Search Documents

By T. W. Guy

During the past three years the Surface Preparation Committee of the American Mining Congress Coal Operators' Committees has been collecting data on dewatering and drying washed coal, and on screening coal in representative plants in the Eastern and Central bituminous fields. Because of wide variations in bed moisture, such data can be compared only after deducting the bed moisture. It was found that practically every company used a different routine for moisture sampling and determinations. Some reported the moistures as total moistures, others as surface moistures, air-dried moistures, or oven-dried moistures. For most of the reports it was necessary to estimate, from a consideration of the bed moisture and other data available in a given case, corrections to be made in order to obtain surface-moisture figures as a common basis for comparison. At any plant, and regardless of bed moisture, the percentage of surface moisture remaining in a product when the dewatering, or a given stage of the dewatering, has been completed, is the real measure of what has been accomplished. The descriptions and data given with Fig. 1 show that surface-moisture figures show relationships that would not be shown by total moistures. Therefore bed moisture should be deducted, or, if more practicable, the surface moisture of the products should be measured direct. A preparation engineer finds one per cent, or even a part of one per cent, of surface moisture a very important consideration in the results of his efforts to find the most effective and economical methods of reducing and controlling the surface moisture in his products within the required limits. Therefore it is important for him to have accurate measurements of surface moisture with minimum uncertainty as to whether they sometimes include less than the surface moisture and at others all of the surface moisture plus an unknown part of the bed moisture. The Problem We know that pieces of coal have a capacity for holding water: (1) inside themselves, which is a natural characteristic of the bed from

Jan 1, 1938

By A. Klingberg, M. Svensson, N. Smolko Schwarzmayr

"Removal of silicates and carbonates from sedimentary phosphate ores by the use of new synthetic collector/formulations was investigated in a comparative study with traditionally used collector systems as references. In the direct carbonate flotation the new formulations showed higher efficiency, contributed to an improved balance of P2O5 recovery and P2O5 enrichment in the recovered material. Efficiency of the new formulations containing synthetic surfactants was 1.5–2 times better than potassium salt of fatty acid sulfonate based formulations that are traditionally used for that purpose. The new formulations also provided up to 7% increase in P2O5 recovery at the same P2O5 grade. The new synthetic collectors for removal of silicates showed extremely good selectivity towards silica bearing minerals. The selectivity factor for the flotation tests when new formulations were used was 32–52 and for the flotation tests with the traditional collectors: 20–32. The ratio between distribution of an amount of silicates (as SiO2) and distribution of phosphate in the froth (waste) is defined as the selectivity factor. The new formulations provided more than 2% decrease of the amount of SiO2 at the same P2O5 recovery.INTRODUCTIONPopulation growth and decrease of arable land are the main reasons for constant increase of consumption of apatite (phosphate ore) in the fertilization field (Lannefors, Gorochovceva, Klingberg, Lima, & Gustafsson, 2015). Fertilizers play a key role for farmers to produce more with less land. The phosphate component of the fertilizer is vital for producing healthy and large amount of crop. As a result the demand for phosphate rock is growing.The largest producers of phosphate rock are the Unites States, Morocco, Tunisia, China, Russia, and Brazil. The term “phosphate ore” includes all phosphate-bearing minerals and rocks, but only two of them are of industrial interest: apatite (igneous origin) and sedimentary phosphate (Peres, Araujo, El-Shall, Zhang, & Abdel-Khalek, 2007). The majority of the world’s phosphate deposits are of the sedimentary type. There are two different types of sedimentary phosphates: siliceous and carbonaceous which are categorized based on gangue minerals (such as quartz, carbonates, mica, and clay)."

Jan 1, 2016

By T. W. Camm

"Search Amazon.com using the keyword “leadership,” and you are rewarded with a list of over 144,000 titles. There is no shortage of books and articles, many of them well written, with excellent ideas. So why is there still a constant cry for effective leadership in organizations? Often, the person in charge has personal blinders that prevent them from seeing or understanding how to implement the newest leadership idea or method. Either deliberately or subliminally, there is a disconnect from learning about leadership, and actually modelling and implementing what has been learned. Some current research in leadership theory can provide insight and tools to address this issue. INTRODUCTION Let’s start with a discussion of terms. Pseudo is defined by Webster (2015) as “Being apparently rather actually as stated.” Synonyms include affected, assumed, contrived, fake, false, phony, pretended, and artificial. Antonyms for pseudo provide additional clarity, especially when we consider terms normally associated with effective leadership: genuine, natural, unaffected, unforced. A similar type from my world of academia is a pseudointellectual, “A person exhibiting intellectual pretentions that have no basis in sound scholarship” (Dictionary.com, 2015). This is a person pretending to have an interest in intellectual activities for status; a fraudulent intellectuality. The thought of applying the term pseudo to leadership first occurred to me while reading Power and Innocence by Rollo May (1972). In discussing the dynamics of power, and how the innocent are often victims of the exercise of power, especially the more aggressive and destructive types of power, he saw two types of innocence. The first he called authentic innocence, which he described as a childlike clarity that carried into adulthood. The second type he called pseudoinnocence, a type of naïveté that makes a virtue of powerlessness, weakness, and helplessness; being more childish than childlike (p. 48-50). Just as there is the potential for pseudoinnocence and pseudointellectuals, it is also possible to experience pseudo leadership. (I hope the gentle reader is not troubled by my decision to use pseudo leadership as two separate words, in contrast to the use of compound words for pseudoinnocence and pseudointellectual cited above. Since there is no official definition of pseudo leadership, I have exercised my author’s prerogative to treat it as two words, both because I think in this particular application this makes the most sense, and also I think it is easier to read). As we will see, there are numerous theories applied to leadership. What is so troubling to many of us in organizations, there are a myriad of “leaders” in companies espousing pet theories, but very few instances where the actions of these individuals match their words. This is a particularly important problem when we look at the effect this has on the day to day operations of a mine, and where effective leadership (or its absence) can have a profound impact on both productivity and safety."

Jan 1, 2016

By Youngkook Lee

The precipitation kinetics of NbC in ferrite matrix of the Nb microalloyed steel was investigated experimentally and numerically. The mole fractions of NbC precipitates formed at different isothermal temperatures were measured as a function of holding time by electrical resistivity test and were compared with both a mathematical model based on time-dependent nucleation and growth rates and the hardness. There is a good match among the calculated and measured precipitation kinetics of NbC and the hardness. The isothermal precipitation-temperature-time diagram of NbC in ferrite matrix of the Nb microalloyed steel was newly generated. Keywords: Precipitation, Carbide, Ferrite, Nucleation, Growth, etc

Jan 1, 2003

By Jorge Armstrong, Sean Warren, JOSEF BOURGEOIS

The application of statistical analysis software programs has proven useful for the investigation of rockfall runout distance along a designed slope. Rockfall modeling programs are continually being upgraded with more sophisticated analysis tools, such as the use of the rigid body versus lump mass models. Engineers at mine sites utilizing the software may have varied experience related to these models, their associated input parameters, and how to interpret the generated results. To address this concern, researchers at the Spokane Mining Research Division (SMRD) of the US National Institute for Occupational Safety and Health (NIOSH) investigated the influence of slope height, slope angle, slope material, and rock size for both rigid body and lump mass models in a 2-D statistical analysis program. Based on a literature search and industry input, specific ranges common to that of an open pit mining environment were chosen for each of the input parameters to determine 90% rock runout distance as well as their sensitivity to change. Data collected from this numerical analysis and simulation will be compared to empirical rockfall data gathered through the duration of the Highwall Safety project conducted by NIOSH from 2022–2026.

Jun 18, 2023

By J. Armstrong, J. Bourgeois, S. Warren

The application of statistical analysis software programs has proven useful for investigation of rockfall runout distance along a designed slope. Rockfall modeling programs are continually being upgraded with more sophisticated analysis tools, such as the use of the rigid body versus lump mass models. Engineers at mine sites utilizing the software may have varied experience related to these models, their associated input parameters, and how to interpret the generated results. To address this concern, researchers at the Spokane Mining Research Division (SMRD) of the U.S. National Institute for Occupational Safety and Health (NIOSH) investigated the influence of slope height, slope angle, slope material, and rock size for both rigid body and lump mass models in a 2-D statistical analysis program. Based on a literature search and industry input, specific ranges common to that of an open pit mining environment were chosen for each of the input parameters to determine 90% rock runout distance as well as their sensitivity to change. Data collected from this numerical analysis and simulation will be compared to empirical rockfall data gathered through the duration of the Highwall Safety project conducted by NIOSH from 2022–2026.

Mar 2, 2022

By Z. Q. Yue

Many large rock avalanches and/or landslides have occurred in mountainous regions around the world. Their occurrences are normally rapid and unexpected, which can cause disasters. They have been investigated extensively by many researchers and engineers since the 1903 Frank Slide on Turtle Mountain, Alberta, Canada. They are one of the most peculiar phenomena because the rock debris of more than one million m3 can move over the horizontal distances exceeding those expected from conventional friction physics. This paper presents a gas cause hypothesis responsible for the large rock avalanches. It is the migration and expansion of a certain amount of highly pressurized and dense natural gas mass from deep geological grounds into the mountainous rock mass slopes. The natural gas with high pressure and density can escape from the deep geological ground and flow through faults, weak zones and/or porous channels into the rock mass forming a mountainous slope. The rock mass forming the slope has the high tensile and compressive strength and can resist the initial loading of the gas mass migrated into and stored in their voids, pores, holes, gaps, openings, apertures and cavities. With time, more and more gas mass from deep ground can migrate into and stored in the slope rock mass. Eventually, the peak equilibrium of forces and deformation reaches. The expanding power of the gas in the slope rock mass would instantly and rapidly break, erupt and/or explode them. The compressed and dense gas mass would mix, flow and expand together with the broken rock debris mass and continue offering their remaining expanding powers to the moving and sliding debris mass. As a result, the rock debris of large volume can reach the runout distances exceeding those expected from the conventional friction physics. The gas would escape into the sky and the solid rock debris would remain on the ground spreading over large ground area. The 1903 Frank Slide is examined to show this gas cause and mechanism in mountainous regions.

Jan 1, 2015

By A R. Penney

Safety management, both personal and that associated with catastrophic hazard, helps to define the success of mining companies. Personal safety management, often categorised by slips, trips and falls, has been widely addressed, with numerous approaches successfully adopted. Catastrophic hazard can lead to a single accident (eg ground collapse, underground fires etc) causing multiple fatalities. Catastrophic hazard management in mining is an emerging discipline, and as such there are various pitfalls to demonstrate its effectiveness and success; it is much more than simply meeting regulatory requirements. Various standards, guidelines, and leading practices are available for reporting key performance indicators. While measuring and reporting safety related key performance indicators (KPIs) such as Total Recordable Injury Frequency Rate (TRIFR), Lost Time Injury Frequency Rate (LTIFR), are important, they often lack detail, and give little insight into the effectiveness of catastrophic hazard management strategies and controls. Catastrophic hazards are low likelihood, high consequence events, and as such demand a different management approach. Companies cannot use the suite of personal safety metrics to help demonstrate management of catastrophic hazards. In-field verifications have revealed that senior management commitment to safety is often clear, well organised, and resourced. However, there are often some inconsistencies between what management promotes and plan, to what the operational teams understand and implement. Communication and clear understanding of expectations were the common themes identified to help empower supervisors to reinforce requirements of catastrophic hazard management. A lack of specific, measurable, and time-sensitive goals and objectives for the short- or medium-term, making it challenging to track progress was another key observation. Development of an integrated, multi-disciplinary auditing process executed by an experienced team of technical subject matter experts, provided an in-depth understanding of the requirements of catastrophic hazard management. Areas such as underground fire prevention, explosive storage, electrical safety, mobile vehicle interactions, ground control, inrush, and shafts and winders management have substantial overlap and intertwined processes, and similar strategies for emergency responses. Auditing of catastrophic hazards and safety management systems compliance is only the first step in safety assurance. Completing operational performance audits in technical areas and benchmarking the site verification of safety management documents and verifications forms a critical part to clearly demonstrate industry leading safety practices. No longer is it the external inspection or regular hazard management plan review requirements that dominate, but rather the culture of continual hazard identification, management, controls verification, underpinned by improvement and follow-up verifications of the corrective actions.

Mar 29, 2023

By Giuseppe Bonifazi

Minerographic and petrochemical research was carried out on crude ore samples from the complex polymetallic Zn-Cu-Pb sulfide ores of , Sotiel in Huelva province west of Seville, Spain. A computerized image analysis system was used to define the structural and textural characteristics of the ore to obtain information on the degree of liberation of the different minerals (i.e. pyrite, sphalerite, galena, chalcopyrite). Techniques of digital multispectral image processing of reflected light microscopy images were used. Particular structures were identified by means of mineral associations and numerically quantified to obtain useful information for designing beneficiation processes.

Jan 1, 1991

More and more coal in Australia is extracted by underground mining methods especially by longwall mining. These methods can be particularly sensitive to relatively small-scale structural discontinuities and variations in roof and floor rock character. Traditionally, information on these features has been obtained through drilling. However, this is an expensive process and its relevance is limited to the immediate neighbourhood of the boreholes. The geological uncertainty remains. Seismic surveying, especially by 3D seismic, is an alternative tool for geological structure delineation with growing credibility. In fact, it is one of the most effective geophysical methods available for identification of geological structures such as faults, folds, washouts, seam splits and thickness changes which are normally associated with potential mining hazards. Seismic data even can be used for stratigraphic identification. The information extracted from seismic data then can be integrated into mine planning and design. In this paper, we demonstrate computer aided interpretation techniques for maximising the information from seismic data and illustrate the ability of seismic reflection methods to resolve localised geological features. Both synthetic and real seismic data obtained in recent 2D and 3D seismic surveys from Australian coal mines will be used. Compared with results obtained with drilling programs, the structural definitions from seismic are of unprecedented quality.

Jan 1, 2002

By F. Djahanguiri

The U.S. Bureau of Mines is conducting research on underground stope leaching of metalliferous ores to minimize the environmental impact of ore processing on the surface and to maximize minable reserves. An aspect of this research is to minimize pregnant solution losses and/or groundwater contamination by leach solutions. Bulkhead design and construction are important issues for solution control and stope leaching economics. A reinforced concrete bulkhead was designed, constructed, and tested for solution control in an underground mine near Idaho Springs, CO. This paper presents the bulkhead design methodology and construction procedure.

Jan 1, 1995

By Jr. Foot

EIMCO Process Equipment Company has introduced the new SmartCell series of conventional flotation cells. The flagship of this new development is the 5000 ft3 cell that is the largest available in industry. This new series of cells includes a cylindrical tank design, a conical draft tube and froth crowder. Optional air control, wash water addition and embedded expert control are available. A discussion of the design parameters, energy efficiency, testing, and commercial plant results are presented.

Jan 1, 1997

By Evgenii Pavlov, Ivan Tronin, Viktor Timofeev, Vladimir Kislov, Sergei Bogovalov

"Modeling of the magnetohydrodynamical (MHD) and thermodynamical processes during the industrial scale Direct Chill (DC) casting of aluminum slabs is performed using a combination of ANSYS/CFX and ANSYS/EMAG software. The electromagnetic field is modeled through ANSYS/EMAG, while hydrodynamic and thermodynamic processes are modeled through ANSYS/CFX. Both packages were modified in order to calculate MHD flows in the liquid pool that forms during aluminum DC casting, and they were unified into a software combination that provides simultaneous simulation of all the above processes. The simulation shows that the electromagnetic stirring of the molten aluminum changes the shape of the solidification front (solid-liquid interface) very dramatically, namely it becomes significantly flatter. This effect should improve the internal structure of aluminum DC slabs and allows us to increase the casting velocity.IntroductionProduction of Aluminum alloys with high mechanical properties and structural uniformity is one of the main goals of industry. The preferred production method of aluminum alloys in most modern plants is Direct Chill (hereafter DC) casting because it offers high productivity and commercial success. One important limitation of this technology is the development of centerline shrinkage in slabs larger than about 1 meter. The improvement of the internal structure of long DC cast slabs can be achieved by electromagnetic stirring (hereafter ES) of the liquid metal above the solidification front. This intensifies heat transport in the zone close to the solidification front and suppresses shrinkage formation."

Jan 1, 2013

By M. Fafard, D. Picard, J. -F. Bilodeau, G. Soucy

To simulate adequately the behaviour of a Hall-Heroult electrolysis cell, a finite element model must take into account the properties of each material. However, it has some lacking knowledge on the mechanical behaviour of materials, like the long-term visco-elastic (creep/relaxation) behaviour of cathode. A three-dimensional model is then proposed in this paper and will be ready to be implemented in the finite element code FESh++. The model was developed using the three-dimensional model based on thermodynamic of irreversible processes where the choice of the internal variables is based on a phenomenological approach. All parameters of the model are represented by constant constitutive tensors and the temperature and chemical dependencies are taking into account through scalar functions multiplying the constant constitutive tensor. The goal of the first part of this project was to determine the parameters of the threedimensional visco-elastic model at the reference state (virgin material at ambient temperature) of three different cathode materials. This paper presents the theoretical model and the results of creep tests at ambient temperature for the semi-graphitic carbon cathode.

Jan 1, 2006

By T. Shumka, M. J. Druckenmiller

"INTRODUCTION As we push further into the 21st century and closer to a more efficient mine, safety and operational enhancements are the two major keys towards attaining success. The Crusher Vision Automation System (CVAS) is a technological advance that will allow an operator to achieve higher safety and higher operational goals in the same piece of equipment. The CVAS is a patent pending system and method for measuring and maintaining the closed side setting (CSS) on gyratory crushers. In the same equipment and technology package, the CVAS will also allow safer placement of main shaft pieces for maintenance and replacement. This technology yields multiple uses and allows a site to significantly enhance safety and operational efficiencies. This measurement technique is used to provide more accurate data and faster data collection times than current techniques used today. It will give crusher operators accurate and reliable measurement for the CSS in a live, operating environment. Measurement data can be collected in five minutes allowing for fast adjustment of the mantle position and subsequent enhancement and streamlining of a crusher and downstream flowsheet. The advantage of this system is that it is permanently mounted at the crusher location, where the operator can turn the system on and off as many times as they like throughout the day with a goal of maintaining a constant CSS gap based on production and maintenance criteria to help streamline operations and enhance safety efficiencies.Regarding its other main functional area, mainshaft maintenance, it allows this work to be performed remotely while keeping personnel safer and out of harm’s way. SAFETY ENHANCEMENT The safety factor enhancement with this system is extreme. It does not require the use of overhead cranes, cleaning out the crusher, lowering people into the crusher or having the operator lower paint cans or lead balls into the crusher pocket while the crusher is in operation for measuring the setting. In order to perform the CSS measurements, the operator only needs to operate the laser through manipulation of a joystick while watching the video feed. Danger of a person falling into the crusher while trying to take measures is eliminated, as are the effects of handling lead balls and tracer dyes."

Jan 1, 2015

By G. Bezuidenhout, N. C. Steenkamp

Buying centres are the first point of contact that determines whether ore will be considered as having sufficient provenance to be considered ethically sourced. The information that needs to be captured on the blockchain platform ranges from reports on in-loco inspections and audits of mining and purchase sites. This will guide passive and active monitoring of mining activities, trade-offs for identification systems, including biometrics for the registration of artisanal sellers, scrutiny on the selection of security measures and companies for buyer centres and stockpiling warehouses, evaluation of active and passive infrastructure security, and remote monitoring applications. Assistance with selection and training in geochemical testing instruments to determine the grade of ore material or concentrates and sorting, on-the-ground investigations, guidance on monitoring methods from stockpile and packing area along the transport route to the final destination are required.

Jan 1, 2023

By Circe Verba, Scott Montross, Jon Yang

This work is a first-order study to assess the suitability of an organic acid lixiviant to extract rare earth elements (REE) from coal preparation fines refuse sourced from a Pennsylvania mine with a total REE of ~ 300 ppm. The extraction of REE using an organic acid, in this case 0.1Mcitric acid and 0.5Mtrisodium citrate solution, is compared against 0.5M(NH4)2SO4, 1MHCl, 1.2MH2SO4, and 0.5Methylenediaminetetraacetic acid (EDTA). Ashing the coal waste material prior to leaching tests with the citrate solution nominally improved REE extraction. Buffered citrate solution recovered 7% of the total REE in the as-received Isabella Fines as compared to 11% in ashed samples, whereas (NH4)2SO4 extracted 5–6%, respectively. EDTA recovered up to 33%of the total REE, most likely due to the higher coordination chelate bond. Mineral acids, however, outperformed the organic acids on ashed material (16–52%REE recovery), suggesting that organic acids may not be a suitable competitive option for REE extraction from these types of feedstocks.

Jun 15, 2021

By P. James

"INTRODUCTION Control of target stream acidity is widely used in MIW (mining influenced water). Tailoring pH (a measure of acidity) finds application for controlling key chemistry in both process and waste streams. Traditional lime addition for neutralization and precipitation is most often used but has high reagent costs and results in large amounts of mixed metal sludge requiring costly disposal. A new adaptation of BPS’s patented DEMET™ technology (Dynamic Electrolytic Metal Effluent Treatment) platform offers a potentially improved and “reagentless” alternative to traditional chemical addition for pH adjustment. Electricity rather than chemical addition utilized in BPS’s proprietary approach controllably tailors target stream pH. The method offers a simple, low-cost processing technique yielding cleaner treatment chemistry. BPS’s “green” approach may yield lower operating (OPEX) and life cycle costs and significant reductions (up to 50%) in sludge generation compared to conventional lime treatment. It can also allow new opportunities to generate revenue via selective recovery of valuable processing byproducts. Specific savings and revenues depend on the target site chemistries, details, and processing goals. A more detailed discussion of the process and its operational principles may be found in Reference One.[1] Here application of the BPS treatment to POx (Pressure Oxidation) leaching as an alternative to traditional chemical addition is examined. An example operation process flow for gold mining is considered.[2] Promising processing points for potentially replacing conventional processes with DEMET are noted. The possibilities for lowering OPEX costs, lessening sludge creation, and capturing various valuable byproducts and residuals are examined. Financial life cycle benefit estimates of the principal gains provided by DEMET application to the example operation are noted. Extension and generalization of the analyses to a wider range of scenarios is explored."

Jan 1, 2016

By C. O. Swanson

Introduction It is thirty-odd years since I first entered the mining field by working underground at Anyox, which makes 1t clear that I can qualify as one of the older generation and claim the privilege of dealing in generalities and broad impressions. In this position I find it interesting to re~ view the salient changes that have taken place during the past quarter-century and indulge in some speculations concerning the future, with the hope that my comments may be of value to others engaged in the field of mining geology. As indicated by the title, the treatment is a perspective from a single viewpoint rather than an attempt to give a complete and impartial analysis. This plan, while deficient in some respects, has the advantage of being more specific than one based on .a. compilation of opinions. An additional advantage is brevity, which would be difficult to obtain on a subject of this scope if it were viewed from all angles. In conformity with the general plan, specific references to the literature have been avoided as much as possible, although a number of publications of general nature are listed at the end of the paper. This procedure is intended to give credit to the sources used without making them in any way responsible for the interpretation. The starting point for the discussion is the situation as it existed twenty-five years ago, when, as a recent graduate, I first had a fairly complete picture of it. However there is one impression of an earlier; stage that seems worth mentioning. In one of my first courses in geology the statement was made that some of the leading authorities of the previous generation, who guided geological thought at about the beginning of the century, were inclined to question the value of an association with mining. This attitude was no doubt exceptional, and certainly it was not adopted by the students who laid the groundwork for mining geology in North America. But its existence even in a limited circle is significant m showing how far the application of geology has advanced as the result of the investigations started during the first part of this century.

Jan 1, 1949

By J. Mastoris

The problem of defining the optimum final limits of an open pit mine has challenged the mining industry for the last three decades, mainly due to the great number of variables involved and the sheer computational effort required in real life applications. An actual lignite deposit is used in this study in order to introduce and apply a methodology to be used as a basis for surface mine design optimization. A geologic reserves model of the deposit is first developed with the use of an integrated geostatistical modeling package. The model is transformed into an economic one through the use of flexible objective function formulation(s). The optimization of the final open pit limits is then enabled with the use of a competent, commercial optimizer, and comparative sensitivity analyses are performed in order to study the effect of some basic mining and economic parameters on the optimal pit design. The conclusions drawn can develop useful guidelines for decision making by the mine operator.

Jan 1, 1995