Search Documents

By R. P. Fischer

The Colorado Plateau region has been the principal domestic source of uranium, vanadium, and radium. The value of these commodities produced from the region through 1964 slightly exceeds $2 billion. Most of the deposits occur in streamlaid lenses of sandstone in the Chinle and Morrison Formations. The ore minerals below the zone of oxidation are low-valent oxides and silicates of uranium and vanadium; all of these, except the quite stable vanadium silicates, oxidize readily to a variety of high-valent uranium and vanadium minerals. The ore minerals partly replace fossil wood but mainly impregnate sandstone, typically forming tabular ore bodies that are nearly concordant to the bedding of the host rock. The deposits range in size from those containing only a few tons of ore to those containing more than 1 million tons. Stratigraphic, lithologic, and sedimentary structural factors obviously influenced the localization of these deposits, but igneous activity, hydrothermal mineralization, and tectonic structures show no similarly consistent influence on localization. The deposits are epigenetic, but the source of the ore metals, the nature of the ore-bearing solutions, and the time of ore emplacement are uncertain. A few uranium deposits in the region are dominantly discordant to bedding and occur in collapsed breccia pipes or along linear fractures. Their origins are also uncertain.

Jan 1, 1968

By Bruce Macdonald

Operational reservoir management activities such as cyclical steam, water or CO2 injections frequently cause surface micro-deformation. InSAR monitoring from space based sensors of this surface deformation has become a valuable approach to confirm and monitor extraction and injection activities. Sequestration of CO2 into deep saline aquifers is discussed as an important long term solution to slow future climate change. This method requires reliable continuous monitoring to assure that captured CO2 is sequestered in the substrate for ?all time? (typical minimum requirement by law is 20-30 years). We have shown that combining flow and deformation modeling with spaceborne synthetic aperture RADAR interferometry (InSAR) measurement of ground uplift caused by the underground release and spreading of the CO2 can be forged into a powerful tool to monitor sequestration. We used a novel InSAR approach to resolve the surface motion over the In Salah, Algeria CO2 sequestration site. Our approach exploits all information contained in an interferometric stack by exploiting both persistent distributed as well as persistent point scatterers. Displacement time series are obtained with a network inversion approach applied after topographic error and preliminary atmospheric correction of the network (dual-scale technique). After inverting the original network data to common master we then use an advanced spatio-temporal filtering scheme to remove the remaining atmospheric phase components down to scales of 1 km or less. By comparing final displacement series from multiple interleaving InSAR stacks we show that the accuracy of our refined solution to detect uplift outside of significant temporal data gaps in the InSAR stack is significantly better than 1 mm per year. We further show that accuracy and robustness to data gaps are both significantly improved by co-inverting multiple datasets with the same and different sensors. This co-inversion method also allows the seamless continuation of the monitoring from one sensor to another.

Jun 1, 2012

By R. J. Heath

Potassium, together with nitrogen and phosphorous, is one of the essential nutrients required for growth. All living things need potash and so the major demand for potash (approximately 95% of, total demand) is as a fertilizer. Traditional agricultural techniques relied on the return of organic materials to the soil to provide nutrient requirements and maintain soil fertility, and the prevailing low crop yields required little in the way of added fertilizers. But agricultural productivity has increased dramatically in recent times, and this increase in crop yields requires substantial amounts of added nutrients to keep the soil fertile. It follows that there will always be a demand for potash. There is no substitute. Other fertilizers that contain N and P are complementary and not competing products.

Jan 1, 1987

By Oliver Bowles

THE most important non-metallic mineral industries from a tonnage standpoint are those that are allied with the construction industries and are engaged in handling sand and gravel, crushed stone, building stone, cement, lime and gypsum. The greatest problem facing a number of these industries at this time is over-production. They have experienced un- usual, and in some instances phenomenal, growth during recent years, stinlulated by extensive highway and building construction, but in some localities expansion of producing plants has far outstripped industrial needs. The cement industry is operating at about two- thirds capacity. Over-production tends toward price- cutting and unprofitable and interrupted operation, involving maintenance expenses for idle plants and disorganization of working forces. This condition has encouraged active efforts toward reducing production costs by the introduction of labor-saving equipment. Also, there is a tendency toward the location of manufacturing plants, wherever possible, near the centers of consumption rather than at points of production of raw materials. In order to reduce overhead expense, or for other reasons, many consolidations of companies into larger units have taken place. An economic study of conditions in these industries is highly desirable. The U. S. Bureau of Mines has taken one step forward in this direction in the issuance of Economic Paper 7, entitled "Economics of New Sand and Gravel Developments." Briefly, this report emphasizes the importance of making a thorough study of all the economic factors involved before undertaking new .enterprises.

Jan 1, 1930

By Fei Dai

Musculoskeletal disorders (MSDs) are a group of painful disorders that affect muscles, tendons, nerves, joints, cartilage, and ligaments. They are a serious problem among the workforce in the United States. In the construction industry, high physically demanding tasks expose construction workers to a number of well recognized MSDs risk factors such as repetitive motion, high force exertion, and awkward body posture. Finding ways to effectively identify and evaluate risks of MSDs can significantly alleviate this problem. To this end, this paper reviews state of practice and research in the assessment of risks of MSDs among construction workers, in which a number of biomechanical models have been developed to evaluate joint and tissue loading with the aid of state-of-the-art remote sensing technologies. Findings from the review reveal that despite the advances in tracking human motion and muscle activities, current remote sensing approaches still involve sophisticated instrumentation and expensive experiment setup. These factors greatly limited the applicability of such approaches in real construction settings. How can we detect and evaluate the construction worker?s MSDs risk in real work environments? In this paper, strategies by utilizing video surveillance systems are presented, to set the stage for addressing the above question and discussing future research in real-time, marker-less, and costeffective MSDs risk assessment.

Aug 1, 2013

By T. H. Etsell, P. Kerr

Over the past 50 years, there have been a number of geological, mineralogical and metallurgical studies carried out on the Clear Hills ironstone deposits in northern Alberta, Canada. Due to the low grade and complex mineralogy, previous metallurgical studies have achieved limited success. After rejecting some of the more ‘conventional’ techniques for iron ore beneficiation, the authors chose to investigate the grain enlargement/iron segregation process for the beneficiation of the Clear Hills ironstone. The segregation reactions for iron have not been explored in as much detail as they have for copper and nickel. Iron segregation roasting involves the addition of a carbonaceous reductant and a chloride transport agent to an iron oxide ore, and heating the mixture to an appropriate temperature. The benefit of this process is that it allows ores in which the value minerals are intimately associated with gangue minerals to be processed in circumstances where conventional iron ore processing techniques are not suitable or capable of upgrading the material. As iron is one of the few elements that can be transported through this process, a clean high purity metallic concentrate can be achieved.Through the use of crucible testing followed by Davis tube magnetic separation, scanning electron microscopy, X-ray diffraction and atomic absorption spectroscopy analysis, characterization of the reaction products has been made with an improved understanding of the reaction mechanism.

Jan 1, 2015

By Roscoe W. Stensrud

The Marcona Corporation was established in 1965 to consolidate the ownership and management of the Marcona group operations. This company, with headquarters in San Francisco, has the following principal operating subsidiaries: Marcona Mining Company, formed in 1953, conducts iron ore mining, beneficiation and pelletizing operations in Peru. Cia. San Juan S.A., Panama, which contracts for sale and delivery of iron ore from the Marcona operation in Peru and from Mount Goldsworthy in Western Australia. Sari Juan Carriers, Ltd., a subsidiary of Cia. San Juan which owns and charters vessels for the bulk ocean transportation of iron ore, petroleum products, coking coal, slurry, salt and other commodities.

Jan 1, 1968

In 1991, the USBM (U. S. Bureau of Mines) evaluated the mineral resources of the 174,550-acre Bear Creek-Poker Peak area. Located 40 air miles east from Idaho Falls, ID, the study area is in the Caribou National Forest but is mostly administered by Targhee National Forest. USBM personnel mapped and sampled mines, prospects, and mineralized sites in and near the study area. Five types of mineral occurrences were identified in the study area: phosphate, limestone and travertine, placer gold, coal and uranium (the latter contained in the coal), and oil and gas. The study area has a high potential for oil and gas; evaluation of these commodities were beyond the scope of this study.

Jan 1, 1992

By G D RICHMOND, Campbell J. J

Aberfoyle Limited has developed the Hellyer complex base metal sulphide deposit located in North West Tasmania. As part of exploration and feasibility study, the ore was extensively tested, including trial milling, and was found to be very fine grained and to have poor flotation selectivity. Substantial innovation was required to produce saleable concentrates at acceptable recoveries and costs. Efforts were made to reduce operating costs, to improve metallurgical performance and to improve work organisation. These efforts were pursued both in design and in subsequent plant operation. This work has resulted in a very competitive operation with production costs in the lowest quartile of the industry. Examples of the measures taken are presented and the results are evidenced by improved plant performance since commissioning.

Jan 1, 1992

By R. L. Grayson, S. S. Peng

"Abstract. Sampling of respirable dust and analyses of samples have been partially completed for a longwall panel. Physical and compositional properties which have been characterized include:l. Respirable mass concentration, 2. Mineral composition,3. Particle size distribution by mineral,4. Particle shape distribution by mineral,5. Particle angularity distribution by mineral, and6. Respirable size distribution.Analytical techniques used in the characterization of samples are described, and results are reported with emphasis placed on relationships between the various characteristics and worker locations. Details of existing mining conditions, equipment arrangements, dust control methods and operating system parameters are presented.INTRODUCTIONThrough the work of many researchers worldwide, the health of coal miners in modern societies is now protected from dangerous exposure to respirable coal mine dust. A vast amount of research culminated in the exposure-response model of Jacobsen, et al. (1971) whi3h has been used to establish the 2mg/m exposure limit in the United States. According to the model, exposure to respirable dust for 35 years at this level or less would prevent the occurrence of a clinically significant case of coal workers' pneumoconiosis (CWP). The exposure limit, of course, must be adjusted whenever greater than five percent free silica exists in the respirable dust.The Jacobsen model was built around a mass concentration exposure, which showed the highest correlation with incidence and progression of CWP. As Morgan; et al. (1973) noted, howev.er, the quantity of respirable dust inhaled is not the only significant factor. It is noted that although mass of respirable dust correlates highest with the incidence of CWP, it is not a causal factor. Indeed, the insidious processes causing the disease occur on the cell-particle scale, requiring microscopic investigation."

Mar 1, 1989

By I R. F MacCulloch, K Jones

Pintail Systems, Inc, a Colorado USA based company has developed and commercially applied bioremediation processes for biological detoxification of cyanide compounds in mine waste. Site-specific microorganisms are isolated from spent ore, tailings or process solutions and augmented in the laboratory for cyanide oxidation, denitrification and metal biomineralisation. Biological processes typically treat complex contaminants (cyanide compounds, soluble metals and nitrates) in a fraction of the time of conventional remediation processes. Cyanide is used in microbial metabolic processes as a carbon or a nitrogen source. Biological detoxification processes applied at the end of mine life can end long-term liability and perpetual monitoring and containment. Case studies from commercial application and demonstration programs for the US Environmental Protection Agency will be presented in this paper.

Jan 1, 2004

By R. M. Smailer

Detailed description of the development of the FIOR process1 and, subsequently, other technical papers relating to the operation and start up of the FIOR plant2,3 are available in the technical literature. The Fluidized Iron Ore Reduction (FIOR) process plant constructed in the Matanzas region of Venezuela represents the first commercial application of this technology. The FIOR process was developed by Exxon Company during the 1950's and 1960's; and the facility in Venezuela was designed and constructed by Davy McKee with the plant start up in 1976. While there is a minority government ownership in the company, FIOR de Venezuela operates as a private sector company with the majority of the ownership being private capital.

Jan 1, 1981

By Stefan Mede

Robot Supported Moulding—this is the name of Herrenknecht Formwork’s entry to the world of automated segment production. What had been considered impossible for a long time, has been achieved by Herrenknecht experts together with the Swiss company Marti AG: unmanned segment production on the working line. The moulds open and close autonomously with the help of a hydraulic system. A robot cleans and greases the moulds at one work station and inserts the injection sockets at another. The next step will include further automation and digital networking of all processes from production to installation in the tunnel.

Jun 13, 2021

By B. M. Larsen

NEVER having actually tried to engage in the systematic education of anyone, and having little direct knowledge of the practical problems and limitations in the field of education, I can pose only as a "nonexpert" in this field, one whose ideas are to be regarded as personal opinions. The necessity for compromise between educational ideals and the practical limitations of time, money, and mental capacities of both student and teacher is evident in the preparation of an end product that we may regard with a reasonable degree of conviction as a professional engineer. We need to do so many things. The engineering student must have a clear understanding of the basic sciences; he should develop manual skills and co-ordination; he should speak and write the language with simple clarity and directness; he should gather knowledge of a special field; and, he should be educated for living in a broad ..

Jan 1, 1948

By B. Tonn, F. Kröger

"The continued development in engine technology is leading to an augmentation in power density which steadily elevates the requirements for thermally and thermo-mechanically highly loaded components such as cylinder heads and pistons. Due to these high performance requirements conventionally applied Al-Si alloys have reached their application limits, since their mechanical properties deteriorate quickly under the influence of heat. Improved applicability is given by Al-Cu-based casting alloys which have a superior high-temperature strength than Al-Si alloys. Since Al-Cu alloys exhibit insufficient casting characteristics, especially regarding hot tearing susceptibility and increased tendency for porosity, it is currently not possible to cast geometrically complex components in robust permanent mold casting processes. The further development of Al-Cu alloys is aimed at finding an optimum between improved castability while high-temperature strength and thermal conductivity are not deteriorated. It is known that a high amount of eutectic reduces the hot tearing susceptibility of an alloy, but it reduces thermal conductivity at the same time. In this paper it will be presented how the conflicting objectives – improved high-temperature strength, good thermal conductivity and reduced hot tearing susceptibility – can be brought together to develop an optimized Al-Cu alloy for application in permanent mold casting.INTRODUCTION At the beginning of the 21st century car, engine blocks were primarily made of gray cast iron (GJL). Less than half a decade later, the choice of material had shifted towards lightweight materials. Ever since, the car engine manufacturing is dominated by aluminum-based alloys. The weight of car engine blocks could thus be reduced by around 50% due to the lower specific weight of aluminum alloys compared to gray cast iron. Furthermore, the high thermal conductivity of aluminum alloys allowed a reduction of complex cooling channel systems and thereby promoted the advancement of this material group. The further development in engine technology leads to an augmentation in power density which elevates the requirements for thermally and thermo-mechanically highly loaded components. For example, in diesel-powered car engines the upper required limits can reach an ignition pressure as high as 230 bar and gas temperatures of up to 1000°C. Thereby, thermal loads can cause high alternating thermal stresses (Grzincic, 2003) which can effectively be reduced by providing high thermal conductivity."

Jan 1, 2017

By S. Kodama

Starting on a small scale, the equipment for processing synthesis gas to form liquid hydrocarbons was expanded to handle 100 m) 3/hr. This reactor was successfully designed and constructed, and a basis for future design methods was established. Because, however, this work was carried out on an empirical basis, it is felt that a more thorough theoretical study should be made in an effort to increase the efficiency of the process, particularly in the development of a simpler converter.

Jan 1, 1951

By Jason Rock, Rob Thompson, Lee Julian

This paper presents an innovative shift in inhibited bulk products with specific reference to their manufacture and application.

Feb 1, 2020

By Noel N. Moebs

This report summarizes a Bureau of Mines study on the use of geotechnology to identify and reduce ground control hazards at slate quarry operations in eastern Pennsylvania. The major ground control hazard is falling rock, attributed to weathered bedding plane faults, which weaken quarry highwalls. It was demonstrated that these faults can be detected outside of the quarry perimeter using surface resistivity measurements. Falls of ice from quarry highwalls constitute a second major hazard, which requires water diversion as a basic control method. In situ stresses seemingly cause only minor problems in slate extraction although they could interact with developed stresses and lead to failure of barriers between quarries. Pull tests showed that rockbolts anchor firmly in slate and should prove effective in securing loose rock.

Jan 1, 1986

By Jeffrey J. Daniels

Advances in borehole geophysical research for mineral assaying, and remote detection of mineralization away from the borehole. Nuclear activation measurement research has provided accurate in situ assays of economic metals with neutron-gamma activation, using a high resolution intrinsic-germanium detector. Although nuclear activation analysis is the present "best-hope" for obtaining in situ assays for some elements, gamma-gamma and magnetic susceptibility measurements can provide accurate assays for lead-zinc and magnetite, respectively. Borehole optical spectroscopy and x-ray fluorescence are being investigated as possible in situ assaying techniques for some minerals. More laboratory and field calibration research is needed before nonlinear complex resistivity (NLCR) can be routinely used as a quantitative assaying tool. Field tests have shown that variations in the local geologic environment can affect the quantitative accuracy of assay values from downhole NLCR measurements. Deeply penetrating borehole geophysical methods are increasingly being used for mineral exploration as drilling costs and exploration have increased. Borehole electrical measurements have been shown to be useful for detecting conductive orebodies that are not interesected by a drillhole. Hole-to-surface resistivity, and surface-to-hole time-domain electromagnetics are demonstrated to be particularly effective for defining mineralized zones in a massive sulfide environment. Borehole gravity meters and three-component magnetometers have been developed and should prove useful for defining geologic anomalies away from the drillhole.

Jan 1, 1985

By A. Slotwinski, R. E. Barry, M. M. Menon, P. T. Spampinato

"A coherent FM laser radar based sensor for remote metrology of plasma facing material surfaces in a fusion reactor is described. The sensor is capable of 3-D mapping of surfaces, based on a series of precise range measurements from large distances (up to 20 m). Other features include the ability to operate under adverse environmental conditions involving very high gamma radiation (3xI04 Gy/hr), ultra-high-vacuum (<I0-5 Pa), and high temperature (200°C). The paper describes the basic principles of the sensor, together with experimental results obtained with the sensor. The ability of the sensor for remote rendering of ""visual quality"" images without the need for any external illumination is also illustrated.IntroductionMeasurement of the features of large area surfaces (-1500 m2) to sub-millimeter accuracy, from relatively large distances (20 m), is necessary in the case of the International Thermonuclear Experimental Reactor (ITER -a 1500 MW fusion reactor that is currently in the design phase). Furthermore, the measurements may have to be performed after the reactor is temporarily shut down. During such shut-downs, the ITER in-vessel environment will be highly radioactive due to neutron activation of the reactor wall (gamma radiation field of 3xl04 Gy/hr), the vessel will be maintained under ultra-clean vacuum conditions (<10-5 Pa), and the plasma facing surfaces will be maintained at elevated temperature (200°C). Therefore, the precision measurements must be conducted remotely, and because of the large dimensions of the fusion reactor and the limited number of access ports, the measurements must be done from large distances. The reactor vessel is a large toroid. Fig. 1 shows the cross section of the toroidal vacuum vessel, and the location of the metrology probe. Because of the very large surface area involved, fast scanning capability is also needed to reduce the reactor down-time."

Jan 1, 1997