Search Documents

By R. S. Shoemaker, F. W. McQuiston

The principle of cyanide recovery or regeneration of cyanide from solution, be it a weak wash or a foul solution, is by acidulation. All or part of the cyanogen is converted thereby into hydrogen cyanide which is fixed by an alkali (generally lime) and returned to the cyaniding system (the Mills- Crowe process). The solution is made acid by bringing it into contact with sulfur dioxide. The acidified solution is stripped in a packed tower by a counter flow stream of air in which the air and the solution are brought into intimate contact. The air leaving the tank charged with hydrogen cyanide is then passed to another tank in which it is mixed with an alkaline solution, the latter absorbing the HCN and leaving the accompanying air clean for reuse in removing more HCN from the acidified solutions. Of the recoverable cyanide, 9770 is usually recovered in a three-unit disperser tower system. When there is a considerable content of copper, the solution is made acid following standard procedure; however, the HCN is not removed until the copper is reduced by regeneration. Copper removal at this point may be as high as 90%. After reduction of the copper, the acidified solution then is contacted with a lime solution which brings down calcium sulfate as a second step. The silver, gold, and copper are recovered in the form of a precipitate which can be shipped to a smelter. At the Hudson Bay Mining and Smelting Company, Ltd., most of the precious metals have been recovered in the copper and lead concentrates, but it has been found profitable to submit the flotation tailings to a scavenger cyanide treatment for the recovery of exposed gold contained in pyrite rejected during flotation. Due to the fine particle size, maximum dissolution is achieved in a four-hour contact period. In the cyanidation plant, the thickened flotation tailing at 70% solids is given a four-hour agitation in weak calcium cyanide solution and filtered. Filter cake is repulped and discharged either to the tailing storage area or to the mine as backfill. Clarification, de-aeration and precipitation of pregnant solutions are carried out in a standard Merrill-Crowe unit. Typical analysis of precipitate is as follows: Au, 0.47%, Ag, 4. 88%; Cu, 46.0%; Zn, 13. 8%. Cyanicides in the form of copper minerals limit the reuse of barren solution. To recover the substantial quantities of cyanogen chemically combined with base metals in this solution, a cyanide regeneration plant is in operation. The barren solution is acidified with sulfuric acid in a spray tower where an upward current of air from a blower sweeps the liberated hydrocyanic acid gas to an adsorption unit where it meets a fine rain of lime suspended in plant solution with which it combines to form calcium cyanide. The lime--water solution carrying calcium cyanide is reused in the cyanide circuit. The return gases are drawn into the blower and back to the disperser tower thus

Jan 1, 1975

By J. O. Mack, J. B. Russell

IN recent years, solders containing 20 per cent tin with no bismuth or cadmium have been developed by a few companies, and personnel have been properly instructed in their use. In addition, since the tin shortage, a number of solders containing less than 10 per cent Sn, and some with no tin, are being used in special applications; however, a solder of this type has yet to be developed that is satisfactory for general use. [ ] The purpose of this investigation was to develop an alloy containing a maximum of 15 per cent tin, with no cadmium or bismuth, having solder properties equivalent to or better than those of substitute solders now specified containing i8 to 20 per cent tin (Table I), or even approaching the properties of the standard 40 to 60 tin-lead solder. The wartime restriction of bismuth and cadmium, elements that have beneficial effects on fluidity, solidification range and strength, makes it increasingly difficult to develop a general-purpose solder containing a maximum of 15 per cent tin. In the course of this investigation, 11 elements were used in various combinations with the basic 15-85 tin-lead alloy. These elements were antimony, silver, copper, indium, thallium, lithium, calcium, barium, potassium, sodium and arsenic. In all, 116 low-tin solders were investigated, with the idea of developing a solder that will give satisfactory working properties, specifically in regard to "wetting" of copper, brass and iron, solidification range, capillarity and shear strength of a soldered joint. The relative importance of these various properties plays an important role in the search for substitute solders, since it is almost impossible to retain all of the desired qualities of a high-tin solder and still make drastic changes in the alloy composition. Because of the expected uses of a general-purpose solder, it is necessary that it have properties, especially in regard to wettability, that will enable it to be used on the metals in common use. BASIC CONSIDERATIONS The maximum liquidus temperature of a solder is determined by the particular application involved and the temperature that can be obtained by the source of heat.

Jan 1, 1944

By W. A. Boyer

Edward Thomas (U.S. Bureau of Mines, Washington, D. C.)—This excellent article on an ingenious and successful installation of wooden rock bolts loses much of its effectiveness through an attempt by the authors to establish the general adaptability of this type of support. Possibly because they have only local experience as a guide, they imply erroneously in the first paragraph that the Bureau of Mines has been opposed to wooden bolting, although later in the article reference is made to a Bureau publication on the subject. In 1947 the Bureau of Mines decided to sponsor experiments in roof bolting in coal mines because the experience of the St. Joseph Lead Co. had indicated that this type of roof support appeared to be a roof-fall accident-prevention measure that might be adopted and also effect economies in operating cost. Justification for this belief has been borne out, particularly in coal mining. This program has been carried out under the following general program: 1—The Roof Control Section of the Bureau of Mines has advocated and initiated underground experiments under controlled conditions with many different ideas related to rock bolting since 1947. In no instance has cooperation in developing an idea been refused, no matter how ridiculous it may have seemed at first glance, if it has been requested by a mining company. 2—The Bureau of Mines has no police powers over the selection of roof-support devices and seeks none. 3—At the request of an operator, the Bureau of Mines will make comparative tests on various types of bolts underground and will submit resultant data for the operator's consideration. 4—Wherever possible, the Bureau publicizes successful installations, so that others may benefit from this experience; however, it is careful not to discriminate between manufacturers of bolts or bolt-installation equipment. Unsuccessful experiments probably should also be publicized, but from a practical standpoint it is usually not feasible. In other words, the role of the Roof Control Section of the Bureau is in line with the original purpose for which the Bureau was first organized: to serve industry through gathering, analyzing, and disseminating factual data. It would seem to be logical that the starting point for any experimentation on roof bolts in coal mines should be the time-proved practice of the

Jan 1, 1955

Acid mine drainage (AMD) forms when sulfide minerals are exposed to oxidizing conditions in coal and metal mining, highway construction, and other large-scale excavations. Iron sulfides common in coal regions are predominately pyrite and marcasite (FeS2), but other metals may be complexed with sulfides forming chalcopyrite (CuFeS2), covellite (CuS), galena (PbS), and sphalerite (ZnS). Pyrite commonly occurs with these other metal sulfides thereby causing AMD where Cu, Pb, and Zn are mined. Upon exposure to water and oxygen, sulfide minerals oxidize to form acidic, sulfate-rich drainage. Metal concentrations in AMD depend on the type and quantity of sulfide minerals present. The drainage quality emanating from underground mines or backfills of surface mines is dependent on the acid-producing (sulfide) and alkaline (carbonate) minerals contained in the disturbed rock. In general, sulfide-rich and carbonate-poor materials produce acidic drainage. In contrast, alkaline-rich materials, even with significant sulfide concentrations, often produce alkaline conditions in water. Approximately 20,000 km of streams and rivers in the United States are degraded by AMD. About 90% of the AMD reaching streams originates in abandoned surface and deep mines. Since no company or individual claims responsibility for reclaiming abandoned mine lands (AML), no treatment of the AMD occurs and continual contamination of surface and groundwater resources results. The oxidation of iron disulfides and the generation of acidity occur through several reactions (Stumm and Morgan, 1970). The chemical equations can be found in Caruccio and Geidel (2000). If any of the processes represented by the equations were slowed or altogether stopped, the generation of AMD would also slow or cease. The equations show that 1000 Mg of rock containing 1% sulfur, all as pyrite, would yield upon complete reaction 31.25 Mg of acidity. Therefore, 31.25 Mg of 100% CaCO3 would be required to neutralize the acidity. The alkaline content of overburden determines whether there is enough neutralization potential (NP) to counteract the acid produced from pyrite oxidation. Of the many types of alkaline compounds present in rocks, only carbonates and clays occur in sufficient quantity to effectively neutalize AMD. A balance between the acid-producing potential and neutralizing capacity of an overburden sample will indicate the ultimate acidity or alkalinity that might be expected in the material upon complete weathering. Accurate prediction and control of AMD before surface mining require an understanding of three important factors: 1) overburden geochemistry, 2) method and precision of overburden handling and placement in the backfill during reclamation, and 3) the postmining hydrology of the site.

Jan 1, 2002

D. EPPELSHEIMER, * Middletown, Ohio.-The housing of employees has so many and so varied aspects that in order to reach even an approximately correct solution it is necessary to have in mind a few fundamental principles; but it is not possible as yet to write these housing principles in the clear and correct form that is possible with many of our natural laws. Manifestly, the problem depends first on the kind of people it is necessary to house. What is suitable for the Southern unattached negro is not suitable for the married skilled American. The influx of colored labor has affected quite a number of what were satisfactorily housed communities. The second important factor is the relative proportion of the number of employees to the total employable population of the community in which the industry is located. The employer of a hundred men in. a large city has little responsibility in the matter of housing his employees. If he employs 75 per cent. of the employable population in a community of 27,000, as is the case of the company with which the writer is connected, it means a large responsibility. In the establishment of an entirely new plant in a more or less isolated place, the responsibility becomes greater. As engineers, we design and write the specifications for the machinery to accomplish a definite purpose, and proceed to house it, provide the necessary buildings with their accessories in the way of cranes, or heating systems, or sprinkling systems, as the case may be. There is no reason why the operating force should not be built up in very much the same way: design the organization, write its specifications so that the employment department can secure the proper men, and then house that organization with just as much thought and care as is given the plant. In the plant, the various machines will work along certain definite lines and accomplish certain results; but even if we start with the proper organization it takes considerable time to get that organization working together. One of the most important elements to this end is the proper housing of the organization. A man usually spends more time at home than at work. Proper surroundings and a comfortable, convenient house of good appearance exercise an influence that cannot be denied, and an employee situated in such surroundings is far more inclined to follow the policies of his employer and take an active part in furthering them

Jan 5, 1919

By Lawrence Veiller, D. Eppelsheimer

D. Eppelsheimer, * Middletown, Ohio.—The housing of employees has so many and so varied aspects that in order to reach even an approximately correct solution it is necessary to have in mind a few fundamental principles; but it is not possible as yet to write these housing principles in the clear and correct form that is possible with many of our natural laws. Manifestly, the problem depends first on the kind of people it is necessary to house. What is suitable for the Southern unattached negro is not suitable for the married skilled American. The influx of colored labor has affected quite a number of what were satisfactorily housed communities. The second important factor is the relative proportion of the number of employees to the total employable population of the community in which the industry is located. The employer of a hundred men in a large city has little responsibility in the matter of housing his employees. If he employs 75 per cent. of the employable population in a community of 27,000, as is the case of the company with which the writer is connected, it means a large responsibility. In the establishment of an entirely new plant in a more or less isolated place, the responsibility becomes greater. As engineers, we design and write the specifications for the machinery to accomplish a definite purpose, and proceed to house it, provide the necessary buildings with their accessories in the way of cranes, or heating systems, or sprinkling systems, as the case may be. There is no reason why the operating force should not be built up in very much the same way: design the organization, write its specifications so that the employment department can secure the proper men, and then house that organization with just as much thought and care as is given the plant. In the plant, the various machines will work along certain definite lines and accomplish certain results; but even if we start with the proper organization it takes considerable time to get that organization working together. One of the most important elements to this end is the proper housing of the organization. A man usually spends more time at home than at work. Proper surroundings and a comfortable, convenient house of good appearance exercise an influence that cannot be denied, and an employee situated in such surroundings is far more inclined to follow the policies of his employer and take an active part in furthering them than one dissatisfied with his home and surroundings, which feeling

Jan 1, 1919

By Julian Kennedy

The different types of blowing-engines in use are so numerous that it would not he practicable to consider them all in this paper. I shall therefore only take up briefly a few well known types. The style of blowing-engine most largely used in this country is the vertical engine with air-cylinder above, cross-head between steam and air-cylinders, and two fly-wheels, each having a wrist-pin in its hub, or in one arm. This kind of engine can be built cheaply, takes up little room and is very accessible. Its disadvantages are that the cross-head is liable to break, and that putting the wrist-pins in the wheels tends to set up vibrations in them. It is likely that on the whole this type of engine will continue to be built quite ex tensively. The same general arrangement has also been used to some extent, but not widely, in horizontal engines. The Bethlehem Iron Company has some very fine blowing-engines of this type, except that they are compound, having the one steam-cylinder replaced by two, side by side. These engines are noticeable not only for the very excellent workmanship on them, but also on account of the weight of the pistons being carried by steam-pressnre applied in chambers in the lower side, the steam being supplied to these chambers through the hollow piston-rods. This arrangement, I believe, has always worked well. Another type of engine which has given good satisfaction is the vertical double-engine, having air-cylinders above, steam-cylinders below them, and cranks at bottom, the engines being coupled to cranks on the ends of the shaft, placed at right angles to each other, the shaft carrying the fly-wheel at its center. Engines of this type, except that they are arranged horizontally, are also used to a con siderable extent. These engines avoid the disadvantage of having wrist-pins in the fly-wheels, and also dispense with the long cross head with its attendant disadvantages. They give a very uniform pressure of blast, and are very convenient for starting. The vertical engines of this type, as compared with the horizontal, take up less

Jan 1, 1894

In 1939 at the annual meeting of the Australasian Association for the Advancement of Science, held at Canberra, a paper was contributed by E. de C: Clarke and H. A. Ellist in which a plea was made for more "facts" concerning metasomatism near ore-bodies in Western Australia. From time to time writers here, and in other parts of the world, have discussed the alterations in wall rocks of various reefs and lodes, but little has yet been attempted in the matter of accumulation of quantitative data, both chemical and mineralogical, and in the correlation and comparative study of this data. Such a detailed comparative study is needed to determine the economic value of a practical application of our accumulated knowledge of the phenomena of metasomatism.When in 1939 the opportunity offered for an examination of the core from 4 bores recently put down by the Big Bell Mines Ltd., to explore the ore-body of the Corinthian G.M. 10 miles N.W. of Southern Cross, Western Australia it was hoped that some small beginnings might be made of an accumulation of comparative and quantitative data regarding the metasomatism of the wall rock immediately adjacent to this ore-body.By the courtesy of the Big Bell Mines Ltd., the core from the 4 bores was delivered to Survey Headquarters, Perth;in the middle of June, 1939 and copies of assay plans of part of the underground workings at Corinthian, and of the results of assays of the bore cores, were also supplied by the management of the above company.It was not, however, until March, 1940, that it was 'found possible to investigate the core. At that time the writer's colleague, Mr. R. S. Matheson, conducted a: megascopic examination of all the bores and selected material from two of these for possible future chemical analyses. Late in 1940 the writer commenced a microscopic petrological examination of this material.AIM OF THE INVESTIGATIONThe object of the petrological part of this investigation was to determine whether from a megascopic and microscopic examination of the core, any evidence could be obtained indicating changes, in mineralogical composition...

Jan 1, 1942

By Butt C. R M

Resurgence in Au exploration during the past decade has been characterised by a considerable emphasis and dependence on geochemical procedures. This has been made possible, firstly, by marked improvements in analytical sensitivity over those previously available and secondly, of particular importance to exploration in Australia, by a better understanding of the distribution of Au in the regolith, which has led to the optimisation of sample media. These developments have given exploration companies the ability to seek and detect subtle and widespread geochemical signatures of concealed Au mineralisation and provided an enhanced capability to interpret the data. As a consequence, several new discoveries have been made, even in areas that have been intensively explored in the past. In the deeply weathered Yilgarn Craton (WA), and in equivalent areas elsewhere in Australia and overseas, Au has accumulated in the upper lateritic gravels and duricrusts of the regolith, probably during humid climatic periods in the Tertiary. The laterites may not only be Au ores in themselves, but research by CSIRO and CRC LEME has shown them to be very important sample media, (eg Anand and Smith, 1992). In many areas, however, the laterite has been eroded and hence is unavailable as a sample medium and chemical modification under more and conditions since the Tertiary has leached Au from the upper saprolite. This has greatly increased the difficulties of exploration, particularly where reliance was placed on sampling between 2 and 15 m of the surface. Further research, however, has demonstrated that, despite this leaching, recent remobilisation of An has caused it to concentrate in a specific soil component, pedogenic carbonate, usually in the top I - 2 m, thereby giving surface expression even to mineralisation that is concealed by over 20 in of leached overburden. Secondary carbonates, commonly referred to as calcrete, may precipitate as calcite and/or dolomite in regoliths where the average annual rainfall is less than about 600 mm. Pedogenic carbonates are those that form in unsaturated (vadose) soil horizons. They are widely distributed in the Gawler and Yilgarn Cratons. In the Yilgarn Craton south of about 30¦S ('the Menzies Line'), they are seemingly more abundant over more basic rocks and towards the south east (Figure 1). In contrast, groundwater calcretes form in saturated (phreatic) environments, typically in the axes of major drainages north of the Menzies Line. These are known to accumulate economically-significant grades of U but not, apparently, An.

Jan 1, 1997

By K. E. Merklin, F. D. DeVaney

In the past most of the research in pelletizing has as its aim the production of a physically strong pellet. Now that this problem is solved, more attention is being paid to uniformity in grade and chemical composition. Consideration has been given in recent years to a study of additives which will make pellets partially or fully fluxed. Blast furnace tests show fluxed pellets to have advantages over both fluxed sinter and acid pellets. Lower slag volumes are used more frequently in the blast furnace and the uniformity of the charge, both physically and chemically, is becoming increasingly important. A considerable improvement can be secured by having all of the flux uniformly distributed through the pellets in a calcined state. A fluxed pellet, therefore, should be a superior product. The use of an ore burden that contains an appropriate quantity of fluxing materials is not new to the blast furnace industry. For years the Minette ores of France and Germany, the Clinton ores of the Birmingham, Ala., areas, as well as others, which are low in iron but contain calcium carbonate in sufficient quantities to give them self-fluxing properties, have proven economical. The adaption of the sintering process to the preparation of ore burdens provided a means for artifically associating the fluxstone with the iron ore prior to charging to the blast furnace. In 1944 Torpl discussed the effects of using lime in sinter made in Sweden on the sinter's metallurgical performance in a blast furnace. Hessle2 reported in 1945 on the advantages of using lime in sinter to increase the sintering plants' capacity and reduce fuel requirements. Robinson3 discussed the use of lime in Swedish sintering practice at the 1950 Blast Furnace, Coke Oven, and Raw Materials meeting. One of the suggested advantages was the combining of lime with silica to prevent the formation of a fayalite slag, which is difficult to reduce in the blast furnace. Nilson4 at the same meeting commented briefly on experimental work that had just started in the U. S. on the use of lime in sinter. The literature tends to indicate that most of this early work was directed towards improvement in sinter physical quality, and the fact that the feed to the blast furnace was partially fluxed was incidental. It was not long, however, before blast furnace advantages were being claimed. The matter was forcibly called to the attention of North American operators by reports of remarkable production records established by the Russians using fluxed sinter. The leading step was taken on this continent by the Steel Company of Canada in 1957; McMahon5 reported on the marked improvement in performance of an 18-ft blast furnace using fluxed sinter at its Hamilton works. Other North American operators quickly followed theStelco lead.

Jan 1, 1963

By R. L. Brown

The Buchans mining district is located roughly at the center of the island of Newfoundland and contains some 18 separate mineral deposits. The first of these deposits was discovered in 1905, the latest discovery having been made in 1979. To the present (1983), some 16 Mt (17.7 million st) grading 1.33% Cu, 7.5% Pb, 14.5% Zn, 115 g/ t (3.7 oz per ton) Ag, and 1.4 g/t (0.04 oz per ton) Au have been mined. Mining operations are now largely terminated, but a few hundred thousand tons of economically marginal reserves may be mined in a salvage operation. The Geological Association of Canada Special Paper No. 22, "The Buchans Orebodies, 50 years of Mining and Exploration," contains papers which describe the history, geology, and the application of evolving geological concepts in exploration. Papers by Neary, Swanson, and Thurlow and Swanson in that volume are topical to the present discussion. Successful exploration techniques at Buchans included physical prospecting, utilization of the state-of-the-art geophysical techniques, saturation diamond drilling which was made possible by the high gross value of the existing ore, and, since 1955, diamond drilling directed by fairly well understood geological parameters. The record of discovery started in 1905 when the Buchans River deposit was found by Matty Mitchell, a prospector employed by the Anglo- Newfoundland Development Co., a British company which owned mineral rights over a very large area in the Red Indian Lake-Exploits River drainage system.

Jan 1, 1991

By Frank Kneeland

SAFETY FIRST is a popular motto-most mining companies have adopted it. It is probable, however, that in the majority of cases it is only a motto and gets no further than the office stationery or the bulletin board at the mine's entrance. In but few industries is there employed a greater diversity of machinery and mechanical devices than in coal mining. The list ranges all the way from mechanical stokers to wood-working machinery and undercutters. Many of these devices, particularly those employed in wood working, are extremely dangerous. In 1913, 23 per cent. of all fatalities occurring in coal mining in the U. S. were caused by machinery of some sort or other. Although the forms of accidents occurring with mining machinery are legion, they generally arise from one or more of five causes: (a) Falls from ladders, platforms, etc.; (b) coming in contact with moving machines or parts thereof; (c) electric shocks; (d) failure of some machine part; (e) mismanipulation of valves, levers, switches or other hand-operated controlling devices. The steps which may be taken to prevent accidents from the above causes are almost as numerous as the accidents themselves. There is, and can be, no panacea for all mishaps, nor for any one class of accidents. There is no mathematical or other formula that will bring immunity under any set of conditions. Common sense is the only guide. The remedy for the first-named class of accidents is simple and generally effective-namely, make the staging, ladder, platform, or other support, abundantly strong to carry any possible weight that it may be called upon to bear; provide ample railings on platforms or runways, and non-slipping feet on movable ladders.

Jan 1, 1915

INTRODUCTION The International Finance Corporation (IFC) is affiliated with the International Bank for Reconstruction and Development (World Bank) but operates with a separate staff and funding. It supplements the activities of the Bank by providing, to private business, equity and loans without government guarantees in whatever form and combination most suited to the project. IFC frequently complements the Bank's activities by utilizing, for example, the Bank's public sector infrastructure activities to support IFC's private sector projects. In the case of local financial institutions especially, IFC collaborates with the Bank by providing technical and financial assistance. IFC is the world's largest multilateral organization which finances private sector business in developing countries. IFC's fundamental purpose is to promote the economic development of its developing member countries through the support of the private sector. Of the 124 member countries of IFC, more than 100 are developing countries. Since it began operations in 1956, IFC has been associated with more than 2,000 companies and financial institutions in supporting over 700 business ventures in more than 80 countries. The total capital costs of these projects exceeds $26,000 million. In the 1984 fiscal year, IFC approved 62 projects in 37 countries with a total project cost of $2,473 million. IFC will make investments only if sufficient capital cannot be obtained on reasonable terms from other sources. IFC often serves as the catalyst for a project by encouraging other investors--from inside and outside the host country--to make their own equity investments along with the local sponsor for a particular project. IFC'S SPECIAL ROLE The significance of IFC's role extends beyond just its financing and technical assistance: IFC's capability to raise investor confidence in a project and to help all the participants to arrive at mutually satisfactory investment arrangements is its distinctive character. Direct Investments IFC invests in all types of projects both large and small. Heavy industrial ventures not only supply essential materials and equipment for other domestic enterprises, but also earn foreign exchange through exports. In recent years, increased emphasis has been placed on agriculture and agribusiness products, aquaculture, food and food processing, and other renewable and nonrenewable resources such as metals and energy. [ ] An overall objective of IFC is to assist entrepreneurs and others in the private sector raise the needed capital for business ventures. IFC does not compete with, nor seek to replace private initiative and capital. Rather, IFC helps to raise funds in order to undertake projects that would otherwise be held back by the lack of adequate funding. IFC can do this in several ways: IFC can invest in equity and make loans for its own account. But beyond that, IFC can reach out into the international capital markets in search of additional capital. Because of IFC's 25 years experience and record, outside investors who might otherwise be

Jan 1, 1985

By Garrett R. Hyde, Aleksandar Stojsic

Introduction Economic pressures in the international marketplace have spurred advances in almost every facet of flotation. New developments have occurred in flotation chemicals, flotation machines, and in the application of automated process control technology to grinding and flotation. Many of these advances are the results of concerted efforts to apply the knowledge obtained from basic flotation research over the past 15 to 20 years, to develop industrial technology for the more efficient separation of sulfide minerals in real ores. Mining company executives and equipment manufacturers are being called on to make decisions for incorporating some of this technology into present operations. This discussion is limited to two developments now at the stage of being engineered into industrial scale operations. They are control of the electrochemical environment or redox potential of the slurry, and control of bubble size in column flotation. Potential economic impacts are noted. Froth flotation Froth flotation makes use of differences in the surface properties of finely ground minerals to obtain separation. If the mineral surface is water repellent, the mineral particle will stick at the air-water interface of a bubble and float. If a mineral surface is not naturally water repellent, a chemical collector is added to the slurry to make it so. The collector must adsorb on, and make water repellent only the mineral to be recovered, not the gangue minerals. To achieve this degree of selective adsorption, chemical modifiers may have to be added to the slurry. Modifiers include pH regulators, activators, and depressants. Electrochemical control One of the most significant developments in recent years in the area of mineral processing technology is the recognition that collector adsorption of sulfide minerals is an electrochemical process. Consequently, flotation of these minerals depends on the electrochemical or redox potential of the system. Many of the modifiers used to control various flotation processes are actually potential controlling reagents. For example, the role of well known depressants, such as cyanide, sodium hydrosulfide, and sulfur dioxide, is essentially to

Jan 7, 1987

By J. Katzur

Recently in Germany, novel artificial humus in combination with water-storing hydrogels has successfully been tested as soil improving material in pot experiments. The novel artificial humus (NOVIHUM®) is derived from lignite through oxidative ammonolysis. The product contains c. 5.5% nitrogen. Using NOVIHUM® as fertiliser, variable amounts of the contained nitrogen are gradually available to the plant, depending on the hydrolysis rates of the different N-compounds. NOVIHUM® is a unique combination of long-term fertiliser and stable humus. The tested hydrogel is a polyacrylate/poly-amide copolymer, which is able to improve the water holding capacity of the soil and to retard significantly desiccation. In May 2000, in Germany (Aue region), an experimental site was set up under extremely difficult growing conditions for trees (Quercus petraea) on a uranium spoil pile of the mining company WISMUT Ltd. The oak plots treated with NOVIHUM® and hydrogel showed increased total increment-values, which mainly are the result of the second growth phase. Obviously, these plants profit from the favourable physical parameters of the substrate and the use of the novel artificial humus as nitrogen source. The oak trees can better use the plant-available NH4-nitrogen released from the artificial humus during the planting year. In Greece, an experiment was set up in December 2000 aiming to the afforestation (Pinus nigra, Abies cephalonica) of a bauxite spoil pile of SILVER & BARYTE ORES MINING Co. S.A., on the Parnassus Mountain. The scope was to demonstrate, that the above soil improving materials are also appropriate for the recultivation of sites under extreme climatic and orographic conditions. The first results revealed, that where NOVIHUM® and hydrogel were combined, plant growth was greater than the average. The one-year results of the experiments fulfil our expectations concerning the application of NOVIHUM® in combination with hydrogel for the afforestation of problematic sites, such as the south-exposed steep slopes of the spoil piles of uranium mining. They may represent the most detrimental sites for afforestation in Europe.

Jan 1, 2002

By Mackenzie W. R, Harding C. G

The Islamic Republic of Mauritania is a large country of over 1 000 000 square kilometres situated on the Atlantic coast of north-west Africa. It is bounded to the north by Western Sahara and Algeria, to the east by Mali, and to the south by Mali and Senegal. With the exception of a narrow strip in the south along the Senegal River valley, the country lies entirely within the Sahara. The north of the country is largely devoid of vegetation, and it is estimated that 90 per cent of the population of 2.1 million people live in the southern quarter of the country. From about the turn of the century, Mauritania was ruled by the French from Dakar in Senegal and, until 1960 when it obtained independence from the French, Mauritania did not have a capital. Today, the capital is Nouakchott, home to an estimated 600 000 Moors of mixed Arab, Berber and African descent. After independence in 1960, disputes over Spanish Sahara to the north led to a military coup in 1978 and it was not until 1991 that a democratic constitution was adopted. The new constitution declares Mauritania to be an `Islamic, African, and Arab Republic.' It provides for an executive president, elected for a six-year term, and for a bicameral legislature, consisting of a national assembly and a senate. The first presidential and legislative elections were held in 1992 under United Nations' supervision. Mauritania's economy is predominantly pastoral, and the country depends heavily on foreign aid. Its principal export industries are iron ore mining (about ten million tonnes per annum from mines near Fderik in the north) and fishing. Mines d'Or d'Akjoujt SA (MORAK), a company in which General Gold Resources NL (GGR) has 42.5 per cent equity, produces over 50 000 ounces of gold per annum, which represents the third largest export industry in the country.

Jan 1, 1996

Maps and Mining Data for the Library. I suggest that the Institute Library can increase its usefulness by systematically soliciting from the engineers and mining companies all published reports and maps, and parts of reports and records, not of a private or confidential nature. If this is done an engineer assigned to report on a well-known property or district may depend on finding at the library a large amount of preliminary data and general information from these official and engineering reports relating to his prospective investigation. In many mining reports a large part of the report is of a general technical and scientific character, and there could be no good objection on the part of either the engineer, or his client to making such information thus of record. I believe there would be a great deal of information furnished by the engineers if they were properly solicited under this plan. I have found on different occasions that much work could be saved by such records now in the Library. The plan would also have the advantage of keeping the Library in closer touch with the active engineers, a feature to be desired. I also have in mind that the Library should undertake to collect all the prospectuses and financial literature which is issued in connection with mining. Of course a great deal of this is unreliable, but even this is valuable for record in the matter of legal and other investigations. I shall be glad to co-operate with you, and do anything I can to develop more in detail the general ideas above noted. Yours very truly, KIRBY THOMAS NOTE.-The Library of the Institute makes a specialty of collecting and filing material of this character, and the letter printed above is brought to the attention of members in the hope that they will co-operate by sending in copies of maps, reports of properties, etc.

Jan 11, 1913

By Olgac Kangal, Ali Guney, Gulay Bulut, Guven Onal, Ayhan A. Sirkeci

"This paper presents the results of pilot scale column flotation applications in the two different copper concentrators in Turkey. The Kure Copper Plant is located in the Black Sea Region of Turkey. There are four types of copper ore formations in the Küre region. The so called disseminated ore contains 60-70% siliceous minerals of which Cu content is around 0.5%. The remaining three ore types in the region are generally named “massive ores”. The massive ores may assay up to 15% Cu and the major gangue mineral is pyrite associated with relatively little amount of silica. The main copper mineral in all formations is chalcopyrite that is generally finely disseminated in pyrite therefore satisfactory liberation requires ultrafine grinding especially in the case of the massive ores.A blend of these ores, containing 1.7% Cu on average, is fed to the Küre Copper Concentrator whose capacity is 1.2 million tons of ore annually. Unfortunately, today the plant operates below its designed capacity treating around 550,000 tons of ore per year. The design of Küre Copper Plant was undertaken by the Outokumpu Company of Finland. The operation of the plant is almost automatically controlled and the feed, the concentrate and the tailings are assayed for copper by on-line XRF analysers. The particle size analysers are also connected to the grinding circuit. The feed material is ground almost below 50 µm and the flotation is conducted around pH 11.2 using Hostaflot X-231 (a trade mark of Hoechst) as the collector. Apart from the rougher cells, there are four cleaning stages after which the final concentrate is produced. A very fine grinding requirement for an adequate level of liberation makes successful flotation difficult and consequently the final concentrate can hardly assay above 16% Cu leading to copper losses around 20% in the tailings that contains 0.3% copper."

Jan 1, 2003

By C. P. Bowie

During the period of 10 years from January 1, 1908, to January 1, 1918, approximately 12,850,000 barrels of oil and 5,024,506,000 cubic feet of gas were destroyed by fire in the United States, entailing a total estimated property loss of $25,254,200. During this period 503 fires were reported. As is shown in Plates I and II, 310 of these fires were caused by lightning and 193 by all other causes. The losses from the fires caused by lightning were estimated to be $11, 148,000, and from those due to all other causes $14,106,200. Directly and indirectly, the fires resulted in the deaths of nearly 150 persons and were responsible for almost as many more being permanently disabled. For the past three years the Bureau of Mines has been conducting investigations to determine the nature and the specific causes of these fires, with a view to suggesting means whereby they may be suc- cessfully combatted and, in some places, perhaps eliminated entirely. As the subject of oil and gas fires is necessarily broad, no attempt is made in this bulletin to treat it exhaustively; rather the bulletin aims to point out what has been done by operators in the past, and to describe various fire-prevention methods and fire-fighting appa- ratus which are being used or adopted by many of the larger oil companies. These methods and apparatus, it is believed, if uni- versally employed by operators, will largely decrease the present enormous annual losses. In the discussion of oil-well fires, the methods used in extinguishing several of the larger and more perplexing ones are described. As the right procedure for extinguishing any oil-well fire must be de- termined largely by local conditions, it is not probable that all of the methods used at some one fire, as described, will be applicable to a future fire. However, the operator, from these descriptions, may at least gain suggestions that will greatly assist him in fighting similar fires.

Jan 1, 1919

By Steve Karl

Introduction US steel production dropped 5% in 1985 to 79 Mt (87 million st). US operators are producing at only about 65% of capacity. More than 600 steelmaking facilities have closed in just 10 years. And McDonalds Corp. now employs more people than the entire US steel industry's 200,000. Not gloomy enough? Well, the North American iron ore industry can expect more plant closures and capacity reductions in the coming years. And don't count on the Federal government's voluntary restraint agreements with foreign steel producers to bail out the industry. In 1985, the first full year of the restraint agreements program, steel imports were more than 25% of domestic consumption, well above the 18.5% target. That's the grim truth, according to M. A. Hanna's Robert F. Anderson. Hanna's chairman was speaking to a group of iron ore, taconite, and steel industry executives at the Minnesota Section AIME meeting in Duluth in January. Despite those depressing facts, Anderson said he believes the domestic iron ore and steel industries can survive, although they will both be shadows of their former selves. But, he is giving them five years to make the necessary adjustments or both will die. Major steel producers during the last four years have added about $7 billion in losses to their books, he said. In Minnesota's Iron Range, employment in iron ore and taconite has gone from 14,000 10 years ago to less than half that today. Anderson explained that steel producers have more capacity today that more than meets their demand for iron ore. This places great pressure on iron ore producers to restructure to survive. Hanna, for example, has been forced to close or divest its iron ore interests in Missouri, Michigan, Canada, and Minnesota since 1980. The latest casualty was the company's Butler taconite project in Minnesota. "In just five years we've reduced ownership of active pellet capacity by 80%," he said. Technological ironies Improved technology is one cause of the industry's woes, Anderson said. While these improvements are welcome in terms of remaining competitive, the irony is that some of these technological improvements are coming at the expense of the iron and steel industries. There is a growing demand for lighter and less expensive substitutes for steel. Automobiles contain about 318 kg (700 lbs) less steel than they did 10 years ago. And, Anderson said Ford Motor Co. has indicated it plans to reduce steel usage an average of 50 kg (112 lbs) per car in the next few years. One leading steel analyst has predicted that steel usage in cars will fall another 40% in the coming years. Improved steelmaking technology has also decreased raw steel production. Continuous casting is more efficient than traditional forms of steelmaking, Anderson said. Continuous casting accounted for about 43% of steel production in the US last year, compared to 9% a decade earlier. And, Japan and Korea are producing more

Jan 3, 1986