Search Documents

By Keith Best

It has been said that when a person does something right no one remembers but when they do something wrong no one forgets. This statement, when applied to the explosives industry, has never been truer. Think about it.How many times have you seen a news crew reporting on how well a blaster is doing his/her job? Normally, all you will see is how bad things are going and how much “damage” is being done.

Jan 1, 2008

By S. D. Bearden

Color enhances expression and communication in all physical objects experienced in life. Pigments provide color and in some applications have a specific additional function. Natural iron oxides are widely distributed throughout the world but only a few deposits are sufficiently pure and possess acceptable color and brightness properties to merit their processing into pigment form. Ochre, the common name for goethite ore, is the best and most under used material in the buff colored pigment market. The geological occurrence of ochre in the basal Shady Formation of the Cartersville Mining District (Georgia) is described. Exploration, processing, and product applications of New Riverside Ochre Company, Inc. are discussed. An overview of the worldwide pigment market is presented with emphasis placed upon the North American activity in iron oxide production and application. The purpose of this paper is to increase the awareness of ochre and its potential market in the colored iron oxide pigment industry, encourage research on the origin of ochre deposits, and stimulate interest in new applications of this unique substance.

Feb 27, 2013

By A. S. Henderson

Eastern Mesabi taconite is one of the hardest rocks known, but fortunately it shows little tendency to pack in the crushers, when the minus 5/16 inch material is removed. The crushing circuit is essentially as shown in the Engineering and Mining Journal article, "Reserve's New Taconite Project", dated December, 1956 except that the grizzly screen between the two stages of gyratory crushing has been eliminated. The Reserve operating staffs aim is to utilize the crushing equipment in such a manner that the maximum tonnage of taconite can be crushed to the required size at a minimum cost. As is readily apparent, the primary consideration is to produce a desired size product, with the other operating factors to be balanced, thus achieving the best setting for each crusher. Much effort has been expended toward the development of a satisfactory sized material for feeding the rod mills. The characteristics of this feed must allow the following situations to be handled by the existing equipment: 1. The material being fed to the rod mill must be such that it can be fed into the unit with the proper quantity of water to maintain the correct density within the mill. 2. The rod mill must produce a product from this feed which can be handled without difficulty by the magnetic cobbing and ball mill circuit. 3. The incidental tramp must not exceed that quantity which can be handled easily after the rod mill and after the ball mills.

Jan 1, 1959

By R. B. Taylor

The Esmeralda mine is located about three miles west of the town of Parral, in the State of Chihuahua, Northern Mexico, and about 400 miles south of El Paso, Texas. The area is serviced by the Interamerican Highway and a branch line of the National Railways of Mexico. The Parral district is quite typical of the semidesert of Northern Mexico, lying near the western margin of the Chihuahua basin and range province known in Mexico as the ?Mesa Central? In the immediate mine area, low rounded hills and rolling plans slope toward the Parral River. Surface elevation at the mine is 5,800 feet. The Esmeralda vein outcrops strongly, but was too low grade to be of interest to the Spaniards, The first claims were staked in 1897 and limited exploration work to a depth of 550 feet was carried out prior to 1912, at which time work was suspended. The Eagle-Picher Company acquired the property in 1944 and by surface diamond drilling outlined an orebody to a depth of 800 feet, Minas de Iguala, S. A, de C.V., one of Eagle-Picher?s totally owned subsidiary companies in Mexico, then unwatered the old workings, developed the mine, installed a modern differential flotation plant and started production lage in 1948. To the present, more than two and ahalf million tons of ore have been mined and milled producing lead and zinc concentrates.

Jan 1, 1958

By Sharon L. Eyer

"FTIR spectroscopy is employed to define mineable ore deposits based on exploration samples. The RAMBO (Robotic Assessment of Mineable Bauxite Ore) technology is operating successfully at an alumina refinery in K winana, Australia, for assessment of a number of critical ore attributes including available alumina, extractable organic carbon and total iron. Classical methods of analyses for these properties require laboratory-scale digestion of alumina ore (bauxite) or XRF analyses.Multivariate calibration is used in the RAMBO system to generate robust mathematical models that are able to estimate classical data from FTIR spectral data. Furthermore the models can highlight regions of ore that are relatively unusual. Unusual ore may be investigated for potential impacts on refinery processes well in advance of mining.The components of the technology are described and some results for an example application (bauxite) are presented. Challenges and difficulties are discussed. The potential to apply the technique to process control is introduced."

Jan 1, 1999

There is no doubt that the mining sector is considered to be the backbone of many countries. Furthermore, it has played an important role in the prosperity of nations, whether developed or developing. Saudi Arabia is one of these countries that has a large variety of metallic and non-metallic mineral resources that range in size and value occurrences of limited potential to deposits large enough to sustain profitable exploitation. Therefore, the Saudi government needs to reinforce the capacity of the sectoral institutions to better regulate and promote the sustainable development of the sector. The ability to overcome the administrative and legal complications that constrain private sector participation in the minerals sector, through new mining code which will streamline the procedures for obtaining licenses and will add more predictability and transparency to the application process, are proposed for increasing the sustainable development. This paper will outline how the Saudi government is tackling the major challenges that face the minerals industry. This paper provides the background to the Saudi Arabian mineral sector and its industrial base. Finally, the paper identifies the problems and constraints that face the minerals sector in Saudi Arabia and provides an assessment of the effects of government policies and planning efforts in the minerals sector, particularly during the period of the development plans which started in 1970.

Jan 1, 2009

By Cecil E. Lester

Since the advent of coal mining, the minimal lighting in the under¬ground working place has been an obstacle to the safe and efficient performance of the miner's many tasks. Compounding this problem is the fact that the machines being operated in the working place are so large that the vertical and horizontal clearances around the machinery are severely limited. Consequently, in these poorly lighted and congested working places, the machine operator is unable to utilize his peripheral vision. He cannot see hazards as they develop and, too often, cannot react in time to avoid serious injury or death to himself or his fellow miners. The greatest hazard to miners inby the last open crosscut is from falls of roof which are often preceded by warning signs such as falling rock fragments, roof supports taking weight, or a sudden reduction in the height of the working place. These warning signs often go undectected because the machine operator's attention is focused on the small circle of light emitted from his cap lamp. Congress recognized the illumination deficiencies, and, in the Federal Coal Mine Health and Safety Act of 1969, charged the Secretary of the Interior with the authority and responsibility for development and promulgation of minimum standards for illuminating working places in coal mines. These standards have been developed and, as stated in the April 1, 1976 Notice, Federal Register, Volume 41, No. 64, will be promulgated on October 1, 1976, as mandatory regulations under Section 75.1719, Title 30, Code of Federal Regulations. The regulations require that the designated surfaces within the miner's normal field of vision be illuminated to 0.06 foot-lamberts while self¬propelled mining equipment is being operated in the working places. The term "working place" is defined in the Act as "the area of a coal mine inby the last open crosscut".

Jan 1, 1976

By ROBERT R. ABUOTT

(Cleveland Meeting, October, 1912.) THE practice of carbonizing steel for the purpose of case-hardening has assumed great commercial importance within the past, 10 years. Formerly, case-hardened steel was held in more or less contempt, since it. was considered a cheap substitute for tool-steel. This is no longer the case. The development of the motor-car industry, and coincidentally that of modern alloy-steels, has resulted in overcoming many difficulties formerly experienced in case-hardening. This result has been accomplished by increased knowledge regarding the analysis of the steel which would respond most readily to case-hardening, and by more careful methods of treatment of the carbonized steel. The ordinary method of carbonizing consists in packing the steel with the carbonizing-material in cast-iron boxes and placing them in a furnace at a temperature of from 1,500° to 1,900° F. for a time sufficient to give the required depth of cc case." The steel is then either quenched directly from the box, or is allowed to cool without unpacking, and finally given a single hardening-heat., or, for special work, two or three heats. During the year 1911, more than 100,000 tons of carbonizing-material was sold in the United States, at an average price of probably $55 per ton. More than 85 per cent. of this material consisted of granulated bone. Within the past four years, many manufactured compounds have been placed on the market, consisting largely of some form of carbon or carbonaceous material, with or without the addition of chemicals. Steel will absorb carbon placed in contact with it at the temperature of the atmosphere. The reaction is exceedingly slow, but. increases rapidly with increasing temperature. Below * Metallurgical Engineer, The Peerless Motor Car Co.

Dec 1, 1912

The National Mine Health and Safety Academy near Beckley, W. Va., is dedicated to reducing accidents and improving health conditions in the mining industry through education and training. Though this basic mission remains unchanged, the Academy now serves a much broader mining community than it did when established in the late 1960s. From its original emphasis on training federal coal, metal, and nonmetal mine safety inspectors, the Academy has expanded its programs to reach mining industry and labor representatives, state agency employees, and university students taking mining-related courses. The Academy's resident programs, short courses, seminars, and continuing education courses cover a wide range of subjects and various experience levels, but all have been developed with one idea in mind - to reduce accidents and health hazards through education and training of the widest possible audience.

Jan 11, 1979

By R. L. Morse

The thermodynamic program is similar to previous mine ventilation programs but has been expanded to consider the compressibility of air. The thermodynamic program does consider: 1) air density variations, 2) humidity changes, 3) intake, exhaust, and underground fans, 4) heat transfer between rock and air, 5) refrigeration of heating plants, both surface and underground, and 6) heat generated by equipment, both diesel and electric. 110st of the compressibility factors are handled in the branch calculations. The field survey necessary to supply-data for this program is quite similar to the basic base and leap-frog pair of stations method used with most incompressible mine ventilation programs. The thermodynamic program is a complete package of ventilation network analysis which can provide mine management with good operational control and planning of mine ventilation systems.

Jan 1, 1977

By Jerry Ran

When multiple levels are mined in open stope mining with delayed backfill, mining underneath fill is inevitable to achieve higher rate of recovery if no sill pillars are left for the purpose of fill separation or partial ground support. This is particularly true when the orebody has low reserves per unit vertical distance. Instability of the exposed fill back causes stope dilution, production delay and possible equipment damage and consequently increases the mining cost. Previous studies have concentrated on fill mat stability in cut-and-fill and stability of fill walls in open stope mining. Workers are exposed to the fill back in cut-and-fill and therefore smaller open spans are normally adopted and the fill mat is reinforced. In open stope mining openings with large spans are designed, workers are not exposed to the fill back and its stability has to be maintained by fill of sufficient strength. However, the required fill strength is normally determined by considering different modes of fill wall failure. The fill back stability is usually not analyzed in the fill design process. The lack of analysis on fill back stability for open stope mining is mainly due to difficulties in relating the fill properties to the fill and stope geometry. In this paper a simplified wedge model is adopted to analyze stability of the exposed fill back in open stope mining with consolidated backfill. The proposed method calculates the factor of safety of the fill back against shear failure under known fill and stope geometry and fill strength parameters in order to assess the fill back stability. It can also be used to determine the required fill strength with known fill and stope geometry. The proposed approach is indirectly validated by mining experience and observations at two operating mines. In addition there are many factors affecting the fill quality and stope configurations in an operating mine. These factors have to be considered in the analysis of fill back stability. This situation is highlighted by presenting an actual mining case where the fill back failed due to factors commonly encountered in mining operations.

May 1, 2003

By G. P. Salas

I.- In order to keep pace feeding its fast growing population, Mexico with only about 20% of its surface suitable for intensive agriculture, will need the application of modern foodgrowing techniques. To assure greater crop yields it will be necessary to apply more fertilizers than used at present (yearly average of 29 Kgs/hectare)** For its fertilizers production Mexico still depends mostly on imports of phosphate concentrates from Florida, U.S.A., Morocco and Spain. To reduce or eliminate this dependence on foreign providers, the Consejo de Recursos Minerales -a Federal Government exploration Institute- started in 1974 an exhaustive exploration program for phosphate deposits more amenable to commercial exploitation than the phosphatic limestones contained within the La Caja Formation of Upper Jurassic, found along the Sierra Madre Oriental. After studying literature on the origin and deposition of marine phosphate and visits to deposits in Florida, U.S.A., the Baja California peninsula was selected as most favorable for starting this program because of its geologic and sedimentary history and also for its geographic location, where the cold California and warm Counterequatorial currents meet. Exploration activities executed by FORNOS, S. A. (1956) led to the disco very of low grade phosphate (3 to 5% P2O5) in the recent beach sands along the Bahia de Magdalena (Fig. # 1). In his doctoral thesis Bruno D'Anglejan Chatillon (1965) reports the presence of nodular phosphate on the continental shelf, between Isla Margarita and the Vizcaino peninsula. He estimated reserves of up to 1.5 million tons. A Mexican-American marine exploration company attempted in 1966 the evaluation of this deposit with negative results.

Jan 1, 1978

By Steve Kral

Commodity price down cycles are a fact of life in the mining industry. And companies pre-pare for them as best they can. Evenso, operations are still curtailed or closed during those cycles, profits shrink, layoffs are inevitable and many companies do not survive. However, one of the few good things that occurs during down cycles is the new, innovative exploration, mining and processing technologies that come about during hard times. To survive the lean times, the mining industry turns to improved technology to decrease costs and hold the bottom line. And, because mining is a cyclical business, each down cycle brings about technology improvements that carry over into the good times.

Jan 1, 2004

The knowledge in the field has been reviewed by literature studies, and using experience from personal research in sublevel caving. There is a lot of material regarding gravity flow of fine grained materials in bins, but the theory of flow for these materials are normally not applicable for coarse blasted rock. This study was therefore concentrated towards coarse rock fragments created after blasting in orebodies. The goal for this study was to make a report of known knowledge, and identify what we have to learn more about. The Bergmark-Roos theory, which was a paradigm shift in the science of gravity flow, is today the best mathematical theory for calculation of the drawbody for a homogenous material or when we wish to simulate the mean drawbody for a large number of draws. The Bergmark-Roos theory must however be improved, so it can take into account the flow pipe effect. When this is done it will be possible to construct a 3D computer model for calculation of ore extraction versus amount of loaded ore and waste. It is also necessary to find the 3D shape of the flow cone to be able to calculate the 3D ore rest that normally develops on footwalls. Calculations should be done for the draw on several sublevels including determination of the ore losses and temporary ore rests. First when this computer model is developed optimisation of ore recovery and waste rock dilution can start for a given orebody. The author points out the importance for international co-operation and standardisation of methods for determination of material properties. More field tests and model blasting tests should also be done. When enough knowledge is gathered, a handbook of the optimisation of sublevel and block caving should be written.

Jan 1, 2000

By Irving Hartmann, Bernard Lewis, John Nagy, H. P. Greenwald, H. C. Howarth

"ORIGIN OF INVESTIGATIONThe Federal Mine Safety Code for Bituminous Coal and Lignite Mines of the United States, July 24J 1946, contains the following provisions with regard to rock dusting: Article VI. - Section 2. Rock dusting.(a) All mines, except those mines or those locations in a mine which are too wet or too high in incombustible content to propagate an explosion, shall be rock-dusted to within 80 feet of the faces of rooms and entries; however, if the mine or any part of it is wet but becomes dry, the mine or portion of the mine so affected shall be rock-dusted as ·soon as it becomes dry. (b) In mines partially rock-dusted or in mines that are required to start rock dusting, haulageways and parallel entries connected thereto by open crosscuts shall be rock-dusted. Back entries shall be rock-dusted for at least 1,000 feet outby the junction with the first active entry. Inby this junction, the rooms, entries, and crosscuts shall be rock-dusted by generalized rock dusting as provided for in section 2(a).(c) Where rock dust is applied, it shall be distributed upon the top, floor, and sides of all open places and maintained in such quantity that the incombustible content of the mine dust will not be less than 65 percent. In trackless entries and air courses, protection in lieu of generalized rock dusting may be had by using bags filled with rock dust, if they are placed at regular intervals and staggered as described in Bureau of Mines Report of Investigations 3411."

Feb 1, 1948

By James A. Clem

Approximately 2,000 years ago, the Lord Admonished the Scribes (Lawyers) and Pharisees (Religious leaders of that time) that they had paid the tithe but had omitted the weightier matters of law, Judgement, Mercy, and Faith. (Matt. 23:23). I want to talk about "The Weightier Matters of Law." In a situation where big government is trying to have an effect on even small details of a work activity, otherwise simple situations become complex. Regulations are written to such detail that constant compliance with strict interpretations can be a nightmare--not to mention off the target of the intended purpose for the regulation. One soon re- cognizes the oneros characteristics of Federal statues

Jan 1, 1979

By F. Samimi Namin

During the process of developing surface or underground mines, some sites are considered for dumping of surface soils, while others are applied to reclaiming surface and waste disposal. For each kind of overburden, whether it be waste rock, low-grade material, or process tails, a separate storage site is considered so that it becomes possible to transport or recover the overburden separately. Decision-making must be completed by means of a selection process which takes into account the best methods of alternative sets in order to achieve these goals. This decision- making involves many parameters that are inter-related in that changes in some parameters affect the others. There are many methods of decision-making, however, Fuzzy Multi-attribute Decision-making (FMADM) and its functions are studied in this paper. The advantages of this method lies in its theoretical background, formulation, revising capability, unlimited alternatives, and consideration of the counteraction of the different parameters upon one another.

Jan 1, 2007

By James H. Cobbs

The utilization of large diameter drilled holes for mine shafts seems to have had its beginning in Europe about 1850 (28) where the mining industries of Germany and The Netherlands first used drilled shafts. Recent shafts in softer formations of diameters as large as 25 feet and as deep as 1, 700 feet have been drilled in both The Netherlands and Germany. The first shaft drillers utilized cable tool or churn drilling techniques which limit both hole diameters and drilling speeds. Though some churn drilling of shafts is still performed, rotary drilling has been the dominant technique for many years.

Jan 1, 1973

By T. Harrison

Surface coal mines in West Virginia are receiving stringent NPDES discharge limits for total recoverable selenium. With limits in the low parts-per-billion range, selection and implementation of proper sample collection and analytical methods are imperative for quality assurance and control and for consistency in results. Given the typical oxidized form of selenium in the water, the low limits and the large and variable flow rates from the watersheds, end-of-pipe treatment is difficult and cost-prohibitive to implement. Discharge locations in the remote and steep terrain exacerbate the problem. To evaluate options for end-of-pipe treatment at a Patriot Coal Corporation surface mining operation in West Virginia, CH2M HILL performed wastewater characterization for a range of key constituents and selenium species at three outfalls for selection and preliminary sizing of appropriate treatment processes. A preliminary evaluation of base and wet-weather flows was done to understand flow variability considerations for discharges. A conceptual evaluation of technologies to treat selenium to permitted levels was conducted in con-junction with order-of-magnitude life-cycle cost estimates.

Jan 1, 2010

P.T. Freeport Indonesia's latest expansion has increased total mill throughput to 125,000 dry metric tonnes per day. The most recent expansion included the installation of a Semi Autogenous Mill designed to treat more ore than any other single SAG mill currently operating in the world. Also included in the expansion were two large ball mills, rougher and cleaner flotation including conventional and column cells and a regrind circuit. All equipment is supported by a modem distributed control system. This paper describes the design considerations, construction, commissioning and start-up of the SAG concentrator and support facilities and includes an overview of the oreflow and milling facilities.

Jan 1, 1996