Search Documents

"Real time analysis of conveyed bulk materials can be used to improve process performance by reducing variability and upgrading ore quality through selective removal of increments of flow that do not meet appropriate selection criteria. This paper focusses on proven Prompt Gamma Neutron Activation Analysis (PGNAA) and microwave transmission technologies used to representatively measure conveyed ore quality in real time so that meaningful decisions can be made between the mine and mill. This enables the effective removal by bulk diversion of small increments of conveyed flow such as waste, highly deleterious material or sub-economic material from the mill feed. Improved ore quality in plant feed optimises process performance, reduces processing costs and minimises tailings generation. Analysis is unaffected by particle size, dust, layering or segregation, mineralogy and belt speed. Technologies are explained and performance examples given from installations in copper and iron ore. The technology has been used successfully in bulk sorting for over twenty years typically using measured increments of a few minutes. Improvements in technology and calibration performance have resulted in accurate measurements over increments of thirty seconds and below.INTRODUCTION Ore quality variability exists on a number of scales. Block model grades represent a few hundred to many thousands of tonnes. Grade control at the mine occurs on a scale typically down to the size of a haul truck, which may be a few hundred tonnes. Highly variable ore quality is detrimental to process efficiency and effectiveness. Processing waste or low grade ore when higher quality feed is available represents a lost opportunity to generate higher revenues earlier in the operational life. Measuring ore quality accurately over short time increments during conveying enables small increments to be measured and diverted according to their quality. The paper explains the technology and benefits. Neutron irradiation techniques were considered potentially suitable for conveyed bauxite measurement by Beurton et al, 1995. Tran & Evans (2001) concluded there was no equivalent technology to Prompt Gamma Neutron Activation Analysis (PGNAA) in terms of material penetration power. PGNAA was evaluated by Nelson & Riddle (2003) for possible use in the phosphate industry and recommended its use for further characterisation of the mine’s various ore types to improve stockpile allocation and grade control. Cottle (2007) discussed test work for an iron sinter application and Delwig et al (2011) described the successful installation in 2009 and performance of PGNAA for base-to-acid ratio control in sinter feed with the analyser output used to control lime addition. Geoscan (PGNAA) works very well on iron ore and can “improve control over what is happening in the plant” and that comfort can be provided in knowing that the product is on-spec according to Minnett (2010). PGNAA is not yet used in the minerals sector for tariff purposes as has occurred since 2000 with Coalscan (PGNAA) in coal (Minnett, 2010)."

Jan 1, 2017

By Richard F. Link, George S. Koch

Advantages and disadvantages of deflecting (wedging) diamond-drill holes to obtain sampling data are compared with the alternative of drilling additional holes. The discussion is based on a statistical analysis of a large set of deflection data from exploratory boreholes in South African gold mines. Representative cost comparisons show the conditions under which deflections are likely to be desirable.

Jan 1, 1969

By Gordon L. Kidd

The object of this paper is to show the relations of the East Coulee coal area to the near-by Willow Creek, Wayne, Rosedale, and Drumheller areas, all being parts of the Drumheller field. The word ?area? is here used in a more local sense than that employed by Dr. J. A. Allan, whose. 'area' is rather comparable with the 'mining division' in British Columbia. I have drawn freely from the published information, particularly from Dr. Allan's report on the "Geology of Drumheller Coat Field, Alberta", and from Dr. E. Stansfield's paper on " A Chemical Survey of Alberta Coals", to whom thanks are due. The Drumheller field is served by branch lines of the two principal Canadian railways. The C.N.R. traverses the district by its Goose Lake line from Calgary to Saskatoon; and the C.P.R. by a line from Calgary to Acme and then southeasterly to Drumheller, where it effects a junction with the C.N.R., over which the C.P.R. has running rights as far as Rosedale. From Rosedale, a joint line built during the summer of 1928 extends about forty miles down the Red Deer river to the mouth of Bull Pond creek. From that point the C.P .R. turns more southerly to connect with the Bassano-Empress line. The C.N.R., it is expected, will eventually proceed eastward to connect with a transcontinental line. The joint line from Rosedale down the Red Deer river opened up the Willow Creek and East Coulee areas.

Jan 1, 1929

By K. K. Kelley

This work is both a revision and an elaboration of Bureau of Mines Bulletin 371, which was published in 1934 and included data available to October 1933. During the intervening years, a large number of new experimental, high-temperature, heat-content data have become available through continuous, systematic efforts of the Pacific Experiment Station of the Bureau of Mines and the Laboratory for Inorganic and Physical Chemistry of the University of Groningen (Netherlands), coupled with various individual investigations at many institutions. In addition, calculations from spectroscopic and molecular constant data have been extended and applied to a wide variety of gaseous substances. This bulletin purposes to collect and correlate all available high-temperature heat-content and specific-heat data for inorganic sub-stances and to formulate tables and algebraic expressions for their representation. It is hoped in this manner to remove some of the tedium of thermodynamic calculations for industrial metallurgical research workers and engineers who often have available only an inadequate library in this field. It is expected also that this bulletin will have value to those teaching courses in metallurgical and chemical thermodynamics.

Jan 1, 1949

By S. S. Peng

In this paper, the precise definitions for a number of commonly used subsidence parameters are given. The subsidence parameters have been determined using an integrated approach for 110 subsidence cases collected in the major US coal fields. Attempts have been made to establish empirical formulae for the parameters. The results of this study indicate that some traditionally-held concepts should be changed.

Jan 1, 1995

By F J. Kelly

A chemical process, based on laboratory investigations, is proposed for the production of high-purity niobium oxide from a pyrochlore-perovsk1te flotation concentrate produced from ore obtained at the Oka, Quebec property of Columbium Mining Products Limited. The method developed included the decomposition and dissolution of the flotation concentrate with hot, concentrated sulphuric acid. The dissolved niobium was purified and concentrated by a solvent extraction step, using methyl isobutyl ketone as the extractant. The niobium was recovered from the extractant with ammonium fluoride solution from which niobium oxide was precipitated with ammonia. Finally, the filtered and washed precipitate was calcined. Ninety-six per cent of the niobium was recovered in a product analysing 99.9 per cent Nzo.. The reagent cost was in the range of $1.00 to $1.25 per pound of niobium recovered. Introduction OVER the past few years, Columbium Mining Products Limited has been engaged in the development of a niobium-bearing mineral deposit in the vicinity of Oka, Quebec. One phase of this program resulted in a flotation process capable of producing concentrates containing up to 50 per cent Nb205? Flotation pilot-plant

Jan 1, 1965

By H. Golzarpoor

Life Cycle Analysis (LCA) is a methodology for evaluating the environmental impacts associated with a product during its life cycle. LCA is identified as the most reliable method for verifying environmental impacts; however, current LCA-based approaches have certain limitations for environmental analysis of construction products. Integration of the LCA methodology with Discrete Event Simulation (DES) provides a sound framework for modeling and analysing the environmental impacts of construction products. LCA and DES is one possible combination for analysing the cause and effect of various scenarios where time, resources, and randomness of input variables affect the outcome and, therefore, has the potential to address the shortcomings of LCA in construction. Recent studies in disciplines other than construction such as manufacturing systems have revealed positive effects on evaluation of environmental metrics while integrating LCA with DES; however, this integration has not yet been applied for environmental analysis of construction products. By implementing LCA data in a DES model, this research proposes an environmental model of earthmoving operations in a case study. Environmental variables are simultaneously assessed with production variables in the same simulation model and the integration of DES and LCA is discussed.

Aug 1, 2013

By James R. Strong

Before getting into the subject of packaging and materials management, please permit me to introduce you to MICRO SWITCH. MICRO SWITCH, A Division of Honeywell Inc. is located in Freeport, Illinois. We manufacture and market thousands of types of precision snap-action electrical switches. Most of them are used as components by other manufacturers in industrial and commercial products. MICRO SWITCH also offers a broad line of industrial control devices including heavy- duty limit switches, relays, manual controls and proximity switches. Other product lines are solid state keyboards for the computer industry and high-performance d.c. motors used in computer related equipment. So you can see that we are a component manufacturer. With the exception of the keyboards, every one of our products would "fit comfortably into a breadbox." Some are so tiny that one could easily fit several thousand into a man's hat. In my position as supervisor-packaging. package design, and materials handling engineering, I am actively involved in package design projects, parts handling design projects, and numerous activities involving departmental layouts, storage facilities, and material handling equipment. Two package design technicians, a materials handling engineer, and a materials handling technician make up the technical staff.

Jan 1, 1973

By O. Leuangthong, E. Schnetzler

"The McMurray formation in the Athabasca oil sands deposits of northern Alberta is part of the world’s second largest proven crude oil reserves. The formation is characterized by stratigraphic layers that correspond to three different depositional environments: Marine, Estuarine, and Fluvial facies. Resource estimation for oil sands has traditionally relied on polygonal and inverse distance schemes. These techniques are simple and straightforward in practice, but they do not permit reliable uncertainty assessment. This paper describes the modelling of the McMurray formation using modern geostatistical techniques.Geostatistical modelling should be performed within homogeneous geological facies. The methodology for geostatistical simulation within each of the identified facies involves: 1) assessing the most appropriate stratigraphic transformation for optimization of the correlation structure; 2) determining representative distributions with declustering and debiasing techniques; 3) modelling spatial continuity of the bitumen grade, fines grade, water saturation, and other petrophysical variables; 4) performing estimation and cross validation as checks against simulation results; 5) performing simulation for uncertainty quantification of bitumen and fines grade; and 6) model checking of simulation results against the input data, and comparisons against the kriged models. These steps are described in detail. The application of these models for uncertainty quantification in support of resource classification is also discussed."

Jan 1, 2006

By P. Zhang, D. W. H. Su, M. Van Dyke, H. Dougherty

To provide critical scientific data and engineering guidelines to federal and state regulatory agencies as well as the coal and gas industries, the National Institute for Occupational Safety and Health (NIOSH) initiated a Gas Well Stability Research Program in 2016. This paper summarizes the critical scientific data acquisition, interpretation, and modeling by NIOSH regarding the stability of unconventional shale gas wells influenced by longwall mining. Currently, NIOSH is the only organization in the U.S. conducting such fundamental and impactoriented research, which receives input and collaborations from MSHA, PADEP, WVDMS, OHDNR, the coal industry, and the gas industry. Results from the NIOSH field instrumentation programs—which include surface, subsurface, and underground instrumentation—and the parallel three-dimensional numerical modeling programs indicate that, under shallow and medium covers, the measured horizontal displacements within the abutment pillar are one order of magnitude higher than those measured under deep cover. Casing couplers are found to play an important role in longwall-induced casing deformations. Cementing alternatives are found to have significant impact on longwall-induced casing stresses and deformations. Measured 60-arm caliper logging results are in good agreement with three-dimensional computer simulation results. Engineering guidelines on longwall-induced deformations, casing and cementing alternatives, gas well setback distances, as well as risk assessment strategy are proposed.

Mar 2, 2022

By E. Hasanbas

Vibrating screens and crushers are the workhorses of material sizing. Unfortunately their natural frequency is often in the range of typical supporting structures, thereby making installations prone to vibration problems. Much of the available literature regarding the support of vibrating screens is fairly confusing and outdated. This paper presents the results of utilizing accelerometers and finite element software in the analysis and design of supports for vibrating equipment. It contains data from field studies of vibrating screen and crusher installations, design of new and repair of existing supporting structures, and the correlation between field data and finite element time history analyses. Finally, the paper summarizes a method for analyzing and designing structures subjected to vibratory loads and predicting their behavior.

Feb 23, 2014

By Liiban A. Affi

The most difficult task of designing multilevel tieback walls for deep excavation support is the determination of lateral stresses. These lateral stresses act not only on the shored height, but also on the embedded portion of the soldier pile, all the way down to the pile tip. Examples of lateral stresses include uniform surcharge load (soil spoils or equipment), strip load surcharge from Cooper E80 (train loads), line load surcharge (exterior footing or retaining walls), and point loads (cell tower). In this paper we will discuss the various surcharges, do step by step example calculations and show how to take the total lateral stress output and present the design pressures for direct use by the substructural designer. Included is a case study from a project Anaheim Hills, California, USA.

Jan 1, 2010

By L Basnayaka, N Subasinghe, B Albijanic

"It has been recognised that the presence of clay minerals in ores adversely affect flotation performance. In this study, changes in rheological properties of the flotation pulps under normal operating conditions were studied with additions of bentonite and kaolinite clays at various concentrations. Zeta potential measurements were also carried out to determine the changes in surface charge due to adsorption of clay particles. The results showed that bentonite clay adversely affects floatability of pyrite while kaolinite clay had a lesser influence on flotation of pyrite. The addition of Ca2+ ions to the pulp containing bentonite modified the rheological characteristics and in turn improved the pyrite flotation. It was also observed Ca2+ ions suppressed the swelling properties of bentonite and altered surface charge properties of bentonite clay particles. It has been shown that the flow index affected the ultimate recovery and it may provide a means to monitor flotation performance in routine plant operations.Citation:Basnayaka, L, Subasinghe, N and Albijanic, B, 2016. Effect of Clay Rheology on Flotation of a Refractory Gold Ore, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 77–84 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

Can mining promote sustainable development? What is sustainable development? Is sustainable development good for corporate sustainability? Does it work in practice? If so, is it good for business? This paper does not seek to provide definitive answers to these issues. Rather, it is presented in the interests of sharing information and contributing to the pool of collective experience. The discussion will draw on the experience of Placer Dome in Papua New Guinea (PNG). Sustainable development means development that is maintained at a steady level without exhausting natural resources or causing ecological disturbance. The term æsustainable developmentÆ is often linked to the concept of ecological equilibrium, development that is self-replenishing. While its essential meaning remains the same, in practice, and for todayÆs complex and industrial world, different people will interpret sustainable development in different ways. Given the dynamics of development and the competing social, political and economic interests, sustainable development must be seen from a much broader perspective. This is the point that this paper will attempt to make. Mining, an activity that uses non-renewable resources, can promote sustainable development. The 1987 Brundtland Report (also known as the Report of the World Commission on Environment and Development), defines sustainable development in a broader manner - as development that meets the needs of the present world without compromising the ability of future generations to meet their own needs (Elkington, 1997). This definition calls for inter-generational equity in the development and use of resources by many organisations, including multinational corporations. Corporate sustainability, on the other hand, is about developing strategies that guide a corporation to stay alive and, more importantly, to stay ahead of its competitors. It is basically about survival in a competitive social and commercial environment. In a corporate world, profitability is survival. In this context, corporate profitability, the main ingredient of corporate sustainability, is important for sustainable development. Without profits, corporations will find it difficult to practice sustainable development or indeed any development. Sustainable development can integrate mining activities with the rest of the community, add value and, in the long-term, profits to the bottom-line. Ultimately, sustainability will force corporations to adopt strategies based on a longer time scale to survive. In the mining sector, corporate sustainability depends on a close relationship with all stakeholders, particularly landowners for whom sustainable development is critically important. Increasingly, there is an acceptance of the view that success is not achieved simply through competition in price, cost and technology but, more importantly, through creating social infrastructure which support community ethics, norms and values essential for trust and partnership. Needless to say, mining companies that engage in appropriate community-based development in support of inter-generational justice recognise the true value of sustainability. This is sometimes called the æhuman sustainability approachÆ which underlines the critical significance of trust in relationships with stakeholders and continuous improvement of corporate capabilities directed towards the future (Dunphy and Griffiths, 1998). In the long-term, such development will enhance corporate public image and acceptability. In practice, both concepts can be built on the principles of economic viability, environmental quality and social justice -what, in todayÆs parlance, is increasingly becoming known as the ætriple-bottom-lineÆ approach to business (Elkington, 1997). Underpinning this approach is a process of continuing dialogue and co-operation between governments, non-government organisations (NGOs) and business.

Jan 1, 1999

By Richard S. Dennis

Acid recovery employs ion exchange (I-X) resin as separation media for inorganic acids from dissolved metallic salts by physical adsorption and without the use of chemicals. This technology has been used for years on spent etching and plating liquors to recover acid for reuse in the bath and to reduce waste acid neutralization costs. It is also used for electrolyte treatment to facilitate valuable metal recovery via acidity reduction. TETRA's ccrxr'" I-X contactor has been used successfully for acid separation from its metallic salt counterpart in a simple, continuous operating mode using strong base anion resins. Efficient separation is enhanced by acid reconcentration to nearly its original strength or as high as 14-20%. Continuous treatment also recovers heat to the tankhouse or bath and improves metal quality due to consistent acid quality. Conventional fixed bed ion exchange (I-X) systems are impractical for acid recovery because of complex control design and large resin inventories needed to process very low liquid-to-resin treatment ratios associated with strong acid concentrations.

Jan 1, 1996

By Fuqiang Zheng, Feng Chen, Wenting Duan, Yufeng Guo, Tao Jiang

High-quality titanium-rich material is of significance in the development of titanium industry as it is the main raw material to produce sponge titanium and titanium white using chloride process. Activation roasting of titanium slag with high Ca and Mg contents as adding H3PO4 followed by acid leaching was investigated to prepare titanium-rich material. The effects of H3PO4 dosage, roasting temperature and time, hydrochloric acid quantity, acid leaching temperature and time on TiO2 grade and removal of impurities were studied. The results show that after the finely ground titanium slag roasted with 8% H3PO4 at 1000 for 2h, most Mg impurities in anosovite solid solution structure were converted into simple acid–soluble compounds. The impurities such as Ca and Mg obviously decreased when the hydrochloric acid concentration was 20%, leaching at 100 °C for 2h, from which a titanium-rich material containing 82.56% TiO2 and 1.15% (CaO+MgO) was obtained.

Jan 1, 2016

By Jeffrey C. Evans, Daniel G. Ruffing, Hejintao Huang

Soil-bentonite slurry trench cutoff walls are the most common type of vertical cutoff wall used in the US for seepage control and for passive control of contaminant migration at environmental sites. Design considerations are often limited to constructability considerations and a target hydraulic conductivity. With design-build contracts common, the backfill design is often left to the contractor. As a barrier soil, the hydraulic conductivity of bentonite slurry wall backfill is typically required to be equal to or below 1x10-7cm/s. The importance of stress state upon the hydraulic conductivity as well as the expected stresses are both established in the literature. Grain size distribution of the base soil and bentonite content both affect compressibility and hydraulic conductivity. This paper describes the results of studies undertaken to evaluate the interrelationships between compressibility, hydraulic conductivity, grain size distribution, and bentonite content. Three base soils were used representing a range of soils found on typical construction projects. Using these base soils, mixtures containing a range of dry bentonite contents from 0% to 5% were prepared to a slump consistent with field practice. The compressibility and hydraulic conductivity were measured in consolidometers adapted for falling head permeability tests at the end of each load increment. These experiments yielded the relationship between effective stress and hydraulic conductivity as well as consolidation characteristics including time rate of consolidation and coefficients of compressibility. The experimental results are then used to indirectly evaluate stress development and to assess the time needed for consolidation. The findings show a substantial decrease in hydraulic conductivity as effective stress increases, regardless of base soil type and dry bentonite content, a relative insensitivity of stress development to backfill compressibility, and a wide range of values for coefficient of consolidation depending upon backfill mixture and stress level.

Jan 1, 2016

This report summarizes the work performed and results achieved on the above contract from October 18, 1971 through July 14, 1972 under Phase II, Task 1: Detailed Design of Prototype and Task 3: Supporting Experimental Investigation. Operation and Service Manuals resulting from Task 3 are submitted under separate cover as are detailed design drawings and specifications, prepared under Task 1. Both items accompany this report. This report also includes (A) an estimate of the cost of construction, (B) a description covering the use of the equipment, and (C) a proposed test plan to demonstrate performance of the equipment in both the laboratory and a mine.

Jan 1, 1972

By Robert S. Thomas, Bernard M. Tarralle, Nasser Massoudi

"The Commonwealth of Virginia is restoring and expanding its Capitol of great historic significance. Designed by Thomas Jefferson in 1785, it is the second oldest Capitol building in the United States. The building expansion required excavations immediately adjacent to its South Portico. The building, which rests on shallow brick footings, is very sensitive to any disturbance caused by construction and excavation. A comprehensive and secure plan of operations was devised by the design team to ensure that this national monument remains unharmed by the new construction. Various construction techniques were implemented to satisfy the strict movement goal of 0.25 inch and distortion of U2000. They consisted of jet grout columns to stabilize the upper soils, compensation grouting for future foundation leveling, a tied-back reinforced concrete diaphragm wall for excavation retention and foundations, and realtime instrumentation for monitoring. This paper describes the design approach for the retention system, providing information on the various construction phases and techn iques, and reports on the movements recorded by the real-time monitoring system during the course of the project. At the time of this manuscript preparation, and the deep excavation complete to final grade, the results indicate that the extremely restrictive building movement criteria have been met. The success can be credited to detailed design, close cooperation among the project team, prudent construction methods, and real-time monitoring. INTRODUCTIONThe Commonwealth of Virginia is undertaking a comprehensive renovation and expansion of the Virginia Capitol building located in Richmond, Virginia. The Capitol building was designed by Thomas Jefferson in 1785, with construction of the original building starting the same year. The Capitol building was designated a National Historic Landmark in 1960 and was listed on the National Register of Historic Places in 1966.A part of the comprehensive renovation and expansion of the Capitol is a 25,000-square foot, two-level subterranean extension on the south side of the Capitol building, which will serve as a new Visitor Center and public entrance for the Capitol. Deep excavations were required for the construction of the new Visitor Center. The excavation required a permanent retention system to accommodate an approximately 40- foot deep excavation."

Jan 1, 2005

By Daniel W. H. Su

"This paper presents results from a recent study conducted to evaluate the effects of longwall-induced stresses and deformations on the mechanical integrity of shale gas wells drilled over a longwall abutment pillar. The primary objective is to demonstrate that a properly constructed gas well in a standard longwall mining abutment pillar can maintain mechanical integrity during and after mining operations. Successful designs would allow for the safe recovery of both coal and gas reserves. Major elements of this comprehensive study include: (1) modeling of rock movements to predict impacts on gas wells, (2) measurements of actual rock movements at the surface and in the subsurface, (3) measurements of actual impacts on test wells designed similarly to real shale gas wells, ( 4) comparison of modeling results to actual rock movements to validate the model, and (5) employing the validated models to evaluate various casing and cementing designs to minimize casing deformations and absorb longwall-induced strains along the intermediate and production casings.A study site was selected over a southwestern Pennsylvania coal mine, which extracts 1,500-ft-wide longwall faces under about 600 feet of cover. Four test wells and four monitoring wells were drilled and installed over an abutment pillar with 125-ft by 275-ft centers. The four test wells were drilled to a depth of 642 ft, or 42 ft below the Pittsburgh seam, and were designed like a real shale gas well, except that only three casings (namely the surface, water protection and coal protection casings) were installed in each well. Casing steel grades, wellbore diameters and annular spaces were purposely varied in each of the four test wells to evaluate the effect of different well designs. The four monitoring wells - one vertical extensometer and three in-place inclinometers (IPI) - were drilled to different depths to measure the vertical settlement and horizontal displacements as a result of longwall mining on both sides of the abutment pillar. In addition to the test wells and monitoring wells, surface subsidence measurements and underground coal pillar pressure measurements were conducted as the 1,500-ft-wide longwall panels on the south and north sides of the abutment pillar mined by."

Jan 1, 2016