Search Documents

By R. L. Grant

An investigation was undertaken by the Bureau of Mines to determine the relationship between freespace and ignition probability for borehole shots. A series of experiments was concluded which covered six freespace conditions for a pemissible explosive in a 3/4-inch borehole and encompassed some 700 shots. The results were analyzed statistically. From the analysis of variance, it was concluded that the freespace means were different and that this conclusion is not impaired by possible differences in the explosives used. Within the limitation of this experiment, a definite relationship was found between the freespace and the ignition probability. Specifically, the incendivity increases with increased freespace up to a maximum; beyond this maximum there is some indication of decreasing incendivity. Further investigations are in progress to establish whether the effects of freespace on ignition probability reported here are applicable to the large test gallery, INTRODUCTION A borehole loaded with an explosive charge is a common feature of the routine gallery tests for determining the permissibility of coal-mine explosives, of Experimental Coal-Mine shots, and of the small steel cannon shots used in connection with certain research programs on the ignition of firedamp (6, 10).6/ The question of the interrelationship of freespace, weight of charge, and ignition probability of the methane-air atmosphere has been raised

Jan 1, 1959

By G. V. Sullivan, G. F. Workentine

Beneficiation studies were conducted by the Bureau of Mines on three samples of low- grade chromite - bearing material from the Stillwater complex of Montana . The objective of the study was to develop methods for recovering chromite from low- grade materials to improve the domestic reserve situation . Samples were obtained from the three largest deposits in the district , Mouat , Benbow , and Gish . The chromic oxide ( Cr₂ 0 ) content of the ore and of the chromite was about the same in each of the samples . The major gangue constituents ranged from clean olivine in the Mouat sample to such altered minerals as serpentine and talc in the Benbow and Gish samples . Tabling , flotation , high- tension electrostatic separation , and combinations of processes were applied to each ore . Treatment of the Mouat sample ( 9.95 percent Cr₂ 0 ) by high- tension electrostatic separation , a combination of tabling and high- tension electrostatic separation , and tabling with middling retreatment resulted in concentrates that graded 42.8 , 42.0 , and 40.7 percent Cr₂03 at chromium recoveries of 85 , 86 , and 84 percent , respectively . Other techniques were less selective . 2 The Benbow sample ( 7.75 percent Cr₂0 ) responded most selectively to tabling with middling retreatment and a combination of tabling and hightension electrostatic separation to produce concentrates of 40.1 and 39.5 percent Cr₂g with each process having a chromium 2 recovery of 69 percent . Response of the Gish sample ( 8.04 percent Cr₂03 ) to the various concentration techniques was about the same as that of the Benbow sample , but in general , somewhat less selective . A combination of tabling and high- tension electrostatic separation resulted in a concentrate that contained 71 percent The Mouat mine was reopened in 1953 when the American Chrome Co. contracted with the Federal Government to produce 900,000 tons of chromite concentrate . The ore , averaging 20.2 percent Cr₂03 , was treated by tabling to produce a 38.5 - percent Cr₂ O concentrate.

Jan 1, 1964

By Howard N. Eavenson

DURING the past year, as in the preceding ones, prices continued to fall, production to decrease, and more mines were closed. Much attention is being given by the industry to suggested plans for betterment of its position, and if the scheme recently brought out for consolidation of sales agencies into district agencies is loyally carried out, it cannot but help to improve conditions. The progress in the anthracite industry is shown in the report of its chairman, E. H. Suender; changes in coal preparation are outlined in the report of J. B. Morrow, chairman of Committee on Coal Preparation, while increased mechanization of the western mines is described by Eugene McAuliffe, chairman of the Committee on Machine and Strip Mining. In spite of the depression, interest in the Coal Division has been increasing, its meetings have been well attended, and its committees are active and have been doing excellent work.

Jan 1, 1932

By D H. Sharp

The Quebec Cartier Mining Company produces iron concentrate for twelve months of the year from Port Cartier. This J>Ort is designed to handle ship varying in size from 3,000 to 100,000 d.w.t., requiring 50 feet of water at low tide. The harbour was built on shore for reasons of economy and layout, after considering many more conventional offshore designs. It provides for heavy oil bunkering, tanker off-loading, a heavy lift derrick and freight handling, besides ship loading and mooring. The weather for the previous fifty years was studied to enable wind and wave conditions to be accurately assessed for design purposes, and to determine probable lost time due to adverse weather conditions through-out the year. The first ship to be loaded was 60,000 d.w.t.; the second, 20,000 d.w.t. The latter entered the harbour after dark, under its own power, following a tug through the partly dredged narrow entrance. Large ships use tug assistance. Ships may leave the loading berth with the other berths occupied.

Jan 1, 1963

By F. R. Jones, B. W. Taylor, A. R. MacPherson, L. J. Lamb

"The Lake St. Joseph Iron Deposit is in Northwestern Ontario. Exploration to date by Steep Rock Iron Mines Limited has indicated an ore reserve of 683 million long tons. Metallurgical investigations have proved that suitable oxide pellets and/or superconcentrates can be economically produced from this ore. Studies of the Lake St. Joseph iron ore deposits have covered the period 1956-71, and have embodied applications of the improvement in mining and processing technology over this period. Market demand in the early 1960's for high-grade oxide pellets as a replacement for natural iron ores for the blast furnace first drew attention to the potential of the Lake St. Joseph deposit. The current market trend toward utilization of sponge iron to replace steel scrap as feed to electric furnaces and cupolas now suggests that the deposit can better be exploited as a prime source of superconcentrates."

Jan 1, 1972

By Darren Medd

Kumtor Gold Company (KGC) currently operates the 500,000 tonnes per day Kumtor open pit gold mine located in the Issyk-Kul region of the Kyrgyz Republic at an elevation of more than 4,000 m. To supplement the open-pit mill feed with high grade underground ore from outside the current pit limits, KGC started pre-production design and development of the underground mine for the SB ore zone in late 2006. The initial phase of pre-production development consists of exploration and haulage declines which, upon completion, will provide ventilation and access to the underground mine. Design and construction of these declines presented many challenges to the project team considering the mines unique location at high altitude, the limited experience with Western underground mining techniques in the Kyrgyz Republic, and the impact of the nearby Davydov glacier and resultant ground conditions. Completion of the exploration and haulage declines was undertaken jointly by KGC and mine contractor, J.S. Redpath Limited (Redpath). The initial phase of development including several ground falls provided detailed information on geotechnical ground types and conditions that were useful in determining the overall mine design and methodology for production. This paper covers the various aspects of the design and construction process of developing the declines under the glacier, minimizing the likelihood of further ground falls, and the journey of both KGC and Redpath which led to the successful breakthrough between the declines on 01 July 2012.

Aug 1, 2013

By J. Iannicelli

An entirely new level of magnetic filtration technology was put into full commercial production by the kaolin industry of Georgia, U.S.A. during 1973-1974. At present, four kaolin producers in Georgia are operating large magnetic filters each capable of processing over 1000 gallons of kaolin slurry per minute or over 65 tons of kaolin per hour on a dry basis. A fifth large filter will go on stream in August, 1975. Four of these units are 84" machines manufactured by the Pacific Electric Motor Company of Oakland, California. When operated at the maximum 1000 g, p. m. rate, these five large magnetic filters have a combined capacity approximating the entire waterwashed coating and filler kaolin produced in the U.S.

Jan 1, 1976

By Jerrold J. Marcus

United states reserves of oil and gas have been steadily declining while consumption of petroleum products has continued to increase. The nut result has been an ever increasing shortfall between supply and demand. This imbalance has been made up by imports of both oil and gas causing a strain on the United States Balance of Payments. To complicate the situation further, exporting nations have recently formed a cartel and dramatically increased the selling price of petroleum products. To meet U.S. energy demand, increased attention has been drawn to the production of synthetic oil and gas from coal. To date, considerable research has been conducted and is continuing on various processes for liquefaction and gasification of coal. Some of these processes are now in the pilot plant stage and at least one demonstration plant has been proposed. The coal conversion complexes envisioned will be very large, requiring substantial capital investments and abundant reserves of coal. Coal production to feed these proposed complexes has been estimated on the order of 75,000 tons per day. With the viability of these projects becoming economically attractive, the Office of Coal Research initiated a contract with Fluor Utah to determine and define the problems of surface mining coal at very high mining rates, under varied physical, geographic, and climatic conditions. The flow of recent events in the Middle East has created a greater sense of urgency for this study.

Jan 1, 1975

By C Pope, M Tannock

Mining exploration and development projects in Australia are being negatively affected by the highly complex regulatory and bureaucratic processes at all levels of government. These processes affect mining companies operating in Australia by impacting on timelines and the cost of developing a mining project. It is not uncommon for the granting of project approvals to take in excess of five years, meaning that mining companies struggle with productivity, efficiency, time frame and cost issues in respect to their projects in Australia. As the mining boom in Australia is moving from the investment to the production phase, it is now more important than ever to maintain a regulatory landscape that facilitates rather than discourages new investment.While one of our key arguments is that there is too much burdensome regulation and red tape in Australia, we are also strongly believe that regulatory intervention is necessary to ensure that appropriate checks and balances are in place to serve the public interest and manage environmental, health and safety, social and other development-related impacts that may arise from a mining project. However, the regulatory intervention in Australia has come to a point where it is excessive and starting to discourage valuable investment in mining projects for nominal return to the public. Excessive regulation or ‘red tape’ impedes productivity and competitiveness, deters investment and innovation and costs jobs, all of which ultimately impact on the growth of Australia and the standard of living of all Australians.This paper aims to examine and compare the federal, state and local regulations that govern mining projects in Australia. It will highlight how these regulations are unnecessarily complex, lengthy and duplicated and how they can be streamlined to reduce red tape. In doing so, the paper will evaluate the recommendations proposed by the Productivity Commission Report on Major Project Assessments released in 2013, which include the recommendation to move to a ‘one project, one assessment, one decision’ regulatory model.CITATION:Pope, C and Tannock, M, 2015. Project development and regulation red tape – a comparative analysis: does it need to be so complex?, in Proceedings Iron Ore 2015, pp 621–630 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By D. Grobbelaar, A. Cichowicz, D. J. Birch

The Q-coda method for estimating the quality factor Q(f)= Qo(f)n was used to characterize seismic wave attenuation in a region of the Kaapvaal Craton that includes the mining areas of the Bushveld Complex and Witwatersrand Basin. Seismic waveform data, collected by locally distant stations of the South African National Seismograph Network (SANSN), consisted of mining-related events with magnitudes ranging from ML 1.8 to ML 4. Q was calculated for nine different source-receiver pairs spanning the study region. A weighted average Q based on the number of available data gave an estimated attenuation relation for the study region of Q(f) = 327 f 0.81.

Jan 1, 2015

By Kenneth K. Humphreys

INTRODUCTION What is automation? Why automate? Webster's New Collegiate Dictionary defines automation as "the automatically controlled operation of an apparatus, process, or system by mechanical or electronic devices that take the place of human organs of observation, effort, and decision." This definition gives an implied answer to the second question, "Why automate?" Automation, automatic control devices, and process control equipment receive their justification in supplementing or replacing manpower, which results in decreased operating costs. In the past, processes were operated with the minimum amount of instruments needed merely to guide operators. Processes were manually con- trolled by the operator on the basis of simple temperature, pressure, flow, and level indications on a panel. Today the tendency is to design a new plant to operate in a fully automatic manner according to a preset pro- gram utilizing a minimum of manpower. In addition to this direct cost reduction in manual labor, increased equipment capacity results from uniformity of flow and uniform control of process variables. This control eliminates or minimizes surges and permits equipment to be operated at or near its ultimate capacity and, for a given material throughput, permits the use of smaller process equipment. Automatic control, therefore, be it in the field of coal processing or in any industrial field, is simply a problem of economics. Control equipment is justified in terms of its contribution toward increasing productivity, increasing profit margins, or producing a new and salable product at a profit. Instruments and control devices can be divided into two general groups: (1) units which measure and (2) units which both measure and control a process variable.

Jan 1, 1979

By D. Gregurek

The complexity of metallurgical processes in the non-ferrous metals industry. especially changes in the process conditions in combination with a diversity of metal processing furnaces, requires a precise knowledge of the system for the selection of refractory products. However, particular importance is still focused on the specific refractory consumption being as low as possible. The addition of recycling material with a high amount of impurities and the increase of low-grade ore concentrates used in the base-metals industry also entails a significant change of slag chemistries, process temperatures, etc., which influence the performance of already approved linings. This acknowledgement of process changes with decreased brick lifetimes provided the motivation for RHI AG to develop high-performance refractory bricks especially for non-ferrous metals applications. The internal laboratory tests with fayalitic slag showed very promising results compared with our approved magnesia-chromite bricks for this application. In order to identify suitable refractory products and to improve the life of the refractory lining, innovative product development has to be undertaken. In addition, the practical corrosion testing methods and facilities available within the RHI Technology Center, such as the induction furnace and the rotary kiln test equipment, allows the best possible understanding of brick wear at a laboratory scale. Based on the results of the test work, the optimal refractory solution can be recommended for a field trial at the customer?s site.

Jan 1, 2012

By R. Woods, O. A. Kiehn, C. A. Born, F. N. Bender

Development of the flotation reagent scheme at Climax Molybdenum Company's mine at Climax Colorado is reviewed. Features of the mineralogy, milling practice and background of reagent changes are outlined. Special attention is given to the hitherto unpublished details of the application of depressants for copper and lead impurities. The present rougher flotation reagent scheme utilizes a neutral hydrocarbon oil, low in unsaturates and wax, as collector with a sulfated coconut oil emulsifier and pine oil frother. Lime and sodium silicate are used as rougher conditioning and slime dispersant agents. Chalcopyrite and galena impurities are de- pressed in both rougher and cleaner plants by stage addition of Nokes reagent and sodium cyanide to yield a metallurgical grade molybdenite concentrate containing greater than 90% molybdenite and less than 0.5%, 0.1% and 0.05% iron, copper and lead impurities, respectively.

Jan 1, 1976

By Donald F. MacDonald

METAL PRICES RISE WITHIN the past nine months, the mining industry of the world has been revivified by a spectacular price advance for the metals. ln fact, practically all geological raw materials have been marked up during this period. Reviving industry started the price rise, but the armaments race among the nations has intensified it. These factors, coupled with our decided building shortage, which must be made up, will probably maintain metal prices at decidedly favourable levels over the next two or three years, or longer. OUR MINERAL CIVILIZATION It is interesting to recall that in the past hundred years, while the white population of the world increased some three ta three and a half fold, the consumption of minerals increased seventy-five fold. In other words, ours is a mineral civilization. If we disregard short slumps, which we will occasionally experience, it seems certain that the bread upward trend in mineral consumption will be maintained for many decades into the future. Nations without reasonably abundant and diverse mineral deposits will eventually become nations without much power. Canada is blessed with a splendid store of minerals. Its mineral industry is now facing an exceptionally rosy future. What of the mineral industry of Nova Scotia? GEOLOGICAL RESEARCH ALLOWED TO LAG RN NOVA SCONA Many years ago, when geological science was in? its infancy, much geological study was carried on in Nova Scotia. In 1827, Francis Alger began work on the iron ores in the Bay of Fundy region. In 1886, E. R. Faribault began his series of remarkable papers on Nova Scotia geology. Between these dates, many others published papers on the geology of the Province. The most outstanding of this early group of geologists was Sir William Dawson, whose published works on Nova Scotian geology extended over the period from 1845 to 1891.

Jan 1, 1937

By Deno M. Pappas

This report presents results of a U.S. Bureau of Mines study of longwall gob material. The objective of this work was to determine material stiffness properties of the gob for use in numerical models of rock mass response to longwall mining, Photographs of actual mine gob were digitized to obtain approximate particle size gradations of gob material. The gradation curve was shifted down to a laboratory scale, and 20 uniaxial compression tests were conducted. Varying the maximum particle size was not found to affect the stress-strain behavior, but changing the gradation appeared to influence the stress-strain behavior. The stress-strain relationship of the simulated gob material was nonlinear, the stress-secant-modulus relationship was approximately linear, and the stress-tangent-modulus relationship was approximately a second-order polynomial function. Equations were generated from these curves, providing numerical modelers with a means to estimate gob moduli based on the stress level. In addition, the experimental data were statistically evaluated using multiple regression analyses, producing a series of equations to predict the secant and tangent moduli from the given stress level, bulking factor, rock strength, and thickness-to-width shape ratio of the particles.

Jan 1, 2010

By M. Rezaee

Push backs used in the production planning of open pit mines play an integral role in generating annual cash flow. Although several algorithms for push back designs have been proposed, none have studied the optimum number of push backs. In this paper, different algorithms have been implemented for the push back design of a cross section of a copper deposit and the results discussed. Moreover, the optimum number of push backs has been determined using analytical and multiple attribute decision making (MADM) methods based on minimizing the risk associated with grade uncertainty, and minimizing stripping ratio, while maximizing net present value (NPV). According to the findings, the optimum number of push backs has been proposed to be between three and six, as lower quantities of push backs are more likely to achieve the calculated net present value, and have smoother stripping ratios for different pushbacks. This approach was examined in an operating mine and the optimum number of push backs determined to be four.

Jan 1, 2012

By J. L. Huisman, G. Schouten

After pyrometallurgy and hydrometallurgy, bio(hydro)metallurgy is the latest development in the ongoing search for efficient and economic metal winning processes. In addition to bioleaching, other biotechnology-based applications are getting more and more accepted. In this paper a number of proven and commercial processes will be presented that can be applied for nickel and cobalt recovery and refining. These processes are based on the ability of biomass to convert the redox state of sulphur compounds under ambient conditions. They can be applied to recover sulphate from effluents or SOx from off gases and convert it to H2S or dissolved sulphide that can be reused in production or effluent treatment. Not only does this minimize the costs on resources but it also reduces waste production and improves the quality of discharges even to the point where reuse becomes feasible.

Jan 1, 2005

By C. O. Esterhuysen, J. P. Deetlefs, C. A. Wessels

The productivity indices of the Republic of South Africa compare poorly with those of its competitors in the rest of the world. The theory of productivity is relatively simple, and various models are available to demonstrate this. The problem is how to apply the theory in practice and to convert it into a practical management system that will guarantee results. The secret lies in a management approach that aims at a continuous improvement in achievement and that involves the entire work force down to the lowest level in the process. Good management systems ensuring the necessary attention to, among others, management by objectives, finance, personnel, maintenance, planning, and control are a prerequisite for continued improvement and staff involvement. The net result of such an approach is described by the term performance management, which encompasses the total integration of al a company's management systems.

Jan 1, 1989

By J. A. Organiscak

The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently studied several redirected scrubber discharge configurations in its full-scale continuous miner gallery for both dust and gas control when using an exhaust face ventilation system. Dust and gas measurements around the continuous mining machine in the laboratory showed that the conventional scrubber discharge directed outby the face with a 12.2-m (40-ft) exhaust curtain setback appeared to be one of the better configurations for controlling both dust and gas. Redirecting all the air towards the face equally up both sides of the machine increased both the dust and gas concentrations around the machine. When all the air was redirected towards the face on the off-curtain side of the machine, gas accumulations tended to be reduced at the face at the expense of increased dust levels in the return and on the curtain side of the mining machine. A 6.1-m (20-ft) exhaust curtain setback without the scrubber operating resulted in the lowest dust levels around the continuous mining machine, but this configuration resulted in some of the highest levels of dust in the return and gas on the off-curtain side of the mining face. Two field studies showed some similarities to the laboratory findings, with elevated dust levels at the rear corners of the continuous miner when all the scrubber exhaust was redirected towards the face either up the off-tubing side or equally up both sides of the mining machine.

Feb 23, 2014

By T. W. Beck, J. A. Organiscak

The U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently studied several redirected scrubber discharge configurations in its full-scale continuous miner gallery for both dust and gas control when using an exhaust face ventilation system. Dust and gas measurements around the continuous mining machine in the laboratory showed that the conventional scrubber discharge directed outby the face with a 12.2-m (40-ft) exhaust curtain setback appeared to be one of the better configurations for controlling dust and gas. Redirecting all the air toward the face equally up both sides of the machine increased the dust and gas concentrations around the machine. When all of the air was redirected toward the face on the off-curtain side of the machine, gas accumulations tended to be reduced at the face, at the expense of increased dust levels in the return and on the curtain side of the mining machine. A 6.1-m (20-ft) exhaust curtain setback without the scrubber operating resulted in the lowest dust levels around the continuous mining machine, but this configuration resulted in some of the highest levels of dust in the return and gas on the off-curtain side of the mining face. Two field studies showed some similarities to the laboratory findings, with elevated dust levels at the rear corners of the continuous miner when all of the scrubber exhaust was redirected toward the face either up the off-tubing side or equally up both sides of the mining machine.

Jan 1, 2013