Search Documents

By A. Sariisik

This study analyses the results of a pilot trial of a newly developed armed-chained stone-cutting machine. The machine was developed in Turkey and trialed at the Kaklik/Kocaba travertine quarries in the Denizli District. An armed-chained cutting machine is an alternative to the diamond wire cutting method more frequently used in the production of natural stone quarry blocks, and increases production efficiency and quality. Since there is no need to collapse the blocks using the armed-chained cutting production process, there is no risk of the block developing cracks. This results in a considerable increase in the efficiency of natural stone block production. The armed-chained cutting machine is easier both to assemble and run when compared to other block cutting methods. This process resulted in the production of a larger number of blocks at a lower cost within the same time frame, particularly in travertine quarries and in all other natural stone quarries. The block efficiency in travertine quarries was calculated as 65?80%using the armed-chained cutting machine, compared with 7?14% using the normal diamond wire cutting method.

Jan 1, 2010

By A Kobzev, C Robben

Sensor-based particle sorting of gold ores is the masterclass of preconcentration. The technical challenges of a grade in ppm scale makes a direct detection with currently available technology in milliseconds impossible. Consequently, the detection and classification of particles into ore and waste classes relies on detectable proxies which are the foundation for the classification. These must be reliable and repeatable across the ore bodies processed in future. A sensor-based particle ore sorting equipment must therefore be calibrated systematically by understanding the gold deportation in different lithological groups. Also, it must be in best operational state to minimise possible misplacement. The technical challenges are met by a stringent financial regime governing the business case. Many gold ore sorting projects require a stable grade of gold in the rejected waste significantly below 1gr/t. Two examples are introduced in this paper:  The pilot results and operational experience of X-ray transmission (XRT)-based particle ore sorting for pebble sorting of sulphide associated ore;  Laser-based particle ore sorting for pebble circuit of an orogenic, quartz associated gold ore. Usually, sensor-based particle sorters are installed in the crushing section of a plant. However, for large capacity plants, the number of equipment required, and the associated material handling costs result in significant capital and operating expenses for plants with 1200tph run-of-mine capacity. As a conclusion, it was decided to investigate sensor-based particle ore sorting applied to the pebble stream of two existing semi autogenous mills.

Nov 10, 2020

By X Sun, L B. Zhou, H Yi, X Tang, P Ning

The rapid industrialisation in China has consumed large amounts of various industrial raw materials, which has left behind large quantities of industrial solid wastes produced from the processes of mining, mineral processing and smelting. The storage of huge quantities of industrial solid wastes is an obvious risk to the environment and human well-being. As the first step to fully appreciate the scale of this risk, it is necessary to carry out research for developing a pollution source environmental risk assessment system (PSERAS), especially for the typical staple industrial solid waste (TSISW). This paper aims to discuss the frame of the PSERAS for TSISW for large scale production. This system consists of two aspects: predicted factors and accidental ones, which involve physical, chemical and biological risk assessments, on-site and during transportation process. Two analysis methods, the analytic hierarchy process (AHP) and fuzzy logic assessment (FLA) were used to handle the complexity of environment and non-quantitative data. The risk assessment system for such a complex objective is difficult and the assessment of relative factors is problematic through the usual quantitative analysis. With the proposed PSERAS, it is possible to define the risk class of pollution sources. Furthermore, the risk assessment results will be helpful to the decision-maker, especially when facing unknown risks in the environmental management of industrial solid wastes. In addition, by means of the PSERAS, risk factors can be ranked against their contributions to environmental risk, in order to calculate their relative priorities in decision-making.CITATION:Sun, X, Ning, P, Tang, X, Yi, H and Zhou, L B, 2012. Environmental risk assessment system for typical staple industrial solid wastes, in Proceedings Life-of-Mine 2012 , pp 301-304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By J. J. Wallaert

The decreasing supplies of natural gas and low-sulfur crude oil available for electric power generation in the United States will unquestionably shift the emphasis to nuclear and coal fired steam power plants in the immediate future. Failure to do so will ensure our dependence on mid-east low sulfur crude oil comprising some 70% of the known world reserves, and imported liquid natural gas. By contrast, the United States has 43% of the known world reserves of anthracite, bituminous and semi-bituminous coal and 48% of all known coal reserves of the world including lignite. It is evident, therefore, that coal is alive and well and will continue to be a significant energy source for the production of electricity for many years. Of course, concern for our environment and the development of new technologies will ultimately curtail the utilization of coal for the generation of bulk power, but information released by the National Electric Reliability Council and the Federal Power Commission is worth repeating. In the year 1972 the total capacity of generating units in the United States was 379,552 Mw of which 149,974 Mw, or 39.5% of the total, was produced by coal fired steam turbines which consumed 344,700,000 tons of coal. New capacity additions planned or in construction show that in the year 1981 our total generating capacity will be 843,503 Mw, of which 257,995 Mw, or 30.6% of the total, if from coal only. Translating this increase into terms meaningful to the bulk material handling industry suggests that ten years from now the utility industry will require 590,000,000 tons of coal per year - a monumental task - if we are to sustain our current demand rate for power.

Jan 1, 1973

By Derrick Hunter, Pat Feighan, Keith Chrystall, David Wells

"Equipment which may be remotely operated, has some degree of on-board intelligence, and which for periods of time may operate autonomously, is referred to as telerobotic. Recent advances in electronics, computers and hydraulic equipment have dramatically reduced the cost and simplified the process of converting standard industrial equipment to telerobotic control. The benefits of telerobotic equipment include improved safety by removing the operator from dangerous situations, reduced maintenance costs and increased productivity. This technology has been proven in various military, nuclear, and police applications.The surface mining industry has expressed an interest in automation and is characterized by a willingness to use remotely operated equipment, however, the majority of telerobotic equipment currently in use is experimental or prototypical. Potential applications of telerobotic equipment for surface mining include remote operation of equipment near dangerous high walls and other unsafe areas, utilization of robotic trucks for routine hauling operations, and control of jointed equipment. In addition, component technologies of telerobotic systems are relevant to various forms of condition monitoring, operator feedback systems, and vehicle positioning.Attention must now be directed toward resolving more complex problems associated with enhancing feedback to the operator, improving the man/machine interface, and ultimately, improving efficiency. Removal of the human operator from the work site introduces significant complications in replacing the sensory inputs that an operator normally uses to efficiently run his machinery. These can be difficult to define and even more difficult to replicate remotely and may include restrictions pertaining to vision, hearing, and touch.In cooperation with Defence Research Establishment Suffield and the Alberta Research Council, Robotech Industries Ltd. is pursuing the development of additional technologies to further enhance an operator’s ability to control remote telerobotic equipment. These developments include a head-mounted display, additional control station displays and improvements to coordinated motion control software. Prototypes of these developments are expected to be completed and tested by the fourth quarter of 1997."

Jan 1, 1996

By Gilbert E. Doan

WHEN metallurgists and other engineers meet their college classmates or former teachers, the conversation will frequently become reminiscent and finally turn to engineering education. These graduates have tested the value of their college training in the hurly-burly of the outside world so respectful attention is due their opinions, which, strangely enough, fall into two opposite categories. A member of one group expresses a deep-seated conviction that engineers should have a fuller foundation of physical chemistry, another asks for a more thorough training in mathematics, others wish a more thorough grounding in refractories, a series of courses in petroleum engineering, or in electric welding. Each alumnus of this group

Jan 1, 1937

By J Franke, C Gonzalez

One of the regular tasks of geotechnical and mining engineers is the measurement and management of deformation in underground excavations. Although several methods are used to do so, the incumbent methodologies for monitoring deformation and ground support serviceability are limited to the use of visual observations or measurements at discrete points, resulting in a qualitative assessment only. The introduction of LiDAR technology allows a quantitative assessment across the entire excavation volume and its rock surface, by collecting a full three-dimensional image of the entirety of an excavation such as an underground drive, decline, or a tunnel. Comparisons between epochs of complete 3D data coverage allows for change detection over time that doesn’t feature otherwise typical omissions. The implementation of regular scanning has shown to be highly advantageous for mines with swelling or squeezing ground, but also at mines with rapid deformation. Despite the LiDAR potential, its adoption has been slow. A key reason for that is that working with point clouds is foreign to most geotechnical engineers. Point clouds have long been the realm of surveyors, but to fully adopt their use in geomechanics requires retraining, upskilling, and devotion by the individuals and the company. Sites are already stretched, so often there are insufficient resources to be applied to bringing the new technology into use. The solution to this hurdle is to partner with subject matter experts to achieve the desired high-quality outcomes without the commitment of time by geotechnical personnel. This paper presents a new solution of fully automated raw LiDAR point cloud data processing that not only enables geotechnical engineers to avoid having to learn unrelated skills by allowing for deformation monitoring without associated training or expertise, but it also provides instant reporting results as well as a sophisticated database with features otherwise not available. All data processing time and effort is completely replaced by an automated process which at the same time opens up the opportunity to monitor many more excavation volumes at a higher frequency than is possible with conventional tools and methodology.

Nov 29, 2022

By Robert Matusewicz

Ausmelt Technology has been applied to the recycling of spent pot liner (SPL) generated from primary alnminum production. The process is centered on the Ausmelt furnace, in which the SPL is converted under high temperature, oxidizing conditions to an HF containing gas stream and inert slag. fluorine is recovered from the SPL as HF gas and is concentrated and used to manufacture AIF) for recycle to the aluminum smelters. Approximately 87% of the fluorine can be recovered and converted to AIF), with the remainder being effectively tied up in the by product slag. Cost projections show that the recycling process will be competitive with other processes for SPL. The production and recycling of AIF) provides available credit that significantly offsets the operating cost of the facility. Ausmelt Technology for recycling of SPL is currently being marketed in North America by Ausmelt Technology Corporation in Denver, Colorado, and in the rest of the world by Ausmelt Limited of Dandenong, Australia.

Jan 1, 1996

By Everett H. Dobbs

The Tripoli deposits in the southwest corner of Missouri In Newton County and the northeast corner of Oklahoma in Ottawa County, located in the vicinity of Seneca, Missouri, contains an unusual and peculiar form of silica which has not been found any other place in the world. Its outstanding characteristic is the physical structure of the individual particle, The particle structure of the Missouri-Oklahoma type Tripoli accounts for its market. It is a soft, friable, porous, double-refracting silica of the chalcedony variety, The particle is porous, has a fibrous structure, no sharp edges or comers, ad an average size of less than .01 millimeter, It varies from 90 to 98 per cent Si02 with less than 1 per cent free silica in the form of quartz, 24; has ignition loss of 1 per cent and fractional percentages of iron, alumina, lime, etc.

Jan 1, 1960

By W. Chae

The influence of solution ionic strength (IS) and electrolyte valence on the flotation behavior of malachite has been investigated. The microflotation tests were conducted over a range of solution IS (1?300 mM) at a constant speed (340 rpm), pH (9.5), flotation time (10 min), and sodium oleate dosage (5.3×10-7 moles/g). The size of malachite ranged from 45 to 53 µm, and two different types of electrolytes (NaCl and CaCl2) were employed. Electrophoretic mobility was also measured over the same IS range employed in the microflotation study. Overall, strong coupled effect of solution IS and ion valence was observed. Specifically, the flotability of malachite increased with increasing IS in the presence of monovalent cation (Na+) while the flotability increased up to 30 mM and decreased with increasing IS in the presence of divalent cation (Ca2+). Notably, the flotability of malachite was greater with the presence of Na+ compared with Ca2+ under high IS conditions (IS>30 mM). Consistent trend for Na+ versus Ca2+ was observed from the flotation results with different SO dosages. The characterization and flotation results suggested that the trend was likely attributed to the increased unfavorable interaction between malachite and bubble via the charge reversal of bubbles and malachite at higher IS in the presence of Ca2+.

Feb 27, 2013

By W. L. Stuewe

The Dominion Steel and Coal Corporation requires enormous quantities of bricks each year for its Sydney steel plant operations. Clay brick of all types are purchased, while silica brick is made in the Company's plant at Sydney. A description of this plant was given in a paper presented by H. B. Gillis and F. C. Morrison at the 1938 Annual General Meeting of the Institute. The rock used to make silica brick was for years obtained from a quarry at Leitches Creek, about eighteen miles from Sydney. Due to the gradual deterioration of this deposit, the Corporation was forced to look for other sources of supply. In 1945, the problem was presented to the Nova Scotia Department of Mines and, through the efforts of Dr. A. E. Cameron and Mr. J. P. Messervey, an examination was made of a silica-rock deposit some six miles northwest of Yarmouth, N.S. Preliminary samples proved satisfactory, and arrangements were made with the Department of Mines to ship to the steel plant at Sydney a fifty-ton car load for the purpose of further testing. Brick made from this sample shipment stood up very well in the furnaces. At the same time, two hundred and fifty tons of silica rock from a deposit at Lac Bouchette, Que., were purchased from the Industrial Silica Corporation, and brick made from this rock also was found suitable for our requirements. Comparative transportation costs, however, led to a decision to open the Yarmouth deposit. The silica rock, or quartzite, of this deposit outcrops at Chegoggin point along what is known as the 'Pembroke shore', a northerly trending section of the coast-line at the extreme southwest of the Province, in Yarmouth county. The country here is fairly flat, with elevation averaging about twenty feet above high tide, and is for the most part mantled by a growth of brush and some scrub trees, chiefly small fir. Bed-rock is generally concealed beneath three to four feet of clayey soil, but scattered outcrops of the quartzite indicated that a band of this rock, some 260 feet wide, extended inland in a northeasterly direction from Chegoggin point at least to Utleys lake, a distance of about three miles.

Jan 1, 1947

By R. A. Hatch

The United States depends mainly on foreign imports, principally India, for an adequate supply of sheet mica suitable for its many uses in the electrical and electronics industries. Sheet mica has, in fact, played an indispensable role in developing these industries,4/ and, in turn, the products of these industries (radio, radar, electric motors, and many others) have become indispensable to the military forces. Because or these conditions, sheet mica in its better qualities long has been classified as a strategic and critical material, and from this stems the wide-spread interest in substitute materials of which synthetic mica is one potential type. The United States Departments of the Navy and the Army entered into a cooperative agreement with the Bureau of Mines in 1947 to study ways and means of synthe-sizing and growing mica crystals. This is one of a series of reports5/ that describe the results of this program.

Jan 1, 1956

Since March 28, domestic producer prices on 99.5 percent aluminum ingot have been at 5l¢ per pound. Dealers in this same time frame have held ingot quotes at 49¢-50.5¢ per pound. COBALT: Imports from southern Africa in 1976 constituted 73 percent of total cobalt imports. Moreover, the United States is 98 percent dependent on imports of cobalt. For this reason, the Bureau of Mines is closely monitoring developments abroad to ensure an advance notice of any possibility of a shortfall in supply. Included in these imports were those from Zaire (41 percent directly from Zaire and 15 percent via Belgium-Luxembourg), Zambia (11 percent), and Botswana (6 percent). Also being closely watched are industry stocks.

Jan 1, 1977

By D. S. Kingery

Owing to changes in State mining laws, the Maryland Bureau of Mines requires all mine foremen to have a thorough, practical knowledge of mine gases and the limitations and use of recognized gas-detecting devices. This requirement involves immediate training of second-grade mine foremen and aspirants to qualify them for certification under the new law. Cooperation of the Federal Bureau of Mines was requested, and a plan for training was discussed and adopted. The methods used in Maryland aroused unusual interest by participating individuals, and the final results were very satisfactory. Consequently, it is thought that this plan will be of interest and assistance to other organizations faced with the need for such training.

Jan 1, 1952

The revised estimate of coal production in January 1977, is 39 million tons -- down 12 mi 11 ion tons compared with production in January of last year, largely as a consequence of the snow storms and cold. The major coal-hauling railroads operating in Eastern and Midwestern States reported to the Bureau of Mines that they loaded approximately the same number of cars for the week ended February 5, as in the preceding week. The Bureau of Mines estimates that U.S. coal production for the week ending February 5, 1977, was approximately 8.5 million tons, or nearly 3.5 million tons less than production for the corresponding week in 1976. Coal production from January 1 - February 5, 1977, was approximately 47.8 mi 11 ion tons compared with production of 63.5 million tons for the corresponding period in 1976. As of the first week in February, river and truck shipments of coal in the Eastern U.S. were about one-half of the normal traffic. Despite the freezing weather and ice and snow conditions of rivers and highways and reduced rail shipments, there was reportedly little or no shortage in coal supply to consumers. Inventories at electric utility plants and steel company coke plants at the beginning of the severe weather were sufficient in most cases for at least 30 days" operations. There have been no reports of coal shortages at other industrial plants.

Jan 1, 1977

By James R. Jones

The tempo of air pollution control regulations has increased dramatically in the past few years. Because coal mining operations are frequently located in remote areas away from urban developments, specific regulations applying to coal mines have received lower priority and are thus only now being promulgated and/or enforced. Therefore, many mine operators are not yet familiar with the regulations and the impact upon their method of operations. Few have been faced with an inspector on the property sighting them for specific violations. Several of the Mid-western states are just now requiring permit applications to be submitted.

Jan 1, 1973

By D. N. Hillhouse

The economics of exploration target selection can be measured ultimately only against a company's success at developing mines. In the following brief history of the mine acquisitions of one company, Placer Development Limited, I try to identify the principal targeting parameters and the principal skills that came into play for each property and examine how these have changed with time. The process of target selection in exploration is directed: - first by corporate investment criteria which define objectives and acceptable levels of risk for pursuit of those objectives; - second by experience and skills which permit us to minimize risk; and - third by anticipation of future events relating to ore discoveries and changes in external risk factors.

Jan 1, 1984

By Steven G. Grannes

This U.S. Bureau of Mines report summarizes Federal mandatory belt conveyor automatic fire suppression system installation requirements and inspection procedures, identifies system failure modes observed during in-mine investigations, and suggests system design and maintenance upgrades which, if implemented, would result in an improvement in overall system reliability. This report is a compilation of recommendations based on discussions with Mine Safety and Health Administration (MSHA) inspectors, review of manufacturer's literature, discussions with mine personnel, and research investigations of automatic fire suppression system performance in the laboratory and in mines. The Code of Federal Regulations (CFR) requirements for installation, inspection, and maintenance of fire suppression systems should be regarded as minimum standards.

Jan 1, 1990

This study estimates costs of producing bituminous coal and lignite by strip-mining methods in 12 hypothetical mines. Basic costs are developed by geographic area, rank of coal, and output capacity. Seam thickness and depth and type of overburden are considered typical for the area in which the hypothetical mine would be located. The cost analyses are based on the use of new equipment, the prevailing union wage scales, and the payment of all miscellaneous costs including royalties, contributions to the miners' welfare fund, and license and permit fees. All model mines are considered to have a life span of 20 years. Capital costs of bituminous strip mines with a capacity of 1 million tons per year range from $12.7 million in the Appalachian region to $16.0 million in the Interior province. The corresponding selling price, assuming a discounted cash flow return of 12 percent on investment, is $5.40 and $6.95 per ton, respectively. For bituminous coal strip mines producing 3 million tons annually, a capital investment of $24.9 million will render a selling price of, $3.46 per ton in the Interior province, whereas a similar mine in the Appalachian region requires a capital investment of $28.0 million to produce coal selling for $4.01 per ton. Subbituminous strip mines of 5 million tons of output per year range in capital costs from $28.7 million in the Southwest to $13.9 million in Wyoming and Montana. Coal produced in the Southwest would sell for $3.03 per ton, while coal from Wyoming and Montana would sell for $1.83 and $1.64 per ton, respectively. The capital costs for the strip mining of lignite range from $6.4 million for an output capacity of 1 million tons annually to $20.7 million for an annual capacity of 5 million tons. The corresponding selling prices of $3.01 and $2.12 per ton, respectively, Indicate the advantages of a large-capacity strip mine.

Jan 1, 1972

By C. E. Lapple

To improve mine health and safety conditions, there is need for a portable instrument that mine inspectors can use routinely for rapidly checking concentrations of dust in mine atmospheres. On October 23, 1969, Stanford Research Institute was authorized by the U.S. Bureau of Mines to conduct a study aimed at developing such an instrument under Contract No. H0100186. The results of that study are reported in Technical Report No. 1, "Development of Portable Instrument For Measuring Coal Mine Dust Concentration," August 1970. In that study it was demonstrated on bench-scale that a near-forward optical scattering device gives a linear correlation between mass concentration and optical readout over a range of 2 to 200 mg/m3 with excellent reproducibility. The same correlation was obtained for the Respirable* dust fraction of three different coal dusts within ± 10% and an extreme spread of ± 30%. Based on these results a prototype instrument was designed which was expected to meet all the necessary requirements of a portable instrument for mine use. Because of the excellent results obtained, a further study was authorized by the Bureau of Mines on May 10, 1971 under Contract No. H0111688. The prime objective of this study was to build, calibrate, and deliver to the Bureau of Mines two prototype instruments based on the design previously developed. The emphasis was to be on providing instruments which would meet certain minimum standards of size, weight, response time, sensitivity, ruggedness, reproducibility, permissibility, and cost (ultimate); optimization of the design was to be considered only insofar as it would not significantly delay the development. One instrument was to be delivered after initial calibration of both instruments with Coal Dust PGH. The second instrument was to be used for further calibration with a number of other coal and rock dusts and for assessing other relevant performance characteristics. This report summarizes all the results of this second study.

Jan 1, 1972