Search Documents

By W. L. Heidenreich

This report describes the methods and results of field investigations conducted by the Bureau of Mines between December 1956 and December 1957 on seven deposits of nickel-cobalt-iron-bearing laterite and weathered serpentine near the west coast of Puerto Rico east and south of Mayaguez. These deposits were named, for purposes of identification, Guanajibo, Punta Guanajibo, Las Mesas, north and south deposits of the Rosario Southeast group, and the west and east deposits of the Maricao Southwest group. In addition, the lower 17 miles of the Guanajibo River Valley was tested at widely spaced intervals for possible concentrations of magnetite and chromite in the alluvial sands. The objective of the investigations was to appraise, by drilling and sampling, the two largest deposits--the Guanajibo and Las Mesas. Testing of the smaller deposits was much more restricted. Field investigations consisted of mapping, drilling with power auger, sampling drill-hole sections, and pre-paring samples for chemical analyses, mineralogical studies, and metallurgical tests. The work was financed jointly under a cooperative agreement by the Bureau of Mines and the Economic Development Administration, an agency of the Puerto Rican Commonwealth.

Jan 1, 1959

By C. V. Jude

This U. S. Bureau of Mines (USBM) report presents results of stress analyses and field observations to investigate the effects of elevated trench drifts on the structural stability of rock mass zones surrounding a production draw drift in a mine utilizing a mechanized load-haul-dump (LHD) trench undercut panel caving system. A two-dimensional boundary-element mine stress model was developed to predict the locations and extent of damaged rock mass zones surrounding draw drifts where adjacent, parallel trench drifts are either elevated or not elevated above the LHD production draw drift level. A Mohr-Coulomb shear-failure criterion was obtained directly from in situ borehole shear test data. Hock-Brown shear-failure parameter values were computed from borehole-shear and triaxial test data. A procedure is described to estimate these parameters when a rock mass rating (RMR) value and triaxial data on intact samples exist, and no borehole shear test data exist Results indicate that trench drifts, elevated to the level equal to the height of the LHD production draw drift, would not minimize material damage nor significantly enhance the stability of rib and crown pillar zones surrounding production draw drifts in the mechanized LHD trench undercut caving panel investigated at this mine.

Jan 1, 2010

By D. Schreuder

Conditions in the South African market relating to atmospheric emission control has changed dramatically over the last 10 years. Companies have become more responsible, environmentally aware, and have to comply to more stringent environmental limits set by legislation. This paper describes briefly the current best available atmospheric pollution abatement technologies relating to particulates, acid gases, NOx, acid mists, aerosols, mercury, dioxins and furans. Mention is also made as to the best practices for product work-up and waste product disposal.

Jan 1, 2006

By Susan E. Brink

The first step in determining whether Mn can be recovered by in situ leaching is to develop and test a selective lixiviant. Two column leach tests and one core leach test Were conducted by the U.S. Bureau of Mines on Mn oxide ore using aqueous sulfur dioxide (SO2) as the lixiviant. The column tests showed that aqueous S02 could selectively dissolve available Mn oxides from calcite-rich ore in a heap leach system. However, the core test showed that calcite gangue side reactions can have pronounced negative effects on the likelihood of successful in situ leaching of a calcite-rich ore with aqueous S02. Petrographic and geochemical analyses showed that both Mn (IV, III) oxides and calcite were dissolved. The abundance of dissolved Ca caused precipitation of gypsum. Acid consumption by calcite dissolution caused a rise in pH that caused the SO/S species to shift to S032-(sulfIte), which hindered reductive dissolution of Mn oxide. Gypsum precipitation did not affect complete leaching of the rock fragments in the column tests; however, it plugged the natural permeability in the core. Manganese recoveries were high for the column tests and low for the core test.

Jan 1, 2010

By E. C. Payne

"IntroductionTHE SMALLER industrial and commercial steam generating plants in the United States are suffering from an ‘engineering deficiency' which, if allowed to continue, will probably result in the extinction of the species• that now burn •approximately 75 million tons of coal. We will classify as 'small' those plants which should require not more than one operating man per shift, including those in which as little .as thirty minutes per day should be adequate for .all service attention. These are the small steam plants that need the most, and get the least, expert attention for fuel :planning, equipment selection, design layout, .and proper operating technique. Dissatisfaction with bituminous coal is usually caused by one or more preventable weaknesses such as excessive or burdensome labour •for firing, .coal or ash handling and manual operation, smoke and fly ash emission above nuisance levels:, high maintenance and premium coal application for acceptable operation, and .finally, overall steam costs which are not .competitive. These 'deficiencies', so .common in the small coal-fired steam plants, can be readily eliminated by competent engineering and modern equipment with automatic controls."

Jan 1, 1953

By S. Atallah

A survey was conducted relating to the current practices for the classification of hazardous locations in coal preparation plants. Several plants processing bituminous, anthracite and lignite coal in Pennsylvania, West Virginia, North Dakota, Colorado, Montana and Wyoming were visited. Coal preparation plant operations and designers as well as MESA inspectors were interviewed. The National Electrical Code was discussed with selected members of the NFPA committee and electrical equipment manufacturers. Data provided by MESA on fire and explosion accidents in coal preparation plants were examined. The requirements of the pertinent Federal Regulations, National Electrical Code, National Electrical Manufacturers Association and Underwriters' Laboratories were compared and evaluated. This report consists of two parts. Part I: "Analysis and Review" provides a summary of the findings. Part II: "Recommended Guidelines" consists of recommended uniform guidelines that may be used for interpreting the National Electrical Code as it applies to the classification of hazardous areas in coal preparation plants.

Jan 1, 1977

By Gordon R. Sima

This contract is concerned with feasibility studies, design and fabrication of a prototype hand-held test instrument and a machine-mounted test Instrument for measurement of electrical shock hazards of mining machines. This report presents the proposed and detailed design of the hand-held test instrument and the machine-mounted test instrument. Theory of operation of each instrument is discussed and includes the operating parameters.

Jan 1, 1976

By Richard M. Foose

MOST of the roofing granules produced in Pennsylvania are made by two companies at three plants. The Advance Industrial Supply Co. has three quarries and a mill at Gladhill Station, in southern Adams County. The Funkhouser Company is actively engaged in mining, quarrying and milling at Charmian, about one mile west of Gladhill Station, and at Delta, in southern York County. These three plants produced approximately 100,000 short tons of granules in 1943. The production of roofing granules in 1937 for the whole country was only about 500,000 tons, generally indicating the large growth of the industry since that time. The fundamentals of producing roofing granules were discussed comprehensively by G. W. Josephson in a paper before the Industrial Minerals Division in October 1943 (Mining Technology, March 1944). The purpose of this paper is to describe the actual methods of mining the rock and milling it to make roofing granules, as practiced by the three Pennsylvania plants. MINING AND MILLING Funkhouser Company (Delta) The Funkhouser Company, near Delta, in southern York County, Pennsylvania, operates three joined quarries and a mine in the Peach Bottom slate. The joined quarries extend 1200 ft. in a northeast southwest direction along the strike of the slate cleavage and are about 200 ft. wide. The working face is about 45 ft. high. The quarrying operation is rather simple: Ingersoll-Rand Jackhamers, 1-in. and 1 1/4-in., with hollow drill steel, are used to undercut the quarry face with10-ft. holes. The face is "blown" and allowed to slump on the quarry floor. Loaded by a Marion electric shovel into trucks, the shattered rock is taken to the primary crusher 2500 ft. away. In addition to the normal quarrying operations, a drift into the northeast wall of the middle quarry was begun about 1935 and has advanced about 2000 ft. since then. Rooms have been driven at angles to the drift along choice beds of slate. The drifts and rooms have a roof more than 35 ft. high and the main drift and rooms are all more than 40 ft. wide. There is no cribbing at any place in the mine. Several of the rooms were driven upward on a 5º slope and in some of them there was stoping. Ingersoll-Rand Jackhamers are used, and only wet drilling is practiced. When visited in January 1940, an electric shovel was operating at the head of the drift, scooping up the slate blasted out of the working face. This, too, is trucked to the primary crusher. Some of the better quality slate is saved for making slate shingles. The primary crusher, which is a No. 30 McCulley gyratory, receives the slate from the trucks and crushes it to about 2-in. size (Fig. I). This product travels by a 30-in. belt conveyor to Niagara vibrating screens with 2-in. holes. The minus 2-in. product moves to a storage silo by bucket

Jan 1, 1945

By David A. Edgecombre

This paper discusses modern practices in the extrusion of steel. Particular emphasis is given to a description of the Ugine Sejournet method of extrusion, involving the use of glass as a hot work lubricant. Other methods are also mentioned. A brief history of extrusion is presented; present practices in the quality extrusion of tubing and solids are described; and the future potentials of the) process as a tonnage producer are briefly discussed. The advantages of extrusion and the reasons for the use of a glass lubricant, as well as the various methods of using glass, are given. The process, as described, is being used in the manufacture of large commercial quantities of stainless steel tubing and sections. This extrusion process is an essential and unique means of forming such atomic-age materials as titanium, zirconium, molybdenum and other super alloys all of which are materials required in the creation of nuclear installations.

Jan 1, 1963

To maintain its brand position in the competitive market of mining equipment, the Volvo Construction Equipment (Volvo CE) engineers were challenged to develop top-performing wheel loaders and articulated haulers even faster than before. To start, this meant reducing prototype test cycles by two-thirds. The final goal? Chopping in half the virtual prototyping time in early design phases. Creating a unified co-simulation solution In this ground-breaking project, the Volvo Construction Equipment design team in Eskilstuna, Sweden, replaced its piecemeal department-by-department process with a single solution based on LMS Imagine.Lab AMESim. With one unified model, they could simulate the behavior of four major vehicle subsystems in wheel loaders and articulated haulers: hydraulics, powertrain, thermal management and the actual driver. Subsystem models exchanged data seamlessly.

Jan 1, 2011

This Bureau of Mines report summarizes the research, development, and evaluation demonstrations conducted by the Bureau of Mines under the Health and Safety Act of 1969 to improve the means of notifying miners underground, who are away from their own phone, that they are being called.

Jan 1, 1977

By A. H. Harvey, M. Delangen, A. D. Fernie

"A large-scale expansion to Pacific Coast Bulk Terminals Ltd. has now been completed and placed in operation. The original plant, built approximately eight years ago, consists of the direct rail-car to ship transfer of bulk commodities. The extension includes additional rail-car unloading, a transfer house system for directing commodities to storage or ship, major storage and reclaim facilities, a second shiploader and a second deep-sea berth. In addition to the facilities for overseas shipments, a wood-chip loader and a barge berth have been installed for domestic shipments of wood chips and, occasionally, for other local commodities. The design considerations imposed by the nature of the products to be handled are covered in this paper."

Jan 1, 1969

By Robert H. King

An analysis of low-voltage shielded trailing cables is performed to develop a method for calculating the differences in operating costs between shielded and non-shielded cables. Two types of shield constructions are considered (SH-C and SH-D) for the three major underground coal mining methods. Data from laboratory and in-mine testing are presented in addition to an analysis of safety benefits. Recommendations for further investigations are proposed. Example calculations with sensitivity analyses are presented. Recommendations for further investigation include costs impact considerations.

Jan 1, 1980

By Robert G. Clarke

The production of natural abrasives varied in quantity and value compared with those of 1974. Output of tripoli-type materials and garnet both decreased in quantity and value. Special silica stone products decreased in quantity but in-creased in value. The production of emery increased 38% in quantity. The production of manufactured abrasive materials decreased for all types and the decreases were more in quantity than in value. [ ] FOREIGN TRADE Imports of abrasive materials were 15% less in value than in 1974, and exports plus reexports decreased in value 10%. Net exports, the excess of exports and reexports over imports, were $9.3 million, about four times that of 1974. The volume of all abrasive materials exported decreased and the value of nearly all decreased.

Jan 1, 1977

By S. G. Britton

"Strategies to improve performance in mining production, maintenance and mineral processing operations have evolved over time from straightforward time studies of individual machine performance in the 1960s-1970s to more sophisticated and better focused statistical and financial tools that have emerged in the 1980s-1990s. These newer strategies fall under the broad descriptive category of operational excellence.Operational excellence is the term that embodies a number of performance evaluating strategies, the most popular and relevant to mining include the following:• Six sigma for addressing errors within mining or milling process and work standards.• Lean manufacturing to optimize organizational and operational performance through continuous improvement.There are other strategies that can be applied as well and this paper is not focused on a review of the pros and cons of any one strategy. However, the common threads in these strategies embody the expectation that expected results from these efforts can be quantified and that value will positively benefit the targeted work process, organizational unit, equipment deployment or time schedule when applied to it as part of continuous improvement efforts.The priority for proceeding with any one or more of these efforts is based on the calculated net value of the required resources to make the change versus the estimated value gained. The practice is identified as the value mapping process.This discussion summarizes the value mapping process methodology used at a mature uranium mine and mill in northern Canada to work through the myriad of potential improvement efforts available through the operational excellence process for continuous improvement."

Nov 1, 2016

By David R. Jessey

This volume contains the detailed mine site reports written by the WAPORA, Inc. and KETRON, Inc. staffs. It is a companion Appendix Volume to Control of Water Pollution from Surface Mining Operations. Copies of this report are maintained on Open File at the U.S. Bureau of Mines Research Center, Spokane, Washington.

Jan 1, 1981

By R. F. Zaffarano

Data presented on the physical characteristics of the reservoir oil, Aneth field, represent the initial phase of a study of Paradox basin reservoir oils being made by petroleum engineers of the Federal Bureau of Mines, Petroleum Research Center, Laramie, Wyo. The purpose of the study is to determine the original reservoir-oil characteristics in several important new discoveries in the Paradox Basin and to investigate correlations between the properties of these reservoir oils and structural or areal position within the basin, If migration is limited and oil accumulates near its source, then it seems probable that few differences should be found in the composition and characteristics of reservoir oils occurring in given age rocks and within the confines of a geological basin. Within these limits, conditions that effected the formation of oil and its transfer from parent to storage rocks probably were rather uniform in an area the size of most of our geological basins. However, if oils should migrate considerable distances, it seems logical to expect that the relative quantities of gas and liquid components may differ in traps occurring along the direction of migration, corresponding with the theory of differential entrapment (5).4/

Jan 1, 1959

A maximum acceptable level of 2 mg/m3 of respirable coal mine dust in active mine workings was established, effective January 1, 1973, under the Federal Coal Mine Health and Safety Act of 1969. It is generally agreed that, as a result, coal mines in the United States are significantly less dusty than they were a decade ago. For example, operators of underground mining machines were exposed to between 3.9 and 6.5 mg/m3 of respirable coal mine dust during 1968-69; now they are exposed to between 1.3 and 1.8 mg/m3. Also, the incidence of underground sections cited for exceeding acceptable levels of respirable coal mine dust decreased during 1976-78, and the vast majority of all working sections are now in compliance. This improvement is very substantial by world standards. It must be regarded as a creditable accomplishment by the coal mine operators, federal agencies, and mine workers involved. Most of the improvement has been brought about by the use of existing technology to control, suppress, and collect respirable coal mine dust. Research and development by the Bureau of Mines has contributed significantly to the accomplishment by improving the methods for sampling, control, suppression, and collection.

Jan 1, 1980

By Robert Bottge

When a company develops a mineral property in a remote area of Alaska, it must consider how best to house its personnel. This Bureau of Mines report examines the economics of two options: company towns and company camps. The price required to maintain a 15% discounted-cash-flow rate of return (DCFROR) was derived for hypothetical 1,000-st/d cut-and-fill mines and 50,000-st/d open-pit mines located in three different regions of the State, One set of hypothetical mines utilizes a townsite; the other utilizes a relatively new concept, a fly-in camp or commuting operation, in which two shifts of employees operate the mine and all associated facilities for 1 week before being replaced by a second crew. The study shows that operating costs were higher for mines employing the commuting option than for mines having a company town because of the additional wages paid for overtime hours; however, the price required to obtain a 15% DCFROR for the single-product copper concentrate, f.0.b. the mill site, was significantly lower owing to the lower investment costs for the camp-type operation. The economic advantage for those mines utilizing the camp increases from south to north and from the coast toward the interior.

Jan 1, 1986

During the period January 1, 1977 through July 31, 1977, 5 percent (264,000 tons) of U.S. capacity was closed due to power curtailments in the Pacific Northwest because of the shortage of water. During July, one plant in Tennessee cut production by 50,000 tons annually due to a power reduction by the Tennessee Valley Authority. Full capacity production was resumed at a West Virginia smelter during September. If demand for aluminum is strong it seems likely that aluminum supply during the remainder of 1977 and in 1978 will be tight. The price was increased 3¢ per pound to 51¢ per pound effective March 28, 1977, and by an additional 2¢ per pound to 53¢ per pound, effective July 5, 1977. New projects and expansion of existing facilities are planned by Australian aluminum companies over the next 2 to 3 years. The companies listed have committed themselves to spending approximately A$801 million: Alcoa of Australia Ltd. -New alumina plant at Wagerup, south of Perth. Darling Ranges bauxite is located near the proposed project. A$650 million. Coma 1 co Industries Pty. Ltd. -Increase bauxite mining capacity and upgrade or replace other facilities at its Weipa mines on Cape York Peninsula region of Northern Queensland. A$81 million. Alcan Australia Ltd. -Expansion program that will increase capacity of the Kurri Kurri aluminum smelter north of Sydney about 50 percent, and improvement of other facilities at the plant. A$70 million.

Jan 1, 1977