Search Documents

By R. Angulo

Carbon nanotubes (CNTs) have recently emerged as materials with outstanding properties. This has promoted their consideration as reinforcements for other material systems, such as ceramics. However, one of the fundamental problems with producing CNT-reinforced ceramics is the effective dispersion of CNTs during processing. This has been successfully carried out recently using organic solvents. This paper is a preliminery investigation into the rheological behavior of aqueous CNT-alumina slips, with the objective of moving towards a more environmentally friendly aqueous tape casting process for the production of CNT-ceramic composites.

Jan 1, 2008

By C. G. Anderson

Throughout the world, there are many orebodies or materials which have significant value but also contain arsenic. As regulations on the transport, exposure, disposition and emission of arsenic have become more stringent; it has become increasingly more difficult to derive the values from these resources. This paper will outline the fundamentals of alkaline sulfide hydrometallurgy and its successful application to arsenic bearing ores, concentrates and materials.

Jan 1, 2005

"10.1. IntroductionAs discussed by Westland (1981), the six platinum-group elements (PGE) belong to the Group VIII transition metals, to which iron, nickel and cobalt also belong. The chemical similarity between these nine metals accounts for the fact that they tend to be concentrated together as a result of geological processes. These processes started to effect the distribution of these metals at the very beginning of the earth's history.The first line in Table 1 gives the concentration of nickel and certain other Group VIII transition metals in carbonaceous chondrites, those meteorites with a composition that is believed to reflect best the composition of our planetary system apart from hydrogen and helium. The second line is the estimated concentration of the same elements in the earth as a whole. It is seen that these two estimates are quite similar, the earth being perhaps 2 to 3 times richer in these particular metals than the planetary system as a whole. The reason for this is not fully understood, but it may be due to the earth being formed by the accumulation and capture of a greater proportion of iron (and therefore siderophile-rich) than stoney (and therefore siderophile-poor) planetesimals than the planetary system itself.The third line in Table 1 is the average composition of the crust of the earth. With the exception of iron, all of the Group VIII transition elements are rare in the crust, present at concentrations of It tOO to Itt ,000 of that of the bulk earth. This is because the outstanding chemical characteristic of this group of elements is their siderophile nature; that is, their tendency to alloy with metallic iron. Because of this, once the earth became molten very early in its life history, these elements dissolved in the molten iron present at this stage and were removed from the outer accessible parts as this dense liquid sank to the centre of the earth to form the core. Although iron was the main instrument of concentration of the Group VIII metals, its much greater over-all abundance and its ability to combine with oxygen more easily than the others in the group means that significant amounts still remain in the oxidized portions of the earth.The fact that most of the Group VIII metals are available to use in workable concentrations at all is that they are 5 to 30 times more concentrated in the earth's mantle than the crust, as shown in line 4 of Table I. There has been a constant, if slow, interchange of matter between the mantle and the overlying crust throughout most of the earth's history and, under certain circumstances, this interchange has given rise to economic concentrations of metals."

Jan 1, 1979

By J. Armstrong, J. Bourgeois, S. Warren

The application of statistical analysis software programs has proven useful for investigation of rockfall runout distance along a designed slope. Rockfall modeling programs are continually being upgraded with more sophisticated analysis tools, such as the use of the rigid body versus lump mass models. Engineers at mine sites utilizing the software may have varied experience related to these models, their associated input parameters, and how to interpret the generated results. To address this concern, researchers at the Spokane Mining Research Division (SMRD) of the U.S. National Institute for Occupational Safety and Health (NIOSH) investigated the influence of slope height, slope angle, slope material, and rock size for both rigid body and lump mass models in a 2-D statistical analysis program. Based on a literature search and industry input, specific ranges common to that of an open pit mining environment were chosen for each of the input parameters to determine 90% rock runout distance as well as their sensitivity to change. Data collected from this numerical analysis and simulation will be compared to empirical rockfall data gathered through the duration of the Highwall Safety project conducted by NIOSH from 2022–2026.

Mar 2, 2022

By F. W. Brackebusch

A unique machine has been designed for mining narrow veins. The machine, called the NONN, walks on the walls of the stope and carries a boom-mounted hydraulic impact breaker. The concept of walking on the walls allows an existing muck handling system such as LHDs to operate beneath the NOMN. The NOMM has four sets of legs which can be manipulated independently or concurrently to cause the carrier to walk in any direction and to turn sharp corners. The mining rate using the breasting method is targeted to be 25 t/hr.

Jan 1, 1990

By T. P. Chidakwa, T. R. Stacey

This study investigated the corrosion rates of various steel types and coatings used for friction rock stabilisers in a deep-level gold mine under diverse underground environmental conditions. Testing was conducted in situ within ramps, intake airways, and exhaust airways, and through simulated laboratory experiments. Results revealed that environmental variations significantly influence the corrosion performance of different materials and coatings. Duplex coatings, made up of galvanised steel with an organic paint layer, demonstrated the highest corrosion resistance. Zinc-based coatings provided moderate protection, while 3CR12 stainless steel and uncoated S420 carbon steel exhibited comparatively poor resistance under both aqueous and atmospheric conditions.

Mar 4, 2025

By AIME AIME

LOCAL COMMITTEES. EXECUTIVE.-W. A. Lathrop, Chairman; R. V. Norris, Secretary; S. D. Warriner, Treasurer; Irving A.. Stearns, W. J. Richards, H. S. Drinker, C. D. Simpson. GENERAL RECEPTION.-Irving A. Stearns, Chairman. Archibald, James, Jr., Pottsville. Lawall, E. H., Wilkes-Barre. Ashley, H. H., Wilkes-Barre. Lentz, W. 0., Mauch Chunk. Ayres, WV. S., Hazleton. Lewis, Albert, Bear Creek. Beard, J. T., Scranton. Loomis, W. H., Jeddo. Bridgman, J. C., Wilkes-Barre. Markle, Alvan, Hazleton. Bunting, Douglas, Wilkes-Barre. Markle, John, Jeddo. Chase, F. M., Wilkes-Barre. Neale, J. B., Minersville. Coroner, Eli T., Scranton. Norris, R. V., Wilkes-Barre. Cote, E. B., Jr., Drifton. Oliver, Paul A., Oliver's Mills. Davies, W. H., Hazleton. Owens, W. D., Pittston. Davis, H. G., Dorranceton. Pardee, 1. P., Hazleton. Dodge, W. F., Wilkes-Barre. Quin, R. A., Wilkes-Barre.

Jul 1, 1911

By L. P. Meade

Dimension stone and salt are two of the oldest industrial minerals utilized. Salt has been and still is a necessity to the well being of man. Dimension stone on the other hand has been utilized by man to glorify conquests - both in the battlefield and corporate arena. Both commodities are important, but dimension stone has an additional use in that the survival lessons learned by the domestic industry can be applied to other contemporary industrial minerals, Specialization in the market place and customer service have allowed domestic producers to survive: subsidized foreign competition, obsolete equipment, and lack of capital.

Jan 1, 1986

By Jens Kempken

A competitive landscape pressurizes the steel producers business, zero defect requirements from customers forces the operators for additional efforts in process control and quality management. The so called quality related cost, which include also rework, cost for downgrading or even scabbing of material is already a remarkable lever in a plants profitability breakdown. The introduction of advanced state of the art grades in the product portfolio requires already a budgeting for the expenses for R&D and quality management. PQA has been developed as a process and quality management software solution next to existing level 2 or level 3 automation systems. It is focusing on the analysis of process data, equipment information, in line quality measurement devices and trend analysis to obtain an answer whether the process is according to definition and expectation and whether the intermediate or final product can be shipped for further processing as prime material. Advanced analytics which are linked to an expert know how based configuration identifies deficiencies in the production and processing process. An intelligent, state of the art quality rating system evaluates tolerable deviations. PQA comprises the software platform including the database, data configurator and collector from the different sources in the production process and units. The core element of the platform is the knowledge based expert know how package defining process and quality determining fundamentals. The paper describes the structure of the software package, it gives insights on the expert know how package, process and quality evaluation and points out the customer benefits, cost reduction, improvement yield, customer satisfaction increase. The link to recent operational references is given.

Oct 30, 2017

By J. R. Goode

The first part of this paper comprises a general discussion on refractory gold ores and their mineralogy processing methods now in use are reviewed and test procedures for the important methods are discussed. Factors determining the selection of a process are outlined. The paper includes a survey of production plants using pressure oxidation, roasting and biological oxidation to process refractory ore. The status of processes under development is briefly reviewed.

Jan 1, 1993

By E Jak, M Shevchenko, D Shishin

One of the key aspects to develop sustainable metallurgical production is to ensure that the predictive power of thermodynamic tools is brought up to a new level of accuracy and reliability. Exploring new polymetallic processes, integrating primary and recycled materials, means utilising the uncharted areas within the Cu-Pb-Zn-Fe-Ca-Al-Mg-Si-O (major) – Cr-Na (slagging) – As-Sn-Sb- Bi-Ag-Au-Ni-Co (minor) slag-solids-metal-matte-speiss-sulfate system. This requires extensive integrated experimental and thermodynamic modelling study, which is underway at PyroSearch at the University of Queensland (UQ).

Aug 21, 2024

By Phillip I. Merritt

"IntroductionDuring and since• the war, it has been my privilege to work closely with those in Canada who are responsible for the vital raw materials needed in our co-operative atomic energy programme. The understanding which has developed between our two groups in this all-important enterprise has been a great source of pleasure. We in the United States are aware of the importance of the contribution made by Canada to this project, and we look forward to continuing our mutually advantageous relationship.The impact of World War II, and the decision by Canada, Great Britain, and the United States to join in a programme for the development of atomic weapons, created a sudden and immense demand for uranium minerals. Early in the raw materials programme, it was evident that sufficient raw materials to fulfill war-time atomic weapon requirements could be secured from three sources: the rich pitchblende deposits of the Eldorado , mine at Great Bear lake; the Shinkolobwe mine in the Belgian Congo; and as a by-product of the vanadium industry of the Colorado Plateau in the United States. In the early part of the programme, therefore, our joint efforts were directed toward obtaining immediate maximum production from these localities. The contribution made by Eldorado Mining and Refining (1944), Limited, both in supplying and refining raw materials, was and continues to be of vital importance.In addition, it was also obvious from the first that in this programme, as in any mining enterprise, exploration activities directed•toward the discovery and development of new sources of uranium ore were essential if production were to be maintained over an extended period of time. In order to satisfy obvious security requirements during the war, it was necessary to proceed with this exploration programme, both in Canada and the United States, as secretly as possible. With the end of the war, and the revelation that an atomic weapon had been developed, however, secrecy in exploration was no longer required. The important thing was to get on with a broadened exploration programme."

Jan 1, 1950

By Jorge Cárdenas, Piero Mejía, Diego Gamarra

The present case study details the solution to a complex situation in a mining operation, involving the challenge of expanding the tailings storage facility in high-criticality areas adjacent to electrical rooms that provide continuous power to the entire mining process, including water pumping and drainage systems. For this purpose, blasting is required to prepare the construction areas for the new expansion facilities. Upon deciding to proceed with blasting, a comprehensive engineering assessment was conducted to ensure operational continuity without impacting the process, while generating sufficient fracturing in the rock mass to allow extraction with auxiliary equipment. Support from specialists through the Technical Assistance area was requested, and a detailed evaluation was carried out through advanced studies. Field vibration studies were conducted to define attenuation models and characterize the rock mass in the sector. With this information, simulations were carried out using predictive and probabilistic models with Monte Carlo methods to select delay charges and optimal timing for reducing vibration levels and increasing frequency levels. With these measures, the three blasts conducted near the Gas Insulated Substation room, which had distances ranging from 30 to 100 meters, produced the following results: • Vibrations; The three blasts conducted at distances of 100, 30, and 50 meters recorded vibration values of 5.3, 40.2, and 9.5 mm/s, all of which were below the maximum vibration level of 50 mm/s set by the projects area. According to the USBM RI8507-OSMRE standard, all values for Peak Particle Velocity (PPV) and frequency were below the permissible limits. • Flyrock; Through filming and post-blast inspection, it was confirmed that the ejections were within the safety zone. • Fragmentation; The results obtained showed a maximum overbreak size of 1.5 meters, allowing the broken material to be moved effectively.

Jan 21, 2025

By Stanley A. Feitler

This Bureau of Mines report deals principally with the resources and economic aspects of feldspar in the United States east of the Mississippi River. Although in a strict sense, all phases of the feldspar industry affect its economic structure, emphasis in this study is on supply, demand, and marketing. Although feldspar was originally mined for use in the manufacture of pottery and other ceramics, the glass industry, which began to use feldspar in the mid-1920's, now consumes more than half of the annual output. Most mining is open cut, and the methods used are similar to those used in mining crushed stone. Excess plant capacity has been chronic, and production is usually about 50 percent of capacity fur the industry as a whole. Since 1947, feldspar consumption has grown more slowly than the average for all U.S. industry. This has fostered intense competition, especially for the glass market. Prices have not kept pace with inflation, and profits are small. The trend of consumption through 1.970 for glass feldspar is expected to be upward; less rapid growth in consumption of ceramic feldspar is anticipated.

Jan 1, 1967

By Karl J. C. Harries

"14.1. INTRODUCTION1The boilerplate of an agreement is not a single provision, but a series of provisions that are expected in “every agreement”. They are sometimes also referred to as the “lawyer’s provisions”. Many businessmen consider the boilerplate to be superfluous and, to some extent, window-dressing by the lawyers – even legalese. They will often offer advice to the effect that it can “pretty well be ignored”. Such advice could not be more wrong.Most boilerplate provisions are essential parts of every agreement. Some may be part of a “standard package” and may have little relevance to the agreement at hand, but these are the exception rather than the rule. The exceptions should not be treated as justification for giving all these provisions short shrift. The boilerplate should receive the same review, consideration, and negotiation as the provisions that set forth the business deal. It is often these provisions that make the deal work or that are turned to at the time of disputes. If they are inadequate, as they sometimes are (unfortunately, some draftsmen are also loath to review or update their standard boilerplate provisions or to tailor them to the deal at hand), they can create problems, rather than offer solutions. Such problems can be costly and time-consuming for the parties to address. Inadequate or incomplete provisions may ultimately be one of the reasons for the parties to turn to the courts to settle their differences. On the other hand, good boilerplate provisions can help keep them out of the courts.One of the principal objectives of an agreement should be to provide procedures, or mechanics, for implementing agreed principles and for the parties to follow to settle their differences, real or perceived, without going to the expense and disruption of a lawsuit. An agreement should aim to keep the parties away from the courts, not serve as a springboard to the courts. It must nevertheless be acknowledged that, if there is a major falling-out among the parties to an agreement, the chances are that, however carefully the provisions of that agreement have been negotiated and drafted, the parties will end up before the courts or some other adjudicating body."

Jan 1, 2003

By M S. Cassola

It’s expected that the world economy will face a stable and continuous growth in the demand of iron ore, reaching more than two billion tonnes per year within the next year. After decades exploiting resources with high content of iron ore, now the industry faces the challenge to exploit and beneficiate more complex ores.According to the industrial practice, the flotation technology is one of the most important and effective beneficiation processes to deal with low-grade iron ores around the world. However, even with this, it is still necessary to search for new processing routes or promote the optimisation of the existing circuits.The broad application of this technology is an outcome that deeply relies on the proper selection of flotation chemicals specifi cally designed for each system. New collectors are in continuous development as flotation performance significantly relies upon their optimisation.The reverse iron ore flotation in Brazil, mainly constituted by haematite and quartz, uses ether amines as collector for silica minerals and caustic corn starch as depressor for haematite. The process selectivity is highly impacted by the features of the etheramine, such as:• mono or di-etheramine,• neutralisation degree,• chain length,• branched or linear chain,• the flotation pH, and• the size distribution of the flotation feed.This paper describes the experience obtained from laboratory and industrial trials on different ores, conducted to improve the selectivity and recovery in the reverse iron ore flotation by selecting the required collector for low-grade ores.

Jul 11, 2011

By Francis J. Quinn

The Natural Gas Act, of 1938, which put interstate pipelines under the jurisdiction of the Federal Power Commission, did not place a protective competitive shield around such companies - nor does any provision of the act guarantee them a profit. Natural-gas pipelines are competitive with each other and also with the coal and oil industries. Gas distributing companies must compete not only with the coal and oil industries, but also with the electric industry. Natural gas has captured markets from oil, which had taken them from coal. Oil men contend that gas prices have: been, held to an artifically low level by regulation. The electric industry is moving into the space-heating market, which pleases the coal people because the coal industry's largest customer since losing the railroads to dieselization has been the electric companies. The coal industry is attempting to monopolize the industrial and electric generating market through government intervention, and this is being done under the guise of concern for the national welfare through advocation of a "National Fuels Policy purporting to, further the cause of fuel conservation. Such a policy is contrary to American principles and would result in the individual's loss of freedom of choice and ultimately, in less reserves of preferred fuels because of diminished exploration efforts.

Jan 1, 1961

By Brij M. Moudgil

Flotation was introduced in phosphate rock processing in the late twenties and since then it has been an important part of the concentration process. More than two thirds of the rock produced in Florida is upgraded by the flotation process. Since no crushing or milling steps are involved in the material preparation, the flotation plant feed is coarser than in most other mineral flotation systems. During hydraulic processing of the rock, particles in the size range of -14, +150 mesh constitute the flotation feed. This size fraction is further classified by hydraulic sizers, stationary screens and vibrating screens into a coarse (-14, +35 mesh) and a fine (-35, +150 mesh) flotation feed. The flotation techniques for concentrating the fine feed as practiced by the Florida Phosphate producers have been standardized over the years, however, methods for upgrading the coarse feed differ from plant to plant. In this paper an effort has been made to present relative merits of the techniques employed for concentrating the coarse phosphate rock..

Jan 1, 1977

By S Leichliter

La Colosa, Colombia is a large gold-porphyry deposit currently undergoing feasibility studies by AngloGold Ashanti. This period of development allows the opportunity to apply innovative and emerging testing and modelling methods to provide a predictive geometallurgical recovery model for the deposit. By partnering with the AMIRA P843A Geometallurgical Mapping and Mine Modelling (GeMIII) research project, the geological and mineralogical data are analysed with respect to liberation and recovery methods. This will allow the variability in the geology and mineralogy of the deposit and key relationships recognised in the data to be included in the development of a model to help predict recoveries of the gold. Many aspects of the gold mineralisation such as gold paragenesis, associations, grain size and texture are determined and analysed using optical microscopy, Mineral Liberation Analysis (MLA), and laser ablation (LA-ICP-MS). At La Colosa the gold has been located in sulfides (eg pyrite, pyrrhotite, and chalcopyrite), silicates, along silicate phase boundaries, and among the pyrite-rich intermediate argillic alteration. Further testing and analysis will also determine if ‘invisible’ gold is present in the pyrite, pyrrhotite, and chalcopyrite. Recovery methods can also be determined and tested after combining the results of mineralogy tests with other data (eg results of comminution tests). Indices for the mineralisation and recovery are developed using image analysis and analytical testing. These indices are correlated with recovery data from the company to develop a predictive block model for recovery. The goal is to develop cost-effective, efficient methods to analyse the mineralogy and geology of the deposit; understand the variability in the mineralogy, geology, and recovery; and construct a predictive geometallurgical recovery model.

Sep 5, 2011

By Jochen Maurer, Dr. Christian Hoyme, Dr. Hans Regler

Currently, it is very difficult to obtain qualitative and quantitative information about the status and production process of a construction site. As a rule, companies depend on reports from on-site experts. There is no end-to-end digitalization due to the mobility of equipment and ever-changing locations. Equipment from different manufacturers, especially in special foundation engineering, is highly specialized. Any data collected by this equipment is recorded in proprietary formats and made available on the manufacturers' platforms. This exacerbates the situation, making simple analysis of performance indicators impossible. Most functions such as construction diaries, equipment utilization analyses, etc. are implemented only as standalone solutions. This does not allow for prompt visualization and intervention in critical process sequences because the construction site process is usually managed using a cost-based method. Furthermore, special foundation engineering requires a high level of expertise in an extremely wide range of construction processes. In this article, the results from a set of non-proprietary performance analysis tools are presented using numerous practical examples. Once a construction element is completed, the equipment data is immediately transferred to the platform using the latest cloud technology. Because the data is normalized, construction progress can be documented immediately, even for mixed equipment fleets. Bottlenecks can be immediately detected by visualizing the current performance of the production process, which is broken down into individual steps. Modern analyses of this equipment data improve quality, thereby providing better information about current performance. These sets of tools are essential for changing from the current monetary or cost-based method of process management to time- and bottleneck-oriented management. This makes it much easier to identify the critical path during projects. The article shows that processes can be documented and managed.