Search Documents

By G. G. Goble

Dynamic pile testing is now over 20 years old as a routinely applied tool for evaluating driven pile installation. The first test on a cast-in-place pile was performed more that 15 years ago. The research that produced the method began almost 30 years ago. But, questions still arise regarding the appropriate use of this technique so some review is useful. Today a number of methods including dynamic testing all depending in some way on the application of dynamics are in routine use. First, Wave Equation analysis can be used to predict pile driveability before going to the field. The same approach can be used during driving to estimate the bearing capacity based on the blow count observed in the field. Dynamic measurements, on the other hand, can only be used after pile driving has begun. They offer predictions of pile capacity as well as measurements of hammer, driving system, and pile driving performance characteristics. The first part of this paper will be devoted to discussing how the foundation engineer can use these tools. First, a brief review of what dynamic methods actually do. In Wave Equation analysis a numerical model of the hammer, driving system, pile, and the soil is created by the engineer. The hammer is dropped on the pile and using a discrete, dynamic analysis the motion of the individual pile elements is calculated as a function of time. Of course, input information must be supplied by the program user to describe the hammer, driving system, pile, and soil. In the current state of development, the primary problem in input data is with the hammer performance (efficiency) and the soil description. Research may be able to do a better job with the soil data, but hammer performance will always vary from hammer to hammer and is dependent on the affectiveness of the inspection process. Prior to beginning pile driving the Wave Equation analysis supplies the best available estimate of what will happen when driving begins. It gives an estimate of blow count during driving, driving stresses, both tension and compression in the pile, and for diesel hammers, stroke. The selection of the driving system can be checked with the results of Wave Equation analysis and modifications can be made if required. For example, if the blow count at the required capacity was deemed excessive by the contractor a larger hammer could be tried or if driving stresses were too high changes could be made in the cushion or the hammer selection could be modified. All of these modifications are possible with only the cost of a computer run. The primary questions regarding the accuracy and reliability of Wave Equation analysis at this time is with regard to the assumptions made to represent the soil characteristics and the difficulty in predicting hammer performance.

Jan 1, 1993

Jan 1, 1879

By Günter Petzow, Hans Leo Lukas, Hans Jürgen Seifert

"The CALPHAD method (CALculation of PHAse Diagrams) has been extensively developed in the last 25 years and became a useful tool in materials science. Thermodynamic descriptions for the functions of state of unary, binary and ternary phases are derived by the optimization of phase diagrams. These functions are stored in computerized thermochemical databases and can be combined to extrapolate to multi component systems. Depending on special demand, the actually most advantagous presentations of the calculated results can be chosen: tables or in a clear graphical form as phase diagrams, phase amount diagrams or volatility diagrams. The method will be desribed by the system Ti-Si-C-N-O including the ceramic subsystem Si3N4-SiC-TiCi,N1_1,-C-N-O which is very important for the development of ceramic composites. The calculations give the thermodynamic stabilities of the condensed phases as function of temperature, concentration and partial pressure of different gas species. Adjusting the sintering conditions to these results the formation of unfavourable compounds or liquid phases can be suppressed.IntroductionThe CALculation of PHAse Diagrams (CALPHAD-method) of multicomponent systems provides the possibility to plan experiments very efficiently and avoid the experimental trial and error approach for the development of materials. The main problem for best use of calculated results is their interpretation with regard to the specific applications under consideration. Tables give the exact quantitative data for the treated phenomena. However, most important to make best use of these thermodynamic data is their graphical representation especially designed for the solution of specific problems, scientific as well as application oriented. Only well chosen graphical representations support a comprehensive understanding of the thermodynamic interrelationships and the transfer to the problem."

Jan 1, 1996

By Xing Yang, Zhen Peng, Guangwen Zhang, Haifeng Wang, Yaqun He

"Triboelectric separation of ilmenite ore based on the tribocharge differences between ilmenite and gangue minerals was conducted in this study. Triboelectric characteristics of ilmenite and its associated minerals were studied using polyvinyl chloride (PVC), pentatricopeptide repeats (PPR), copper, polymethyl methacrylate (PMMA), stainless steel (SS), teflon and quartz glass (QG) tribochargers in lab triboelectric unit. Results demonstrated that the ilmenite particles tribocharged positively while gangue minerals tribocharged negatively using PVC as tribocharger. The particle size also has a significant effect on tribocharge, and the -0.125+0.074 mm is the optimal size fraction of triboelectric separation. Charge-mass ratios of minerals increase with the increases of tribocharging length, but the increasing rate gradually reduce. At 1.5 m tribocharging length, charge-mass ratios of ilmenite, quartz, feldspar and mica are up to 6.07 nC/g, -6.05 nC/g, -4.30 nC/g and -4.56 nC/g, respectively. Based on the triboelectric characteristics of each mineral, triboelectric separation of ilmenite was conducted, and the grade of ilmenite ore increased from 15.47% to 28.40%. INTRODUCTION As a transition metal titanium plays an irreplaceable role in medical, aerospace and materials due to its light weight, high strength and corrosion resistance. Pure titanium dioxide is an excellent white pigment and is widely applied in industries of paint and textile. Ilmenite is the main raw material for titanium industry. For the beneficiation of ilmenite, series methods have been proposed, such as the application of dry magnetic and wet gravity separations to separate the ilmenite from the zircon and rutile. Electrostatic separation is extensively used in the beneficiation of heavy mineral sands for the recovery of rutile, zircon and ilmenite while flotation is used to separate fine ilmenite (Mehdilo et al., 2014; Fan et al., 2014). Compared with flotation and gravity separation, electrostatic separation does not consume water, and native properties of materials will not be changed and energy consumption will be reduced (Wang et al., 2014). Thus, the wide application of electrostatic separation and other dry separation methods is a trend in separation and purification industry, especially in water-scarce areas."

Jan 1, 2018

By D. L. Hollis

An arc plasma reactor, constructed and used for studying extractive metallurgical processing, was adapted by the U.S. Bureau of Mines to separate gases of different masses by using the high rate of plasma rotation. With argon and helium as input gases, peripheral reactor outlet ports had a measured average increase of about 10 pet in argon concentration relative to helium with the plasma on compared with plasma off for the same gas inlet concentrations in both cases. Approximately the same average increase in argon concentration occurred from the peripheral outlet port compared with a central outlet probe with the plasma on. There was no difference with the plasma off.

Jan 1, 2010

By H. L. Snyder

This paper outlines the approach to the underground construction work involved in the Churchill Falls Power Project. It is the first in a series of papers which CIM Bulletin plans to publish as the different 11hases of this large-scale operation evolve.

Jan 1, 1968

By Gabriela Pino, Maurício Torem, Diego Veneu

Because of its simplicity, economy and biocompatibility, research regarding the use of microorganism for decontaminating heavy metals produced by many industries is an area of growing interest. Also, there is a stringent need for the control of toxic metals produced during various production processes and released into the aqueous environment in order to avoid damage relevant to soil or groundwater contamination. Among the available treatment technologies, sorptive flotation has been considered as a promising alternative for the wastewater treatment. In the present study Streptomyces lunalinharesii strain was applied as bioreagent for the removal of copper, cadmium and zinc. The removal of those metal ions depends mainly on the respective pH value, influencing the aquatic speciation during the process, as well as the zeta potential of the system and biomass concentration. Langmuir and Freundlich isotherms have been depicted. Dispersed air flotation was applied as the subsequent separation method for harvesting the suspended metal laden microorganisms, following the biosorption of copper, zinc and cadmium. The investigated parameters (in batch mode, laboratory scale) were in this case the saturator pressure, the coagulant concentration and the recycled flow. Applying the optimum defined conditions, over 60% removal of metal ions have been achieved in one stage and simultaneously, quantitative separation of the used (metal-loaded) biomass has been obtained.

Jan 1, 2014

By Steven J. Kirk

In the past decade, many hardrock surface miners have revegetated dumps and tailings ponds to allow those waste disposal areas to blend more easily with the surrounding landscapes. Efforts have also been made to more creatively use the flat land resulting from the disposal of overburden and tailings. However, the mines which serve the best post-mining land uses are those that have been preplanned to incorporate such end uses. To more fully explore such a philosophy, interdisciplinary team from The University of Arizona conducted a study during 1974 and 1975 of six open pit copper mines in the Santa Cruz River Basin south of Tucson, Arizona for the purpose of investigating both interim and end-use possibilities for mine waste disposal areas. Among other reasons for the study, it was felt that alternatives for such waste areas would be more socially acceptable than barren dumps or tailings ponds. The team, known as the Mines Project Group, consisted of architects, engineers, and hydrologists. As it would have been economically infeasible to move the existing waste rock dumps or tailings ponds, preplanning was limited to the disposal of waste generated after the inception of the project. To better present their concepts, architecture professors Kenneth Clark and Fred Matter constructed a large-scale cardboard relief model of the mines and the surrounding Santa Cruz River Valley (1). The model was built at a scale of 1:12 000 (1 in = 1000 ft) with 30.48 m (100 ft) contour intervals and covered an area of 40.23 km by 32.18 km (25 miles by 20 miles) in scaled area. The mines being studied were cut into the model, but the proposed waste dumps and tailings ponds were built separately so different disposal configurations could be evaluated.

Jan 1, 1980

This volume constitutes the Survival Subsystem portion of the final report for the Coal Mine Rescue and Survival System (CMR&SS) program, which was conducted by the Westinghouse Electric Corporation under contract to the United States Bureau of Mines (Contract Number H0101262 dated June 17, 1970). The program was directed by the Special Systems Department of the Westinghouse Baltimore, Maryland, facility. The basic objectives of the CMR&SS program were to develop and test hardware to determine the efficacy of a variety of coal mine rescue and survival concepts and techniques. These concepts were drawn from two major sources: the Request for Proposal from the Bureau of Mines1 and the final report on the Mine Rescue and Survival Study conducted by the National Academy of Engineering2 (NAE).

Jan 1, 1971

By I Treloar, T Elenbaas, E Isaaks

Critical reviews of grade control generally focus on blasthole sampling and the estimation of ore control block model (OCM) grades, with little or no attention given to dig-line design. For example, the estimation of block grades is deemed important as estimation errors lead to the misclassification of ore types and subsequent dollar loss. Recognition of the problem that the underestimation of block grades may be more or less costly than overestimation led to the application of loss functions to the classification of individual OCM blocks by ore type. The method is known as maximum profit selection (MPS). However, each OCM block may be misclassified a second time by dig-line design. Although each block may initially be assigned an optimum ore type by MPS, OCM blocks are seldom individually mineable by ore type. As a result, a common solution to this problem is the design of mineable polygons or dig lines loosely constrained by a minimum mining width. All material within a properly designed dig-line polygon can be mined and sent to a single destination such as the mill, stockpile or waste dump. These dig lines are often designed manually or by simple variations of computer-generated contour lines. They are generally suboptimal and result in additional misclassifications of ore types. This paper provides an algorithm for constrained optimum dig-line design where dig-line misclassifications are also evaluated through loss functions or MPS. Constrained optimum dig-line designs minimise the dollars lost by dig line misclassifications for a given minimum mining width constraint. A case study is provided illustrating constrained optimum dig-line design and subsequent benefits.CITATION:Isaaks, E, Treloar, I and Elenbaas, T, 2014. Optimum dig lines for open pit grade control, in Proceedings Ninth International Mining Geology Conference 2014 , pp 425–432 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By J. Jirestig

Poor grade iron ore, suffering from interlocked particles, is challenging for any process technology. Extensive grinding is required to attain liberation and to yield concentrates of desired grade. Fine particles are commonly very difficult to retrieve, resulting in value losses to tailings. In this paper, results from HGMS tests on fine to ultra fine hematite are reported. Special emphasis is put on slurry flow velocity. If hydrodynamic drag force, i.e. flow velocity is not controlled and kept constant during the feed and/or rinse phase, fine particles will not be captured and retained. Flow velocity control and constant flow during separation are achieved by discharge valves/slots and parallel magnetic flux and pulp flow configuration. In tests, increased slurry velocity from 178 to 268mm/s caused Fe-recovery to drop from 78 to 48%. Proving that flow velocity control is essential to optimise grade and recovery. HGMS tests at the Metso mineral laboratory on natural (weathered) hematite fines clearly show a large potential to recover valuables, currently lost to tailings. Even at particle size distributions as low as D80=35µm concentrate grades and recovery are very satisfying. Two samples, in-plant desliming rejects (D80=35µm and 50µm) where significantly upgraded and recovered, from 45,3% to 63,6% and 53,0% to 63,4% Fe, at 73,8% and 81,1% Fe-recovery respectively. Other types of in plant rejects, such as gravity separation or WHIMS tailings, also benefits from HGMS separation. Gravity separation reject, 55,8% Fe, at D80=500µm was tested, yielding a magnetic concentrate of 60,8% Fe at 50,7% Fe-recovery. The results indicated that the hematite was poorly liberated. HGMS separation was repeated after a regrind to D80 150µm, resulting in a magnetic concentrate of 62,8% Fe at 75,9% Fe-recovery. The tests prove that hematite, presently lost to tailings streams, can be recovered by HGMS and thereby significantly contribute to improved overall economy. Keywords: HGMS, magnetic separation, recovery of ultra-fine hematite, Indian hematite ores, hematite recovery from tailings

Sep 1, 2012

By C. K. Leith

THE outstanding fact of the mineral world today, at home and abroad, is the surplus of current production, and particularly of capacity for production, over current requirements. This is not by Any means a new condition, but never before has it loomed up in such' menacing form. - Those of us who have devoted most of our professional efforts to the discovery and development of 'new mineral supplies now suddenly find ourselves with the job apparently accomplished, waiting for some one else to find an outlet for excess mineral production before we can further. The management of the industry is in much the same boat. The psjrcho16gy of the industry has been so grooved in the direction of acquisition of, minerals that at the present moment the mineral industry confronts the new problem of surplus in more or less of a daze.

Jan 1, 1931

By J. N. Hryn

This paper describes some of the work done in Phase 1 of a multi-year, five-phase program aimed at demonstrating the economic feasibility of producing commercial-scale quantities of commodity materials derived from salt cake residue-oxide. The amount of salt cake generated annually in the U. S. is estimated to be 510,000 tons, including 340,000 tons of residue-oxide. Used beverage can (UBC) processing accounts for the majority of residue-oxiae that could be made available for further processing into commercial products. To characterize the composition of residue-oxide. eight residue-oxide samples from various secondary processors were obtained and analyzed. Surprisingly, the composition of residue-oxide was found to be independent of source or alloy family being processed, with? the exception of slightly elevated silicon levels in 3XXand UBC residue-oxide samples. Major phases detected in the residue- oxide were? alumina, spinel, and aluminum hydroxides. Preliminary economic analyses indicated that the refractory market appears to be the best choice for high value-added products produced from residue-oxide with minimum processing. Bench-scale tests indicated that low silicon containing residue-oxide is ready to enter this market, but the elevated silicon content of UBC and 3XX residue-oxide preclude this possibility. A separation technology should 'be developed to remove silicon-containing . species from the alumina and spinel values Present in residue-oxide. This technology would then allow UBC and 3XX residue-oxides to be converted to significantly higher value-added products.

Jan 1, 1995

By J. L. Collins

"Une recherche debutee en 1987 tente de cerner divers éléments ayant un impact sur la productivite miniére, de facon à améliorer la planification des operations souterraines. II a été possible de recueillir jusqu'à trente variables dans sept opérations minières differentes du Nord-Ouest québécois. Cette présentation rend compte de quelques résultats préliminaires obtenus à l’une d'entre elle. Entre autres, elle montre comment une association entre une analyse de régression multiple et un logiciel d'optimisation (OPTIMUL) peut servir à une application particulière de la planification d'une opération minière du Québec. Plus spécifiquement, la présentation montre comment une quantité appropriée de ANFO et de TOVEX peut maximiser la quantilé de minerai cassé, minimiser les couts de sautage ou encore minimiser les coûts d'explosifs par tonne de roche cassée, en se basant sur une série de contraintes réalistes provenant de la mine.ABSTRACTA study, underway since 1987, tries to evaluate factors affecting mines' productivity. Information has been collected from seven underground mines in Quebec and this paper shows preliminary results from one. In particular, it shows how a combination of multiple regression analysis, mathematical programming and a set of realistic mine constraints can be used for a particular application of mine planning. More specifically, the paper shows a parallel between maximizing production of tons of broken are, minimizing explosives costs or minimizing the costs of explosives per ton of broken are by an appropriate selection of ANFO and TOVEX quantity of explosives. Finally, the paper shows that minimizing the costs of explosives per ton of broken are is the best alternative to follow providing a special optimization program can be set up."

Jan 1, 1990

By Alireza Golabchi

The AEC (Architecture, Engineering, Construction) industry is an information intensive industry and all related processes employed during different phases of a project, including planning, designing, building, manufacturing, occupying, and maintenance, involve vast amounts of data that is used for a wide variety of purposes. Building Information Modeling (BIM) is a powerful shared knowledge resource which stores this data to support decision making about a facility through all these different phases in its life cycle. Nowadays, BIM is mostly used in the design and construction phases while it can also be highly beneficial beyond those stages. For example, in the Operation and Maintenance (O&M) phase, BIM could be used for automated facilities management or robotic inspection to provide semantic knowledge for navigation. For any implementation not related to the original intent of the BIM (design), organizations need to be able to represent their project data in a common interpretable form, which provides the possibility of an accurate exchange of data among different software products and platforms, known as interoperability. This study has investigated the current state of interoperability between software products used as Building Information Modeling tools. The main focus has been on a popularly used format for BIM models, Industry Foundation Classes (IFC), since it has been specifically developed to enable standardized data exchange. The research methodology involved a comprehensive literature review and the gathering of all fragmented prior research related to the field in order to develop a consistent understanding of the current state of knowledge. This was accompanied with a detailed case study that evaluated and compared two dominant pieces of BIM software, Revit and Bentley, and examined their interoperability strengths and weaknesses while using the IFC format.

Aug 1, 2013

By J. F. T. Agapito

Stability in Exxon's Colony Pilot Mine in the Piceance Creek Basin, Colorado has been monitored by periodic pillar stress-determinations End roof-to-floor convergence measurements since 1971. Pillar failure has caused marginal stability in some areas of the mine. Measurements taken during the process of failure provided valuable information on the in-situ pillar strength and long-term behavior of the mine structure. Four pillars were reinforced by 32 mm (1-1/4 in) diameter tensioned grouted bolts to increase long-term stability in the northern area of the mine. Stability of this area is necessary because future plans envision its use as an exit/access and ventilation exhaust. Computer analyses were performed to help evaluate the effect of pillar reinforcement on long-term stability. Results indicate that bolting is particularly useful in stabilizing failed pillars, but its effects are significant only in the immediate area of the pillar. The projected significant decrease in deformation of two extensively failed pillars near a main entry indicates that bolting reinforcement will assist the long-term stability of the opening.

Jan 1, 1985

By K. H. J. Clarke

"ALTHOUGH nickel was not identified as a separate element until a Swedish scientist, Axel Frederick Cronstedt, did so in 17 51, its utilization dates from pre-historic times. From its humble beginnings nickel has grown in importance until, today, in our clocks, television sets, automobiles, and air-planes, in our bridges, tableware, farm implements, and the equipment which processes our food, it is constantly at our service.For convenience in assembly, data and information relative to The Marketing of Nickel will be outlined in five phases: (A) Sources, (B) Distribution, (C) Utilization, (D) Market Development, and (E) Conclusions."

Jan 1, 1960

The safety of mining operations is significantly influenced by the in situ stress fields in which the mining excavations are created. From the point of view of planning of mining operations, the in situ stress field is a most important input parameter for valid modelling of excavations. Many in situ stress measurements have been carried out for mining and civil engineering projects in southern Africa over the past 30 to 40 years. A database of in situ stress measurement results and observations has been compiled. This paper presents results extracted from the database which are considered to be of particular interest to mining areas in South Africa. The database will permit the estimation of likely stress conditions in new areas of mining, provide a basis for evaluation of results from future in situ stress measurement programmes, provide a basis for comparison of observed behaviour with expected behaviour, and provide a source of data on which realistic design and layout analyses can be based. The information contained in the database indicates that horizontal to vertical stress ratios in the Carletonville, Klerksdorp and Rustenburg areas are significantly higher than the value of 0,5which is commonly used in mine layout planning.

Jan 1, 1998

By S Van Duin, I Porter

This paper discusses how advanced manufacturing technology (AMT), which is fundamentally reliant on and developed via multi-disciplinary skills, has benefitted non-mining industries, and what lessons can be derived from this experience to benefit the mining industry, particularly underground coal mining. Examples of AMT use in æconventionalÆ industry, some drawn from the more than 25 years experience in many different industries of the Automation and Robotics team at the University of Wollongong, are described to show typical benefits, risks and opportunities expected in using AMT. Applying AMT to mining brings many unique challenges and this paper expands on these and then provides practical examples of how a multi-disciplinary team can develop new processes and systems leading to productivity, safety and other benefits for underground coal mining.

Sep 26, 2011

By Dobson C. L.

The memoir, presented at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne on 3rd June 1916, outlines the career of one of the Institute's oldest members and past-president 1896-1898, including the improvements he introduced at Harton, St. Hilda and Boldon collieries and his activities with the Institute and the Durham Coal Owners' Association

Dec 1, 1916