Search Documents

By Yun Li

In 1999 Yunnan Copper Corporation (YCC) decided to modernise their copper smelter and change the existing sinter plant I electric furnace process to a combination of ISASMEL T and electric slag cleaning furnace. The main aim of the project was to improve the environmental performance and decrease the energy consumption. Generally the project has been successful, partly attributable to the selection of a reliable and fully demonstrated technology. The design capacity for the ISASMELT furnace is 600,000 tonnes of dry copper concentrate per year. The furnace has been running smoothly since heat up in May 2002. YCC expended considerable effort in the preparation for plant operation. An extensive training program for key YCC personnel at the Mount Isa Copper Smelter improved their understanding of the process significantly and ensured successful hand-over of the technology. This paper describes the project history and summarizes initial operating results.

Jan 1, 2003

By Yun Li

In 1999 Yunnan Copper Corporation (YCC) decided to modernise their copper smelter and change the existing sinter plant I electric furnace process to a combination of ISASMEL T and electric slag cleaning furnace. The main aim of the project was to improve the environmental performance and decrease the energy consumption. Generally the project has been successful, partly attributable to the selection of a reliable and fully demonstrated technology. The design capacity for the ISASMEL T furnace is 600,000 tonnes of dry copper concentrate per year. The furnace has been running smoothly since heat up in May 2002. YCC expended considerable effort in the preparation for plant operation. An extensive training program for key YCC personnel at the Mount Isa Copper Smelter improved their understanding of the process significantly and ensured successful hand-over of the technology. This paper describes the project history and summarizes initial operating results.

Jan 1, 2003

By F. De Lucio

Para la aplicación de la instalación de un sistema de relleno hidráulico es necesario evaluar las funciones que el relleno debe contener y determinar si el material a usar cumpla con las funciones especificadas. En ese sentido, el objetivo del texto presenta una interpretación científica sobre tal método para especificar las funciones que el relleno deba cumplir y la metodología experimental adecuada que evalúe cuantitativamente a un relleno hidráulico.. Asimismo, se describen sus propiedades estructurales como la densidad relativa, reducción de volumen y estabilidad de tajeos contínuos, así como los métodos indirectos para inferir dichas propiedades y las posibles consecuencias secundarias que pueda generar el empleo de relleno hidráulico.

Nov 20, 1972

By S. H. Ash

NINE-TENTHS of the total anthracite deposits of North America are in Pennsylvania. Corrosion of pumping equipment by acid mine waters has been experienced at tremendous cost by mining companies in the anthracite region of Pennsylvania, for many years in many ways. The design and specifications of the large centrifugal pumps as provided in the proposed mine-drainage system (7-35, 45, 46, 48, 54, 64, 70, 71)° make it imperative that a metal or alloy be recommended that has the highest corrosion resistance and, at the same time, acceptable properties suitable for general workability (welding and machining). This report presents data on the corrosive and erosive effects of acid mine waters in the anthracite region on metals and alloys for pumping equipment and drainage facilities necessary to remove or control this water.

Jan 1, 1955

By Pathies Nawej Muteb, Tom Strombotne, Karl Leetmaa, Irma Gabric, Keith Darby

"Continuous control of the final grinding product size is important to optimize gold liberation for Gold Milling operations. At Meadowbank Mine an on-line Particle Size Monitor has been employed successfully to achieve the targeted final grind which leads to optimizing the gold recovery at maximum grinding circuit throughput. The live monitoring of the final product particle size leads to a maximum grinding circuit throughput every minute during the process. This paper discusses the optimal utilization of the Particle Size Monitor to assist the Mill operator to maximize the grinding circuit throughput as the milling conditions change due to variable ore processed at Meadowbank Mine. Also the paper includes the usage of the Particle Size Monitor to guarantee the final grind target at each instant of the process.IntroductionAgnico-Eagle is a Canadian-based company that Trades on the TSX & NYSE (AEM). It owns eight mines (8) operating in Nunavut, Quebec, Finland and Mexico and has more than 7,500 employees (Figure 1). 1.6 M ounces of gold were produced in 2015 and the annual average annual production from 2016 to 2018 is forecast to be approximately 1.53 million ounces of gold.The Meadowbank Mine is located in Nunavut, Canada (Figure 2). The mine opened in 2010 and from 2010 to 2014 a total of 1.8M oz of gold was produced. The milling rate is 4.2 Mt per year with an average mill throughput of 11,900 tpd or 496 tph. Average annual gold production over life of mine is expected to be 450,000 ounces. Meadowbank has 775 employees, of which 265 are Inuit or 36% of the total workforce. Estimated life of mine is 2010 to 2018. Gold production in 2015 was 381,804 oz. Meadowbank was Agnico-Eagle’s largest Gold producer in 2015."

Jan 1, 2017

By M Rafty, C Lane

Managing water is a key aspect of mining, whether a site is in water surplus or water deficit. Water in tailings storage facilities (TSFs) needs to be managed carefully to maximise the density of the solids, maximise the re-use of available water and to minimise the risk of water overtopping the spillway in the event of heavy rainfall. Developing a water balance models is a standard method for monitoring the major flows of water around a site. However, models created by specialist consultants are often overly complex and are not suited to being used by process plant personnel after they have been handed over to the mine operator. Models typically offer information on water management at the time that they are created, but then ‘sit on the shelf’ and offer no further insight or value for operating mines. Advisian has developed a customised water balance model for a mine in Sub-Saharan Africa, which can be adapted to other locations, to assist in managing water at the site and in particular to predict the current and future water level and volume in the TSF under various rainfall scenarios. The model was developed using Microsoft Excel and requires no specialist skills to operate. Site personnel enter in daily production, water transfer and rainfall data and then view the output dashboards to observe the current water level and volume, decant rates, licensed water abstraction and water supply versus demand. The output dashboards were developed in close consultation with the client to ensure that all of the relevant key performance indicators were included, from the perspectives of all the key stakeholders. This modelling approach focusses on the needs of the people who will actually use the model to actively manage TSFs with the need to involve the model developer as part of ongoing operations eliminated. The simplicity of this approach is now being embraced by other mine sites in Africa and Australia. CITATION:Rafty, M and Lane, C, 2018. Water balance management 101, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 485–490 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By A. B., Sabin

THERE are many who know The Lucky Tiger and will remember the 35-mile road from Esqueda, a station on The Nacozari Railroad in northern Sonora, Mexico. They will remember the box canyons of the Agua Caliente Mountains which are scarcely wide enough for two cars to pass; the Bavispe River which one hour may be a lazy trickle and the next a sweeping torrent, and the tortuous road up Tigre and Espuela canyons, now following the wash, now hugging some gigantic red cliff. It is still the same. From camp the view of the distant blue-gray mountains is the same. But one thing a visitor of a former day might miss: The hundreds of pack mules and burros, loaded with concentrates from the mill, which used to take most of the road and show up at the most inopportune places, have almost disappeared, replaced of course by the auto truck.

Jan 1, 1929

By W. Kint

More than 10 years ago, one of MECS?s current partners KVT developed the so called SULFOX process for cleaning waste gases containing sulfuric compounds. In this Wet Acid Process (WAP) compounds such as SO2 and H2S, CS2, COS are oxidized over catalyst bed(s) to SO3 and finally sulfuric acid is formed. The individual plants are designed according the feed gas concentrations and customers requirements to keep the investment and operating costs as low as possible. MECS strongly believes the technology we propose will meet all your expectations. Thanks to our vast experience in the construction of sulfuric acid plants (MECS built over 800 sulfuric acid plants worldwide) we were able to design you a very reliable installation. MECS is offering the metallurgical industry, besides our conventional acid plant technology (for strong SO2) and our DynaWave? scrubbing technology (for very low SO2), a SULFOX wet acid plant (for the mid range SO2 concentrations) including an optional upstream DynaWave gas cleaning plant if required. See the figure below. Besides providing advanced technology, MECS is the only company who designs and manufactures its own key critical equipment. We manufacture our own catalyst, mist eliminators, acid distributors and coolers. Because of our in-depth technology knowledge, we understand the critical aspects necessary for making optimum equipment designs. With this combined supply of technology and key critical equipment, we can make a single overall guarantee second to none other in the world.

Jan 1, 2009

By C. F. Starr

This paper deals with the various types of cable in use in mines, with special attention paid to their construction. There will be a few comments regarding the different insulants, jacketing materials and armouring used, depending on their application. Governing standards and the differences therein will also be discussed.

Jan 1, 1969

By Patrick D. McLaughlin, C Fordham

"The project outlined in the accompanying paper was to densify beach sands on the pond side ofa tailings dyke to the strength required for future dyke construction, This was to be achievedthrough the detonation of relatively small explosive charges in the sand to cause settlement intoa denser state."

Jan 1, 1992

By David E. Siskind

The Bureau of Mines recorded particle accelerations in the mine roof produced by three types of explosives in the Pilot Knob Pellet Co. mine, Pilot Knob, Mo. Examined were the effectiveness of cube root, square root, and two-thirds power scaling in grouping the underground blast vibration data, and the effects of mine geometry, rock type, explosive type, and charge size on blast vibration levels. A propagation law for this mine was determined. The scaling factor of the square root of the charge weight was developed from previous Bureau studies of vibrations from quarry blasts, and in under-ground blasting both square root and cube root scaling were found applicable for scaling particle vibration data. The vibrations from the Pilot Knob blasts were best grouped by a square-root scaling factor. The empirical propagation equation AW1/2 = 76,250 (R/W1/2)-2.61 where A is the peak acceleration in g's, W is the charge weight in pounds, and R is the distance from the blast in feet, may be used to describe vibration amplitudes from charges fired with zero delay caps or with a single cap at Pilot Knob. Statistically significant differences were found in the vibration levels generated by the different explosives. The Power Primer (75-percent weight-strength ammonia gelatin dynamite) produced levels of vibration of 1.7 to 2.4 times those of AN-FO and slurry explosives; the latter two are approximately equal.

Jan 1, 1973

By Constantine C. Popoff

"INTRODUCTION AND SUMMARYDuring 1946 several high-grade limestone deposits in western Washington were examined by the Bureau of Mines. This report presents the data obtained from investigation of the Sauk Mountain deposits in east-central Skagit County, Washington.The investigation consisted of transit and topcgraphic surveys and sampling. The areas selected for sampling were first cleaned by blasting; channel samples up to 40 pounds were cut where practical. Chip samples averaging 30 pounds were taken where channel samples could not be cut. A total of 21 samples in the Sauk Mountain area were taken and. analysed. The locations of the samples are shown in figures 2 and 4, and the analyses are listed in tables 1 and 2. This investigation is a part of a long-range program of general investigation of mineral resources for future industrial development of the Pacific Northwest. The Sauk Mountain deposits were investigated for the purpose of disclosing now sources of high-purity limestone, which could be mined and shipped at low cost to Seattle and other industrial cities in the Pacific Northwest."

Oct 1, 1948

By R. R. Wells

As a part of the strategic minerals program of the Bureau of Mines, nine chromite-ore samples were obtained during the period 1949-56 from mines in the vicinity of Red Mountain, near Seldovia, Kenai Peninsula, Alaska. This report summarizes the results of beneficiation studies of the samples at the Bureau's Juneau, Alaska, and Albany, Oreg., laboratories. In general, the ores were found amenable to concentration by gravity methods for producing concentrates that assayed over 48 percent chromic oxide. Intimate association of chromite and gangue minerals, however, necessitated fine grinding and limited the amount of chromite recoverable. Recovery of chromium in concentrate that assayed 48 percent chromic oxide or higher ranged from approximately 20 percent for low-grade ores (10 to 12 percent Cr203) to more than 95 percent for 1 high-grade sample (42 percent Cr203). The iron content of the chrome-bearing mineral -hence, the chrome/iron ratio of finished concentrate -appears to vary with the grade of the ore. Concentrates made from high-grade ores had chrome/iron ratios as high as 3.1:1; the concentrates from low-grade ores, however, had chrome/iron ratios as low as 1.8:1.

Jan 1, 1957

By R. P. Stahura

In many ways, conveyors are the lifeline of mining and processing operations. Like arteries in the human body, they continuously supply materials to and carry finished products and waste away from vital on-going operations. And like arteries, when the conveyors are running with less than maximum efficiency and productivity, it spells serious trouble for the operation's overall health. Inefficient conveyors suffer carryback, leading to the build-up of materials on idlers and other expensive components. They spill and leak material at loading zones and conveyor transfer points, causing accumulations that can damage the belt, wear moving components, and increase both clean-up labor and maintenance expense. They wander or mistrack, spilling material and endangering personnel and conveyor components including the belt itself. And through these inefficiencies, they multiply the operation's hidden costs. These added expenses are created in lost production, increased downtime for service and maintenance, and the cost of the replacement of prematurely worn equipment. In addition, the attitude that inefficiency is "good enough" is recognized elsewhere in the organization; as a result, other departments relax or operate at less than peak performance. Quality goes down and with it employee morale.

Jan 1, 1992

By Bradford C. Wesstrom

An overview of the challenges encountered at the Freeport McMoRan El Paso Copper Refinery with higher concentrations of antimony electrolyte will be shared. The observations will cover the detrimental effects on copper starting sheets, commercial cathodes and anode slimes. The study will show negative effects on quality and productivity. Experimental work will utilize a test cell to study the effects on electrolytes by different Antimony, Arsenic concentration and anode molar ratio. Best practices will be shared for producing high quality cathodes while effectively managing the detrimental effects of higher antimony electrolyte.

Jan 1, 2014

The general types of industrial behaviour of liberated valuable sulfide minerals in the 0 - 10 ¦m size fraction are described and tests to explore on site at a concentrator the general nature of any deficient behaviour are discussed. In addition, the general types of behaviour of the gangue minerals in this size fraction are also described in terms of their mechanisms for recovery. These behaviours are also discussed in terms of the type of grinding device and grinding environment in which they were produced and the target grinding product size. Major recent improvements in the industrial capabilities of grinding devices are discussed.Present difficulties in characterisation of particles in the 0 - 10 ¦m range are described and desirable improvements for the future are outlined. Further, desirable improvements for industrial processing of valuable minerals in this size range are discussed along with some remedial actions.

Jan 1, 2005

By S. Banisi, A. Ghasemi, E. Nematollahi

Discrete element method (DEM) has been used as a popular simulation method to verify designs by visualising how material will flow through complex equipment geometries. Although DEM simulation is a powerful design tool, finding a DEM model which includes real material properties (e.g., shape, cohesion and friction coefficients) is not computationally feasible. In order to obtain more realistic results, particle energy loss due to rolling friction has been highlighted by many researchers. To implement a reverse torque to account for rolling friction, various models have been proposed. On account of the complexity of the problem, there is no unique model for all applications (i.e. dynamic and pseudo-static regimes). In this paper, an in-house developed DEM software (KMPCDEM ©) was used to assess the robustness of three commonly used models by comparing the repose angle of iron ore pellets obtained through the draw down test in a laboratory setup and then the elastic–plastic spring dashpot model was modified based on considering the individual parameters instead of relative parameters of two contact entities. Results showed that the modified model could produce higher repose angle. The modified model was used to calibrate DEM simulation of repose angle of iron ore pellets in a laboratory setup of the draw down test. Comparison of the calibrated DEM simulation and laboratory results showed 2° differences between the predicted and measured angle of repose. This difference was attributed to considering the particle shape effects by assuming a spherical shape for particles. Keywords: DEM, rolling friction,particle shape, repose angle

Jan 1, 2020

By Anton Gronningsater

AS we know, Sir Henry Bessemer introduced Bessemer converting in the steel industry about 1855. It was not until twenty years later that the principles were adopted by non-ferrous metallurgists. In 1880, Manés first produced blister copper from matte in a converter, a very important forward step in copper metallurgy. For thirty years, up to about 1910, bessemerizing of copper matte was carried out in the acid-lined converter. It is not necessary here to enumerate all the shortcomings of that operation, one of which was that it strictly limited the grade of matte that could be treated; a 35 per cent matte was low in those days. From the early days of copper converting, many and repeated attempts were made to use a basic converter lining, and the older metallurgists will remember the numerous reports and discussions in connection with such experiments. These make interesting reading. I quote from a book published in 1900: ?'The siliceous lining is as much a part of the process of copper converting as magnesia lining is in the basic bessemer treatment of phosphoric iron, and it is suicidal to attempt any other kind of lining, either water-jacketed or basic.' "Even if the silica could be introduced in this way (through the tuyeres), it would still produce another trouble in the converter. The small particles of silica, being cold, would combine very imperfectly with the iron oxide and produce granulated and pasty slags, which could not be skimmed or poured out of the vessel".

Jan 1, 1942

By C. M. Acuña

At the Chuquicamata Division of Codelco-Chile high arsenic concentrates are produced, which at the smelter are processed via the Outokumpu Flash Furnace and Teniente Converters to obtain copper mattes. In the case of the Teniente Converters the production of matte grade near white metal composition is a common practice since the eighties and provided in the pyrometallurgical route no appropiate measures are taken, penalties have to be paid because of arsenic content in the anodes. During smelting huge volume of slag is produced and elimination of arsenic by slagging at this step is not economically attractive. Although during fire refining is possible to eliminate arsenic by use of mixtures of calcium and sodium carbonates this alternative is expensive, takes long process time and decreases the lifetime of the refractory lining. In spite of these facts a reasonably way to control arsenic in metal, and therefore in the anode, is taking, action in the converting step. The effects of oxygen and arsenic content in metal, arsenic in white metal and basicity index of the slag upon the distribution coefficient of arsenic between metal and slag were investigated at pilot and industrial levels. The best results are obtained for metals around 7,000 ppm oxygen and 0.3 basicity index slag, which results in a 5.7 distribution coefficient for a 5,800 - 7,100 ppm arsenic content in white metal, 18%-24% CaO slag at 1473 - 1523K. Furthermore, no significant/visible refractory wear has been realized.

Jan 1, 1999

By K H. Esbensen

The critical role of representative sampling is featured and illustrated by selected examples from the geosciences and beyond. As there already are many demonstrations of the potential (and potentially large) economic consequences of ignoring proper standards with respect to representativity, eg for mining and minerals processing companies, which æstand to lose millions of dollars by failing to optimise exploitation of their mineral resourcesÆ, such need no further iteration here.This keynote lecture, rather, takes a point of departure from the opposite perspective: what is to be gained by a scrupulous stand for representativity? Honesty, reputation, credibility, market advantage - is what!CITATION:Esbensen, K H, 2012. The critical role of representative sampling, in Proceedings Sampling 2012 , pp 9-12 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012