Search Documents

By Patricio Vergara Lara, Jorman Barrera

The selection of the production level elevation is one of the most critical strategic decisions faced by large-scale block or panel caving projects. This elevation largely affects project timelines, capital expenditures, resource recovery, and may even constrain the mine’s maximum production capacity. Over the years, many computational tools have been developed to assist in this decision, most of them based on the same principle of maximizing the project value given its production level elevation. However, for large and inclined deposits, or those extending significantly in the vertical dimension and where extraction cannot be achieved from a single level, traditional selection techniques involving multiple production horizons often lead to suboptimal results. This paper proposes a methodology ensuring that the selection of production level elevations in a multiple horizons (“lifts”) case is globally optimized. Input parameters include economic and cost variables, maximum extractable column height, and deepening costs. The methodology is demonstrated through a real case study to illustrate its potential impact on project value.

Feb 22, 2026

By J. H. Soulé

This information circular is one of a series published by the Federal Bureau of Mines describing methods and costs at various mining operations. The Schwartzwalder uranium mine, situated about 20 miles west of Denver, Colo., is an important source of uranium ore in the Front Range. Production was begun in 1953, and nearly 36,500 tons of ore had been shipped by September 1, 1958. The mine is operated by Denver-Golden Oil & Uranium Co., Denver, Colo. Much interest has been shown in the property since uranium mineralization tit was found by Fred Schwartzwalder in 1949. The Atomic Energy Commission, Federal Geological Survey, Office of Minerals Exploration (formerly Defense Minerals Exploration Administration), and Federal Bureau of Mines have done work in the area, and various private concerns have shown interest in the property.

Jan 1, 1960

By S. Anderson

Advances in inexpensive computer automation led to the development and utilization of a computerized ore control system at Cyprus Coppers tone Gold Mine near Parker, Arizona. These new ore control practices improved accuracy, performance, and productivity of the ore control effort. An automated system for data collection, including bar coding of blast hole samples, laboratory analysis, data management, grade estimation, cut delineation, and ore zone stakeout, plays a major role in ore control practices. This is of particular interest because of the large amount of blast hole information being processed, analyzed, and reported daily.

Jan 1, 1991

By R. Kahrger

This paper is written to convey the latest developments in compact bucket wheel excavators (BWE's) operating in medium-hard rock and will serve to indicate that BWE and compact machines in particular do in fact have application in materials other than loose sandy soils and soft rock. A recently run extensive three month field test in hard marl, which was previously considered too hard and difficult to be handled by a BWE, is used as an example to explain some of the design requirements and problems associated with digging harder materials.

Jan 1, 1990

By J. S. Becker

Technology developed and first implemented in the United Kingdom enables very low grade aluminum scraps containing oils, organics, plastics and ferrous metals to be directly charged, without pretreatment, into a unique melting furnace. The system has been in full scale production for four years. The oxy-fuel-based furnace design incorporates internal afterburning in the furnace's hot zone, producing excellent thermal efficiency and very low emissions. The furnace is inherently low in NOx. This paper will provide both theoretical background and extensive operating results for this new melting concept. Applications describing both purpose built new furnaces and retrofits of existing reverberatory furnaces will be presented. Extensive operating emissions data will be presented.

Jan 1, 1997

By E. Keskinkilic

"Electrical steels are used in motors, power generators, and transformers for electrical applications owing to their superior magnetic properties. These properties are attributed to the presence of a significant amount of silicon in the steel composition. Silicon steels are mainly grouped into two categories: grain-oriented (GO) and non-grain-oriented (NGO). The Si content of silicon steels is generally between about 0.50% and 6.5%. Therefore, silicon steels are further classified as low-, medium-, and high- Si steels. In this paper, liquid steel processing practices for certain silicon steel grades are outlined by considering a steelmaking company that integrates a basic oxygen furnace (BOF), a ladle furnace (LF), and an RHtype degassing unit (RH). Possible problems are identified, suggestions are discussed, and conclusions are drawn on the basis of real plant data. IntroductionSilicon steels are widely used in motors, power generators, and transformers for electrical applications owing to their superior magnetic properties. They are mainly grouped into grain-oriented (GO) and non-grain-oriented (NGO) silicon steel grades. However, the differences in the properties and thermomechanical production of GO and NGO grades are outside the scope of this paper. In this study, liquid steel processing of certain silicon steels will be discussed. In the integrated iron and steelmaking process, converters are the primary steelmaking units that are used mainly for decarburization and removal of phosphorus, and for obtaining liquid steel with a specific chemical composition and suitable temperature for secondary steelmaking operations. Ladle furnaces are a type of ladle metallurgy station consisting of electrical and/or chemical heating facilities for adjusting the liquid steel temperature during alloying. Various types of vacuum units are used for decarburization and removal of nitrogen, hydrogen, and sulphur, depending on the metallurgical conditions of the vacuum units. In this study, an actual steel-production company is considered in which the primary steelmaking operation uses a basic oxygen furnace (BOF) converter with N2/Ar bottom blowing, and the secondary steelmaking operations involve (1) a ladle furnace (LF) heated by three graphite electrodes and equipped with Ar and N2 top/bottom mixing facilities, and (2) an RHtype (circulation) vacuum degassing unit equipped with a top-blowing attachment for oxygen blowing and an Ar-purging system from an up-leg snorkel."

Jan 1, 2018

By Joseph L. Condon

High-speed movies were taken of crater experiments in two-dimensional plates of Tennessee marble to study craters being formed primarily by stress-wave action. The contribution of gas action to the cratering process was minimized because the two-dimensional models did not contain the expanding gases from the explosive. Four burdens were studied for solid plates and one burden for a segmented plate. After cratering, the plates were reassembled for dye penetrant studies of fracturing. Flyrock velocities were calculated and related to the degree of fracturing, and compared with those from quarry shots. In general, the smallest burdens produced the highest flyrock velocities and the least amount of fracturing. Flyrock velocities compared favorably with initial flyrock velocities in quarry blasts, but did not show step accelerations due to gas effects as did the quarry blasts. The test with a segmented plate was used to simulate cratering in a jointed material and showed that stress-wave effects can be important for crater formation in jointed rocks.

Jan 1, 1972

By B. Rai

Aluminum is produced by the Hall-Héroult process, which involves passing a current through a molten mixture of alumina dissolved in cryolite (Na3AlF6) to reduce the alumina to aluminum. This process occurs in an electrolytic cell comprising a steel shell lined with a carbon cathode and refractory bricks. After a certain period of operation, the carbon cathode deteriorates and is removed from the cell along with the refractory bricks. These removed materials are referred to as spent pot lining or ?SPL?. Typically, 30 Kg of SPL waste is generated for every ton of Aluminum produced. Globally aluminum smelters produce more than 500,000 tons of SPL each year. Even though SPL has a high fuel value (8000 to 9000 BTU/lb) and contains valuable metals, it is classified as a hazardous material due to its cyanide content and leachable fluorides. Various disposal/recycle techniques have been developed over the years for SPL but none of them is satisfactory. Thus, large quantities of SPL are still being dumped in landfills. In some countries, even the land filling of SPL is not permitted. The safe disposal of SPL thus remains a challenging problem to the aluminum industry and the search continues to find methods of converting SPL into a non-hazardous waste and/or recovering the valuable materials contained in the SPL. We have developed a process to produce hydraulic setting cements (eco-cement) containing a novel fluoride rich cementitious phase, from SPL by an energy efficient, low temperature clinkering route. A raw mix blend of SPL, lime/limestone, calcium sulfate and tailings sands based on a set of design criteria developed by us, is clinkered in a two stage process; 2 hours soak at 800 °C followed by clinkering at 1000 °C for another 2 hours, to produce a soft clinker. The SPL eco-cement is made by grinding the clinker to a fineness of 5000 cm2/g Blaine with 1% by weight borax as a set retarder. A good quality cement having as high as 20 % by weight of SPL in the raw mix (28 % by weight in the cement clinker) is thus produced. The physical properties of the SPL cements are found to be comparable to the Indian standard (IS) specifications for Ordinary Portland Cements (OPC). We have produced the cement in a few Kg batches and tested the reproducibility of results from batch to batch for further scale up. Once commercialized, this process has a potential of converting SPL into value-added cement products. Keywords: cement, spent pot lining, clinkering, fluoride, aluminum, ordinary portland cements

Sep 1, 2012

By D. Lansburg

Electronic detonators are increasingly being used in today’s blasting in quarries, seismic, surface and underground mines. Electronic detonators offer several distinctive features over electric and non-el (shock tube) detonators including better timing accuracy resulting in excellent fragmentation and vibration control, field programmability and digital safety means. Because of the prerequisite electrical communications between the electronic detonators and the blasting machine, the layout or hook-up of these detonators can play an important role in obtaining the communication fidelity.

Jan 1, 2011

By Lorrie Fava

Two needs in the mining industry, to enable overall process improvements, are open systems and network connectivity in underground mines. The Pando project, a collaboration between Symboticware, Vale and Xstrata Nickel, and supported by CEMI, addresses these issues, and leverages the solution platform to deliver intelligent applications. An open system is one that uses publicly available standards for its key interfaces. Vendor-neutrality and ease of information flow are two main benefits that result from the use of open systems. By facilitating the interoperability of systems, open systems allow information to be available when and where it is needed for decision support. Network connectivity in underground mines is typically limited, with hotspots in strategically chosen areas that are relatively static. Mobile equipment moving through a mining work cycle experiences intermittent connectivity; in this situation, seamless remote equipment monitoring is impossible. The Pando project establishes an open technology platform, adhering to the IREDES and OPC UA standards. It enables the collection and integration of information generated by mobile equipment? seamlessly while there is a network connection, and as a store-and-forward gateway to manage intermittent connectivity. The platform capabilities are leveraged to support embedded intelligent applications. This open platform, the SymBot, is a rugged hardware and software device. The platform complies with open standards for industrial automation and systems interoperability. The SymBot platform is capable of providing advanced real-time decision support at the device level, and is designed to be remotely configurable. Applications being developed through the Pando project include engine monitoring, a dynamic load weighing system, machine location monitoring and automated activity monitoring including production and maintenance reporting.

Oct 1, 2010

By Michael Sheedy

Sulfuric acid is widely used as an electrolyte for the electrorefming and electrowinning or metals. Impurities in this electrolyte are controlled by continuously bleeding solution from the tank house. In addition to the contaminant these bleed streams contain high levels of sulfuric acid and the metal being recovered. Subsequent treatment of these bleed streams often requires neutralization which generates large volumes of solid waste. Absorption resin technology employing a novel ion exchange technique known as Recoflo® allows the separation of the mineral acid from dissolved metal salts. The recovered acid is suitable for recycle back to the electrolyte circuit. The metal salt and other contaminants leave the process free .of the sulfuric acid. In this process, known commercially as the APU®, ion exchange resin is used to sorb sulfuric acid while excluding the metal salts. The purified acid is then removed by washing the resin with water. The process has been extensively used for the recovery of waste pickling acids in the steel industry and anodizing solutions in the aluminum industry. In the mining and metallurgical industries the process has been successfully evaluated for the separation of excess sulfuric acid from copper electrolytes, the removal of magnesium and manganese contaminants from zinc electrolytes, and nickel and copper from copper electrolytes. A full scale installation on a copper refinery bleed stream at Palconbridge's Kidd Creek plant in Timmins, Ontario has now been operating successfully for more than 1 year while pilot field trials have been successfully completed on other applications.

Jan 1, 1997

By J. J. Taute, S. J. Archer

"BASF Mining Solutions has developed a new-generation copper solvent extraction reagent that offers significant benefits over standard extractants currently available to the industry. As the name suggests, the new hightemperature (HT) extractant can be used at a higher operating temperature, but also exhibits significantly lower degradation rates, greater copper-toiron selectivity, and is totally nitration-proof compared with the standard extractants. Pilot-plant trials have also shown that lower aqueous-inorganic entrainment can be achieved. This paper investigates the technoeconomic benefit of using the HT extractant as an alternative to the standard extractant in a high-temperature application. The results of the technical evaluation showed that the use of the HT extractant reduces the extractant addition requirements and bleed volume from copper electrowinning; this smaller bleed requirement further reduces acid and limestone consumption, leading to a reduction in valuable metal losses. The results of the economic evaluation showed that the use of the HT extractant represents significant cost savings over that of the standard extractant. IntroductionCurrent solvent extraction (SX) reagents employed for the extraction of copper from typical pregnant leach solutions (PLS) at ambient conditions function well with minimal long-term effects on the extractant’s performance (Taute et al., 2015). This performance, however, deteriorates at elevated temperatures due to the degradation of the reagent’s hydroxyoximes. The degradation mechanism, acid-catalysed hydrolysis of the oxime, is accelerated by high temperature. This has a knock-on effect where the increase in degradation products increases the organic viscosity, leading to increased entrainment, crud formation, and ultimately to an increase in SX reagent consumption (Bender, Emmerich, and Nisbett, 2013).SX reagents also show an increase in the co-extraction of iron as the ferric concentration in the PLS increases. Co-extracted iron is transferred to electrowinning (EW) during stripping of the loaded organic and can adversely affect EW current efficiency. Iron in the EW circuit is typically managed by bleeding the electrolyte; however, this can lead to excessive consumption of EW reagents such as acid, cobalt, and mist-eliminating surfactants. The electrolyte bleed can also affect upstream consumption of reagents, such as lime, due to the high acid concentration recycled to leach."

Nov 1, 2018

By Pia-Maria Haselberger, Marc Schiemann, Christian Frühling, Nicolas Richter, Hendrik Wehner, Andreas Kaschube

"The paper provides the principle considerations for a novel vehicle class within the scope of the project Large Modifiable Underwater Mothership (MUM). The main idea for these ships is to create a highly modular building block system for the global layout. This building block system allows for a mission-dependent module assembly. For the purpose of deep sea mining for example, the range of tasks reaches from multipurpose transportation and exploration missions to supporting tasks in up to 5000 m depth, e.g. energy supply. Topics covered in this paper are related to potential missions for these vehicles, the modular layout and the structural layout of a separate block module. The paper closes with a conceptual design example for this class.Index Terms—MUM, UUV, underwater mother ship, autonomous underwater vehicle, modular, deep sea, conceptual designI. INTRODUCTIONAs one of the leading economic nations, Germany is in need of energy and raw materials. In the 21st century, marine resources are a prominent and promising alternative to land based resources. However, there are challenges that need to be considered. Rough and often poorly plannable weather conditions prevail distant to the marginal seas. Ice coverage makes offshore services inefficient and costly in Polar Regions. The average ocean depth of 3500m and the associated environment conditions cause difficulties in fulfilling tasks in the deep sea. The project Large Modifiable Underwater Mothership (MUM) [1] will enable more efficient solutions in order to accomplish undersea duties and services in harsh conditions.This joint project comprises workshares from Atlas Elektronik, EvoLogics, thyssenkrupp Marine Systems, the University of Rostock and the Technische Universität Berlin. The principle idea of the project is the conception of a novel vehicle class. With highly modular autonomous underwater vehicles, this class will be capable of undertaking a variety of different tasks. Classically engineered vehicle structures will be split into single basis modules which can be flexibly assembled with specialized mission modules to form potent systems for individual assignments. The group of basis modules consists of units for navigation, vehicle control, propulsion and energy generation via fuel cell technology. The potential reusability of system relevant modules leads to a significant cost reduction and to shortened development periods compared with conventional vehicle concepts. The integration of newly designed additional mission modules is possible with little effort and a separate commercialization of single modules is feasible."

Jan 1, 2017

By O. A. Bascur

Several new hydrometallurgical plants have been built in the past years, new processes and equipment as well as advanced process control systems are being used to deal with the increasing requirements of safety, quality and production. Plant Information Management Systems are now being recognized as a key infrastructure component of the plant, giving the management, the operators, process engineers, finance, maintenance, and regulatory agencies an integrated view of the operation and providing the links for the (increasingly) multidisciplinary organization. This paper reviews several implementations of Plant Information Systems; real time performance management infrastructure examples are reviewed as a key component of business strategies, such as Mine to Port Planning and Supervision, Metallurgical Mass Balances, Solvent Extraction Composition Statistical Process Control, methods to minimize organic losses, reduce variable costs and to improve metal extraction. Several examples are provided to illustrate how companies are using the real time and historical information from assets and metallurgical processes to enable and empower people to improve the operations quality, safety and throughput, as well as continuous improvement and innovation initiatives.

Jan 1, 2007

By Emil Szaks

[A great number of papers have been presented at various Engineering Society meetings on the Unit Train subject. Moat are descriptions of facilities that have been constructed or are abort to be built. Many describe the facility as being the World's fastest, newest, largest, incorporating the latest technology and so forth, Many are duplications of installations that have been recently constructed, sort of carbon copies but perhaps arranged differently. The trend has been to incorporate loop tracks, rotary dumpers, indexers and, of course, the snivel coupler equipped unit train. How that the energy crisis has increased the use of coal, there has been a tremendous Increase in applications for permits to construct rail to river coal loading facilities. This paper is different. It does not describe any single existing facility, but is given to alert prospective terminal owners and engineers that there are items that require considerable study and evaluation beside merely selecting an indexer, car dumper, stacker, ship or berg loader and so on. An important item is the selection of the railway car which in turn can affect the selection of the method of loading and unloading. Let us list a few of the items that should be considered and discuss the areas that require examination:]

Jan 1, 1979

By Jae-Chun Lee, Sadia Ilyas

We investigate the technical feasibility of bioleaching of metals from low grade sulphidic ore. Experiments were conducted with an adapted consortium of Sulfobacillus thermosulfidooxidans and Thermoplasm acidophilum in batch bioreactors (1.5 L), small columns (10 kg ore load, 8 % S0 sludge) and large columns (80 kg ore load, 12 % S0 sludge). Approximately 83 % Ni, 85 % Cu, 55 % Fe and 81 % Zn was leached out in batch mode while 93 % Ni, 89 % Zn, 81 % Cu and 65 % Fe was leached out in column reactors. Bioleaching potential improved by acid pre-leaching, adaptation of microbial consortium and periodic bleeding of effluents.

Jan 1, 2014

By Matt Kilburn, Liming Lu, Steve Suthers, Alexander Edenton, Rodney Smyth, Matt Adam

"Magnetite concentrate is naturally good for pelletising. However, due to the depletion of reserves of traditional high grade hematite iron ore worldwide, the usage of magnetite concentrate in sintering is expected to increase substantially. Magnetite concentrate is typically high in Fe grade and releases extra heat when oxidised to hematite. This will not only improve the quality of agglomerates produced, but also have a potential beneficial impact on the fuel consumption of the agglomeration process. There are an increasing number of magnetite projects currently being considered and developed. However the concentrates from some of these projects are too coarse as pellet feeds and much finer and denser than normal sinter feeds. Accordingly, special strategies are required in order to utilise the coarse magnetite concentrates at high proportions in pelletising and sintering. This paper discusses various raw material preparation technologies and blending optimization methods demonstrated to be effective for improving the sintering and pelletising performance of coarse magnetite concentrates. Pre-granulation and addition of binders, such as hydrated lime, were found to be particularly efficient in recovering the sintering productivity of sinter blends containing magnetite concentrates. In pelletising, HPGR (High Pressure Grinding Rolls) grinding enabled production of good quality pellets from 100% magnetite concentrates and optimized blends containing up to 70% magnetite concentrates also formed good pellets.INTRODUCTION Magnetite concentrates are often used as feed materials for pellet plants or sinter plants depending on their grades and grain sizes. To achieve the required quality of green and fired pellets, the concentrates often need to be ground very fine (80% passing 38- 45 m), which inevitably consumes a great amount of energy. Therefore, efficient grinding processes are required to reduce the amount of energy consumption needed to achieve the sizing and chemical specification of pellet feeds. The use of magnetite concentrates in sintering has the potential to improve sinter chemistry, which is deteriorating over time due to the slowly decreasing grade of direct shipping iron ores around the world (Yang and Mathews, 1997; Yang and Witchard, 1998, Yang and Davis, 1999; Yang 2005). However, methods are required to allow the utilisation of high levels of concentrates in sintering while maintaining productivity and sinter quality (Han and Lu, 2017)."

Jan 1, 2018

By B L. Sommerville

"The theme of this International Mining Geology Conference is ‘Setting New Standards’. Rio Tinto’s iron ore operations include a complex integrated supply system to deliver ore from 15 mine operations through four independent terminals over 1700 km of rail line. Significant growth in the past 20 years has seen production grow from 88 Mt in 1997 to 329 Mt for the 2016 calendar year.With more than 50 years of mining in the Pilbara, Rio Tinto has extensive experience in developing standardised approaches to mine geology and the geometallurgical prediction of product quality to meet the increasing growth profile and business planning complexity.Rio Tinto’s standardised approach to mine geology can be developed and utilised on a daily basis to enable the optimisation of the supply chain in terms of tonnages and product quality. This experience demonstrates a fully standardised system can balance the needs of a systematic process across all mine sites and the flexibility for mine geologist to determine and use local properties at each mine; this is done by ensuring two key principals are in place: a single, centrally maintained, system is established and maintained, providing a common set of processes and software across all mine sites the system allows senior mine geologists to review and customise key attributes and product regressions, ensuring site specific data is used in product predictions.The benefits of formal work process and standardisation include health, safety and environment, people and skill development, cost and improved communication. Also product predictions from mine geologists are one of the key inputs into an integrated and dynamic mine to ship scheduling system, optimising the supply chain whilst still managing the product quality. The experience of Rio Tinto is that a standardised approach to mine geology is an enabler of value for the iron ore operations.CITATION:Sommerville, B L, 2017. Mine geology standardisation – providing the foundation to consistent short-term geometallurgical product predictions in a complex multimine and supply chain environment, in Proceedings Tenth International Mining Geology Conference 2017, pp 13–20 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 20, 2017

By M. R. MacIver, M. P. Pawlik

"An image analysis method based on chord length distributions is applied to the batch settling of polyacrylamide flocculated kaolin suspensions. Two features of the interaggregate void space, the void chord length distribution mean and the white-to-black distribution ratio are extracted from an image series obtained over the two hour settling experiments. This approach produces three signal values, from two different probability distributions that can be measured as an indication of underlying sediment bed density and aggregation state. Further work is required on the physical interpretation of the signal, the image acquisition conditions, and the parameter selection methods. It is suggested that this chord length based feature extraction technique may be a useful signal to monitor during batch settling or thickening.INTRODUCTIONFew in situ techniques are available that can be used to directly measure aggregate properties within sediment beds in thickeners or secondary settlers. Typical process variables monitored include rake torque and height, bed level and pressure, feed rate and density, underflow rate and density, settling rate, and overflow turbidity; yet these process variables are only weakly related to process dynamics (Concha et al. 2014). Additional process monitoring signals, based on the direct measurement of aggregate properties could improve solid-liquid separation control and allow the extraction of more detailed information from batch settling experiments.Several optical methods exist for measurement of moving suspensions of aggregated solids in the dilute concentration regime, such as focused beam reflectance measurement (Peng and Williams 1994), and the turbidity fluctuation method (Gregory 1985). In the more concentrated region of a thickener, acoustic backscatter penetration and attenuation measured with an acoustic probe and changes in the underlying solid concentration in the highly concentrated, near-bed region of a thickener as a function of height and time (Hunter et al. 2012). While machine vision for froth monitoring has been thoroughly studied with at least five commercialized technologies (Aldrich et al. 2010), its’ application to the study of thickening has been limited."

Jan 1, 2016

By R. ZapataN.

"In the following report, Altonorte Smelter owned by Xstrata will explain its experience with its denominated furnace called ""Continuous Altonorte Reactor"" since started up in March 2002. The Reactor is the main and only smelting furnace since the operation of Reverb Furnace was stopped (15 days after the start up of the Reactor) and it can be operate with dry concentrate for injection by tuyere and wet concentrated via Garr Gun when the injection system fails. From the started up of the Reactor, three operational campaigns have been carried out where in each one they have been increased their smelting throughput and availability. The flexibility reached by the technology bath smelting has allowed a high level of smelting of concentrate and revert materials. The high availability of the Reactor and overcoming problems that were considered of high complexity like the extraction of white metal and slag, refractory campaign, etc. has allowed the Altonorte smelter to project to smelting 1,200,000 tonnes per year with its only Reactor in next year."

Jan 1, 2007