Search Documents

By D. Meadows, P. Carrato, E. Wingate, K. Churchill

Extracting lunar ice, to be processed into pure water or hydrolyzed into oxygen and hydrogen, faces many challenges. On the Moon icy-regolith deposits that contain up to 10% water are found within Permanently Shadowed Regions (PSR) at both lunar poles, where temperatures approach -220 ⁰C. NASA has identified several technology gaps that exist in developing these resources including: • Excavating large quantities of icy-regolith • Delivering large quantities of acquired resources • Hardware that is lightweight and energy efficient • Hardware that is reliable and durable. NASA uses public challenges to incentivize innovative approaches to closing these gaps. The Break the Ice Lunar Challenge provides over three million dollars in prize money to teams that compete in developing solution to mining the Moon. This paper describes the rules for this challenge and presents some of the proposed solution.

Feb 1, 2023

By Jaisen Kohmuench, Michael J. Mankosa

Flotation has long served as the foundation for sulfide mineral recovery. As ore grades decline, however, this traditional approach is being pushed to the limit. Nowhere is this more evident than in the challenge of recovering coarse, partially liberated particles — an area where conventional flotation systems typically underperform due to excessive turbulence. As a result, valuable coarse minerals are often lost to tailings. Fine grinding has become the default solution, although with the added burden of higher operating costs and more challenging tailings disposal. To address the challenge of coarse particle recovery, Eriez developed the HydroFloat, a technology that uses a novel fluidized-bed approach to extend the upper particle size range of flotation significantly. The HydroFloat can recover particles exceeding 0.5 mm in diameter with a sulfide surface expression as little as 2 percent. Coarse particle recovery allows for optimization of comminution circuits for coarse gangue rejection before fine grinding. A substantial increase in overall tailings particle size provides higher water recovery due to improved drainage and allows for consideration of a dry, stacked tailings option instead of a tailings dam/impoundment. The technology’s transformative potential has not gone unnoticed. In recognition of its impact, Eriez was honored with the 2024 Robert E. Murray Innovation Award, commonly referred to as the Murray Award, by the Society for Mining, Metallurgy & Exploration. This prestigious award was established in 2017 to recognize organizations that advance the mining industry through the implementation of technical innovation. The HydroFloat stands as a fitting example of how creative thinking and industry collaboration can solve long-standing technical challenges.

Oct 1, 2025

By Paul Gemmill

Production was first recorded from the Pioche district in 1864, and it has continued to show an inherent ability to take on new life after periods of depression in the metal markets. Production from replacement leadsilver- zinc sulfide ore bodies in limestones of Cambrian age now accounts for several times the gross value of silver production from rich fissures in Lower Cambrian Quartzite. Aggregate production of some 6 million tons represents a gross value over $100-million. Future output is expected mostly to be from limestone replacement deposits of which the most productive are "channels" of ore up to several hundred feet wide and several thousand feet long with thicknesses from a few feet up to 50 feet. Such channels are restricted to the lowermost limestone bed of the district, about 250 feet above the basement quartzite. The "blotter-like" characteristic of this highly productive Jimesto~e bed in absorbing mineralization is believed to be, at least in part, due to lithology, including free carbon in the bed, which has created a unique set of conditions for delicately balanced mineralizing solutions that rejected any tendency to replace siliceous wall rock and were properly constituted for replacement of Limestone. All recognizable orogenic history is considered to be related to the Basin and Range faulting that created the mountain ranges. The faults developed after mid-Tertiary time and after widespread extrusives that are themselves involved in the faulting. Flat faults, formerly believed to be part of regional thrust faulting, are now interpreted as gravity slide faulting that can be shown to be large in magnitude and not simply local landslides. Large slide faults generally have concealed the great magnitude of mountain-bordering faults. Mineralization that accounts for ore is later than the faulting. Most faults are pre-mineral since they influence the shape of ore bodies, and some clearly have been offset by fault fissures containing ore. Post-mineral movement probably has been an important component of some large, initially pre-mineral faults. A single period of mineralization was begun by the introduction of large quantities of ironmanganese carbonate, and, in places, carbonate manganese with minor values in sulfides. Closely following the carbonate invasion, massive sulfides were brought in, usually replacing part of the carbonate body though in some places the massive sulfides replaced limestone that was not previously mineralized. Manganese mineralization is not a "halo" but leaks of manganese to higher formations and to the surface are the most significant exploration guides. The Pioche district is expected to be long lived with technological developments in ore treatment being important to the exploitation of low-grade manganiferous ores, while aggressive exploration is expected to find important quantities of bedded lead-silver-zinc ores of the massive sulfide type.

Jan 1, 1968

By F. W. Gray

Summarized Foreword This paper is one of a series arranged by Institute Divisional Committees for the Fiftieth Anniversary Meeting, reviewing the experience of the major mining and metallurgical industries during the life of the Institute. The viewpoint is national and broadly technical. Geology is stressed on a continental scale without regard for provincial boundaries. The boundary between Canada and the United States is, however, so decisive a factor in our coal-mining economics and our political evolution that mention of its implications cannot be avoided. The Laurentian Shield in Canada makes the occurrence of coal deposits a geological impossibility between the St. Lawrence Lowlands and the Great Plains. All but five per cent of Canadian coal resources occur west of Winnipeg. The utilization of this ninety-five per cent of our coal wealth has to date been a consequence of transcontinental railways' development, and the small fuel needs of thinly populated wheat farming and cattle-raising territory, in what- to judge from the development of mixed farming and greater population density of Manitoba- is merely an initial stage of agricultural intensification and accordant population growth. There is no useful purpose in measuring coal resource against consumption rate in the West as a whole, because the resource is but partially known, and it is difficult to believe that industrialism based upon coal utilization is in any but its infant stage of growth. Canada west of Winnipeg possesses, moreover resources of petroleum and natural gas, which, together with the power-potential in the long watershed of the eastern slope of the Rocky mountains, give to population centres such as Calgary and Edmonton a choice of energy resources that is almost an embarrass des riches.

Jan 1, 1948

By Campbell Robertson

The evolution of electronic detonators in commercial mining, construction and demolition has been a transformative journey, characterized by technological innovation, enhanced safety measures and improved precision. This abstract explores the historical progression and key advancements in electronic detonator technology highlighting its impact on the industry as well as the challenges in deploying these types of technologies. Electronic detonators represent a significant departure from traditional initiation systems offering precise timing capabilities and improved reliability and safety. The early development of electronic detonators can be traced back to the late 20th century with the introduction of basic electronic initiation systems. These early iterations provided a glimpse into the potential for greater control and accuracy in blasting operations. As technology progressed, electronic detonators underwent significant refinement incorporating advanced features such as programmable delay times, multiple firing sequences, expanded blast size and enhanced communication capabilities. These advancements revolutionized the way explosives are deployed in mining and demolition applications enabling engineers to tailor blasts to specific geological or environmental conditions and structural requirements. One of the most notable developments in electronic detonator technology is the integration of microprocessor-based control systems. These systems allow for precise calibration of detonation parameters, including timing, sequence, and energy distribution. By leveraging microprocessor technology electronic detonators have become increasingly sophisticated offering unprecedented levels of precision and safety in blasting operations. The advent of wireless communication technologies has further augmented the capabilities of electronic detonators. Wireless detonation systems enable remote initiation and real-time monitoring of blasting operations enhancing safety by reducing the need for personnel in hazardous environments. The evolution of electronic detonators has also been driven by a growing emphasis on sustainability and environmental stewardship. Modern electronic detonation systems are designed, amongst other objectives, to minimize environmental impact, achieve optimal fragmentation outcomes and reduced misfire rates during blasting. These advancements not only improve safety for workers and surrounding communities but also contribute to a more sustainable approach to mining and/or demolition activities. In conclusion, the evolution of electronic detonators has transformed the landscape of commercial mining and demolition offering unprecedented levels of data integration, precision, safety, and environmental responsibility. As technology continues to advance, electronic detonators are poised to play an even greater role in shaping the future of blasting and explosives engineering.

Jan 21, 2025

By Paul M. C. B. M. Cools, Martin Th. van Staveren

In 2010, the 5-years joint industry programme Geo-Impuls started in the Netherlands. The ambitious goal of this programme is to reduce geotechnical failures in our civil engineering projects by half in 2015. In the Geo-Impuls programme over 40 client organizations, engineering firms, contractors, research institutes, and universities are involved. In a risk-driven way, and based on top risks and dilemmas, the participants defined three central development themes. These themes are (1) contracts, for dealing with legal issues, (2) geo-engineering, for dealing with technical issues, and (3) communication, for paying attention to differences in risk perception by the human factor. In total 12 Working Groups contribute to these themes by producing one or more specific tools. These provide practical solutions for how to deal with contractual, geotechnical, and communication issues. The tools include working processes, guidelines, best practices, as well as some instruments. The development of these tools, as well as the available results, will be presented in this paper. From the start, Geo-Impuls embraced geotechnical risk management (GeoRM) as the risk-driven way of working for geotechnical engineering and construction. Over the past years, GeoRM and its supporting tools were already successfully applied in several projects. Therefore, the paper also describes also the GeoRM implementation process, including the quality assurance and control. Finally, the effectiveness of GeoRM will be discussed, by summarizing an analysis of all published geotechnical failures and accidents in construction projects in the Netherlands, which decreased substantially over the past 4 years.

Jan 1, 2017

By Paloma Lazaro, Moe Momayez

Interactions between human beings and their work environment require the body to regulate its temperature by balancing heat production and loss. Comfortable environmental conditions are crucial for keeping workers safe and healthy and to maintain a suitable level of productivity. However, achieving a proper core body temperature may become challenging under different conditions, especially in high heat-generating workplaces such as hot underground mines. Because hot underground mines have the potential to expose workers to heat stress, compliance with standardized and regulated indices and criteria is distinctly required. The objective of this paper is to provide an overview of the current research on heat stress and strain in hot underground mines, collected from published and specialized literature. General definitions, statistics of heat-related accidents in mining, overview of the indices, standards, and recommendations for heat stress are provided herein.

Oct 6, 2020

"INTRODUCTION These inspection standards have been prepared for use as a guide for the Federal inspection of anthracite mines. They are a revision of ""Tentative Inspection Standards for Anthracite Mines,"" published as Bureau of Mines Information Circular 7231 in January 1943 and used as a guide for Federal inspections. Numerous changes in the original standards have been made, due in part to recognition of shortages of some types of safety equipment due to the war, in part to need of additional standards to cover certain mine conditions and practices, and in part to conditions not foreseen when the original standards were prepared.Throughout these standards reference is made to determining the methane content of the mine air by using a permissible flame safety lamp. The Bureau has approved various electrical devices for the detection of methane, but it is recognized that new devices for determining the percentage of combustible gases as well as the percentage of oxygen, might be perfected for general use in mines, and therefore it may be necessary to revise certain standards to include the use of such equipment if and when the device is accepted as being permissible.About one-fourth of these standards are marked with an asterisk (*) as being of particular importance in preventing accidents in many coal mines; however, failure to carry out the suggestions made in such of the other standards as are applicable may also lead to loss of life.With continuing change in mining methods, some of these standards may become inapplicable, and further revision will be advisable. Therefore, question regarding these standards and suggestions regarding new standards should be brought to the attention of the Bureau, so that changes may be made from time to time. Numerous changes proposed by mine operators and by State mining departments have been incorporated in these standards."

May 1, 1944

By Y Lanwin

The Australian mining sector is undergoing a significant transformation with the adoption of advanced technology to the operational landscape. This has highlighted a critical disconnect between our traditional educational systems and the skill requirements of working with these advanced technologies. This paper aims to provide a behavioural science analysis of how the traditional manufacturing mindset, deeply rooted in our educational frameworks from primary to tertiary education, registered training organisations (RTOs), and in-house learning and development, is misaligned with the needs of today’s technologically advanced mining operations. Originating in the industrial revolution, the manufacturing mindset prioritised efficiency, mass production, and the division of labour. In educational institutions, this translated into an emphasis on rote learning, linear examinations, and a rigid adherence to processes and procedures. Such a system, while effective in producing a workforce suited for repetitive and predictable tasks, falls short in fostering skills like problem-solving, adaptability, flexibility, and coping with change – skills that are increasingly vital in a mining sector dominated by automation, robotics, and AI. The paper discusses how the focus on disciplined adherence to standard work procedures and processes in educational and training programs has inadvertently stifled creativity and autonomy in learners. This issue is compounded in the workplace, where employees, having been conditioned to operate within strict guidelines, now face the challenge of adapting to environments where autonomous decision-making and creative problem solving are crucial. In essence, the traditional approach to education and training has prepared individuals for a world of work that no longer exists. This paper advocates for a whole of pipeline approach, grounded in behavioural science, to revamp mining education and training. It highlights the importance of understanding and influencing the behavioural aspects of learning and recommends for an approach that promotes diversity, critical thinking, and adaptability, preparing the workforce to excel in the rapidly changing landscape of the Australian mining sector.

Sep 1, 2024

By Charles W. Daugherty

INTRODUCTION The Washington Metropolitan Area Transit Authority's (WMATA's) rapid transit system, Metro, ultimately will comprise 162.5 km (101 miles) of line divided among 10 routes. As shown in Figure 1, about 24 km (15 miles) of the system will consist of mined rock tunnels distributed along the A, B, C and K Routes. The structural construction contracts for all of the A, C and K Route rock tunnels are complete and trains are running in about one-third of them. A contract for construction of rock tunnel section B-9, the southernmost third of the B Route, was awarded on June 27, 1980. The final design of Sections B-10 and B-lla, the remainder of the rock tunnel portions of the B Route and the Metro system, are well advanced and should be under con¬struction by 1982. Of Metro's 87 stations, 11 will have been constructed by mining in solid rock, a not inconsiderable achievement, since each structure must be over 183 m (600 feet) long, wide enough to accommodate two trains and one or two passenger platforms, and high enough to achieve a stable arching action without encumbering columns. With the passage of years, some original priorities have been reordered, and ways have been sought to streamline and simplify this most complex of Metro structures without grossly violating the architectural standards that make it unique. This paper will summarize that search, and describe the design and construction aspects of the resulting product, the dual chamber rock tunnel station.

Jan 1, 1981

By M. Michael, A. Felber

"Mining activities, especially underground mining operations, create great demands on utilized haulage means which cover a variety of different horizontal and vertical distances. In the course of the continuous optimization of the haulage process, the application of textile machine elements, in particular synthetic fiber ropes, offers new opportunities. Therefore the current level of knowledge needs to be improved based on extensive analyses. For the estimation of the scope of these analyses, different fields of application and occurring environmental influences which have an impact on synthetic fiber ropes during their use in underground mining have to be evaluated. The Chair Underground Mining Methods of the TU Bergakademie Freiberg works on a scientific project concerning the use of synthetic fiber ropes in underground mining operations. This paper focuses on the potential application of synthetic fiber ropes in haulage systems in underground mining and exposes critical influences as an outcome of the working environment. These first investigations are the basis for the development of an appropriate experimental series. SYNTHETIC FIBER ROPES FOR UNDERGROUND MINING OPERATIONS The main idea is to optimize underground haulage means to develop even more economic systems. The new and lightweight design of single machine elements seems to be the first step to accomplish this goal. An example is the lightweight design of shaft hoisting ropes. The commonly used steel wire ropes are very heavy and are endangered to snap due to their own weight when reaching a distinguishing length. Thus they may not or only conditionally be used for deep mining operations utilizing shaft haulage. Ropes made of high-tech synthetic fibers weigh only an eighth of steel wire ropes while displaying the same tensile strength. This relation is shown in Figure 1, based on the comparison of fiber strength and density. This could offer new opportunities for deep mining operations, which are anticipated by many mining companies. /1/"

Jan 1, 2015

By I. Caraconcea, M. Cousineau, S. Gariepy

"Several base metal plants operate in low grade/high tonnage conditions which impose strict cost control on all fronts for their operations to remain profitable. This leads to decisions regarding plant design, procurement, operations and maintenance that often favor cost minimization over value optimization. This may hinder the representativeness of the metal accounting systems while this should be a priority in a low margin environment. Such poor representativeness not only creates confusion in plant scheduling but can also hide suboptimal metallurgical performance. Furthermore, this situation can run undetected for a while since one dominant feature of a poor metal accounting system is its poor self-awareness. During their practice, authors have particularly identified measurement bias and reproducibility, as well as their impact on metal recoveries as areas of concern. These issues have not been extensively reviewed in the specific context of precious metals in base metal plants. Pragmatic solutions are proposed either at the design stage for a new project or to retrofit an actual operation. These solutions should be based on a business analysis that set a value of information matching the contribution of precious metals as well as the potential to use such information to act toward increasing plant profitability. Conclusions are that trade-offs are an inherent part of the design/audit/retrofit of any metal accounting system in any plant processing either base or precious metals. However, compromises must be evaluated on economic/technical ground.INTRODUCTION Every mineral processing plant must produce metal accounting reports (Morrison, 2008) where estimated saleable metal flows and inventories are published. These metal accounting reports are delivered to a variety of stakeholders who use them for internal management purposes (day-to-day plant production planning, plant operation optimization, capital spending, etc.) as well as for external management (royalty settlements, tolling agreements, etc.). Hence, there should be no doubt that state of the art metal accounting is instrumental for mining companies to reach and sustain high-quality corporate governance (Gaylard, Randolph, & Wortley, 2014). However, producing a metal accounting report involves much more than just printing it (Lachance, Leroux, & Gariépy, 2015a). The underlying metal accounting system (Figure 1) is responsible not only for the reliable production of the metal accounting reports but also for the quality of the outcome. As such, the crucial tasks of its design/audit/retrofit should neither be seen as ancillary nor be left as an afterthought."

Jan 1, 2017

By G. Bridgstock, S. S. Forbes, E. M. Elkin

"OPERATIONS at Canadian Cop-per Refiners Limited, since the refinery was established in 1931, have been described in previous papers ( 1,2). Since then the refinery has treated the entire copper output of Noranda Mines Limited and Hudson Bay Mining & Smelting Company Limited. With the commencement of production in 1956 at Gaspe Copper Mines Limited, this copper has also been refined. From the start of operations to the end of 1958, the following had been refined: copper, silver, gold, selenium and tellurium.Construction of new buildings and additions to other buildings have been needed to handle increased receipts. The refining capacity has been increased from 112,000 tons of copper per year to a total of 236,000 tons per year.The refinery is located at Mont-real East, Quebec, close to railway and highway facilities. Incoming materials and shipments, with some small exceptions, are handled by rail. Some finished products are sl1ipped by industrial flatcar to the adjoining plants of Canada Wire & Cable Company Limited and Noranda Copper & Brass Limited."

Jan 1, 1960

By C. -S. Jiang

In most copper refineries, addition agents are added at predetermined rates with no further monitoring of their activity or concentration in the electrolyte. Increasingly stringent cathode quality requirements, and a desire for better process control in tankhouse operations, have recently directed a number of refineries to search for a better addition agent control strategy. Extensive development work has been carried out at the Noranda Technology Centre for the monitor in of glue and thiourea in copper refinery electrolyte using cyclic voltammetry (cv~. Data from both synthetrc and commercial electrolytes are presented, showing the ability of CV to produce reliable and easily identifiable fingerprints of addition agent concentrations in copper refinery electrolyte.

Jan 1, 1991

By Sherwin F. Kelly

THIS is intended as a simple review of the principles and practice of geophysics, so will not be of interest to the geophysicist, who is hereby warned of its elementary character. The engineers for whom it is written are those who, having glimpsed the formidable formulas and discussions of the geophysicists, give all publications on the subject a wide berth. For a few years now the geo-physicists have had a tendency to be ingrowing at their meetings, going deeper and deeper into theory and instrument construction, and forgetting to present the topics that would interest the practicing engineer who desires merely to know how geophysics can help him, not why.

Jan 1, 1934

By Robert Bissonette, Samir Sbai

A critical component of implementing autonomous systems is the ability to use information from a robust sensory and information system to make sound, predictable, and repeatable decisions to assure safety. This means that any such system would need to evaluate what objects (people, equipment, boulders, etc.) of interest exist in that environment (with relevant data about identity, trajectory, characteristics, etc.), project a future continuum of those objects (including considerations for variabilities), and make control intervention choices to minimize risk due to exposures in the present operational area. The components of an overall system would include: a) sensor and data fusion, b) probability projection of future states, c) generation and evaluation of alternate futures, and d) implementation of best course of action to reduce risk. The National Institute for Occupational Safety and Health (NIOSH) Spokane Mining Research Division (SMRD) is studying this framework for applications for autonomous mining equipment. This paper focuses on using information from the sensor fusion engine to generate a continuous projection of future and alternate states (b and c above) incorporating the factors of confidence, accuracy, tolerance, and other variabilities. We refer to this as Machine Situational Awareness (MSA).

Jun 25, 2023

By T. Nghipulile, G. Dzinomwa, J. Kurasha, M. Amwaama, B. Mapani, K. Maweja, T. E. Moongo

The effect of mineralogy on the grindability was investigated using three copper ores – two sulphides and one oxide. The dominant copper minerals were identified by optical microscopy and mineral chemistry derived from SEM-EDS analysis. The sample designated sulphide 1 was borniterich, sulphide 2 ore was mainly chalcopyrite, and the oxide ore was predominantly malachite and minor azurite. The gangue minerals were identified using semi-qualitative XRD analysis. Sulphide 1 contained more than 80% (w/w) of quartz compared to about 70% in the other two ores. The Bond work indices were 13.8, 21.6, and 17.3 kWh/t for sulphide 1, sulphide 2, and oxide ore respectively. This suggested that the chalcopyrite-rich ore is the hardest, while the malachite-rich ore has intermediate hardness, and the bornite-rich ore is the softest. The brittleness indices of the ores were calculated using the chemical composition of the gangue, and a good correlation between brittleness indices and Bond work indices was observed, which highlights the importance of the gangue composition in determining the fracture behaviour of the ores. There is scope for further investigation into the relationship between ore mineralogy and comminution behaviour using other breakage characterization techniques.

Mar 30, 2023

By Scott Turner

HOSTS of friends will rejoice that T. A. Rickard has been given honorary membership in the Institute. It might well have been done long ago, since, when one reviews distinguished services rendered by individuals to our organization and our profession, it is at once apparent that his name ranks high and that he has merited this distinction for more than three decades. Our by-laws restrict this list to twenty names; "T.A." becomes the sixteenth living member. Young engineers should particularly be pleased; Mr. Rickard has had a career rich in human interest, and full of useful suggestions to the younger men; he has given them good advice and set them a notable example; he, more than anyone else, has shown them how technical writing can be clear and concise; he has inspired youngsters to do their best; he has been their friend. No one has more first-hand knowledge of these facts than the writer of this appreciation:

Jan 1, 1935

By L. J. Defferding

This report documents the work performed by Battelle-Northwest and its sub-contractors in Phase I of a project to develop a cross pit conveyor system for the Bureau of Mines. The conveyor system description includes details of the conceptual design as well as system and component specifications. The selection of primary and back-up sites for system demonstration is discussed. Maneuvers and operating sequences required for mining the selected demonstration site are described and illustrated in detail. Economic viability of the cross pit conveyor system was analyzed by estimating the cost of overburden removal per ton of coal using the Battelle-designed concept and comparing these costs to the cost of an available state-of-the-art 30-yd3 dragline operation. Testing and trade-off studies conducted are documented and the results presented. Alternate designs considered in developing the selected cross pit concept are included for completeness. Based on the evaluation of the selected concept, it was concluded that the cross pit conveyor system proposed by Battelle is a technically and economically feasible overburden handling method with a good potential to improve western coal mining efficiency.

Jan 1, 1976

By Mark W. Booth

THE Dominion Steel and Coal Corporation, as a coal mining concern and as a steel industry, has much pumping to do, and the conditions are as varied as it is possible to make them. We are faced with handling large quantities of water at low heads, and small quantities of water at high heads. We have fresh water, we have salt water, and we have highly acidulous water (see Table II). Our pumping problems are concerned chiefly with mechanical reliability, continuous, reliable operation, first cost, and operating cost. The Corporation is actually expending more than 15 per cent of its power consumption at the mines in pumping water, and at the steel plant about 17 per cent; that is to say, 16 per cent of the Corporation's entire power consumption goes into pumping water ( see Table I). We are pumping out of the mines 2 ½ tons of water for every tan of coal that is produced. At the Steel Plant, we are pumping 188 tans of water for every ton of steel we produce. (See Tables III and IV). The mine is pumping at high heads, up to as high as 1,400 feet in one lift ; in the Steel Plant it is, fortunately, at lower heads, 250 feet or 110 lb. being the general maximum. It behooves us, therefore, to look into the question of efficiency. In whatever direction we can gain something, it will be worth while. The centrifugal pump is not an adaptable machine. That is, a pump designed for some particular location and purpose will not always work efficiently if installed in some other place and used for some other purpose. It must generally be designed for the particular job it has to do. Reciprocating pumps are not so sensitive. We have Cameron plunger pumps that can be set up almost anywhere in a mine and they will work, but for big jobs they are apt to be clumsy and the driving power becomes a factor- which is, in fact, the controlling factor in deciding the type of pump we use. One disadvantage of the a.c. induction motor, however, is that its speed cannot easily be controlled. At its rated speed and output, it is a highly efficient machine, but, with any change in these, its efficiency goes all to pieces.

Jan 1, 1944