Search Documents

By N. Jovanovic, A. Vazirizadeh

"The main objective of this study is to find a solution to design a mass flow observer system with the minimum required sensors and maximum observability for a mineral processing plant. The second objective is designing a mass flow observer configuration with high reliability to manage sensor failures. This configuration will provide a robust monitoring system that increases plant availability and process measurement fault detection. Furthermore, the monitoring system is expected to improve process efficiency. In this investigation, the procedure of designing an observer system is presented along with three models to design the sensor network. The advantages and disadvantages of each models are discussed and finally the models result for an industrial case are presented and analyzed. INTRODUCTION The concepts of observability and redundancy of mass flow are directly linked with the ability to solve and estimate the mass flow. There are hundreds of streams in a process plant flowsheet, and for technical and economic reasons it is not possible to measure all mass flows. It is thus important to know for a set of measured streams, which of the unmeasured streams can be estimated. The concept of observability deals with this issue. It is also valuable to know whether a measured mass flow of streams can be estimated even if a sensor fails for some reason. Redundancy deals with this failure question. A stream is said to be observable if it can be estimated by using the measurements and/ or mass conservation equations. Also, a stream is redundant if it is observable even when its measurement is removed. Observability and redundancy analysis can be exploited for adding new measuring instruments. It can also play a useful role in efficient decomposition and data reconciliation problem (Narasimhan and Jordache 1999). The value of an observer system cannot be justified without considering its benefits. This justification is done through evaluation of data reconciliation, gross error detection and improving process performance such as outlined below:"

Jan 1, 2018

By Tyler Rockley, Cara Rosen

Blasting at a granite quarry in eastern Maryland produces elevated air blast readings that can fall into the cautionary zone for the state of Maryland environmental regulations on a semi-regular basis. When designing blast patterns in this quarry, challenging geology creates rough and uneven blast faces that can be difficult to capture with 2D laser profiling fully. Utilizing several methods known to manage high air blast results like pattern adjustments, decking, and timing changes have not achieved consistent outcomes.

Feb 1, 2020

By Oliver Schulz

This paper presents the latest references of the Siemens VAI slab casting technology. Following the connect & cast philosophy Siemens VAI has developed technological packages suitable for installation in existing casters of any original supplier, as well as for complete new machines. A major demand on new machines is to adapt quickly to different market demands. This requirement for flexibility can be divided into two actual trends. Firstly into casting a broad range of steel grades, thicknesses and width on the same machine and secondly having installed slab, bloom and billet caster in one steel plant to deliver all different types of needs on the market. Depending on the condition of the existing machine the focus of modernization ranges from the substitution of single components featuring state-ofthe-art technology to complete caster revamping projects. In this paper concepts and references for short machine outages and fast caster ramp-ups at moderate investment costs are presented.

Jul 30, 2018

By Orica

Unlicking the Possibilities ISEE Digital Detonator Workshop New Orleans, LA Wednesday, February 4, 2004

Jan 1, 2004

This publication summarizes the in-house and contract research projects programmed for fiscal year 1984 by the Bureau of Mines under its Conservation and Development activity. The document provides a mechanism for interested parties to gain insight into projects of the Bureau's Conservation and Development research program. The objective of the Conservation and Development Program is to provide the technological advances needed to stimulate the mining of domestic deposits containing critical, strategic, and other essential minerals in compliance with existing regulations and at costs sufficiently low to be competitive in world markets. Research efforts are directed toward improving the fundamental understanding of processes and procedures involved in the production of minerals. The overall goals will be accomplished by investigating alternative mining methods to increase domestic production of critical and strategic minerals from low-grade deposits; expanding the technology for the economic and efficient extraction of minerals consistent with cost-effective compliance with environmental regulations; and advancing the technologies needed to insure an adequate supply of coal.

Jan 1, 1984

By Frank W. Dickson, George Tunell

Five hot spring areas of the western United States show evidences of present day deposition of HgS; two also show evidences of accompanying Sb2S3 deposition. Sulfide minerals are depositing at or near the surface from hot waters that differ for each spring ai:ea in amount and kinds of dissolved matter. All the springs contain dissolved substances that act as buffering agents and that cause increased alkalinity with increasing temperature. Transport of Sb2S3 is possible in H2O and in boron and sulfide solutions. Increasing alkalinity and temperature enhance stibnite solubility. Quantitatively important transport of HgS appears restricted to alkaline sulfide solutions that contain HgS2=. Elemental mercury probably forms in deep hot waters because HgS breaks down into mercury and sulfur above 200°C, and free S is removed by reaction with water. Elemental mercury should accompany HgS2= in solutions that were at 200°C or higher. Cinnabar deposits from saturated alkaline sulfide solutions because of combinations of temperature decrease, dilution, oxidation, and reactions with wall rock: Amedee Hot Springs, Boiling Springs, and Coso Hot Springs are areas in which HgS is the only sulfide deposited. Hot waters at Amedee and Boiling Springs are supersaturated with HgS or transport colloidal HgS. Steamboat Springs waters deposit mainly silica and stibnite, but they have deposited HgS recently. Sulphur Bank waters deposit mostly stibnite and some HgS. The hot-spring waters of all springs represent highly modified deep water. Field and laboratory studies support the concept of transport of HgS in moderately alkaline sulfide solutions as HgS2=. Fluctuating deposition of stibnite and cinnabar reflects availability of sulfide or variations in deep-source HgS and Sb,S,. Silica and HgS dissolve mutually in alkaline sulfide solutions, and cinnabar and quartz would be expected to deposit simultaneously. Free mercury given off by hot-spring waters would impregnate country rocks.

Jan 1, 1968

By Richard E. Thill

Engineering properties of rock are essential in most phases of mining from site reconnaissance through mineral processing. Review of the literature indicates, however, that property data is scarce for most coal measure rocks in the United States. The Bureau of Mines, U.S. Department of the Interior, has undertaken a wide-ranging testing program to provide more complete property data for coal strata in the U.S. coal basins. The property data are expected to have application in geophysical exploration, the development of pre- mining and hazard detection probes and instrumentation, mine design, engineering and rock mass classification, subsidence engineering, and ground control. This paper describes the comprehensive program encompassing in situ geological, geophysical, and geotechnical properties and laboratory determinations of acoustic, electromagnetic, physical, mechanical, and index properties and discusses results for 500 ft of coal measures at a minesite in the Northern Appalachian, Eastern Coal Province.

Jan 1, 1982

By H. E. Heide

"Before the war, the United States was the world’s leading consumer of tin, the industrial applications of which had become widespread. Domestic production was negligible, and requirements were met almost entirely by imports, principally from British Malaya, United Kingdom and China. Average annual imports for the years 1925-1929 amounted to 78,009 long tons.With the advent of war in Europe and signing of the Japanese-German pact, it was realized that foreign sources of supplies were threatened, and steps were taken by Congress to forestall critical shortages of tin and other minerals. These steps in regard to tin included stock-piling, improving reclamation and conservation, increasing South American production, constructing a smelter in the United States for treatment of tin, ores, and intensifying the search for domestic tin deposits. Annual imports were raised to 140,873 long tons by 1941. On 1945, annual imports had shrunk to 37,675 long tons and consumption had been reduced to 52,100 tons of primary and secondary tin but not tin content of scrap alloy.The Strategic Minerals Act, passed by the Congress in 1939, authorized the investigation of domestic tin deposits.As Alaska had supplied virtually all of the domestic output of tin, an investigation of Alaska deposits was undertaken in 1940 and 1941 by J. B. Mertie, Jr., and Robert R. Coats of the Geological Survey.The Lost River lode tin mine on the Seward Peninsula was examined by H. E. Heide of the Bureau of Mines in 1942. Possibilities for developing a significant amount of tin appeared favorable, and exploration of the ore bodies was started in August 1942."

Jul 1, 1946

By Gus Van Weert, Samuel A. Bolorunduro, David B. Dreisingerm

"As deposits of high-grade base metal sulphides become depleted, attention must be focused on the treatment of complex sulphides, which contain significant fractions of precious metals such as gold and silver. Acid pressure oxidation is a promising process for these materials and the recovery of silver and gold will improve the economy of the process. Gold can be recovered from the oxidised residues, however, silver is incorporated into the jarosite specie and the cyanidation of the resulting residue yields very low recovery.Pressure oxidation of various complex sulphides was carried out at 110-150°C in sulphate media with additions of potassium iodide under conditions similar to industrial autoclaving. The resulting residues were subjected to cyanidation. High recovery of silver, up to 98%, was achieved because its incorporation into lead-hydronium jarosite during the pressure oxidation was minimised, while its deportment into the cyanide-soluble silver iodide was favoured. Silver recovery decreased slightly at high temperatures (140° and 150°C) because of the enhanced stability and kinetics of lead-hydronium jarosite, but this could be overcome by increasing acidity and iodide concentration of the autoclave slurry."

Jan 1, 2003

By R. H. Nafziger

Owing to the growth of alloy steel production and its influence on tramp element levels when recycled, foundries have expressed concern regarding the quality of scrap used to prepare iron castings. Reliable and current information was unavailable on the amount of tramp elements contained in iron castings over time. Accordingly, the U.S. Bureau of Mines, in cooperation with the American Foundrymen's Society (AFS), analyzed cast iron samples from participating foundries throughout the United States on a quarterly basis to ascertain possible trends. Each sample was analyzed for 28 elements to determine if changes had occurred as a function of several input variables. This bulletin describes the research and presents analytical results and evaluations over a 5-3/4-year period from January 1981 to September 1986. Results show that iron casting compositions are changing with respect to a few tramp elements such as arsenic, cobalt, chromium, tin, and zinc over the period. Changes in charge compositions probably are responsible. Significant variations between zones also were observed with aluminum, arsenic, cobalt, chromium, copper, and manganese.

Jan 1, 1990

By Jean-Paul Drolet

"This paper charts, briefly, the :salient facts of international trade in minerals and their products and Canada's place in it. It also reviews inter-national agreements, economic groupings and national measures to channel and regulate production and trade in minerals. Canada's mineral industry now produces raw materials worth $3.7 billion per year, making this country a giant among mineral producers. Two-thirds of this production is exported, chiefly to the United States, accounting for about 30 per cent of Canada's merchandise exports and topping all other classes.However, several other nations are also pressing the development of their mineral resources and markets. The Soviet Bloc, China and principally Australia and Africa are becoming important suppliers of basic raw materials to some traditional markets of Canada in Europe and Japan.The outlook for Canadian mineral exports to the countries of the Common Market, Great Britain and Japan is good, although some tariff barriers remain troublesome.Concerning the United States, our most important market, Canada is seeking to have that country lift import quotas on lead and zinc, and re-cent statements by U.S. authorities give hope that this may be achieved soon. Moreover, Canada wishes to obtain easier access to the American market for several of its metals and minerals.Canada is now participating in the Kennedy Round of tariff talks under the auspices of the General Agreement on Tariffs and Trade (GATT), and is seeking to open wider doors for its exports of products.In summary, Canada has done reasonably well in some mineral commodities on world markets, but has lost ground in others. Any slackening of Canada's efforts in the development and marketing of mineral resources would soon lead to the decline of its role in the world miueral economy."

Jan 1, 1966

By D. W. Zandee

"IntroductionHaving mined an economic mineral bearing rock which is of insufficient grade to warrant direct smelting, upgrading or beneficiation is required to make it an economically viable ore. The first step in effecting the concentration process is comminution or sequential breaking of the rock to allow liberation and subsequent recovery of the desired mineral particles. Desirably the ore could be broken down to the point where the valuable mineral is completely liberated to maximize the chance of recovering as much of it and in as pure a form as possible. The number of energy intensive stages of breakage required to attain this goal depends on many physical characteristics of the ore such as hardness, friability, toughness, grain size, existing fracture planes and particle shapes.Commonly the distinct stages are primary, secondary and often tertiary crushing and finally grinding. To increase the efficiency of each stage of size reduction, pre-treatment sizing is common.Crusher feed is commonly scalped of large pieces or screened for reduction crushers and classified for secondary grindingcircuits.Although crushing and screening is employed for many different products, this chapter reviews current practice in larger tonnage metalliferous ore treatment plants.Current practice is to use large gyratory or jaw crushers for primary crushing and some sort of gyrating or cone crushers for additional stages of reduction. For autogenous or semiautogenous grinding circuits only the primary crushing stage is necessary, the balance of the work being performed in the grinding stage. For conventional grinding circuits using ball mills or combinations of rod and ball mills, secondary, tertiary and even quaternary crushing stages are normally required.Older type crushers such as stamp mills, double rolls, sledging mills and hammermills are no longer common but are used for small tonnage special processes.Important to efficient crushing are a variety of sizing devices such as grizzlies and vibrating screens. Products at different stages must be stored to give surge capacity and allow controlled feeding rates through mechanical and gravity feeders. These storage piles, bins and feeders as well as crushers and screens are commonly integrated into a total facility by means of conveyor systems. Most often these are endless rubber belts driven by simple or multiple drive mechanisms usually consisting of electric motors and speed reducers."

Jan 1, 1989

By G. Kolosay, J. Rajala, G. Deschênes, A. Romanov

ABSTRACT: The Kupol project, located in Far East Russia, treats a high-grade, free-milling ore containing 25.5 g/t Au, 298.3 g/t Ag, and 0.5% pyrite,with a P70of 53 microns. Most of the gold occurs as elec-trum and the silver is predominantly present in the forms of acanthite, stephanite, pyrargyrite, andproustite. The mill reached the design throughput of 3,000 tpd six months after start-up. AKnelson con-centratorrecovers10.4% gold and 0.5% silver. Leaching (14.5 hours pre-treatment and 116 hours cyanidation)of gravity tailings is performed with the CANMET Enhanced Leach Process (CELP),using only 490 ppm NaCN (cyanide consumption of 1.1 kg/t). The precious metals are recovered by counter-current decantation and the Merrill-Crowe process. Calcium hypochlorite destroyscyanide and thiocyanate. Overall, gold and silver recoveries for 2008 were 95.4% and 85.6%,respectively (2.8% and7.5% higher than targets). In the first eight months of 2009, gold and silver recoveries were 95.0% and82.6%, respectively. By August 2009, the mill processed 1.42 million tons of ore with production of 1.1 million ounces of gold and 11.3 million ounces of silver. CELP performance was not affected by changes in feed grade and ore mineralogy. Additional modifications to the leaching strategy allowed further reduction in cyanide consumption and effluent treatment costs.

Jan 1, 2011

By H Kurth

High specification Prompt Gamma Neutron Activation Analysis (PGNAA) has been successfully applied to conveyed flows at iron ore operations since 2002 to representatively measure ore quality for improved quality management and process control. While the PGNAA technique has changed little since that time, significant improvements have been made in measurement capability. Elements previously unable to be measured well or at all using this technique are now measurable and one of these is phosphorus. Aluminium and magnesium are also key elements in addition to calcium and silicon in determining sinter basicity in ironmaking. Other elements measured routinely in iron ores include iron, carbon, potassium, sulfur and manganese. The benefits of representative measurement cannot be overstated as iron ore mining operations in South Africa, Europe, Australia, Asia and the Americas have discovered. The technology is applicable to any conveyed flow where elemental analysis in real time assists with quality management, from raw materials in ironmaking through to scrap steel in steelmaking and coal quality for coke-making. Major benefits are realised when raw material processing is optimised and this often includes diversion of material meeting a required quality so it can bypass unnecessary processing. This includes waste rock which can be diverted from a plant feed stream in 30 sec increments or ore that meets product quality being diverted to bypass beneficiation. Analysers are successfully utilised to identify ore types that assist with upgrade optimisation in jig plants; measuring feed, product and discard flows to also account for metal content. Product flows to stockpiles help manage production flows and stockpile qualities for different products and assist in blending ores into trains or ships to confirm specification compliance. Technologies can be used in magnetite processing but are predominantly used in hematite and goethite ore processing operations. The paper details examples of the above applications at various operational sites providing estimates of economic benefit as well as operational improvements.

Sep 18, 2023

By F. W. Wood

A program of research was conducted by the Bureau of Mines to investigate anomalies in electrical-discharge behavior during consumable-electrode arc melting of titanium and to study the effects of these irregularities on arc-furnace explosions. A major effort was devoted to an experimental survey of arc behavior and a qualitative definition of discharge phenomena.3/ An important conclusion was that the "glow" of industrial arc-melting terminology is not a glow discharge but a skittering arc in a displaced position. The conditions that permit displaced skittering were tentatively defined. The displaced skittering arcs tended to damage melting crucibles in two ways, and details of possible mechanisms leading to crucible rupture and explosive reactions have been proposed accordingly. However, no acceptable means of preventing crucible damage was discovered.

Jan 1, 1961

By Chas. H. Behre

MINING geology, both theoretical and practical, continued to make noteworthy progress during 1938. Mining companies generally, stimulated especially by the improvement in economic conditions during the latter part of the year, extended their workings and developed new ore bodies. Federal and state surveys expanded their search for favorable localities and actual ore bodies, with corresponding enlargement of regional knowledge. Theoretical investigations covered geochemistry of ore deposition, structural control of mineralization, and mineralogy of the ores (chiefly aided by the microscope). More geochemical work is greatly needed: ore searching is still too purely empirical, based on features that have been recognized else- where. Thus, clearer understanding of the conditions essential to transportation of metal salts is needed. Jean Verhogen has suggested that solubilities

Jan 1, 1939

By P. Favreau

This paper describes the progress accomplished at the Noranda Technology Centre in the field of three-dimensional computer-aided underground blast design. Traditional methods of laying out underground blasts are reviewed, and the new computer-aided approach is described. Time savings achieved through the use of BLASTCAD can be advantageously used to better engineer blasts, using models and blast vibration analysis. Future work involving the attachment of blast models directly to the system is also addressed.

Feb 1, 1993

By Charles G. Maier

"INTRODUCTION The use of thermodynamic calculations to answer practical problems in metallurgy, especially those that are relatively difficult to test experimentally, is rapidly becoming a conventional method of procedure. Nevertheless, these methods cannot he applied effectively until the fundamental thermodynamic constants used for them have become available either by direct experiment or by recalculation of data already existing in more or less undigested form.In an attempt to collect such data far the compounds of lead and the antimony group the incentive has been to make a preliminary survey that will disclose the gaps or questionable phases of available information and to collect data that may be used to answer certain rather practical problems presented by operating metallurgists.This report comprises three sections; the first gives the basis of selection of the constants which may now be given or estimated, and the later sections discuss the application of the figures obtained to two of the more interesting problems.The reader will discover that many of the quantities involve critical study of a number of more or less discordant observations. Although certain data could be rejected on the basis of thermodynamic comparisons, it must not be overlooked that many of the figures are the results of rational estimates rather than exact experiment. The use of thermodynamic methods to control and partly authenticate such estimates is one of its most valuable characteristics for the practising metallurgist or chemist, who cannot check by direct experiment each property of the materials which he converts to usable form.Nevertheless, while it is definitely possible in certain instances that the final figure selected for the heat or free energy of a process or substance may be in error by as much as a few hundred to a few thousand calories per formula weight, questionable figures are usually revealed by the thermodynamic calculations made. When quantities of such degree of accuracy are, and they often must be, used for estimating an unknown reaction, the result often gives no more than the order of magnitude of the desired quantities. Yet even in these extreme cases the answer is far more reliable and valuable than an unordered guess or a conclusion based on incorrect data."

Dec 1, 1934

By C. G., Fink

The dissolution of gold by cyanide solutions was studied by determining the time required for the solvents to dissolve gold leaf. Minute traces, even 0.5 ppm, of sulphide ion retard the dissolution of gold, and this behavior cannot be accounted for by the presently accepted hypotheses involving oxygen-depletion or thiocyanate formation. On the other hand, traces of the salts of lead, bismuth, mercury, and thallium considerably accelerate the dissolution. The beneficial effect of lead is dependent upon the pH and cyanide ion concentration of the solution.

Jan 1, 1950

By J. Wade Watkins, Joseph W. Horne, Arthur Matzick

"A successful procedure for the recovery of a valuable product from weathered tank-bottom settlings has been developed in the laboratories of the Bureau of lines and used in a field pilot plant. These heavy emulsion settlings, generally regarded by the industry as waste material, have usually been drained into open pits or storage ponds and eventually destroyed.Laboratory examination of the waste material shows it to consist essentially of a ""water-in-oil"" emulsion containing a considerable volume of congealed ""paraffin."" This paraffin is mainly high-melting-point wax; known in the industry as microcrystalline wax, for which there is an increasing demand.Because of the physical properties of this wax, the tank-bottom settlings are not responsive to conventional methods used for demulsifying ordinary crude-oil emulsions.The work upon which this report is based was conducted by the Bureau of Mines in cooperation with -the Kansas State. Board of Health and with special cooperative agreements-with the Cities Service Oil Co, Bartlesville, Okla., and the Bareco Oil Co,. Barnsdall, Okla. The studies were made under the general supervision of R. A. Cattell, chief engineer, Petroleum and Natural-Gas Division, Bureau of Mines, Washington; D. C., and H. C. Fowler, supervising engineer, Petroleum Experiment Station, Bureau of Mines, Bartlesville, Okla., and under the direct supervision of Ludwig Schmidt, senior petroleum engineer, Bureau of Mines, Bartlesville, Okla.Gratefully acknowledged are the assistance and cooperation given by the Cities Service Oil Co. of Oklahoma and especially by M. J. Kirwan, manager of production, and by Q. E. Beecher, general superintendent of production, Bartlesville, Okla., and to members of their staff at Oil Hill, Kans.The assistance and suggestions of V. R. Oakley, general superintendent, E. R. Wiles, director of research, L. G. Willis, field engineer in charge crude-oil supply, and Gerald DeWalt, chief chemist, and his staff of the Bareco Oil Co., Barnsdall, Okla., were of much value in the laboratory and recovery work."

Mar 1, 1946