Pitch mine with reserves of 1,740,000 lbs. SURE depends in part on distinguishing mineralized or metalliferous granitoids from barren ones through "geochemical signatures."

Jan 1, 1980

By J. Y. Hwang

Alunite has been utilized as raw materials for producing alumina and potassium sulfate fertilizer in Russia for many years. In the United States, this mineral has not been commercially processed though reserves of 5 to 10 billion tons of alunite ore have been estimated. Major constituents of these ores include quartz and alunite. The minerals are finely intergrown and liberation occurs below 10 microns. Adequate separation techniques for such fine particles have not been developed. A new method for the beneficiation of alunite ore is proposed in this study. 'Ibis method utilizes a small amount of fine magnetite upon which the liberated quartz is selectively flocculated. The co-flocculated magnetite and quartz are then separated from the alunite in a high gradient magnetic separator. Clean products, e.g. an alunite concentrate of 90% grade with 80% recovery, has been obtained from an Utah ore. Techniques for the selective co-flocculation of magnetite and quartz, the separation of the carried quartz, and the recovery of magnetite after separation are discussed.

Jan 1, 1985

By P. Zhang, S. Al-Thyabat

"Phosphate rock contains traces of rare earth elements (REEs) and can be a secondary source of these critical materials as large tonnages of phosphate rock are mined annually. Attention has mostly focused on the extraction of REEs from phosphogypsum, which contains more than 70 percent of the REEs reporting to phosphate concentrate, with only limited work conducted on REE extraction from sand tailings and slime even though they account for 16 percent and 15 percent, respectively, of REEs mined with phosphate matrix.In this work, phosphate flotation tailings were upgraded by gravity separation and froth flotation. Gravity separation was conducted using a laboratory shaking table, while flotation was conducted in a Denver D-12 flotation cell. The concentrated tailings were then leached by nitric acid followed by REE extraction with solvent and ion-exchange resin.The sand tailings were assayed as having 2.6 percent phosphate (P2O5 ) and 198.1 µg/g REEs. It was found that the shaking table could produce tailing concentrate assayed as having 8.6 percent P2O5 and 616 µg/g REEs but with only 20 percent REE recovery, while the froth flotation produced froth concentrate assayed as having 8.1 percent P2O5 and 368.2 µg/g REEs with 63.5 percent REE recovery. Leaching the flotation concentrate with 5.2 M (25 percent) nitric acid followed by extraction with solvent and ion-exchange resin yielded precipitates with REE contents of 0.926 and 0.314 percent, respectively, compared with 0.716 and 0.213 percent when table concentrate was used.IntroductionRare earth elements (REEs) consist of a group of 17 elements: the 15 lanthanides along with yttrium (Y) and scandium (Sc). They are rare not because of their scarcity in the Earth’s crust but because they are rarely found in economic and mineable deposits. REEs are called “seeds of technology” because of their importance to some critical technological industries such as renewable energy, hybrid cars, electronics and batteries. On average, an electric car or a hybrid car contains about 10 kg of REEs (Grasso, 2012; Radhika et al., 2011).REEs are usually categorized into light (LREE) and heavy (HREE). LREEs consist of lanthanum (La), cerium (Ce), praseodymium (Pr), neodymium (Nd), promethium (Pr), samarium (Sm), europium (Eu), gadolinium (Gd) and scandium (Sc), while HREEs consist of terbium (Tb), dysprosium (Dy), holmium (Ho), erbium (Er), thulium (Tm), ytterbium (Yb), lutetium (Lu) and yttrium (Y). About 200 minerals contain traces of REEs, but only three are considered economically significant: bastnasite, with the formula La,Ce(CO3)F; monazite, with the formula(Ce,La,Nd,Th)PO4; and xenotime, with the formulaYPO4 (Jordens, Cheng and Waters, 2013)."

Jan 1, 2016

By Dennis R. Dolinar

Physical property tests were conducted on drill core from three exploratory holes on the Naval Oil Shale Reserve near Anvil Points, Colo. Data and regression analysis curves are presented. Data obtained above the Mahogany zone were used to estimate the potential zone of surface effects from under-ground mining. Single specimen testing was primarily used to obtain Mohr's envelope and subsequent rock properties. The technique is shown to provide satisfactory results for this rock type with a significant reduction of core preparation and testing time.

Jan 1, 1981

By Francis F. Lucas

Jan 1, 1931

By Gabriela Pereira de Miranda

Este estudo teve por objetivo avaliar a soldabilidade a pontos entre os aços 22MnB5 e Dual Phase da classe de 800 MPa de limite de resistência (DP800), ambos com 1,8 mm de espessura. A intenção foi determinar os parâmetros adequados de soldagem para esse tipo de junta soldada, que vem sendo progressivamente utilizada na estrutura de veículos automotores, em virtude do uso crescente de peças fabricadas a partir do aço 22MnB5, submetido ao processo de estampagem a quente (hot stamping). Foram avaliadas as propriedades mecânicas através de ensaios estáticos de cisalhamento e de tração cruzada, em juntas soldadas produzidas a partir da variação do tempo de soldagem e da força aplicada pelos eletrodos. Percebeu-se que as juntas confeccionadas com o tempo de soldagem com múltiplos pulsos (9/2/9/2/9 ciclos) e a força de 5,0 kN obtiveram os melhores resultados em cisalhamento. Em contrapartida, os corpos de prova produzidos com a força de 6,5 kN atingiram os maiores valores em tração cruzada. Independentemente dos parâmetros aplicados, todas as condições avaliadas permitiram alcançar o valor mínimo de carga de ruptura necessária para garantir a qualidade de uma junta soldada a ponto entre os aços avaliados.

Aug 16, 2017

By Gilvandro Bueno

Atualmente, diferentes tipos de vedações laterais de rolos, usados para limitar o efeito de borda em prensas de rolos “High Pressure Grinding Rolls (HPGR)” se encontram disponíveis. O presente trabalho comparou dois métodos usados na vedação lateral: as placas laterais (cheek plates) e as flanges, essas últimas colocadas em um dos dois rolos, a partir de simulações usando o Método dos Elementos Discretos "Discrete Element Method (DEM)", com acoplamento dinâmico multicorpos (Multibody dynamics ou MBD). Como resultado das simulações foram obtidos os perfis de força compressiva ao longo do rolo, assim como a proporção do fluxo mássico de alimentação que é projetado fora da zona de compressão durante a prensagem. As simulações mostraram que ...do HPGR usando o DEM + MBD se apresentam como uma ferramenta muito útil para visualizar o melhor modelo de vedação de modo a minimizar o efeito de borda durante o processo de prensagem.

Oct 30, 2017

By Robert E. Dye

This paper describing the mining methods employed and setting forth prevailing, costs at the property, is one of a series being prepared by the United States Bureau of Mines dealing with properties in various mining districts of the United States and Canada. The Vipond mine is a gold property located at Timmins, Ontario, Canada, and operated by the Vipond Consolidated Mines (Ltd.). For the past fiscal year (ended July 31. 1930) ore was mined and milled at the rate of 310 tons per day, and the value of the bullion produced was $896,397.61.

Jan 1, 1931

By Robert H. Schutz

This publication lists and describes devices approved jointly by the Secretary of Interior and the Secretary of Health, Education, and Welfare, under the provisions of [§]70.300-1, Part 70, Subchapter 0 of Chapter I, Title 30, Code of Federal Regulations (35 F.R. 5548, April 3, 1970), for use as respiratory protection against respirable pneumoconiosis-producing dusts. Included are type C supplied-air respirators approved under Bureau of Mines Schedule 19R and dust, fume, and mist respirators approved under Bureau of Mines Schedule 21B.

Jan 1, 1971

By R. P. Hackl, P. G. West-Sells

Carbonaceous gold ores are particularly attractive for leaching by ammonium thiosulfate as the gold thiosulfate complex is not significantly adsorbed by the organic carbon present in the ore. A technically and economically feasible process for treating these ores with ammonium thiosulfate has been developed. In this process, gold is extracted by leaching the ore with ammonium thiosulfate, the solution is separated from the ore by counter - current decantation, the gold is recovered by precipitation with ammonium sulfide, and finally the gold containing product is upgraded by reacting the elemental sulfur present in the precipitate with ammonium sulfite. The precipitation filtrate is recycled back to the grinding step to close the solution balance. Reagent consumption is not excessive. Besides precipitating gold, the precipitation step removes most deleterious solution impurities and converts a portion of the polythionates back to thiosulfate. This paper discusses the optimization of the leaching, precipitation, and upgrading steps. The results of a 10 kg/h pilot plant campaign are also discussed.

Jan 1, 2005

By Larissa Rodrigues de Carvalho Rocha, Mauro Vivaldino Fernandes, José Eduardo da Silva Moreli, Beatriz Fausta Gandra, Adriano Cesar Carvalhido

No atual cenário siderúrgico, o prolongamento da campanha de um alto-forno tem sido prática usual em diversas empresas. Nesse contexto, a Usiminas tem realizado diversas ações de preservação dos altos-fornos, conciliando com a manutenção da competitividade. Particularmente, o Alto-Forno 3 da Usina de Ipatinga passou por duas trocas de staves, em 2015 e 2018, totalizando a substituição de 68 peças. No presente trabalho é apresentado o planejamento e a execução do retorno operacional após a 2ª troca de staves, destacando as contingências adotadas e lições aprendidas face às ocorrências que impactaram o cumprimento do cronograma previsto. Essa intervenção possibilitará a postergação da reforma para 2021, em alinhamento com as diretrizes da empresa e garantindo uma estabilidade operacional, fundamental para os cumprimentos e superação das metas.

Oct 1, 2019

By Robert A. Laurence

Ore deposits in the Southern Appalachians are ( 1) sedimentary or syngenetic, ( 2) epigenetic, and ( 3) residual. In general, deposits characteristic of high temperature and pressure are found in the Blue Ridge and Piedmont provinces and those of low and intermediate temperature and pressure, including the sedimentary ores, are found in the Valley and Ridge and Appalachian Plateaus provinces. Residual deposits are present throughout the area. Recognition of several periods of intrusion and metamorphism in the Appalachians has changed former concepts which held that most mineralization was of late Paleozoic age in a zonal pattern including all four provinces. Many deposits probably are of early or midPaleozoic age. Similarly, recent studies in geomorphology indicate that the formation of residual deposits is a continuous process and not related to specific cycles of peneplanation.

Jan 1, 1968

By Ricardo Tadeu Meneses Sodré

Principalmente após a crise mundial de 2008, as grandes empresas brasileiras focaram na redução de custo como fator de sobrevivência, buscando manter, em contrapartida a produtividade e qualidade dos produtos. As normas brasileiras ABNT NBR ISO 55000/1/2, combinam atividades sistemáticas, coordenadas e práticas pelas quais uma organização gerencia de forma organizada e sustentável seus ativos tangíveis e intangíveis e sistemas, seu desempenho, bem como seus riscos e custos associados. A norma trata do ciclo completo do ativo, desde a concepção até o seu descarte. A implantação de uma norma deste porte requer compromisso de toda organização, principalmente da alta direção, no intuito de correlacionar os objetivos do negócio com as atividades de manutenção. O ponto principal é entender que a Manutenção é parte de um ciclo mais amplo que trata de todo o ciclo de vida do ativo, logo a Manutenção está contida dentro da Gestão de Ativos. O trabalho visa mostrar de maneira prática como a ArcelorMittal Tubarão está se estruturando para uma implantação futura da ABNT NBR ISO 5500X. Tal estruturação engloba atividades estratégicas, táticas e operacionais de alto nível visando à elevação da maturidade em Gestão de Ativos.

Aug 7, 2018

By Z. R. Llanos

The petroleum refining industry makes extensive use of catalysts for the conversion of crude oils into more usable products such as gasoline, fuel oil and gas, aromatics, and others. Catalysts used for hydraprocessing contain cobalt-molybdenum or nickel -molybdenum, although there are catalysts that also contain tungsten. During hydroprocessing, nickel and vanadium are deposited on the catalysts, eventually rendering them inactive. The refiners are then confronted with the problem of disposing the spent catalysts. In the past, landfilling was a common method of disposal and it is still practiced in some countries. Other refiners prefer to stockpile the spent catalysts at the refineries until the price of metals warrants their sale to metal reclaimers. This practice, however, poses environmental problems to the refineries for storage and disposal of spent catalysts. Other types of catalysts are amenable to regeneration. The purpose of this paper is to focus attention on the recovery of nickel, cobalt, molybdenum, vanadium, and alumina from spent hydroprocessing catalysts by Gulf Chemical and Metallurgical Corporation and to review the use of sodium hydroxide and sodium carbonate for pressure leaching of spent catalysts.

Jan 1, 1986