Search Documents

The following methods should be used to protect miners from the adverse health effects of exposure to respirable coal mine dust and respirable crystalline silica: ? Informing workers about hazards ? Establishing written emergency procedures ? Using engineering controls, work practices, and personal protective equipment (including respiratory protection when dust control equipment is being installed, maintained, or repaired) ? Monitoring exposures ? Conducting medical screening and surveillance ? Encouraging smoking cessation ? Maintaining medical records

Jan 1, 1997

By S. Kline

The compositions of metamorphic minerals of the south limb of the Dore Lake Complex have been determined by microprobe techniques. Mineral assemblages typical of the greenschist facies occur in Mg-rich bulk compositions, but in Fe-rich rocks albite-epidote amphiboli te facies assemblages occur. Low oxygen fugaci ties and a general paucity of metamorphic fluids prevailed in most of the complex, but a higher oxygen fugacity is indicated near the Chibougamau Pluton, and a local abundance of C0z and Cl in fluids near the pluton is suggested by the presence of scapoli te. The metamorphic gradient overprinted on the complex near the Grenville Front is apparent in mineral chemistries as well as by the appearance of garnet. Chlorite becomes richer in Mg, and iron is fractionated more strongly into hornblende. The amphibole also increases in Alz03.

Jan 1, 1984

By Mark Laffoon

Gold Fields Operating Co.-Chimney Creek has conducted numerous ore reserve modeling studies In order to optimize the estimates of the gold grades and tonnage distributions. Improved models continue to be produced for the major pits which Increase confidence levels required by Gold Fields management and provide the basis for more accurate long and intermediate term mine planning. Various kriging and non-kriging estimation techniques are used at Gold Fields -Chimney Creek Mine. This paper reviews the modeling histories and, current procedures used to construct these models with particular emphasis on the North Pit deposit.

Jan 1, 1991

By Ossi V. I. Hintikka

There are several limestone deposits around the Lohja area in southern Finland. Raw material for cement rock is mined from some of them. The formations are geologically complicated, and therefore selective mining is used whenever possible. One of these mines is the Tytyri underground limestone mine, which is divided into two parts; Törmä and Solhem. In addition to the selective mining system hand sorting or picking must be used at the Tytyri mine to improve the overall grade of the blended limestone. Some means were needed in order to improve the quality and to increase the feed rate by the elimination of hand sorting. Sorting machines were considered and eventually a Sortex 811MW was pilot plant tested at the Ojamo mine near Tytyri. This machine now continues to be used on production.

Jan 1, 1971

By S. Oglesby, A. L. Thomas

Until recently, probably the best means of sampling airborne dusts has been the impinger method. Dust-laden air is drawn into a sampling tube, and the particulate matters separated from the air and collected in the liquid in the impinger. A sample of the suspension is prepared on a slide and counted through a projection microscope. This method is simple and reliable, but it does suffer drawbacks. Since the collected particles must be counted visually, results of the dust count are not immediately available at the time the sample is taken. This seriously impedes studying the effectiveness of dust inhibitors, such as water sprays, or making adjustments in equipment. Greatest disadvantage of all, however, is the tedious task of counting particles in the sample. With the growing desirability of taking more samples, the effort involved in making these counts is a real factor in the cost of dust control. Finally, it is generally recognized that impinger dust counts can be related to health hazard only for specific kinds of dust and under similar conditions. This is because the rather complex mechanism of dust damage depends so much on size distribution of the dust. Counts determined by impinger samples cover a limited size range that does not necessarily corre-

Jan 1, 1960

By Yiling Zhang, Paul A. Salvador, Gregory S. Rohrer

"Photocatalysis utilizes solar energy to produce hydrogen by splitting H2O. When a thin film of photocatalyst TiO2 is supported on a ferroelectric BiFeO3 substrate (band gap ~2.5 eV), the TiO2/BiFeO3 heterostructure is capable of photochemically reducing Ag+ to Ag0 in aqueous solutions under blue light with enhanced efficiency. The observation of spatially selective silver patterns on surface of the heterostructure after reaction suggests that photogenerated electrons and holes in ferroelectric BiFeO3 are driven in opposite directions to reduce their chance of recombination. Comparisons of the amounts of reduced silver on TiO2 film grains with distinct phases/orientations show that the reactivity is mildly preferential on anatase TiO2 phase and does not strongly depend on crystallographic orientation of BiFeO3.IntroductionTitania (TiO2) is capable of photocatalytically converting H2O to hydrogen and oxygen under the irradiation of ultraviolet light. [1, 2] One of the limiting factors for titania to be used as an effective photocatalyst is its band gap. Because the absorption edges of rutile and anatase titania are at 3.0 eV and 3.2 eV, respectively, they can only absorb light in the UV portion of the spectrum, which is about 3% of the available solar energy. [3-5] This limitation has motivated attempts to modify the absorption edge of titania so that it can absorb visible light.One strategy is to substitute a portion of the titanium and/or the oxygen with other atoms. There are numerous reports on visible light absorption of titania by doping and co-doping of Cr, V, Mo, Sb, Fe, N, S, C, and F. [6-34] Another strategy is to add an adsorbed molecular species that absorb visible light and donate an electron or hole to the titania, such as organic dyes [33, 35, 36] and Ce3+/Ce4+. [37, 38]The strategy in the present work takes the approach of depositing a pure titania thin film on a visible light absorbing substrate BiFeO3 to induce visible light activity of the heterostructure. BiFeO3 is a semiconductor with a band gap of about 2.5 eV [39-41] and is photocatalytically active in visible light. [42, 43] It is also ferroelectric with spontaneous polarization along pseudo-cubic <111> directions of 6.1 µC cm-2. [44] The spontaneous polarization gives rise to internal electric fields that drive photogenerated charge carriers, namely electrons and holes, in opposite directions to reduce their chance of recombination. [45-47] Additionally, the separation of electrons and holes leads to the spatial separation of reduction and oxidation half reactions so that the back reaction of intermediates is also suppressed. Such charge carrier separation has been reported in TiO2/BaTiO3 heterostructures with UV light illumination. [48-51] The TiO2/BiFeO3 heterostructures in this work combine both advantages of the relatively narrow band gap and the internal fields in BiFeO3 to enhance the overall photocatalytic activity."

Jan 1, 2014

By Kenneth D. Winters

This Bureau of Mines report presents a Fortran IV computer program for the structural analysis of (1) protective canopies used in underground mines to protect equipment operators from roof falls and (2) rollover protective structures (ROPS) used in surface mines to protect equipment operators during vehicle overturn accidents. The program, entitled PLASTIC CANOPY, permits rapid and inexpensive calculation of the ultimate strength and deformation characteristics of a canopy for a variety of static loading conditions. The structure is modeled as a series of interconnected beam and/or plate elements. Stresses in, and displacements of, each structural element are computed and printed out at the yield strength of the canopy, at several intermediate load levels between the yield and ultimate strength of the canopy, and at the ultimate strength of the canopy. Other features of the program include prediction of buckling of a beam member under combined axial compression loading and bending, plotting of the input geometry of the structure, and plotting of the deformed shape of the loaded structure. Program description, input instructions, program listing, and four example problems are included.

Jan 1, 1979

By Christoph Mueller

Mining operations today are characterized by a high degree of mechanization and single machine automation. However, their potential for cost cuttings and increase of productivity in the future is quite limited. Enabled by newest IT and networking technology, the operation of underground mines more and more can be seen from a process related point of view: Standardized Ethernet and Wireless LAN are the basis for a seamless and unified communication backbones providing an integrated infrastructure for data, telephony and video. All the components are available as off-the-shelf devices leading to an excellent cost efficiency. Basing on this standardized infrastructure, the equipment is able to become part of the infrastructure. To enable machines to be integrated smoothly into IT networks, the machine also has to have enhanced networking capabilities. This results in a new system architecture for the on board machine electronics separating real time control from IT and networking level functionality which can be implemented by a Machine Server. This machine server communicates with all kinds of above ground systems using mainly standardized formats like html or the IREDES standard. This information is made available mainly in 3D mine visualization tools. The paper explains this technology and shows implementations by two working examples.

May 1, 2006

By José Roberto de Olveira, Anna Paula Littig Berger, Caio Vaccari Silva, Victor Bridi Telles, Felipe Fardin Grillo, José Roberto de Oliveira

No presente trabalho foi proposto uma análise da eficiência de desfosforação de uma mistura padrão M1 e outras cinco misturas, onde foi realizada variação da massa de mistura adicionada ao sistema (60,70 e 80g), temperatura de trabalho (1350ºC e 1350ºC ajustada) e metodologia de adição. Os testes experimentais foram realizados a uma temperatura de 1400°C, com agitação de 450 RPM, em um forno de resistência. Para a análise das propriedades da escória, foram realizadas simulações através do software de termodinâmica computacional FactSage 7.2 e análises de imagens obtidas da superfície do cadinho ao final dos experimentos no software Quantikov. A mistura M1 apresentou melhor desempenho do que as misturas em todas as situações estudadas, sendo observado que melhores condições experimentais foram a utilização de 70g de mistura, a uma temperatura de 1400ºC, com a metodologia padrão de adição de toda a massa da mistura no início do experimento.

Oct 1, 2019

By J. M. GARZA

The production of oil in Mexico during 1945 was 43,402,852 bbl., or a daily average of 118,912 bbl. In March 1938 most of the oil properties were taken over by the Mexican Government and since then have been operated by Petroleos Mexicanos, an agency of the Government. The variations in the production during the last 8 years have been due to- fluctuations in the export market demand for Mexican oil rather than to the productive capacity of the fields. Since 1937, yearly production, to the nearest hundred thousand barrels, has been as follows :

Jan 1, 1946

By Nicole E. Evanek, Anthony T. Iannacchione

"Over the past 36 years, a great deal of information has been presented and discussed at the International Conference on Ground Control in Mining (ICGCM). The topic of surface subsidence engineering has resonated throughout each of the 36 conferences, producing 155 related papers. These papers have come from many countries. The major focus has been underground coal, especially longwall mining, but hard rock mining has also received attention. This impressive collection of reports presents a unique opportunity to reflect on the progress made towards understanding subsidence basin characteristics and developing methods to predict and mitigate its impact.In the initial meetings, the focus was on measuring subsidence and developing prediction methods. As understanding increased, predictive methods were developed and tested, especially in North America, China, Australia, Europe, and India. Efforts were made to understand how structures, aquifers, and surface waters were impacted by the formation of subsidence basins. As time progressed, the number of papers dropped slightly and became more focused on site-specific conditions. Most recently, advanced monitoring techniques have revealed new information, spurring a resurgence in research activity. Another recent focus has been on anomalous horizontal deformations occurring in sites with significant relief. Several reports from Australia and one from the US have brought this issue to light. In closing, all of these surface subsidence engineering papers have chronicled the maturing of this most important topic and, in the process, highlighted the importance of the ICGCM in the evolution of our current state of practice.INTRODUCTIONThe aim of this paper is to examine the role of ICGCM in 1) shaping our understanding of the mining induced subsidence phenomena, 2) developing tools to help predict its impact on the surface, and 3) evaluating controls to mitigate these impacts.This analysis involved the consideration of 155 papers available within the ICGCM conference proceedings and listed under the subsidence topic. Three of the papers where only available as abstracts and were not included in this analysis. Four other reports were focused on topics other than underground coal mining-induced subsidence issues and were also not included. It should also be noted that papers dealing with overburden behavior were not included in this analysis. As a result, 148 papers were reviewed and analyzed (Figure 1)."

Jan 1, 2018

By Y. Serres

In the past, conventional reflection seismic techniques were not very successful when applied to typical mining exploration: they lacked resolution in the shallow range or were not cost effective. By combining a light earth tamper source, special geophones and field procedures, a stacking process of the returning seismic events using a microprocessor system, and a sophisticated sequence of adapted digital data processing, Mini-Sosie achieves high resolution in the 100-ft to 4000-ft range. Additional advantages result from the very quiet nature of the source and flexibility of the system. Although Mini-Sosie might be used in the refraction mode, or for well velocity logging, it has found its main applications with the reflection technique.

Jan 1, 1978

By Diogo Fonseca, José Manuel, Nuno Fernandes, Blessing Taiwo

This research focuses on enhancing the synergy between blasting and primary crushing operations in quarries. A blast operation at dstgroup aggregate quarry in northern Portugal was simulated to fine-tune blasting techniques aimed at optimizing fragmentation indicators. The methodology involves conducting precise blast drill hole surveys, generating detailed terrain 3D models, and integrating these models into blast simulation software to enhance accuracy and optimize production efficiency. The study applies these simulations to test blasts, evaluating improvements in cost-effectiveness, crusher power consumption, and fragmentation efficiency using both aerial and terrestrial image analysis technology. The quarry key performance indicators (KPIs) guide the blast design simulations, ensuring practicality and relevance. The case study blast revealed that implementing optimum blasting techniques can enhance crusher throughput, reduce operational costs, and improve safety. This paper is part one of a three-part technical series where we aim to create a sampling procedure and establish a reliable baseline for the current state of operation. This baseline will be used in subsequent follow-up technical papers to make recommendations and improvements. The outcome of this study provides a framework for quarry operations seeking to enhance their efficiency.

Jan 21, 2025

By M J. Schultz, R L. Rude, D M. Tomko

The US Mine Safety and Health Administration (MSHA) conducted compliance assistance diesel particulate matter (DPM) sampling throughout the underground metal and non-metal mining industry. Based on that sampling, MSHA identified mines that were having difficulty meeting the DPM limit. To provide further assistance, MSHA then visited approximately 60 of the mines that were experiencing difficulty complying with the DPM standard. As part of these visits, DPM exposures were measured and control technologies for DPM were observed and assessed. Controls consisted of ventilation, clean engines, environmental cabs, alternative fuels, diesel particulate filters (DPF) and work practices. The focus of the follow-up compliance assistance visits was to assess control effectiveness and to make recommendations to mines experiencing difficulty in meeting the DPM standard. At each mine visited, the ventilation controls were evaluated, engine emissions were determined for equipment in use, environmental cabs were examined, and operational practices were noted. Additionally, control technologies, including alternative fuels and DPF were evaluated in several mines. A comparison was made of mine and section airflow to equipment particulate indices. Based on engine emissions, horsepower and operating time, the contribution of individual engine emissions to total emissions was made. Environmental cab integrity, positive pressure and air filtration systems were checked and operational practices relating to DPM exposure were assessed. This paper summarises the preference and magnitudes of controls that were typically used or needed for successful control of DPM. Additionally, results of the assessments of alternative fuels (including bio-diesel and water emulsion fuels) and DPF are presented.

Jan 1, 2005

By G Morgan, C Kemp

In December 2010, a trial of borehole radar technology was conducted to test the usefulness of the technique in better refining the position and geometry of narrow vein orebodies away from the primary data sources of drilling and mapping of development excavations. This paper summarises the reasons why the technique was applied, describes the testing methods selected and summarises the outcomes of the trial.Poor reconciliations of recovered metal from a section of an orebody at Jundee mine site, Western Australia, led to an investigation that identified insufficient understanding of the geometry of a narrow vein orebody as a potential cause. This orebody was situated between mapped development excavations and away from surrounding drill holes. Borehole radar was identified as a possible technique that could supply information on vein location and continuity away from other data sources allowing more accurate orebody modelling and subsequent stope optimisation.A borehole radar instrument (10 - 100 MHz frequency) was inserted into pairs of purpose-drilled boreholes on either side of relatively well-constrained mineralisation and the radar reflection data was collected. This process was repeated in five locations across the mine to represent the most common geological settings, lithologies and orebody varieties encountered at Jundee to determine the suitability of applying the technique in each of these settings. Collected, processed and interpreted radar data was compared to other geology data collected independently for verification and interpretation.Conclusions drawn from the analysis were that the technique could effectively determine the following features of the mineralised veins in the majority of test environments: geometry of veins, magnitude of offsets where structures intersect and orientations of planar structures with short strike length. The technique was very useful in selecting the appropriate structural interpretation where available data could lead to multiple, equally likely, interpretations.CITATION:Kemp, C and Morgan, G, 2012. Using borehole radar to refine orebody interpretations in a narrow vein gold deposit, in Proceedings Narrow Vein Mining 2012 , pp 121-130 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By Henderson J, Ward RG

Dissolved oxygen has been measured directly using a rugged, reliable, accurate electrochemical probe system developed for steelworks application by B.H.P. Central Research Laboratories. Furnace measurements show that the steel is generally supersaturated with oxygen and that oxygen contents vary considerably from heat. to heat. Ladle measurements also show considerable heat-to-heat variations. Analysis in terms of ladle deoxidation chemistry differentiates between carbon monoxide controlled and manganese silicate controlled oxygen levels. Deviations from these levels are sometimes due to aluminium present in other added ladle alloys but in some cases the plant applicability of laboratory derived equilibria is questionable.

Jan 1, 1972

During the period 1981 - 1991, Esso Australia and their Joint Venture partners have discovered about 180 MB of liquids (crude and condensate), 60 MB natural gas liquids and 800 - 1000 GCF of gas. A total of 48 wildcat wells were drilled including 12 new pool discoveries drilled from platform facilities. Significant discoveries include the West Tuna, Kipper, Blackback and Terakihi fields. These four discoveries, contribute to 75 per cent of the total reserves discovered in the last decade and were all high-risk plays. The Kipper discovery, in the pre-Latrobe Golden Beach Group top sealed by volcanics, and the Blackback-Terakihi discoveries, located on the present day continental slope in water depths ranging from 300-700 metres are both the result of successful drilling outside the traditional exploration bounds for the basin. During the last decade, Esso and its partners have spent about A$400M on wildcat exploration activity. The exploration success rate, excluding platform based drilling, has been 50 per cent for wildcat wells. On a technical front, the last decade has heralded substantial improvements in seismic data quality. Peak frequency content in seismic data at the Latrobe Group target levels is now double that of the early 1980s. Significant advances have also been made in our understanding of sequence stratigraphy, geochemistry and geohistory of the basin.

Jan 1, 1992

By Mohamed Mekkawy, William W. Wheaton, Ira Brotman

"The Virginia Port Authority and the U.S. Army Corps of Engineers are partnering to construct the Craney Island Eastward Expansion (CIEE) to meet the dual purpose of extending the life of Craney Island as a dredged material management area and providing land for a state-of-the-art marine terminal. The over 500-acre (200-hectare) expansion provides additional upland dredged material capacity for the Hampton Roads Harbor by constructing perimeter dikes, that once filled, will provide land for the development of a container terminal. In the winter of 2010/2011 the first stage of sand fill was placed, followed by the installation of approximately 12 million linear feet (MLF) (3.6 million linear meters, MLM) of marine PVDs. With over 36 MLF (10.9 MLM) of PVD required to complete dike construction the project will be one of the largest PVD installation project in the U.S.This paper details the challenges associated with the construction of the cross dikes, in particular the design, testing, installation and monitoring of prefabricated vertical drains (PVDs) installed overwater to depths of over 130 feet (40 meters) for foundation improvement in the insitu very soft Norfolk Clay. With expected settlements of 20–30 ft (7-10 m) and 30 percent average strains, the discharge capacity of the PVDs was of particular concern. Laboratory data is presented showing the magnitudes and variability of discharge capacity under different confining pressures in both a straight and buckled condition.The method of installation and monitoring of the marine PVDs in open water included developing a specialized barge and sophisticated positioning and data collection system to verify installation location, depth of penetration and track quantities. An observational method, including material testing, detailed surveys, periodic in-situ testing, and instrumentation, was utilized by the project team to assess the project’s progress and allow for validation of consolidation and strength gain rates and magnitudes."

Jan 1, 2017

By Everett H. Graff, Ray H. Misener

THE Sol de Oro mine is in the province of Nazca, 487 km. southeast of Lima, and 60 km. inland from the coast at an elevation of 1200 m. above sea level. From Lima the mine may be reached in 8 hr. by automobile; 472 km. from Lima to Nazca over the paved Pan-American Highway and 15 km. from Nazca to the mine over a good graveled road. The trip from Lima can also be made in 2 hr. via the Faucett Air Lines which make two stops weekly at Nazca. The [Compania] Aurifera Nazca, owning and operating the Sol de Oro mine, was organized in Lima in 1930 by a group of prominent Peruvian mining men, including Ing. Carlos Alvarez Calderon, Dr. Alfredo Alvarez Calderón, Ing. Hector Boza, Ing. Jorge Félix Remy, Ing. Eulogio Femandini, Sr. Fernando Wiese, and Sr. Julio East. The nine claims in the Sol de Oro group owned by the company comprise an area of 52 square kilometers. Development of the property was not started until 1932 and only then under adverse conditions, owing to lack of transportation facilities. Mining machinery and other supplies could be taken as far as Ica by boat and railroad, but to transport them over the 180 km. of hot, sandy desert from Ica to the mine was a problem. There was no road in those days and only a few of the most venturesome truck drivers cared to contract the hauling. Another problem the company had to face was that of securing adequate labor. The Sol de Oro is in an agricultural region, and was forced to look to the near-by cotton plantations for men. Experienced men were imported from the "sierras," but they did not stay. The men are accustomed to high altitudes and cold climate and cannot easily acclimate themselves to the hot and arid coastal region. As a consequence the company has been forced to hire the inexperienced local laborers and train them for mining. The company has established three separate camps at the Sol de Oro property. Each is approximately one kilometer from the other and connected by auto road. The upper mine camp consists of living quarters for 300 workmen and their families, a general mine office, carpenter shop and timber-framing shed, compressor house, drill-sharpening and drill-repair shop, first-aid station, time office, school and store. At the central or "empleados" camp there is a 200-ton cyanide plant, general offices, warehouse, powerhouse, shops, laboratory, hospital, school, guest house, an 18-room hotel for the single staffmen, and 12 completely modern five-room cottages for the married staff employees. At the lower camp are living quarters for 200 workmen and their families, two general stores, a school and a small theater. Below this camp, along the river, are the company wells and pumping plant supplying water for mine, mill, and camp uses.

Jan 1, 1945

INTRODUCTION The SAIMM publishes technical information on various aspects of the minerals industry through several different media. (a) Monograph Series Books in the Monograph Series are high quality, detailed discussions on specialized topics. (b) Symposium Series This series consists of the proceedings of international conferences which are held in South Africa. (c) Special Publications Series This series covers titles which do not form part of the Monograph and Symposium Series. (d) The SAIMM Journal Papers published in the Journal cover al relevant areas of technical interest by striving for a balanced content and maintaining a consistently high technical standard. (e) School and Colloquia Notes The papers from al local schools and colloquia are published and handed out at registration. Should authors wish to have their papers considered for publication in the Journal, they should adhere to the guidelines outlined below.

Jan 1, 1991