Search Documents

By W. M. Scheding

"There has recently been a resurgence of interest in unit flotation of mill discharges. At the Kidd Creek concentrator, this technique has been successfully applied to silver flotation in a 3050 mtpd silver-copper-lead-zinc division. The major incentive has been improved silver payment through increased overall recovery and better distribution between the sequential copper, lead and zinc concentrates. A large, but variable fraction of the silver in the ore is present as native silver and, being dense and malleable, is susceptible to overgrinding. Grinding circuit surveys showed high concentrations of silver in both primary and secondary circulating loads. Laboratory testwork confirmed that this was selectively flotable, identified the secondary ball mill discharge as the best feed stream and optimized flotation conditions. A 10 t/h pilot plant campaign confirmed that the rate of accumulation of silver was sufficient to sustain continuous production of a silver concentrate and that flotation of the whole stream was not necessary.The present 30 t/h production circuit recovers from 5 to 50% of the silver in the ore at a concentration ratio between 25 and 250. The circuit also contributes to a better understanding of ore mineralogy, as an 'on-line' indicator of elemental silver content."

Jan 1, 1985

By C. M. WEILD

ATTENTION has been turned recently to the exploration and development of certain large blanket-deposits of brown iron-ore in Cuba. The most conspicuous of these to-day, and the one upon which the most light has been shed, is the Mayari deposit, situated about 15 miles south of Nipe bay. Here the Spanish-American Co. has sole control over 18,500 acres of ore-bearing lands, reported by its engineers to contain 500,000,000 tons of ore; and the necessary plant and equipment, with docks and railways, is now under construction for the early marketing of this ore. A similar deposit, and undoubtedly the next to be exploited, is the ore-field at Moa bay, where 13,000 to 15,000 acres of ore-lands, immediately adjacent to the shores of an excellent harbor, have been generously covered by numerous mining-claims, practically all controlled by four large interests. This deposit is now estimated to contain approximately 350,000,000 tons, on the basis of dried ore ready for shipment, a figure which may be increased when the western limits of the ore-deposit have been more accurately defined. Other deposits of the same type, but smaller and less accessible, are those at Cubitas, situated from 12 to 15 miles north of Camaguey city, and at Taco bay and Navas, points lying a few miles west of Baracoa. The area of the Cubitas deposit is said to be 6,000 acres, and the yield of ore is estimated at 150,000,000 tons. The Baracoa. deposits are less well known, but preliminary estimates have placed their joint ore-reserves at 40,000,000 tons. Accepting the above tonnages as reasonably correct, we conclude that the deposits enumerated give promise of adding about 1,000,000,000 tons of iron-ore to the world's supply; they have, therefore, to be considered in any attempt to fore-

Aug 1, 1909

"To prevent the propagation of mine explosions, the Bureau of Mines recommends:1. That all coal and lignite mines, except anthracite mines shall be rock dusted.2. That rock dust shall be distributed upon top, bottom, and sides of all underground openings of every description, to within. at least 4o feet of all working faces and the areas not rock dusted shall be kept wet.3. That the rock dust shall be maintained in, such quantity that the incombustible material in representative samples of dust collected shall not be less than 65 percent. Where methane gas is present in the ventilating current, the minimum percentage of incombustible matter in the mine dust shall be increased 1 percent for each 0.1 percent of methane.4. That when the rock dust in any area becomes caked so thatit cannot be dispersed readily as a cloud in the air, that part of the mine shall be redusted immediately.5. That the dust to be used shall not contain more than 5 percent of combustible matter nor. more than 25 percent of quartz or free silica; all of the dust shall pass through a sieve having 20 meshes per linear inch and 60 percent or more shall pass through a sieve having 200 meshes per linear inch; the dust shall not absorb moisture from the air to such an extent as to cake and destroy its effectiveness as a dry dust.6. That rock-dust barriers shall not be regarded as a substitute for generalized rock dusting.Research and experience have shown that maintenance of an adequate percentage of rock dust in all underground openings, whether gassy or not, of bituminous and subbituminous coal and lignite mines (anthracite dust does not propagate explosions) is the best means of preventing coal dust explosions. In rare instances where all fine coal particles on the floor, ribs, roof, and timbers are in a muddy condition continuously rock dusting is unnecessary.The term ""underground openings"" refers to all unsealed openings whether they contain track or not, and includes rooms, entries, crosscuts, breakthroughs, rock tunnels, slopes, haulageways, airways, and travelingways. The sealing of unused or abandoned parts of a mine in accordance with Mine Safety Board Decision avoids the necessity of rock-dusting the sealed-off openings.The kind of rock dust to be used should have the approval of the State Mine Inspection Service. Pure limestone or pare dolomite produces the best rock dust, as these dusts have low silica content, little tendency to cake, and a light color that aids illumination. To reduce tendency to cake it is preferable that not more than 75 percent of the dust pass the 200-mesh sieve. All sieve sizes are those of the Tyler screen scale. If the mine personnel is repeatedly exposed to breathing high concentrations of the dust, the percentage of free and combined silica should be as low as possible, preferably less than 5 percent. Persons engaged in the application of rock dust should wear approved dust respirators as listed in Bureau of Mines Information Circular 7030 or revisions thereof."

Mar 1, 1940

By Ashish Ranjan Kumar, Barbara Arnold, Luis Sanchez Gonzalez

The health and safety of miners is critical in the industry. Prolonged exposure to dust-laden air results in irreversible ailments like pneumoconiosis that have a severe impact on their lives. Operations use various personal protective devices (PPEs) to alleviate their exposure to respirable dust. Powered Air Purifying Respirator (PAPR) is one such device that uses high- efficiency filters and positive pressure masks to shield miners from airborne contaminants. Used in the medical and other industries, these respirators efficiently protected healthcare workers during the COVID-19 pandemic. Recently, the mining industry has shown a growing interest in adopting this PPE to ensure safe working conditions for the miners. We present an introduction to the PAPRs and discuss their dust capture efficacy in this manuscript.

Feb 1, 2025

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coal; (2) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making; and (3) to upgrade marginal coals through effective preparation. This is the second7j of a series of reports giving the results of studies by counties under part (1) of the investigation. This report covers Indiana County, Pa., which comprises parts of the Smicksburg, Punxsutawney, Elders Ridge, Indiana, Barnesboro, Latrobe, New Florence, and Johnstown Quadrangles. (See fig. 1.) A base map for each bed in each Quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds 0 to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1950

By D. E. Sullivan

The Minerals Availability Program of the Bureau of Mines conducts cost evaluations of current and potential mineral operations in the United States and foreign countries. The International Mining Cost Indexation System (IMCI) allows data of different time periods within a country to be updated to a common base year for analytical purposes. The IMCI comprises 12 factor cost indexes and an exchange rate series for 96 market economy countries, denominated in both local and U.S. currency. The IMCI for each country contains 12 time series indexes that measure the average annual rate of change in the cost of factor inputs to the mining industry within that country. Mining industry factor cost indexes include wages, plant and equipment, construction and mining materials, power and transportation, and other measures considered to comprise the majority of capital and operating costs. Cost data or proxies are collected in local currency. Index series within each country are constructed separately and indexed on a 1975 base year. The local currency index is converted to a U.S.-dollar-based currency index using an exchange ratio.

Jan 1, 1987

By T. Bajpayee, J. Ellenberger

Microseismic monitoring and evaluation is one aspect of the National Institute for Occupational Safety and Health (NIOSH) research program. Roof falls are often preceded by a period of elevated microseismic activity, but not all periods of elevated activity result in a roof fall, nor do all roof falls occur after some amount of elevated activity. The objective of this study is to review periods of elevated microseismic activity and determine whether fracture activity rate can be used to anticipate the initiation of roof falls. The study was carried out at an underground limestone mine where major roof falls are associated with excessive horizontal stress. The progression of roof falls was detected by the microseismic signature produced by the rock falling from the mine roof onto the mine floor, which is termed a roof fall impact event. A total of nine elevated fracture activity periods that resulted in seven major roof falls were examined. It was observed that elevated fracture activity preceded the initial roof fall impact event in three out of four major roof falls. The initial impact event was not identified for the remaining three roof falls. Fracture event rates were analyzed and a roof fall alarm trigger of five fracture events in a ten minute time period was established for this test case. The fall alarm trigger was tested against six of the elevated activity periods. Four roof falls occurred in the six periods of elevated activity, and two would have triggered the alarm before the roof fall occurred, while two false alarms were generated. The results show that limited success would have been achieved by the microseismic system as a roof fall alarm trigger. However, the trigger would have been successful at warning of the onset of elevated activity, allowing mine employees to respond appropriately. The study highlighted some issues with implementing such a system in an operating mine, including the need for real time identification of fracture related microseismic signals among mining induced signals, and accurate location and identification of fracture clustering.

By Antal Partos

ATLAS Processing Company Shrevesport, LA initiated a major plant expansion in 1980. SITE Engineers, Inc. provided engineering consultation regarding the foundation of the vacuum unit. Four test borings were drilled and laboratory testing completed for shear strength and compressibility. Vertical drains were proposed to accelerate time rates of settlements. Steel erection was completed by May 22, 1981 with very small < 0.1 in., settlements. Hydrotesting was initiated on July 9, 1981 and completed on August 27, 1981. An average rebound of 0.3 in. was computed resulting into an average net settlement of 0.5 in. This paper describes in detail soil behavior during load testing.

Jan 1, 1992

By C. Brown, N. Rayyan, T. H. Dubaniewicz

Lithium-Ion batteries (LIBs) have the potential to go into thermal runaway which introduces a new ignition source in hazardous environments such as gassy underground mines that may contain methane in the surrounding air. Researchers from the National Institute for Occupational Safety and Health (NIOSH) used an accelerating rate calorimeter (ARC) to induce thermal runaway in individual lithium-titanium-oxide (LTO) and lithium-nickel-cobalt-aluminum-oxide (NCA) LIB cells within a sealed enclosure with either no methane, a lean, a stoichiometric, or a rich methane-air mixture in the surrounding canister to determine if these LIB types would ignite the methane, causing an additive effect on overpressures. Canister pressures and maximum temperatures reached by the cells, surrounding air, and exhausted gases were measured in this study and remained consistent with varying methane concentrations.

Feb 1, 2023

By Pedro Hugo Tumialán de la Cruz

Dado que el Perú es uno de los países que cuenta con muchos recursos de yacimientos polimetálicos, el presente texto señala los aspectos que comprenden su metalogenia. Dentro de la mineralización de polimetálicos tenemos los siguientes tipos de yacimientos: aquellos relacionados con inyección magmática de composición intermedia a félsica y a la posible inyección de magma ultrabásico, pórfidos de cobre-oro-molibdeno y de cobre-molibdeno, yacimientos de molibdeno, tipo skarn,de reemplazamiento y relleno en caliza, de diseminación de oro de grano muy fino en caliza tipo Carlín, de oro y plata en areniscas-cuarcitas-pizarras, los cordilleranos, de tungsteno, de estaño en intrusivo félsico, volcánicos continentales como los yacimientos filonianos epitermales de plata-oro, los diseminados de oro y plata de baja ley y alta sulfuración, de antimonio, diseminados de oro-plata en intrusivos de composición intermedia, los volcanogénicos marinos de sulfuros masivos tipo Kuroco, tipo Missippi Valley y los lavaderos de oro.Se considerancomo épocas metalogenéticas de estos yacimientos polimetálicos edades de mineralización del Pérmico, Cretáceo Medio, Cretáceo Superior, Paleógeno, Neógeno, Cuaternario.

Jan 1, 2014

By E. A. Domínguez

La Espingarda kaolin deposit was formed by ?in situ? alteration of volcaniclastic rhyolitic rocks belonging to Jurassic Marifil Formation. Three volcanic lithofacies were identified: porphyric biotitic ignimbrites (PBI), a coarse lithic ignimbrite (ILG), a fluidal intrusive rhyolite (RFI), all kaolinized in different degrees. The alteration covers an ellipsoidal area of ~20,000 m2, with its alteration decreasing downwards and disappearing at 8-12 m from the surface. The length to thickness ratio of alteration is 60:1. An erratic silicification was found as small zones (<3 m2) of quartz stockwork. The mineralogy is kaolinite + quartz + feldspars + Fe-oxyhydroxides ± halloysite ± illite and interstratified I/S, although the relative proportions change in each rock type. Due to coarse grain size and high quartz content, natural kaolin is unsuitable for slip cast ceramics, unless beneficiated. Washed ILG kaolin has the best rheological properties and behavior in casting and drying for its mineralogy, particle size distribution, thin texture and surface activity, as well as a certain fusibility and firing kinetics. PBI and RFI kaolins, due to finer texture, smaller grain size, lower surface activity, and higher halloysite amount, have worse slip viscosity and thixotropy that are due also to soluble salts. For the same reason, they have good casting and drying properties, but their purity brings about higher softening temperatures and water absorption. Several parameters are used to discriminate between hypogene or supergene kaolinite genesis. The hydrothermal genesis is mainly sustained by fluid inclusion temperature (150-180ºC) in quartz veinlets, while weathering is supported by deposit morphology, simple mineralogy, kaolinite stable isotopes (d18O ? 18, 13; dD ? ?59; ?85) and paleoclimatic record. It is concluded that a weathering process formed the main alteration with some participation of steam-heated meteoric waters. Neither the contents of Au, Ag, As, Sb, Hg, nor drill data support the existence of any epithermal gold mineralization at the kaolinite bottom.

Jan 1, 2010

The Kiirunavaara apatite-magnetite orebody is about 4 km long and approximately 100 m thick sheet-like body, which lies roughly in a north-south direction and dips from the horizontal plane along its entire length, in towards the town of Kiruna. The origin of this orebody has been a matter of controversy, with both magmatic and hydrothermal origins proposed. Traditionally and for practical purposes this rich apatite-magnetite ore has been divided into two main types: low phosphorous ore (B-ore) and high phosphorous ore (D-ore). Further the low phosphorous ore is divided into the low alkali (B1) and the high alkali (B2) ore.

Jan 1, 2006

By Ronald C. Severson

Crystals of native gold occur in placer-type deposits. Gold, as a pure metal, is the most malleable metal known; therefore, delicate gold crystal forms should not survive mechanical transport and concentration processes involved in placer formation. To test the hypothesis that the crystalline gold is currently forming in place, two active gold-placer operations and an unmineralized background area in Alaska were examined. At these sites, rock outcrops, soil profiles, and native vegetation were sampled. At one sampling site, the soil was panned and yielded crystalline gold, as well as the more common rounded nuggets. The plants and soils were analyzed for their major, minor, and trace-element contents, especially gold. Two procedures, one a simple demineralized water leach and the other a partial digestion with acetic acid and hydrogen peroxide, were also used to extract gold and various anions from soils. The water-extractable gold ranged from <0.02 to 15.0 ppb Au in the extracting solution. This represents as much as a 104 enrichment in gold over average river water. This extractable gold is probably available to the native vegetation. Gold concentrations in the unashed dry plants from the two placer sites ranged between 0.4 and 106 ppb compared to a background range of <1 to <4 ppb Au. The presence of dissolved organic matter in the soils is thought to be responsible for the dissolution, transportation, and precipitation of gold in these placer soils, and this process is presently active in these soil profiles.

Jan 1, 2013

By John D. Galloway

Mining is one of the important primary industries of Canada, with a gross production in 1927 estimated at $241,773,000- the highest in the history of the country-and an impressive dividend record. It is quite apparent, therefore, that mining is a business worthy of the careful attention of the people of Canada. Furthermore, with a vast undeveloped territory more or less mineralized, it is highly probable that our mining industry will continue to expand indefinitely, with a consequent increase in production and in the amounts of the yearly profits distributed. In recent years, the public has taken a larger interest than formerly in mining-an interest, moreover, that is not academic, but primarily from the viewpoint of profits. It is quite evident that mining is a profitable business, at least to some, and the average man on the street, hearing of these profits, is attracted thereto. I have no doubt that many of you have .read in promotion prospectuses, with figures to prove it, that mining is the most conservative, the safest, and the highest-yielding business in the world. Now, a lot of this information is best judged by the old saying that "While figures don&apos;t lie, liars figure". At the same time, mining, properly conducted, is a profitable business, even though speculative, and undoubtedly much profit will come from Canadian mines in the future. In this paper my conclusions regarding mining investments are based largely on British Columbia experience, together with some slight knowledge of mining conditions in the other Provinces. It is considered, however, that the inferences drawn are applicable to mining throughout Canada.

Jan 1, 1928

By Alessandro Francelino Nogueira

A utilização de lasers de pulsos ultracurtos é uma alternativa para a realização de microusinagem em superfícies de metais, com aplicações diversas em inúmeros segmentos industriais, além das áreas aeronáutica, aeroespacial e naval, onde há crescente preocupação com a eletrônica embarcada. Neste trabalho foram realizadas microusinagens em superfícies de titânio utilizando laser de pulsos ultracurtos de femtossegundos. Tal processo resultou em mínima transferência de calor para o material, evitando assim e deformação superficial da chapa de titânio e a formação de material ressolidificado na região ablacionada, que são inconvenientes presentes na utilização do laser chaveado de pulsos longos da ordem de nanossegundos. Foram executados três tipos de microusinagens, com variações nas distâncias entre as linhas usinadas. Foi verificado ainda que a molhabilidade aumenta quando há o aumento da distância entre linhas usinadas. Finalmente, para a alteração da superfície com uma ínfima remoção de material, constatou-se que a utilização de lasers de pulsos ultracurtos proporcionam grandes benefícios para a integridade do material ablacionado.

Oct 30, 2017

By R. S. Dean

Boron compounds have been considered for many years as possible additions to iron and steel. A very recent use of boron-steel rods was for the control of neutron intensity in the graphite-uranium pile at the Clinton plutonium plant(130).4/ Norris(129) reports that slags containing boric oxide reduce the ferrous oxide content of steels and thereby the aluminum required for deoxidation. Boron is not considered an alloying element, but minute amounts produce what is often called a "needled" steel. The study of a series of iron-boron alloys by convenient steps, starting with iron containing no boron, indicated that boron was a hardening agent and made the iron very difficult if not impossible to forge. Then came the discovery that very minute traces of boron are quite different from the smallest amount previously thought worthy of study.

Jan 1, 1946

By Keros Cartwright

Sanitary landfilling has become one of the most widely used methods of disposing of solid refuse. A principal concern of regulatory agencies and the public itself is that landfill operations do not degrade the physical environment, including water resources, and the ground-water reservoir in particular. Ground-water and engineering geology can guide landfill operations into suitable terranes or develop measures to compensate for any natural limitations at a particular site Experience and research in Illinois suggest four activities relating to landfill disposal that warrant attention by geologists and engineers: (1) Regional delineation of favorable and unfavorable hydrogeologic conditions to facilitate planning and preliminary screening of potential landfill sites. (2) Site evaluations, with considerations of geologic materials, topography, water levels, flow systems, and local occurrence and use of water resources. (3) Re- search on aspects of the hydrogeologic environment that control effects of, or are modified by, landfills. (4) Formulation of practices in the siting, construction, and operation of landfills that prevent, mitigate, or isolate deleterious effects. The first two activities are basically in the domain of earth science, requiring the application of fundamental concepts of geology and hydrology and conventional site-exploration methods. The third activity, research, requires contributions from geology as well as other disciplines, including soil physics, sanitary engineering, and chemistry. The fourth calls for policy decisions by regulatory agencies and elected officials, using the contributions of scientists and engineers.

Jan 1, 1970

By H. Kenworthy

"INTRODUCTION ..Although the occurrence of iron ore in Missouri was recognized by Marquette as early as 1673, the first known mining and smelting operation was conducted in 1815. This operation was near Arcadia, Iron County, the first of its kind west of the Mississippi-Ohio River system. Several small furnaces of short life were erected in Missouri in the ensuing 30 years. However, until the extensive deposits of Iron Mountain and Pilot Knob were opened between 1843 and 1850, the state remained a minor producer of iron. It was this district which was chiefly responsible for the prominent position Missouri held in the iron industry until the late 1880's. At this time the easily minable high-grade ores became exhausted and the discovery of the immense Lake Superior deposits depressed the raw-ore price to such an extent that any mines ceased to operate. 3/Small yearly production of iron ores continued in Missouri to the present. Owing to war demands for hard ore suitable for open-hearth steel, the M. A. Hanna Co., through its subsidiary, the Ozark Ore Co., reopened the Iron Mountain, deposits and installed new equipment in an old concentrator to handle the low-grade ores left from previous operations. At present, ore production is from open pits, but underground mining is contemplated in the future. About 2,000 tons a day of iron ore is treated by gravity concentration of material from the open pits in the immediate vicinity. The concentrate is shipped to the Birmingham, Ala., district and to Granite City, Ill., for smelting. The coarse tailing is sold for ballast and concrete aggregate. The iron requirements of the concentrate stipulated by the purchaser are not difficult to meet, but the phosphorus is frequently higher than desired. For 1946 the concentrates averaged 54.18 percent iron and 0.235 percent phosphorus with low sulfur. The Ozark Ore Co. concentrate, however, sometimes contains as much as 0.40 percent phosphorus. The phosphorus in ores from those portions of the deposits wherein the phosphorus occurs with siliceous gangue is readily rejected in the milling, but in much of the ore the phosphorus is associated with the iron and concentrated with the iron minerals. Selective mining is impossible owing to the spotty occurrence of the phosphorus mineral. Often within 5 feet the ore will change from low phosphorus to high phosphorus, and it would be expedient to find a method of rejecting enough phosphorus at the mill from the latter type of ore to meet the phosphorus specification."

Feb 1, 1948

By William G. Kegel

Aside from having a usable product and good mining conditions, the greatest asset for a profitable coal mining organization is an effective mine maintenance program. The first step in acquiring this is the presence of good mechanics-men who have a desire to be mechanics and who want to know more about the design and control of the machines in their charge. The knowledge and ability to be found in a good mechanic is the result of ambition, curiosity, and determination. With these qualities as a start, the aspiring mechanic can launch his career if he begins learning all he can about mechanics, electricity, and hydraulics. The path is rough, but the goal is rewarding. Mining machinery probably absorbs as much or more abuse than any other heavy equipment in use today. And when one considers the conditions under which much of the repair work must be done, it can be seen that the mine operator needs the best of men and tools to perform the service. MOTORS AND POWER SUPPLY Mining machines, from their inception, have utilized the electric motor; and down through the years of mechanization, this power source has undergone many changes to better adapt it to the job. The first motors used were large, heavy-framed, open d-c motors (direct current), using a series or shunt winding. A motor having one or more field coils connected in series and themselves in series with the armature, is called a series motor (Fig. 1). The series motor had the advantage of quickly developing starting torque, and it was, and still is, the best motor for locomotive or shuttle car tramming service. The series motor, however, speeds up as the load is reduced and, if not properly controlled, can overspeed. The shunt motor, as its name implies, has one or more field coils in

Jan 1, 1973

By George M. Hamilton

The gas producer actually dates back far beyond the period from which we first find recorded data. A partial production of producer gas can take place in any type of solid fuel grate equipment, such as a boiler, or even a fireplace if a sufficiently deep fuel bed is provided. Those of us who have watched a coal fire burning in the hearth, have no doubt noticed at times, the gases liberated by the heat burning on or near the surface of the fuel bed. So far as we know, the first gas producer was built by Bischof in Germany in 1839, followed by Ebelman in France in 1840, and Ekman of Sweden in 1845. The first large industrial development in the use of gas producers was When the two Siemens brothers of Germany patented their first combined gas producer and regenerative furnace in 1861, thus opening up the field for the use of raw, crude producer gas in heavy furnace work. In the years 1879-1881 J, E, Dowson, of England developed a producer gas cooling and cleaning plant, which extended the scope of application of producer gas to make possible its use in small furnaces and gas engines.

Jan 1, 1961