Search Documents

By R. H. Lee

WITHOUT doubt, one of the most frequent and serious annoyances connected with the practical running of a blast-furnace, especially in single-furnace plants, is caused by low steam, in spite of the fact that all boilers at blast-furnaces have grates for burning coal, and that coal is more or less continuously burned upon them, from three to a dozen men being pretty constantly engaged around the boilers as firemen or coal- and ash-handlers. At times, when the furnace is ? tight," all available men are put on to assist the regular firemen; yet sufficient steam cannot be got to keep the engines up to their regular number of revolutions, while the stoves, deprived of the gas which has been sent to the boilers, run cold, so that, when the furnace loosens-up and resumes the regular rate of driving, the blast is very considerably below normal temperature, and a.' cold," or at best a " high-sulphur," east is the result. Again, it often happens that a furnace, running at its best, becomes temporarily a little too hot; the pressure rises; the amount of gas made' is diminished; the steam soon commences to go down; and a small scaffold is likely to form before the furnace has been brought back to the proper rate of driving, and thus enabled to take its regular amount of blast. The usual remedy is either to "jerk" the furnace by a sudden, brief intermission in blowing, or to cool the furnace by lowering the heat of the blast; but if the lower blast-temperature be maintained too long, the hearth and descending stock may be cooled below the " critical temperature " mentioned by Mr. .Johnson, and the furnace may go to the other extreme, and become cold. This is especially the case when coal or coke, high in sulphur, is used:

Jul 1, 1906

By I. L. Bell

The ironmasters of America had asked the Iron and Steel Institute to visit the USA. The Council decided it was not possible to accept, but Mr. Bell visited; this is an account of his trip. Topics covered include transport, charcoal, coal measures, coal, anthracite, bituminous coal, flux, magnetic iron ore, specular iron ore, limonite, red hematite, clay ironstone, black band ironstone, smelting works, blast furnaces of Pennsylvania, Lake Champlain furnaces, Lake Superior furnaces, Cleveland furnaces, Pittsburg furnaces, Missouri furnaces, and those of the southern states. He goes on to describe Catalan hearths, malleable iron works, Bessemer works, the Blair steel process, and labour.

Jan 12, 1875

By J. B. Zadra

During the investigations of the occurrence of manganese in the western United States, the Bureau of Mines received a 100-pound sample of manganese ore from the Doyle-Smith property, Yuma County, Ariz. Laboratory tests were made to determine the amenability of this ore to standard ore-dressing methods of concentration to produce a marketable-grade product. The Doyle-Smith claims are in northern Yuma County, within 15 miles of the Artillery Peak deposit. The lot of ore used in the test work was taken from the outcrop of a large, massive, irregular bed of oxide manganese ore found on the claims.

Jan 1, 1952

By Thomas Camus

"STATE OF THE ART The current situation of ground prediction in TBM is of great concern for tunnelling contractors, and the subject has been quite widely addressed over recent years, for instance by the French Eupalinos 2000 programme, which tested a variety of technological approaches. A number of interesting projects were executed, such as the SOUND and OnSITE projects, part of the German Geotechnologien programme: these projects are focused on seismics, while other techniques such as radar are not considered. Little information and even less industrial applications have been released apart from lab simulations and numerical modelling. A number of field tests in different configurations have been carried out for compression waves, but the results were often not reliable or convincing, and therefore little has been reported in open literature. The advances seem somewhat promising as far as hard rock tunnels are concerned, but ignore the problem raised by concrete lined tunnels such as those bored by a TBM in soft ground. In such tunnels, sending and receiving seismic waves reliably through the lining (and the grouting behind) is quite illusory. A careful analysis of the seismic prediction research results show that the main problem is the source which is poorly controlled and poorly coupled (for instance in concrete lined tunnels, or in approaches that use the TBM cutter head vibrations as a source). Generating waves perpendicular to the tunnel axis is also a problem: aligning with the tunnel axis makes more sense. Radar (Ground Penetrating Radar - GPR) has been used in geotechnical surveys for decades, and also for tunnel inspection. Attempts have been made at using it on a TBM (for example in Japan by Taisei) but mainly using off-the-shelf GPRs, which are not adapted to work in the specific environment of a TBM (because of its huge mass of metal, to start with). Very few results have been published, probably due to the somewhat disappointing performance of such implementations. At present, no TBM has a GPR incorporated in its cutter head that is able to predict ground characteristics while drilling. Another characteristic and drawback of most current methods is that they require dedicated periods of time during which other tunnel construction activities must be stopped. Due to the duration of such operations this leads to performing ground prediction on a weekly basis only, and therefore to a requirement for an investigation range of 100 metres approximately (in order to cover the TBM advance over the coming week). This is not achievable with boreholes made from the TBM, even less if a reasonable accuracy is required, as is usually the case."

Jan 1, 2016

By P. K. Hofmeyr

Traditional fire assay dates back over 3000 years and has changed very little over that time. The only improvement is to replace the gravimetric finish with dissolution of the Precious Metal bead followed by AA or ICP analysis of the solution. The newly developed FIP A (Fast In-line Fire Assay) method allows full automation of the fire assay process from sample preparation to spark analysis of the Pb button. This results in fully quantitative analyses for Pt, Pd, Rh, Ru, lr, Au and Ag in typically less than an hour after a sample is entered into the system. Detection limits are theoretically Pt 0.08 ppm, Pd 0.002 ppm, Rh 0.002 ppm, Au 0.08 ppm and Ag 0.002 ppm but in practice the lower measurable limits are about double these figures. Few opportunities have been available to present data obtained using the FIFA system as all FIFA laboratories have been in the domain of a Pt mining company which prefers to keep all Pt analytical matters confidential. However, IMP has recently participated in the round robin exercise to establish recommended values for a new series of Merensky Reef and UO-2 Layer reference materials produced by African Mineral Standards. The precision of the results was excellent being on average Pt 2.05%, Pd 1.25%, Rh 4.08% and Ru 4.94% being expressed as Relative Standard Deviation. The excellent precision is a reflection of the efficient collection of POEs in the Pb buttons and the homogeneity of the Pb buttons. However, the accuracy was not as good. The poorer accuracy is interpreted as the calibration of the spectrometer not being as good as desired due to the difficulty in acquiring a suitable range of standards with reliable recommended values for the PGEs. The most recent spectrometer was calibrated with the greatest care and produced slightly better results for Pt, Pd and Rh and slightly worse for Ru.

Jan 1, 2014

By N. Vayenas, G. Yuriy

"The combination of a predictive reliability assessment model and discrete-event simulation can be an effective methodology to study the impact of equipment failures on the capacity of production systems in mines. In our case, a predictive reliability assessment model using genetic algorithms is combined with a discrete-event simulation model to analyze mine equipment systems.Discrete-event simulation involves modelling of real-life systems based on variables and events that occur or change at distinct points in time. The Simul8 simulation software, by Visual Thinking, is used in this research. It is a two-dimensional (2D), discrete-event simulation/ animation software tool for creating realistic depictions of manufacturing and materials handling systems.The simulation model developed for the purpose of this research represents a typical two-level, sub-level stoping section of an underground mine in the Sudbury region in Ontario, Canada. This 2D model was created to assess the impact of equipment failures to a mine’s production throughput. In more detail, using mean time between failures (MTBF) data of scooptrams derived from a reliability assessment model based on genetic algorithms, LHD failures are incorporated into the simulation model. These failures cause production interruptions to the development cycle and consequently loss of hauling capacity.Another purpose of this research work is to demonstrate how low-cost simulation tools such as Simul8 can be successfully applied to model underground hard rock mining operations. The research discussed in this paper is carried out by the Laurentian University Mining Automation Laboratory (LUMAL)."

Jan 1, 2005

By R. M. Kuralt

CONCESSION from the Chilean government granting the company use of the Rio Salado water stipulates that a minimum of 35,000 metric tons of such salty water must be diverted from the Salado daily, and be disposed of in a manner not to contaminate the Rio Loa to the east of its confluence with the Rio San Salvador at Chacance, Fig. 1. Consequently, the selection of a suitable site for the sulphide plant tailing disposal had the additional problem of the disposal of excess brackish waters. Studies of the terrain in the area directly to the south of the plant indicated that construction of tailing ponds would be costly, and generally unsatisfactory due to excessive slope of the ground, lack of flanking hills, danger of raising the groundwater level thus causing springs along the Antofagasta-Bolivia railroad; and the possibility of creating a dust nuisance at the plant site or at Calama due to blowing sands. Further to the southwest the San Salvador river canyon offered some possibilities and surveys were made at sites A to D, inclusive, Fig. 1. Here again costly dams would have been necessary to impound the tremendous quantity of tailing produced by the new plant, and provision would have to be made to handle a considerable flow of water through the disposal area to the west of the Rio Opache. Additional surveys were made in the area to the southeast of the plant which brought to light the existence of a natural basin of about 14 1/2 square miles, flanked by low-lying hills, and requiring only the most rudimentary dams to close the outlets at the western end. It has been estimated that the Salar de Talabre, as this basin is called, has the ultimate storage capacity of 1 billion tons of tailing with dam heights of only 60 ft. Pipe Line Layout After the decision had been reached to use the Salar de Talabre for the main disposal area various methods were considered for transporting the tailing from the 300 ft diam thickeners to the disposal site, 17.7 miles away. The first plan was to construct a. concrete launder on a 11 pct grade but a survey of this grade line indicated it would not lead directly into the Salar but would terminate somewhat to the north, and from that point on the slope would be considerably less than 1 pct along a natural watercourse. A slope of 2 pct or even 2 ¼ pct in such a rough watercourse or ditch is the ideal, judging from the success of operations at Cananea. Since a simple ditch is the most economical vehicle for the transportation of tailing, it was decided to use one with a 2 ¼ pct grade for as much of the distance as was possible with the existing terrain and to construct a concrete headbox, or forebay, at the terminus of the ditch to supply a steel pipe line leading the rest of the way into the Salar. Referring to the maps of the Chuquicamata area outlining the tailing disposal system, Figs. 1 and 2, one can trace the flow of the tailing from the thickeners to the Salar as follows: The 8-in. spigot pipes from the thickeners (1) discharge into a concrete sump feeding a concrete launder with a 2 pct slope. The launder carries the tailing into a concrete junction box (2) located south of the sulphide plant. The purpose of the junction box is to provide emergency facilities for diverting the tailing flow from the main disposal area to the emergency area. It also provides a junction point for the launder from the sulphide plant's future east extension. The box is fitted with a pair of radial gates controlling flow into the main tailing ditch (6) or the emergency ditch (3) which terminates on the pampa. All ditches are of the same cross section, namely 4 ft wide at the bottom with 1 : 1 side slopes and with a minimum depth of 21/2 ft. Where the nature of the ground demands it, the ditches are lined with stone rubble. The overflow from the plant's 10 million gal reservoir (4) is led into the main tailing ditch by way of a spillway ditch (5). The main ditch terminates in a trashscreen fitted, concrete forebay (7) which serves as a headbox for a 24 in. O.D. x 3/8 in. wall, Dresser coupled, steel pipe (10) and a 12 in. x 8-gage spiral welded, wedge-lock coupled, steel pipe (8). The forebay is fitted with two compartments, one for each pipe, and flow into each is controlled by radial gates. Each compartment is fitted with a 6-in. drain pipe controlled by a rubber pinch valve. To protect the forebay from the abrasive effects of the tailing, the sides of the compartments will be lined with old

Jan 1, 1952

By V. M. Troughton

Large diameter bored piles with grouted bases have been adopted for the foundations of the majority of the buildings at Canary Wharf in London's Docklands, including a deep basement car park. The piles are founded in the Thanet Sand which forms part of London's aquifer where water levels are reported to be slowly rising. A special pile test has been carried out to determine the effects of both the basement excavation and a possible long term rise in the groundwater level on the performance of base grouted piles. These effects were simulated by injecting water around the pile toe and thus reducing the vertical effective stress. In this paper the test layout and procedures are described and the results are presented. The test results showed that the reduction in pile base resistance under increased water pressures was less than predicted by conventional design methods based on vertical effective stress. The end bearing resistance was found to be proportional to the mean effective stress.

Jan 1, 1989

By J. A. Hansuld

"THIS SESSION marks something of a milestone in that it is, as far as I know, the first session at a CIM Annual Meeting devoted entirely to exploration geochemistry. This is an indication of the general acceptance and widespread recognition by industry of geochemistry in mineral exploration. As a first, I hope it proves sufficiently successful and interesting that geochemical exploration sessions will become a routine part of future CIM annual meetings. The greater use and acceptance of geochemistry has resulted in many investigations and advances, especially in areas such as the Canadian Shield. For a first session on geochemistry, the meeting in Quebec suggested an ideal opportunity to assess these advances and report on the current application of geochemistry in the Shield. The theme of the session is ""Geochemical Exploration in the Canadian Shield - The State of the Art."" A series of six papers will be presented dealing with the various dispersion media - rocks, heavy minerals, ""soils"", lake sediments, waters and vegetation. As a background to the individual presentations, I would like to take a few minutes to briefly trace the history of the use of geochemistry in the Canadian Shield."

Jan 1, 1971

By W. D. MOTTER

THE following brief description of the status of operations of the Chile Exploration Co. at Chuquicamata, Chile; and of the plant as it exists today, points out the-great progress that has been made since the initiation of prospect drilling in 1912. During the 11 years which have elapsed since then, a group of small mines, eking out a 'precarious existence, has been consolidated into one large operating property,, taking high rank among the world's producers of copper. After a drilling campaign followed by a construction period, the plant first started operations in 1915. Since then production has been gradually increased, as world conditions permitted, until the present status has been reached.

Jan 1, 1924

By K. Huttu, A. van Wageningen

"The Kittilä underground mine in northern Finland is extracting one of the largest known gold deposits in Europe. Kittilä achieved commercial production on May 1, 2009, becoming Agnico Eagle’s first mine to open outside of Canada. The Kittilä orebodies were initially mined from two openpits – Suuri and Roura – and underground operations were added in October 2010. The pits were mined out in November 2012, so mining is now entirely underground in the Suuri and Roura deposits. Additional, small openpits will mine any remaining near-surface reserves in the future.The Kittilä Mine is located in the Lapland region of northern Finland, approximately 900 km (560 miles) north of Helsinki and 150 km (93 miles) north of the Arctic Circle. With a mine life estimated through 2034, Kittilä is Agnico’s longest-life mine.The mine’s proven and probable reserves contain 32 Mt (4.7 million oz) at 4.6 g/t (0.13 oz/ st) gold. Ore has been mined from underground since 2010. The original 3 kt/d (3,300 stpd) operation underwent an expansion project to increase the throughput capacity of the mill by 1 kt/d (1,100 stpd), starting by the end of 2014.The region around the Kittilä Mine is underlain by mafic volcanic and sedimentary rocks of the Kittilä Greenstone Belt oriented nearly vertical. This greenstone belt is similar to those hosting Agnico Eagle’s Canadian deposits in Quebec’s Abitibi region and Nunavut. At the contact point between ironrich and magnesium-rich rocks lies a 100- to 200- m (330- to 660-ft) thick structural zone known as the Suurikuusikko Trend. This trend hosts the Kittilä deposit, where multiple mineralized zones have been traced over a strike length of more than 25 km (15 miles).Most of Agnico Eagle’s work has focused on a 4.5-km (2-mile) segment of the Suurikuusikko Trend that hosts the five main zones of the known gold reserves and resources. From south to north they are: Ketola, Etela, Suuri, Roura and Rimpi.The ore at the Kittilä Mine is refractory, making gold extraction relatively difficult because the gold is generally locked inside the two main sulfide minerals – arsenopyrite and arsenic-rich pyrite. Only about 4 percent is very fine-grained “free gold” (not locked in sulfide grains) and easier to extract. Most of this free gold is found in the outer, oxidized or eroded sections of the ore."

Jan 1, 2015

By I. L. Follington

This paper describes the research and development programme to develop a prototype underground auger mining system aimed at developing and demonstrating an underground auger mining system able to provide economic access to thinner (<1.8 m) coal reserves of South Africa. Data concerning the performance of modern coal augers under South African coal mining conditions were gained from a proven surface auger which operated across a range of coal types. These data were analysed and considered in conjunction with historical information regarding previous attempts at building underground augers dating back to the 1950s. Drawing on these data a prototype underground auger mining system, the BryDet BUA 600 underground coal recovery auger, was designed and manufactured by the BryDet Development Corporation in collaboration with Eskom and Cutting Edge Technology Pty Ltd with support from Anglo Coal and the Ingwe Coal Corporation Ltd. The prototype BryDet BUA 600 underground coal recovery auger commenced trials in March 2000 at the Matla Mine near Witbank in South Africa. The initial trials were undertaken in an open cut to facilitate the commissioning and training associated with a prototype mining machine. A total of 30 holes was augered in the box cut before the machine moved underground. The prototype BUA 600 first achieved the target penetration depth of 80 m in its third hole. The prototype BUA 600 is a new underground mining system which has passed early testing with ?flying colours? and could provide access to extensive underground coal reserves unmineable by conventional mining techniques both in South Africa and elsewhere around the world.

Jan 1, 2001

By H. L. Liu

With the exploitation of mineral resources, valuable minerals are more and more finer and poorer. Priority reclaiming liberation grind particle under rough grinding, will help to pervert loss of melts, raise dewatering efficiency of concentrate, reduce consumption of reagent. And it is propitious to reduce energy consumption and raise the utilization rate of resources. With the feature of coarse particle?s desorption and deposition, CLF flotation machine has special pulp circulating way, which is not only apply to treat coarse particle but also normal size particle. The paper advanced the history, the design principle, the structure feature and the application of CLF flotation machine.

Jan 1, 2014

By Roorda H. J, R. R. Saddington, Curlook W

THE copper-nickel sulfide ore deposits of the International Nickel Company of Canada, Limited contain the minerals pyrrhotite, pentlandite, and chalcopyrite. In the extraction of the nickel, copper, and iron, much of the processing involves oxidation of the metals as well as sulfur. Roasting plays a predominant role at several stages in the operations which prepare the constituent metals for refining. Copper, nickel and iron concentrates of various grades, ranging from low-grade nickeliferous pyrrhotite to high-grade nickel sulfide, must be partially or completely oxidized. Figure 1 shows the main points at which roasting is conducted at INCO. Roasting experience at INCO dates back to the time when lump ore was partially roasted in heaps. It has progressed through single hearth roasters, sinter machines, multiple-hearth roasters, flash roasters, and more recently has centered on the development and utilization of fluid bed roasters. The primitive, slow, and inefficient method of heap

Jan 1, 1961

By F. Carew

Accurate knowledge of what mass and grade is to hand and where it is stored is key to mine efficiencies and overall profitability. In order to make the right decisions and align production with stockpile capacity, feed and contract demand, a clear and accurate view from production through blending and processing is required. The use of a mine production management solution can provide you with a high degree of confidence in and visibility into validated data as well as auditable and traceable material movements, activities and surveys. A robust calculation engine enables mass and grade changes to propagate to material movements and stockpiles to ensure you are getting the most accurate view at all times. Tracked changes in material balances can be readily incorporated in revised production schedules to close the loop. The availability of accurate, timely information, coupled with predictive trend indicators, is a significant advance in narrowing the gap between claimed and planned production that is common to many mines, regardless of commodity. This paper provides an overview of a Mine Production Management System (MPMS) and explains how the system helps address the challenges listed above.

Jan 1, 2011

By G. Watson, S. Sawyer

A Method to Calculate Hydrodynamic Loads on Underground Bulkheads Bulkheads are structures built in openings in underground mines to impound water, preventing the water from entering the active mine workings. These structures not only have to be designed to withstand the static, hydraulic pressure, but also the dynamic or seismic pressure, which would be generated by an earthquake. Bulkheads can be considered underground dams. Unlike dams on the surface, bulkheads are often subjected to hydraulic heads that exceed the heights of the bulkheads. Theodor von Karman in 1933, and Westergaard earlier, developed the equation by which the hydrodynamic pressures on surface dams could be calculated. Civil engineering handbooks of today contain this equation. In this paper, using the methodology developed by von Karman and Westergaard, the authors have developed an equation by which the hydrodynamic forces on bulkheads could be calculated when the hydraulic head exceeds the height of the bulkhead.

Jan 1, 2007

By A. T. Yu, K. A. Young, Ronald M. Hays, Sanford Terry, D. R. Campbell, J. K. Lovrien, W. L. Price, C. W. Matthews, W. R. van Slyke, S. P. Cole

Storage and transport systems are essential for mineral processing. Section 10 includes systems for storage and transport of dry bulk materials, slurries, and water necessary for operation of mineral pro¬cessing plants. All aspects of these systems are presented, including material characteristics; dry material placement in and reclamation from storage stockpiles and bins; dry material conveyance; hydraulics (liquid flow and pumping); slurry characteristics; slurry storage and reclaim, slurry flow (distributors, launders, and pipes), and pumping; water (primary and secondary process, reclaimed, fire, cooling, and domestic) supply, transport, and storage; equipment selection and sizing; power transmission; controls; and health and safety. The mate¬rials considered include crude ore; process and other water supplies; initial, intermediate; and final in-plant materials; finished materials; and tailings and other waste products. Section 10 is a compilation of practical operating data for engineers, technicians, and plant opera¬tors. For the design of mineral processing plants, including selection and sizing of equipment, the design engineer should consult with equipment manufacturers, suppliers, engineering firms, and plant op¬erators with specialized experience in particular materials handling methods. When unusual conditions are encountered, actual pilot or full scale testing may be required to insure adequate design. Operation of mineral processing plants is dependent on the proper engineering and construction of storage and transport systems for dry bulk materials, slurries, and water. It is obvious that processing plants cannot produce the required quantities of semifinished and finished products unless these material can be transported adequately to, through, within, and from the plant. Costs of storage and transport systems may exceed 50% of the total capital and/or operating costs. Considerable attention must be given to the design, layout, and engineering of these systems. These systems are interrelated with the mineral processing method and it is necessary to determine the best combination of mineral processing method and storage and transport systems. Storage and transport systems perform a major supportive func¬tion to mineral processing. The final selection of these systems depends on the final selection of the processing method and related systems (environmental control, tailings and waste disposal, etc.). The process¬ing method determines the characteristics of materials to be stored and transported; distances, elevations, flow rates for transport; and storage requirements. Flowsheet After selection of the processing method and related systems, a flowsheet must be developed. This flowsheet should indicate produc¬tion rate, percent solids or moisture, and specific gravity for all initial, intermediate, and final products or product flow streams. It also may be necessary to know the size analysis, chemical analysis, abrasiveness, and other physical characteristics of various product flow streams. The flowsheet provides basic information for plant layout, storage requirements, and selection and sizing of process and transport equip¬ment. Storage and transport systems often function improperly be¬ cause of inadequate flowsheet data or process revisions, resulting in improper equipment selection and sizing. Further details on plant design are presented in Section 33. After selection and sizing of process equipment, it is necessary to select the type of material transport equipment to be used for in¬plant materials handling as well as crude ore, tailings, and final prod¬ucts. The storage and/or surge requirements, including capacity and location, then are determined. Storage and/or surge capacity is neces¬sary for leveling production rate fluctuations due to variations in material characteristics; production scheduling; equipment mismatch¬ing, failure, or breakdown; and scheduled maintenance downtime. Variations in ore grindability will cause fluctuations in throughput or production rate for grinding mills and variations in ore grade will cause fluctuations in production rate for concentrating equipment. Variations in material moisture content and percent solids can have serious effects on the capacity of material transport equipment. In some cases, a blending system may be desirable or necessary to reduce variations and to obtain uniform production and/or metallurgy. Storage capacity often is needed because of different production schedules for various phases of the mining and mineral processing complex. As an example, the mine and coarse crushing plant may operate on a one- or two-shift-per-day schedule while the fine crushing plant and concentrator on a three-shift-per-day schedule. This would require storage between the coarse and fine crushing plants. Another example would be load-out storage where unit trains are used to haul concentrate or final products. The concentrator could be operated on a three-shift-per-day schedule while only I to 2 hr may be scheduled for unit train loading. This would require adequate load-out storage so that the concentrator can be operated continuously. Process equipment with mismatched capacities requires storage or surge capacity between the mismatched equipment to achieve oper¬ating efficiency. As an example, the fine crushers may have greater capacity than the rod mills. Storage between the fine crushers and the rod mills permits both the crushers and rod mills to be operated at optimum capacity with the crushers actually operating or running a lesser number of hours per day. Mismatched capacities for process and transport equipment also may require storage or surge capacity. Mismatching of equipment capacities most often occurs because of the difficulty in equipment sizing. Thus, the design engineer must anticipate where in the flowsheet these mismatching capacities are likely to occur while making every effort to assure that equipment is selected and sized properly. Equipment breakdown can cause major operating difficulties and lost production. These breakdowns can be reduced with adequate scheduled maintenance. Lost production due to nonscheduled down¬time caused by equipment breakdown can be reduced further by standby equipment and storage and/or surge capacity ahead of essen¬tial mechanical and electrical equipment. As an example, standby pumps and conveyors often are available as part of the in-plant trans¬port system. Storage and/or surge bins and tanks often serve dual functions, such as dewatering, mixing, and smoothing production rate fluctuations.

Jan 1, 1985

By G. A. Grandy, P. F. Thomas, C. D. Danecki

When considering the mill drive system for a grinding application, a large number of questions must be answered. Depending on the mill size and type, the mill can be driven by several configurations of drive systems: a single low-speed motor connected to a pinion driving a ring gear, two low-speed motors connected to two pinions and driving a ring gear, or a gearless motor mounted directly. In addition, a gear drive system can have a reducer placed between a high-speed motor(s) and pinion(s) or a power path splitting pinion stand. In some designs the reducer is integral with the pinion stand driven by a high-speed motor. The technical and commercial implications of several mill drive options are presented. Initial cost, cost of installation, cost of commissioning, and cost of operation and maintenance are presented for each drive option considered. The impact of each drive system on the design, cost and operation of the overall plant electrical system is discussed. Also, consideration is given to mill drive availability, and the potential cost resulting from delays in plant production.

Jan 1, 2001

By John A. E. M. Church

THE prospector&apos;s pan was the first implement used for saving gold, and its action is so effective that it has never been equalled for thorough work. Copper plates, blankets, sluices, and amalgamators of several patented designs have thrust it aside, but in spite of all the advances made there is no dispute among experienced men as to the comparative thoroughness of the work done by it and its rivals. When its rivals are doing their best, the pan can take their discarded refuse and prove their inefficiency by producing from it not only gold, but even the mercury which has been lost from the machines themselves. The trouble with the pan has always been that it was only a tool. Man was the machine that moved it. His work was high-priced, the quantity treated small, and it was impossible to use the pan for any but the richest sands. As a consequence the best gold-saving appliance known has been discarded for years and replaced by machines of inferior excellence, but which could more than make up for their limited ability in saving gold by their capacity for treating great quantities of ore. Mr. Peck is one of the old-time amalgamators of the Comstock district, and the first idea of the new machine came to him as he used to pan below the tailrace of his mill. No matter how fine the work of the mill was, the pan invariably proved that better could be done. The tailings always contained gold, silver, and mercury. This state of things is just as true to-day, after all the improvements that have been made, as it was then, and the much-vaunted method of the " Washoe process" consists in extracting 72 per cent. of the gold and silver by one operation, and then repeating this operation half a dozen times to get out about one-third of the remainder. With all the advances of twenty years in milling, there is nothing more crude in metallurgy than the treatment of tailings in many of the large mills of the West.

Jan 1, 1880

By S. Coats, G. Norton, A. Benham, P. Ková

The Aynak copper deposit, located 30 km south of Kabul in Afghanistan (Figure 1), was discovered by Soviet geologists in the 1970s. Extensive exploration undertaken in the area between 1974-80 included several hundred boreholes, seventy trenches and nine exploratory adits. This work identified a “drill-indicated resource” of 240 Mt at 2.3% Cu (ESCAP, 1995).

Jan 1, 2007