Search Documents

By D J. Brake

The risk from fire remains one of the most serious of underground mine disaster scenarios. The impacts of mine fires on the underground ventilation system and the production of toxic gases have been difficult to model and therefore assessments have relied largely on empirical data, historical precedent and subjective opinions. Underground fire modelling software has had limited availability and been technically challenging and time consuming to use especially for routine mine investigations. There has also been no well-accepted set of assumptions for fire modelling in mines, which has resulted in a lack of confidence in adopting its use more widely. This paper describes modelling of three critical fire scenarios in underground hard rock mines: a fire (LHD) in an underground diesel refuelling facility, a fire in an underground explosives magazine and a fire on an underground ore transport conveyor. Modelling was undertaken using VentsimÆs VentFIREÖ fire simulation module. It describes the basis of design, the key assumptions, the methodology used and provides examples of the outputs, conclusions and recommendations. It reviews the impacts of these fires on egress and entrapment strategies in the mine. Some general principles regarding improvements to ventilation circuit design based on this analysis are also recommended. Whilst the fire scenarios were based on actual case studies, they have been disguised for this paper.CITATION:Brake, D J, 2013. Fire modelling in underground mines using Ventsim Visual VentFIRE software, in Proceedings The Australian Mine Ventilation Conference , pp 265-276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By BruneJurgen F., Richard C. Gilmore, Matthew Schreiner, Ray Johnson

Explosive pockets of methane-air mixtures accumulate in underground coal mines and, when ignited, produce an air-blast wave that can disturb combustible coal dust on the floor, roof, and ribs. To prevent explosions, the coal dust must be continuously diluted through application of inert rock dust, usually powdered limestone. Application of powdered dust process creates a respiratory nuisance downwind, where miners cannot work until the dust settles. Rock dust suppliers have developed wet and foam applied products to reduce the nuisance and limit the interruption to mining during dust application. To test the effectiveness of these alternative dust products, researchers at the Colorado School of Mines (Mines) have constructed a full-scale explosion test drift located at the Mines Edgar Experimental Mine (Edgar) to study the dispersibility of different rock dust applications. This paper examines the use of Pentaerythritol tetranitrate (PETN) detonating cord to produce controlled air-blasts that simulate methane-air explosions. The air blasts are generated with curtains of detonating cord that produce shockwaves with wind speeds between 30 to 70 m/s (100 to 225 fps) depending on the length of 5.3 g/m (25 grain/ft) detonating cord used. These velocities represent the minimum air speeds required to trigger propagating coal dust explosions. Researchers have conducted 40 test blasts with various lengths of detonating cord. Results show the two primary waves and two reflected waves each decaying into airblast waves with overpressures of 14 to 27 kPa (2 to 4 psi). Pressures were recorded with commercial piezoelectric transducers and custom-built, bi-directional probes to record the total and dynamic pressures of the wind generated in the explosion. Researchers were able to generate consistent and repeatable wind speeds and air-blast durations sufficiently similar to a methane-air explosion to study the dispersibility of various rock dust products and application methods

Jan 1, 2019

By M Salu

Ventilation control devices (VCD’s) and bulkheads are critical controls used for managing risk in underground coalmines. Following the Moura No. 2 mine explosion in 1994, the Queensland Mines Department required that the design of VCDs be based on live testing (such as in a mine testing explosion gallery) and more recently on numerical modelling using measured seal material properties. While the stipulated methods represent an idealistic solution, they are not practical to implement as solutions to daily challenges presented in underground coalmines.Not all VCD’s and bulkheads are placed in areas which have been mined to standard roadway dimensions. Operationally, VCD’s may be required to be placed close to intersections or require large dimensionally different areas (eg overcasts and pre-driven recovery road shutters) compared to the live testing or numerical modelling originally undertaken.This paper describes the various structural engineering methods utilised to account for the design of VCD’s where the operational requirements are non-standard. Siting and construction of VCD’s near the entry of cut throughs and geological structures requires additional design considerations. While VCDs constructed from a single material (eg sprayed mining plaster) are relatively straightforward to design, the addition of multiple openings (doors) or large pipes will complicate the structuralanalysis significantly.Temporary bulkheads used for the containment of grout such as for the construction of pre-driven recovery roads in coal mining have a significantly different risk profile to VCDs and should be designed accordingly. Recent failures and near-misses in such bulkheads have highlighted this issuefor the authors.The existence of an Australian Standard for Underground Mine VCDs and Bulkheads would go a long way to addressing many of the issues raised in this paper. Without a single, industry-accepted reference for VCD design, individual mines will have to continueto exercise their best judgements using whatever local expertise is available to them.

Oct 12, 2022

By G. T. Austin

Every year the United States consumes millions of dollars worth of abrasive materials as blasting media. Entrained in either a gas or liquid stream or propelled by paddles or wheels, they are directed onto the surface of another material to modify that surface. The modifications to impacted surfaces include cleaning, cutting, deburring, etching, finishing, and peening. Blasting media can be either organic or mineral abrasive materials. Information and data presented are for only a portion of the mineral abrasives, they are; fused aluminum oxide, coal slag, copper slag, garnet, metallic shot and grit, nickel slag, olivine, silica sand, silicon carbide, and staurolite.

Jan 1, 1994

By Melissa S. Beauregard, Randall A. Pietersen

This study focuses on quantifying the effects of water infiltration on a full-scale energy pile system’s ability to meet the thermal demand of an HVAC system. Theoretically, an energy pile system should increase its thermal capacity after a rain event due to increased moisture content creating an increase in thermal conductivity of the surrounding soil matrix. The United States Air Force Academy has an energy pile research site consisting of 8 full-scale energy piles located below a shower facility. The local colluvium surrounding the piles allows for relatively high water infiltration during rain events. This study uses an 11kW Precision Geothermal Geocube to apply a thermal load on two single-loop piles. A weather station located south of the structure records atmospheric conditions. Results indicate that moderate rain events can caused up to a 23% increase in the system’s thermal exchange capacity. This change is due to the increase in moisture content near the surface, which penetrates to deeper soil layers with time. The time required for moisture to penetrate to greater depths and then dissipate in the soil matrix, explains why increased system performance is seen for over a week following the passing of a singular rain event. 1 INTRODUCTION With a “future-forward” focus, there is an ever-pressing economic and environmental need to use sustainable sources to meet growing energy needs. HVAC is typically responsible for 34% of the overall energy required by commercial buildings and 48% of the energy required by residential buildings (USEIA, 2009; USEIA, 2012). Energy piles are a low cost, sustainable technology that have been used to offset this energy demand incurred by a building’s space heating and air conditioning requirements. An energy pile consists of heat exchanging elements in a closed loop system integrated into a building foundation and connected to a ground source heat pump (GSHP). It is most common for these heat- exchanging elements to be constructed within a drilled shaft foundation due to both construction practices and geometric considerations. This system operates based on the principle that at a certain depth below ground (typically 4 meters) subterranean temperature remains constant at a value equal to the mean annual air temperature at a given location (Kavanaugh et al., 1997). This allows the soil to function as a heat sink for cooling operations and a heat source for heating operations when exchanged within this zone of relatively constant temperature. For the past 25 years, the implementation of energy pile technology in public, residential, and even large-scale architectural complexes has slowly expanded which has created an increase in research into the topic as a result (Brandl, 2006; Hamada, 2007; Sekine et al., 2007; Gao, 2008; Bourne-Webb, 2009; Stewart and McCartney, 2013; Murphy et al., 2014). When pile construction takes place beneath the groundwater table, soil is under fully saturated conditions, maximizing thermal exchange for a GSHP system. Under unsaturated conditions, however, changing moisture contents change thermal conductivity values in a soil, which affect a GSHP system’s ability to meet a thermal demand. The observational data presented in this paper apply to GSHP systems in unsaturated soil conditions.

Jan 1, 2019

The optimal production of the metals needed by society is best achieved by a close synergy between concentrate production and smelting. For over 75 years commencing in 1923, such a close relationship was enjoyed between the Sullivan Mine in Kimberley, British Columbia and the Trail zinc-lead complex. An effective program of continual change and improvement at the Sullivan concentrator was achieved through a strong entrepreneurial spirit. This spirit was in part maintained through a favourable location in south-eastern British Columbia that resulted in a dynamic local community that has survived the closure of the mine. Innovations to be reviewed include feed forward reagent control, the use of column flotation to zinc and lead cleaning and the application of ultrafine grinding coupled with concentrate dewatering using hyperbaric filter technology.

Jan 1, 2005

By R. T. Rudd

DISCUSSION R. T. RUDD I have the following comments on Mr Bosman's paper. Before giving the company permission to discharge neutralized mine drainage containing 1800 mg/l of dissolved solids into a public stream, my Department had to consider the matter from both the legal and the practical viewpoint.

Jan 4, 1974

By J. D. McLenegan

The purpose of this investigation was to prepare a market survey of the refractories industry in California and Nevada (referred to in subsequent paragraphs as the region), and to determine the degree of self-sufficiency and the potential capacity for anticipated growth. The report includes estimates of the total annual refractories consumption, the quantity of refractories imported into the region, the tonnage of raw materials required for their manufacture, and the resources of fire clay and high-alumina minerals in the region.

Jan 1, 1956

By W. R. Smith

Introduction No commercial deposits of silica sand are known to occur in British Columbia, so all requirements for foundry and other uses must be imported. During the war, nearly 5,000 tons per year were used, all originating in Illinois and delivered to local consumers for about $12.00 per ton. Present requirements are somewhat less, but the cost is still of the same order. The relatively high cost of silica sand in British Columbia is not only a serious item for present consumers, but might be a deterrent to the establishment of a glass industry, should this be contemplated at any time. The present investigation was undertaken in an attempt to provide a cheaper source of silica sand within the Province. In 1936, a large number of beach and bank sand deposits in the lower coastal region of British Columbia were examined by the British Columbia Department of Mines, and samples were analyzed chemically and mineralogically. The deposits over the whole area proved remarkably uniform in mineral composition, consisting essentially of quartz, feldspar, ferromagnesian minerals, rock fragments, and various accessory minerals, and differing only in the relative proportions of the various constituents. In no case did the quartz content of any sand exceed about 40 percent and the average was of the order of 20 to 30 percent.

Jan 1, 1947

By J Ledgerwood

Namakwa Sands is a mineral processing company based on the West Coast of South Africa and is solely owned by Exxaro Resources Limited. Mineral ore is mined and processed, concentrated and both chemical and mechanically upgraded before being sent for electrostatic and magnetic separation units. The final high value mineral products report as Zircon, Rutile and Ilmenite.The recovery of non-magnetic material is largely dependent upon a number of factors, including but not limited to dew point, ambient temperature, feed rate, mineral size distribution, specific gravity and mineral content in head feed. One important limiting factor to recovery in typical dry mill operations is the particle size distribution of the feed. Variance in the particle size has catastrophic consequences for recovery. This is the reason for this study. Until recently large variances in non-magnetic production were viewed to be a function of machine operation. This view was later rejected with the feed size distribution determined as the major driver of low recoveries, for Namakwa Sands orebody 50 per cent variance in particle size distribution can be noticed within one day. This is because of the successive mining blending techniques employed.The predicament is that the two modes were so closely placed together that recovery of a single mode is almost impossible without the consequence of greatly reducing recovery. The second mode was found at 125 µm while the first was at 90 µm. Interestingly, for the mentioned feed type a cumulative size distribution of a unimodal feed type is almost exactly the same as for a bimodal size distribution. Thus a plot of cumulative size distribution will show no difference due to the modes being so close together. This is the reason why this phenomenon was not noticed before.The study also found that, using an high tension roll (HTR) or rare earth roll, a fine stream with a single mode at 90 µm versus a coarse stream with a single mode at 150 µm would yield completely different results interms of yields. Larger conductive particles are thrown from the roll while small particles loose charge faster (entrainment). Results in terms of the bimodal size distribution show that even though 25 per cent of the feed type is greater than 150 µm the yields followed a similar pattern to that of the coarse particles rather than that of the majority (75 per cent) fine particles. This confirms what was published by M Ziemski and P N Holtham in 2005 on charge decay rates; they mentioned that particle bed effects played a major role in recovery.

Oct 5, 2011

By A. M. Kiwior

In 1969, the Congress of the United States declared that "the first priority and concern of all in the mining industry must be the health and safety of its most precious resource - the miner," Therefore, Public Law 91-173, Federal Coal Mine Health and Safety Act of 1969, was enacted. Since haulage accidents account for a high percentage of coal mining accidents, Section 314e, ?Hoisting and Mantrips,? was included in the law. This section states: "Each locomotive and haulage car used in an underground coal mine shall be equipped with automatic brakes, when space permits. Where space does not permit automatic brakes, locomotive and haulage cars shall be subject to speed reduction gear, or similar devices approved by the Secretary which are designed to stop the locomotive and haulage cars with the proper margin of safety."

Jan 1, 1975

By Karsten Beekhaus, Sander W. Odijk, Rabea Bahlum, Mazin Adnan, Ayman Abdelh Al Nuaimat, Hassan Farhat

The Arab Potash Company, APC, is one of the 10 largest potash producers of the world. The solar ponds at the Dead Sea, used for the enrichment of the salt content in the brine, are of crucial importance for the first step in the exploitation of the potassium salt. Targeting at the expansion of production in the since over 50 years utilized facilities, the increase of the brine exploitation capacity, reducing the substantial brine seepage losses from the ponds, becomes a crucially required measure. In this context, the remediation measures on the over 11 km long Dyke 1, being a main dyke of the solar ponds system, became inevitable to reduce the brine losses, prevent further development of sinkholes and cavities and hence assuring the stability of the dyke. The highly aggressive environment, the acting hydraulic conditions and the sensitive stratification and nature of the existing ground represented remarkable challenges for the design, as well as its implementation by the construction activities. Royal Haskoning developed a solution addressing the challenges above and targeting at a high sustainability of the executed structure, especially in view of the various geological and hydrological hazards repeatedly occurring in this Dead Sea region, including sinkholes of several meters by diameter and depth. The construction works, consisting of a cut-off wall, with depths reaching down to 31 m, were awarded to Bauer International FZE, a subsidiary of Bauer Spezialtiefbau GmbH. Upon the execution of the first section of 4.2 km length, additional sections were subsequently commissioned, also on further dykes, totaling to about 300,000 m² of cut-off wall. The specific project conditions, such as utilization of cutter technique for the excavation in Halite rock, the stability of open trench exposed to hydrostatic pressure of salt-saturated ground water, resulted in unconventional requirements towards the supporting fluid. The extremely aggressive saline conditions –with a Dead Sea water density of 1.25 tons/m3; one of the world's saltiest water–, were further a decisive factor for the definition of the backfill material concept. Despite its clear advantage for construction of cut-off walls with installed sheet piles, the single-phase system with hardening slurries, fulfilling both functions of excavation support and cut-off wall backfill material, had to be abandoned in favor of the two-phase system, to construct a hybrid cut-off wall made of sheet piles and plastic concrete.

May 1, 2022

By S. M. Moore

Each year more than 400 coal miners are injured (fatal and non-fatal) by rock falling from between or around roof supports. Many of these injuries could be prevented by the installation of roof screen (wire mesh). However, many coal mines may be reluctant to use roof screen because of the added cost. The goal of this study was to determine the potential saving in workers? compensation (WC) premiums that could be achieved due to a reduction in rock fall injuries after roof screening. The WC rate-setting methods utilized by IL and KY were investigated in this study. Using actual data obtained from MSHA, national and state WC bodies and individual insurance companies (e.g. average cost per injury, loss cost rate, number of injuries per year, number of injuries preventable each year with roof screening), hypothetical mines (representing two mine sizes: 67 and 150 employees) were constructed with realistic ranges for estimates of injuries and WC premium costs. Using each state?s actual WC rate-setting formulas, total savings in WC costs after a three-year period were determined. Across both states, savings in WC premiums ranged from 1.8% to 14.6% when injuries were reduced by 10% to 20%. Additionally, an economic analysis was performed for an existing mine consisting of 67 employees. For this mine, the annual cost of a roof screening program was estimated at $240,000. If the screening prevented 13 ?struck by? WC claims over a 3-year period at this mine, the reduction in WC premiums alone could pay for the entire screening program.

Jan 1, 2010

By I. Tinto

"IntroductionEnvironmental pollution problems, caused by gases or effluents, by high noise levels or from air borne dust, are placing increasing demands of the operators, from statutory authorities, and from the general public, to adopt more stringent dust control measures. This requires that a successful plant dust control program be an integral part of any plant operation. While a successful environmental program is a key factor in maintaining productivity and good labour relations, anticipation of future environmental regulations during the plant design phase can avoid the high cost of plant upgrading, or dealing with pulmonary conditions in the work force in subsequent years.Particulate removal, conventionally called dust collection, involves the removal of coarse- and fine-particulates from the airstream. Although generally limited to that required for contro!Hng plant generated air emissions, particulate control equipment also has a wide application for air cleaning and filtration inside the plant, as well as for recovery of usable products.In the late 1950s and early 1960s the public became more concerned with the problems of air pollution. This increasing concern was stirred by an awareness of the extremes to which water pollution had progressed in many of the rivers and lakes, by increasing perception of air pollution as detected by visible smog and harsh chemical odors, by the alarming rate of increase of smog plagued cities and communities, and by specific incidents where ill health could be traced to specific episodes of air pollution. Particle size is perhaps the most important single factor affecting particulate control. Large particles (over 5 microns) constitute the major mass fraction of most sources of emission and economical control equipment dqes exist for their efficient control. However, while these larger particles frequently represent the source of soiling and unsightly smoke plumes, they are not a major health problem as they tend to settle relatively quickly, are more easily scrubbed from the atmosphere by rain, and are not able to penetrate the respiratory system. By far the most important form of particulate air pollution is the fine particulate, (below 3 microns) which is harmful to the pulmonary system. The adverse effects caused by this particulate matter on human health are for the most part related to injury to the surfaces of the respiratory system. Particulate material in the respiratory tract may produce injury itself, or it may act in conjunction with gases, altering their sites or their modes of action. A combination of particulates and gases may produce an effect that is greater than the sum of the effects caused by either individually (i.e. synergistic effect)."

Jan 1, 1989

By Joël P. T. Kapusta, Romeo U. Pagador, Noparut Wachgama, Chumnoom Khuankla

"Thai Copper Industries (TCI) is a custom copper smelter and refinery in Rayong, Thailand, with an annual capacity of 165,000 tons of cathodes. It employs the El Teniente Technology as the primary smelting reactor to produce white metal from copper concentrates. The white metal is further treated in Hoboken Siphon Converters to produce blister copper then refined in anode furnaces before being cast into anodes for electro-refining in the on-site tankhouse.Thai Copper Industries is the first copper smelter to install and successfully operate on a commercial scale with the Air Liquide Shrouded Injection (ALSI™) Technology in the Hokoben converters with sonic injection of oxygen enriched air and nitrogen for cooling of the injector tip areas. Following commissioning and the establishment of operating practices, the performance of the Hoboken converters with ALSI™ Technology produced outstanding results. The unique combination of an El Teniente and Hoboken siphon converters, both of which are bath smelting operations, offers very high blowing and oxygen efficiencies. As a consequence, reverts recycling was accelerated with minimal build up on the mouth, end-plates or even below the siphon that is typical in Hoboken converters.These outstanding results in the Hoboken Siphon Converters with ALSI™ Technology helped the TCI Plant reach a production of about 75% of its capacity within four months despite the fact that the TCI staff is quite young and its converter know-how and experience are not yet fully developed."

Jan 1, 2009

By Donald J. Donahue

Ladies and Gentlemen: As we begin these three crowded days of technical and economic discussion of problems faced by mining and metallurgical engineers, it seems appropriate at this Keynote Session to consider the future of this industry from which we derive our livelihood, It is also appropriate at this international meeting to view our industry on a world-wide basis. First, let us assess the world's future needs for minerals - the needs which it is our industry's task to meet. Next, let us look at what supplies of minerals may be available to meet those needs. I will speak of this first in terms of the physical availabilities of minerals. Finally, we can consider some of the social or institutional factors which will condition the world's mining industry as it goes about its task of discovering, developing, producing, and delivering the minerals needed to meet the world's demands. Let me give you a foretaste of my conclusions. First, future world demands upon our industry will be enormous, eclipsing anything that we have known up to this point. Second, there is strong evidence that our earth's crust contains a sufficient physical quantity and variety of minerals to meet forthcoming needs for as long a period ahead as one can envisage.

Jan 1, 1974

The value of U.S. mineral raw material output reached a record $63.1 billion in 1975. This high exceeded the 1974 value of $55.2 billion by 14 percent. Among the three major mineral categories -fuels, metals, and nonmetals -only fuels showed an increase in value. Both the metal and nonmetal categories showed declines in value. The significance of this nearly $63 billion mineral output can be noted in the fact that it is the basis for the subsequent production of over $270 billion a year in energy and processed materials. Of the 78 individual mineral commodities included in these 1975 totals, only 17 registered gains in output, while 45 registered value increases, reflecting higher prices.

Jan 1, 1976

By Y. M. Shneerson, V. M/ Shpaer, E. E. Zhmarin, A. Y. Lapin, E. M. Vigdorchik

This paper describes studies of zinc concentrate oxidizing pressure leaching using the method of mathematical modeling. The concept of a kinetic function was taken as a basis for mathematical modeling of the leaching process. The kinetic function describes dependence of the unreacted component share OJ on the relative time x (the relative time is the ratio of the test duration and the time of complete dissolution). This kinetic function is determined in accordance with the results of batch laboratory tests. The laboratory tests have been carried out on zinc concentrate produced from Kazakhstan zinc-copper ores. Zinc concentrate consisted mainly of three types of minerals: sphalerite (70%), pyrite (13%) and chalcopyrite (10%). Oxidation reactions of sphalerite, pyrite and chalcopyrite have been considered as principal ones. The kinetic characteristics of the process (kinetic function, reaction order, activation energy, duration of complete dissolution of the concentrate components) have been calculated in the course of laboratory tests. The mathematical model was used for estimation of the main technological leaching process parameters (such as process rate, degree of metals extraction, autoclave capacity, heat balance, etc.). Mathematical modeling based on the kinetic function concept allows safe designing of metallurgical equipment and scaling the technology to industrial capacity.

Jan 1, 2004

By G. J. Conroy

This Bureau of Mines study was initiated to determine whether or not a large-scale investigation of 400-Hz applications in coal mines was justified as a means of increasing safety in operations due to size and weight reductions in portable and other mining machinery. Potential uses for 400-Hz power in mining operations are explored, and cost and size comparisons with 60-Hz systems are made. The use of variable-frequency motor drive is suggested for conveyors. The conclusion was reached that there is no significant potential safety increase due to a general size and weight reduction, as the fact of such general reduction cannot be demonstrated.

Jan 1, 1974

By Edgar Urbaez

Production scheduling is one of the most important factors affecting mine planning. A program -Mine Scheduler -that aids mining engineers with the setup of an optimum open pit production scheduling algorithm has been developed. A mathematical model for open pit scheduling that optimizes the Net Present Value of the cash flows was formulated. A simulated data is formulated as a Mixed Integer Linear Programming (MILP) problem. What's Best by Lindo Systems is used as the MILP solver in Microsoft Excel. The implementation of the algorithm focuses on problem setup, allowing users to easily evaluate, simplify, and develop the model that best fits their production scheduling.

Jan 1, 1999