Search Documents

By P. Myllykoski, J. Nylander

"A commercial program package called Crownoff for the simulation of temper rolling in four high mills has been verified against measured data. The agreement between measured and calculated transversal strain distributions of the strip was found to be good. Effects of the strip crown and work roll bending force on the strain distribution were simulated. The results showed that when a single ground camber of work rolls is used for all strip widths; the strip crown should be parabolic, excluding the edge drop. An increase or decrease of the strip crown by 30 % during a coil can be compensated by a 2 to 5 t change in the work roll bending force. The ability to control the strip crown by work roll bending was insensitive to strip width. IntroductionCold rolled steel strips are usually temper rolled after recrystallization annealing, which follows cold rolling. The purpose of temper rolling is to suppress the yield point, finish the strip surface and correct possible flatness errors. The presence of a yield point might otherwise cause problems during subsequent forming processes. The in homogenous yielding in non-temper rolled steels leads to the formation of Lüders bands in the strip surface.The rolling force is influenced by the rolling speed and changes in frictional conditions in the roll bite. Therefore it is very important to plan carefully the mill settings and control algorithms during rolling. The purpose of mill control algorithms is to ensure constant reduction and the best possible strip flatness during the entire coil.Correctly predicting the rolling force is important for determining the mill presettings. Torque, forward slip and power requirements are not usually critical, if the reductions are small. However, the large elastic deformations occurring in the roll bite make the physical description of the process difficult. Physical rolling models developed for cold rolling contain assumptions that lose their validity as the reductions decrease to the level of one per cent."

Jan 1, 1994

By H. -Peter Sattler

The laser sorting technique for replacing the handpicking of the non-ferrous metal scrap from auto shredders was first introduced 1990, The process is based on the use of atomic emission spectroscopy induced by lasers to identify the scrap particles and sort them with adequate systems into main fractions of Al-, Zn-and Cu-alloys, stainless steel and lead, In the meantime the handling technique for the scrap, i.e. the singling and sorting technique as well as the analytical detector were further developed for more efficiency and higher reliability, i,e. less maintenance, minor sorting errors etc. These developments were mainly based, on and initiated by operational experiences from the startup phase of a first production plant. Part of the on going research work was the development of an ,aluminium detector which makes it the first time possible to sort mixed aluminium scrap automatically into specific alloy fractions.

Jan 1, 1995

The major components of sylvinite ores, sylvite (KCl) and halite (NaCl), are separated by flotation. Since both these minerals are water-soluble, the process is carried out in a saturated brine, 6~7 mol/L aqueous solution of NaCl and KCl. C16~C22 primary amines, utilized as a collector, are practically insoluble in water. In commercial potash ore flotation operations these amines are melted by heating up to 70~90°C. They are then neutralized with hydrochloric or acetic acids, and such a hot emulsion/dispersion is introduced to the flotation pulp (which is at room temperature). This is immediately accompanied by the appearance of a white precipitate in the system. As our measurements indicate, the Krafft point of dodecylammonium chloride in concentrated electrolyte solutions is much higher than 80°C, and the Krafft point of C16~C22 amines is substantially higher than that. Introduction of a hot amine emulsion into a pulp, at temperature much lower than the Krafft point for the utilized amines, must cause precipitation of the amines. Some of these species are obviously flotation-active. It is interesting to observe that in summertime, when temperatures are high-er, longer chain amines perform better. It demonstrates that the colloidal amine species that precipitate serve as active species in the potash flotation. Therefore, at higher pulp temperatures, when the temperature difference between the pulp temperature and the Krafft temperature of the utilized amine is not sufficiently large, a longer chain amine, the amine with a higher Krafft point, is more efficient. The results reveal that premixing of an alcohol such as MIBC (common frother) with the amine significantly improves flotation performance of the amine. In the presence of such an alcohol the amine disperse system becomes less turbid, and the rheology of the system less non-Newtonian. All this indicates that MIBC, which does not operate as a frother in a potash flotation system, when used as a co-surfactant, enhances the dispersion of the amine colloidal system. The appearing colloidal species perform as an active form of the collector.

Jan 1, 2014

El presente trabajo describe el sistema y los métodos para la extracción del oro en la planta de beneficio de Andaray Gold Mines, alcanzando una productividad óptima en el campo metalúrgico. La mina está situada en San Juan de Chorunga, provincia de Condesuyos, departamento de Arequipa, donde sus yacimientos mineralizados son de dos tipos: los yacimientos descompuestos que contienen limonita y oro libre, perteneciente a la mina Mercedes , y los de mineral piritoso aurífero, que comprenden chalcopirita y ojos de galena, perteneciente a la mina San Juan. El proceso de explotación se inicia con el transporte del mineral hasta su descarga en la parrilla de apertura. E mineral que no pase por la parrilla, se deriva a la chancadora durante 10 horas. Posteriormente pasa por la molienda para luego ser clasificado. Allí se adicionan los reactivos para la flotación y su análisis de malla. Producto de la flotación se obtiene el concentrado. El filtrado de los concentrados conlleva su envío a la molienda secundaria durante un período de seis horas. En este estado, la partícula de oro se encuentra limpia y en óptimas condiciones para la amalgamación y cianuración, donde el mercurio y la amalgama son exprimidos en una lona, destilándose, y se procede a la solución del oro, respectivamente. El método seguido es la agitación neumática, que suelta aire comprimido para la elevación del concentrado por el tubo elevador. Prosiguen los efectos de decantación, operación, control del cianuro y del alcali libre, precipitación, clarificación, limpieza y función de los precipitados. En el laboratorio se realiza el control de muestras del circuito de flotación, cianuración y de las barras, utilizando los métodos de soluciones de cianuro, ensayo de concentrados, minerales de mina, cabeza y relaves y ensayos de los precipitados. Finalmente, los cuadros de consumo de reactivos, mostrarán la eficacia del sistema y los resultados económicos de la planta de beneficio, como los costos, eficiencia de plata y mano de obra.

Jul 20, 1957

By D. Campbell Mackenzie

THIS paper is submitted primarily to put on record the results of a number of experiments carried out at the Wingdam mine of Consolidated Gold Alluvials of B.C., Ltd., with the object of establishing a reliable method of concentration of 'wash' and a maximum recovery of gold from the concentrate. It will be generally admitted that, during the last two decades, a tremendous amount of research work has been carried out, both by private companies and Government departments, with a view to improving the technique of the recovery of gold .from quartz veins or lodes. So thorough have been these investigations that milling practice at a modern quartz gold mine is almost an exact science, carried out with meticulous accuracy. In placer mining, on the other hand, very little departure from old traditional methods can be noted, with the exception perhaps of the more modern gold dredges. This may be due to the fact that the concentration of placer gravels, up to a certain point, is comparatively easy. Only a simple equipment of sluice box and riffies seems necessary where the gold is coarse and the gravel free from clay. In the early days of placer mining, when claims were rich and fairly 5hallow, nobody worried very much about fine gold; and, if clay was present, an enlarged dump box was constructed in which the gravel was subjected to a rather desultory puddling. That large quantities of gold are lost in normal placer practice is generally admitted. Some 26 years ago, I had inspectorial charge of many bucket dredges on the Ovens river, in Australia. Occasionally it was necessary for a dredge to work through its own tailing to reach a new section, and almost without exception enough gold was recovered from these tailings to defray the total cost of moving the dredge. Since those days, the technique of gold recovery in dredging has been considerably improved and it is still receiving close attention. Outside of dredge mining, most placer operations, deep or otherwise, are as they were-notorious gold losers, paying little attention to the recovery of fine gold and taking an absurd amount of time over each clean-up. In the Cariboo district of British Columbia, the alluvial gold is usual y associated with varying quantities of black sand (magnetic) and grey sand (non-magnetic); and it can be taken as axiomatic that, if you save all the black sand and grey sand, you save practically all the gold. It is on this hypothesis that we have carried out our research work and brought our recovery system up to its present highly satisfactory standard.

Jan 1, 1937

By A. R. House, G. W. Shepherd

Newmont USA Limited owns and operates the Phoenix Mine near Battle Mountain, Nevada, USA. The existing milling facility has operated since 2006 (House, 2010). Following the startup of the milling operation, and coupled with the upswing in the copper market, Newmont realized that Phoenix had no process option to treat transition and oxide copper ores. This meant that potentially revenue generating ore would be mined as waste. With no system in place to treat the transition and oxide copper, work began to determine the most feasible approach. After evaluating multiple options, the flow sheet was set for a runof- mine (ROM) heap leach pad and solvent extraction/ electrowinning plant (L-SX/EW). This paper will discuss the eight years of successes and challenges with developing the copper L-SX/EW plant and achieving commercial production of copper cathode.

Jan 1, 2014

By Christopher R. Lattanzi

"Discounted cash flow analysis provides a means of relating the magnitude of expected future cash profits to the magnitude of the initial cash investment required to purchase an asset or to develop it for commercial production. The objectives of discounted cash flow analysis are to determine:.. The net present value of a stream of expected future cash revenues and expenditures... The rate of return which the expected future cash flows will yield on a given level of initial cash investment.In the case of mineral properties, discounted cash flow analysis is generally accepted as the preferred method of valuation, whenever sufficient data are available to permit its reasoned application. Sufficient data are required to support estimation of all of the individual elements of cash revenue and cash expenditure which will be associated with the development and operation of the property, up to the end of its estimated life. It is the accuracy of these input estimates which determines the validity of the resulting determinations of profitability and rate of return on invested capital.In undertaking any discounted cash flow analysis, it is important to recognize certain fundamental attributes of the mining industty:.. The basis of any mineral development is the existence of an ore reserve... Costs are determined by the number of tonnes mined and processed, while revenues are determined by the number of pounds or ounces of metal produced. The two are related by the recovered grade of the ore... Profit is typically more sensitive to changes in revenue than it is to changes in cost... Commodity price is a principal determinant of revenue, but it is also the factor with which is associated the greatest level of financial risk.In the end, of all of the factors which must be considered in the discounted cash flow valuation of a mineral property, the most significant are the reliability of the reserve estimate, particularly with respect to recovered grade, the price at which the product is to be sold, and the risk of not maintaining the projected level of price."

Jan 1, 2003

By W. G. Davenport

Changes in copper extraction from 1960 till today are documented. The top ten changes have been: (a) replacement of reverberatory smelting by high intensity oxygen rich smelting (b) growth of the Outokumpu flash smelting to over 50% of the world's smelting capacity (c) successful development of single furnace coppermaking but only for low slag fall concentrates (d) replacement of the batch Peirce-Smith converter by continuous converting, but only in a few cases (e) increased SO2 capture throughout the industry, mainly-as sulfuric acid (f) development of low initiation temperature `big bight' Cs catalysts for treating the continuous high-SO2 strength gases from continuous smelting/converting (g) complete replacement of reverberatory anode scrap and cathode melting furnaces by the Asarco shaft furnace (h) adoption of stainless steel permanent cathodes and automated stripping technology for electrorefining and electrowinning (i) complete elimination of wire bar casting by continuous bar casting/rod rolling (j) development and adoption of extractants for turning weak impure leach solutions into strong pure electrolytes. It is postulated that the biggest possible change over the next 20 years would be complete replacement of smelting/converting by hydrometallurgical processing. However, this seems unlikely due to copper purity, precious metal recovery, and economic concerns. The increasing value of sulfuric acid to many copper companies gives chalcopyrite smelting/oxide-supergene leaching a nice synergy especially with the energy credits now coming from continuous smelters, and their acid plants.

Jan 1, 1999

By C. M. Bartley

Canada has been a producer of sulphur in various forms for about 100 years, Pyrites, as a source of sulphur dioxide for the manufacture of sulphuric acid, were being mined in the 1860's. Smelter gas, for the same purpose, has been recovered since 1928. Between 1935 and 1943, and from 1952 to the present, elemental sulphur has been produced in Canada from two raw material sources and by several methods. This paper attempts to present a view of the current status of the elemental sulphur industry in Canada based on the sour gas fields of Alberta and British Columbia. Production from this source has increased rapidly in the past 12 years to make Canada one of the major sulphur producers of the world. The present industry in Canada relies mainly on sour gas sulphur and it is expected that it will continue to grow in the future. However, before describing current activity relating to sour gas it may be of interest to outline briefly the early pyrite activities, the roots of the sulphur industry in Canada.

Jan 1, 1964

By G. H. Wigton

This paper, describing the concentrator practice of the Chief Consolidated Co., is one of a series being prepared by the United States Bureau of Mines. The concentrator adjoins the town of Eureka, Utah, in the Tintic mining district. The Chief Consolidated, Eureka Lilly, Plutus, and Grand Central mines, all of which are owned or controlled by the Chief Consolidated Mining Co., are the principal sources of milling ore. The ore is transported from mines to mill by railroad. Although all the mines are within 3 miles of the mill, the railroad distance varies from 1 mile to 12 miles.

Jan 1, 1930

By George H. Roseveare

Early flotation dealt primarily with the bulk concentration of sulphide minerals or the separation of one sulphide from another and was referred to as oil flotation because oils and fats were used as reagents. The separation or concentration of one nonmetallic mineral from another developed later with the use of fatty acids. Fatty acids are organic acids present usually as glycerides in tall oil and oils of fish, peanut, cottenseed, soya beans and ethers of veg¬etable and animal origin. Some, of these oils and their derivatives were used by the Phoenicians as early as 600 B.C. in making soap, and the use of such reagents in mineral dressing is referred to as "soap flotation". The first use of oleic acid for the recovery of minerals was the early agglomeration process.' The coarse particles of ore, from 1/16 to 1/4 inch diameter, were coated with large amounts of soap or oil and after screaming from the gangue were recovered by screening, hydraulic or table classification. In 1886, a patent was issued to Mrs. Carrie Everson in which the essential feature was the constituted commingling of pulverized ore, fat or an oil, either animal, mineral, or vegetable, for the purpose of effecting .a. union of the free metal or metallic portion of the ore with such admixed material whereby the same may be changed in subsequent separation of quartz or other rock therefrom by washing or other suitable means. The patent mentions the use of red, cotton seed, caster, sperm and linseed oils, In the early use of collectors the amount of oil for froth flotation was often 2 to 6 per cent by weight of the ore rather than pounds per ton.

Jan 1, 1959

By J. H. Daniel

Dust-related respiratory disease remains the major health concern in mining, and health agencies are proposing more stringent standards. The U.S. Bureau of Mines (USBM) is investigating techniques to continuously monitor respirable dust in real-time during the coal or ore extraction process. Continuous monitoring will allow mine operators to evaluate hazardous dust concentrations and adjust the operations to produce less dust. Mine instrumentation applications include machine-mounted and hand-held monitors, personal monitors, and area/environmental monitors. Six dust detection methods have been considered to meet application requirements. These are: light-scattering instruments, a smoke-particle detection technique, correlation of pressure drop across the collection filter with amount of dust deposited, the Tapered-Element Oscillating Microbalance (TEOM) instrument, a method that relates the amount of dust collected on a filter with the vibration of the filter, and beta attenuation measurement of dust. Studies to date have identified the TEOM instrument and the technique of correlating the amount of dust collected with the vibration ofthe filter as having the most promise for success. Development of the machine-mounted monitor is the highest research priority. The application options and progress to date in developing continuous monitoring instrumentation are presented.

Jan 1, 1995

By József Faitli, Barnabás Csoke, Károly Solymár, Zoltán Hatvani, Dimitri Papanastassiou

"Grinding has a significant economic impact on ore dressing/processing, therefore the sizing of mills has an outstanding role.In most cases, the sizing of dry or wet mills for ore processing is primarily based on the determination of the Bond grindability index, using the Bond-Kjos-Rowland relations. In several cases, grinding takes place under conditions different from these and the grinding conditions have a great influence on the post-grinding process. This is particularly true for the grinding of bauxites where grinding takes place in alkali, often in higher temperature (up to 100 ºC) in alkali Liquor. So it is necessary to develop a testing method providing a reliable grindability index even under these special circumstances (grinding in alkalis medium at different temperatures) and allowing a more precise mill sizing. The new heated mill is suitable to determine the grindability index under temperature-controlled circumstances, in liquids with different temperatures (water, alkali). This paper presents in detail the equipment, the conditions (parameters) of the testing process for wet and alkaline grinding, the measuring results and the conclusions."

Jan 1, 2003

By P. Leeuw, H. Mtegha

"The aim of this paper is to enhance the understanding of the nature of mining input technologies in the South African mining industry. In the context of this research, mining inputs refer to input technology into the activities in mining engineering fields, which include mining-related production activities, rock engineering, mine ventilation, and mine transportation (handling of personnel, material, broken rock, and pumping). Input technologies in supporting fields such as geology, other engineering disciplines, human resource, procurement, finance, as well as downstream fields that include metallurgy, and marketing of minerals, were disregarded.The mining input technologies were divided into 12 nodes, and data from a sample of 150 first-tier mining suppliers was analysed. It was found that, in general, there is a high local content in mining input technologies, particularly as regards technical support services, artefacts, and machine technologies. This points to the presence of mining-induced backward linkages in the South African mining industry. The majority (83%) of companies that provide input technologies into mining are located in Gauteng Province, and relatively few are found in provinces where mining is concentrated such as North-West, Limpopo, Mpumalanga, and Free State. IntroductionSouth Africa is well endowed with minerals, with more than fifty different minerals being mined throughout the country. For this and other reasons, mining is one of the crucial pillars in the South African economy and its importance is well documented (Robinson and von Below, 1990; Creamer, 2010; Department of Mineral Resources, 2015). In 2013, South Africa was the largest global producer of chromium, ferrochrome, platinum group metals (PGMs), and vermiculite and the second largest global producer of antimony, manganese, titanium, and vanadium (Chamber of Mines of South Africa, 2014). In 2013, the mining industry contributed 6.7% to South Africa’s GDP and was the fifth largest sector in the economy, as shown in Figure 1."

Jan 1, 2016

By Clifford S. Gibson

A year ago a paper (1) was presented at the Annual Western Meeting of the Institute regarding silicosis in Ontario mines. It described the whole problem as we see it and discussed the means of prevention. The work and aims of the Technical Silicosis Research Committee of the Ontario Mining Association, and of the Committee's field engineer, were fully described also and it is suggested that reference be made to this paper in order to have a better understanding of the observations which are presented now. These observations enlarge upon parts of the dust control measures already discussed and tell of general progress in the past year. They concern fifty properties, the majority of the operating mines, which vary in size from the hopeful prospect to established producers yielding 11,000 tons of ore daily. Most of these are gold mines; a few copper-nickel. The ores range from heavy sulphides to siliceous materials and they are mined by many methods from varying types of deposits. The majority of the latter are steeply dipping and all are found in Precambrian host-rocks. Up to the present, die greatest depth to which mining has penetrated is 6,400 feet.

Jan 1, 1939

By J. L. Eakin

A method was developed by the Bureau of Mines in the laboratory and in the field to relieve capillary waterblocks in gas wells. Impaired gas permeability was improved by this inexpensive chemical treatment which lowers the surface tension of the water held in the capillaries of the formation. Effectiveness of the alcohol-surfactant treatment was tested with a variety of chemicals and with sandstone cores cut from rocks having relatively low permeability. Field tests on 20 gas-producing and storage wells demonstrated the effectiveness and limitations of the method. The productive capacity of some wells was doubled by the treatment. The final test was evaluated by the neutron logging technique for measuring changes in apparent liquid saturation. Maximum apparent liquid saturation was reduced by 52 percent; gas production rate increased from 2.3 to 3.5 MMcfd (million cubic feet per day).

Jan 1, 1965

By Mary Ellen Large

This publication of Deep Foundations Institute (DFI) is intended to provide project owners, design engineers and construction professionals with guidelines for selecting cutoff wall and barrier systems and a general introduction to their methods of construction. Three categories of cutoff wall and barrier construction technology (excavated cutoff systems, in situ techniques, and driven cutoff systems) are presented and parameters for evaluating their design and construction are discussed. The information presented was compiled from the opinions of practicing engineers and construction specialists from the DFI Slurry Wall Committee.

Jan 1, 2021

By W. D. C. MacKenzie

IT IS almost exactly fifteen years since the discovery of the Leduc oil field and, as this luncheon is part of the Thirteenth Annual Technical Meeting of the Institute's Petroleum and Natural Gas Division, it seems, therefore, a singularly appropriate time to discuss the theme which the program committee has suggested for the occasion -the progress of the Canadian oil industry during the fifteen years since the discovery of the Leduc field. As you will see, I plan to take a few minor liberties with this suggested theme. I shall present ample evidence of growth and progress, but, at the same time, I want to refer to some areas where progress has been anything but conspicuous and to see what can be learned from these areas for the future. The achievements of the Canadian oil industry since the Leduc discovery in 1947 have been substantial, and the public is relatively familiar with the more spectacular developments.

Jan 1, 1962

By Iwueze Anaekperechi Rose

The International Labor Organization has declared mandatory adequate provision of safe workplace and safety for all workers in all occupations including the mining sector. Early scientists like Agricola (1559) who studied the health of Miners, found that there are peculiar health problems associated to their work and working environment. This unsafe working condition was one of the major factors that resulted to the Industrial revolution in England and eventually led to the establishment of regulations and laws guiding operations in all workplaces and workers in England and all over the world. Recent studies by Heinrich suggested chains of events of safety issues in the mining sector. Occupational injuries, accidents and ill health have huge social and economic implications on workers, their families and communities. Top mining top issues are respiratory diseases, noise, explosives, ventilation, fire, and explosion. However, one of the principal mechanisms for achieving Occupational Health and Safety (OHS) goals and mapping the future is government regulations of employers. In Nigeria, the situation is not different; mining operations are equally hazardous and have far reaching implications. In 1995 the Ministry for Solid Minerals was established to focus on the development of other categories of mineral products ranging from gold, coal, uranium, and tantalum deposited across the country. Prior to this an Act of Parliament Act Cap 121 of 1946, was in place to regulate amongst other contents mining safety. This was subsequently reviewed following the incidence of Lead poisoning resulting from small scale miners processing gold ore highly contaminated with lead in Zamfara state (northern Nigeria). Hundreds of children died as a result of exposure to lead poisoning, it was clear that the regulations were not sufficient (details to be discussed). However, advances have been achieved in mining engineering since then. A review team was constituted to provide a more stringent law to regulate mining operations in Nigeria. The strategies for mapping the future of OHS in mining engineering will employ amongst others setting and adopting ISO/ILO standards and enforcement; providing technical assistance; and establishing sustainable developmental structures as surveillance and compensation. The management systems approach was also developed as a result of cases of accidents. The accepted international standards guidelines and requirements will be proposed. Furthermore in mapping the future for Mining Engineering, it is suggested that most countries have their own management strategies and legislation to improve safety of workers through greater consistency and efficiency of OHS programs. Some American researchers came up with the Safety Engineering Model. The Australian Mining Council of mineral and petroleum resources after the Catastrophic Maura Disaster developed the National Mine and Safety Framework. In Canada, after the Hillcrest mine disaster in 1914, Allan shaft coal mine catastrophe in 1918, Westray mine explosion in 1992 and other disasters, Occupational Health and Safety Act R.R.O 1990 was sufficiently developed to provide adequate safety conditions and standards. In Nigeria after the disastrous Zamfara lead poisoning, which claimed the lives of hundreds of children due to exposure and lack of appropriate safety measures, stringent measures were developed by the federal ministry of Justice to address and regulate mining process in Nigeria.

Aug 1, 2013

By Thomas F. Anderson

(Measurements of stable isotopic variations (sulfur, carbon, and oxygen), supplemented by chemical, mineralogical, and petrographic analyses have been used to investigate the processes responsible for : (1) the incorporation of sulfur in coal, and (2) the (development of permineralized peat zones ("coal balls"). Sulfur isotopic results indicate that there are two principal sources of sulfur in the Pennsylvanian coals from the Illinois Basin: (1) "primary" sulfur assimilated by plants (low-sulfur coals), and (2) "secondary" sulfur produced by reactions involving H2S that was produced by the anaerobic reduction of sulfate in seawater which permeated the peat during post-depositional marine transgressions (the dominant source of sulfur in high-sulfur coals). Sulfur isotopic compositions of low-sulfur coals in Several Tertiary basins of Wyoming are consistent with a plant sulfur source. However, the inverse correlation between content and isotopic composition of sulfur observed in coals from the Powder River Basin suggest some "secondary" additions to these low-sulfur coals. Seveeral Quaternary (freshwater pears which were submerged by sea-Level rises during deglaciation over the past 30 ka have sulfur contents and isotopic compositions similar to high-sulfur coals. Carbon and oxygen isotopic compositions of calcareous coal balls from North America and Europe suggest that (1) the carbonate was derived from variable proportions of oxidized plant matter (typically predominant) and inorganic carbonate, and (2) the carbonate minerals were precipitated from fresh-to-brackish waters. Local geochemical and hydrological conditions were apparently more important than regional depositional environments in controlling the source of carbonate and the development of coal balls.

Jan 1, 1983