Search Documents

By A. U. Seybolt

DURING the course of experiments involving oxygen equilibrations with a high-purity Pd-5 at. pct Rh alloy, the appearance of a subscale was noted. Most of the heat treatments in a pure oxygen atmosphere were performed at 900°C. The presence of the subscale was noted when the oxygen partial pressure was in excess of approximately 95 mm, up to 1 atm, the highest pressure used. According to available thermodynamic information' on the free energy of formation of Rh2O3 (the only reliably reported solid oxide of rhodium), this oxide should not be stable under these conditions, nor, of course, any oxide of palladium. Extraction of the subscale from the matrix was affected by treatment with aqua regia, and the resulting X-ray diffraction powder pattern is shown in Table I. This pattern is not that of Rh2O3, nor that of any known rhodium or palladium oxide. It can be indexed on a hexagonal lattice with a. = 5.22Å and co = 6.0Å. In addition to this unknown material, there was a weak Rh2O3 pattern. An X-ray fluorescence analysis of the powder gave 3214 palladium counts per sec and 5381 rhodium counts per sec, thus indicating the likelihood of a double oxide of palladium and rhodium. In view of the fact that the above result was obtained on a single sample, it is perhaps best not to insist upon the above ratio of about 0.6, but possibly to tentatively assume 0.5 or 1/1. The small amount of Rh2O3 in the X-ray pattern might have occurred on cooling, and it seems possible that the double oxide, below some temperature level, is not as stable as Rh2O3. To examine this point, some of the extracted double oxide was heated on a sheet of pure palladium in air at 900°C, and allowed to furnace-cool over a period of several hours. The X-ray diffraction pattern of the powder showed approximately the same intensity of Rh2O3 and the "hexagonal" oxide as before, but, in addition, a rather faint pattern of another crystalline species made its appearance. This finding again suggests partial transformation of the major (double) oxide to other oxides on cooling from 900°C. Application of the phase rule shows that only one equilibrium oxide (subscale) could have been present at temperature. Vacuum-fusion, oxygen analysis of the extracted subscale showed 7.7 ± 0.7 pct O. Combining this information with that of the X-ray fluorescence analysis suggests the formula PdRhO. This compound should have an oxygen content of 7.07 pct, which is within the range of error of the oxygen analysis. However, until a more careful stoichiometric study is made, it is suggested that the formula be written

Jan 1, 1965

By G. Asai

The Bureau of Mines has been engaged in a program to increase the utilization of chromium by providing samples to individuals and institutions requesting chromium for research investigations. This report consists of a tabulation of the disposition of chromium samples distributed from July 1953 through June 1961; 109 requests for chromium were answered by providing chromium as electrolytic plate, powder, or wrought forms. The demand for samples reached a peak in fiscal year 1959 and declined to a relatively low level in fiscal year 1961. The largest number of requests came from individuals engaged in mechanical property studies; there were also many requests from those concerned with vaporized metal and physical properties studies. Most noteworthy application for chromium was the experimental use of the radioactive form, Cr[51], in radiotherapy of cancer.

Jan 1, 1964

By Gilbert R. Tallard

"Pouring deep foundations by the tremie pipe method is nowadays such a common process that it has becomes an unspecified practice. Means and methods are almost entirely at the contactor’s discretion. A variety of practices are permitted and seldom associated with the discovery of abnormalities and areas of random defects in concrete. This writer wishes to call the attention of stakeholders to the initiation details of the tremie pour operation.KEYWORDSINTRODUCTIONThe advent of slurry as a means of shoring an excavation of relatively small cross section but of possibly great depth has become part of state of the art in foundations construction, with the substitution of said slurry by concrete to provide the structural end product element through the use of tremie pipes. In appearance, there is nothing more simple than pouring concrete into a tremie pipe through a hopper after the basic work has been done i.e. the excavation or drilling, the cleaning of the slurry, the placement of the reinforcing cage, then the tremie concrete pour is almost a reward for a successful achievement. Force of habit has removed the awareness on the process fundamentals for initiating the pour; a variety of practices used call for a review and a reassessment as a means of reducing construction defects that may result from flawed practices, and and especially we are pouring deeper holes. This writer intends to address this issue focusing both on the drilled shaft and the diaphragm wall industries.TREMIE PIPES AND HOPPERSA tremie pipe diameter needs to be sufficiently large to allow the rapid descent of concrete with a minimum of friction loss and avoiding possible bridging in relation to aggregate size. Impervious joints between pipe sections are essential to prevent slurry “raining” over the concrete which can cause concrete segregation pockets and possibly plug the pipe with damaging consequences. That tremie pipes be long enough to reach the bottom may be self-evident but poorly written specifications can be erratic on that subject and seldom specific in terms of inches. A standard pipe of 10 inches is well accepted throughout the foundations industry; double O rings and spline joints are common and function well if properly maintained. However the practice to cover the joint with the ineffable duct tape indicates that all is not always well with this detail. Also, spline cables may shear in case of very long tremie pipes causing the separation of the tremie pipe requiring a restart in midstream with another probable source of inter mixing of concrete and slurry with subsequent defects."

Jan 1, 2017

By G Capes

A novel open stope design approach is presented that delivered improved performance in a mining area with poor ground conditions at the Olympic Dam mine. During 2019, a large open stope had an unplanned caving event resulting in the inability to extract the planned tonnes and subsequent sterilisation of nearby stopes. A design limitation was the lack of data and understanding around the alteration domain extents, the rock mass strength controls and limits, the failure modes controlling stope stability in the local area, and the use of conventional stope shapes. From the available data and failure observations, it was inferred that the dominant caving failure mode resulted from a blocky rock mass impacted by structure and alteration causing an unravelling failure mechanism. Numerical and empirical analyses were conducted to test this hypothesis and establish strength limits for design. The strength limits for the design were then used to provide a range of outcomes from which future stope design shapes such as chamfered backs could be selected. Three alternate chamfered geometries were selected to trial the innovative designs. The application of this methodology in 2020 resulted in overbreak reduction from >100 per cent in the initial caved stope to

Mar 29, 2023

By R. J. Sheets

In 2009 the Gold Quarry open pit mine, located 11 km northwest of Carlin, Nevada, USA, experienced multiple large-scale slope instabilities of the upper east highwall that reduced gold ore extraction for nearly 18 months. The slope instabilities occurred within a weak, consolidated sedimentary sequence that exhibits strength characteristics that are transitional between soil and rock. Instability initiated as mining exposed the lower clay-rich sub-units of the Carlin Formation (Fm.). This deformation created preferential flow paths that allowed groundwater from the upper sandy sub-units to infiltrate low permeability clay-rich sub-units, thereby enhancing deformation of the slope toe which in turn destabilized the upper portion of the highwall. The outcome was a 160 m high slope instability that had a lateral run-out of 850 m. The effort to return the pit to ore production required both the geotechnical and hydrogeological investigations and the preliminary remediation mining activity to be concurrent. This approach required the development of detailed safety procedures and a requirement to modify the remediation design as new results were obtained. An initial challenge was to mitigate a near vertical, 90 m headscarp with blast induced, localized slope failures. Back-analyses applying numerical modeling indicated that the failure surface did not coincide with initial interpretations based on field observations; drilling results eventually confirmed this alternative failure geometry. The final remediation design incorporated shallower slope geometries and an approximately 3 Mt buttress along the base of the Carlin Formation and bedrock contact to reinforce the lower clay-rich sub-units. The outcome is a stable highwall within the Carlin Fm. following nearly ten years of repeated slope instability, and an example of the necessity to conduct appropriate geotechnical and hydrogeological studies during the early stages of a new layback evaluation or new open pit development.

Feb 23, 2014

By N. A. Gokcen

This Bureau of Mines report reviews and summarizes recent studies of the rates of chlorination of aluminous resources with CO and C12 mixtures with and without COC12. No reaction mechanism could be obtained from the existing results; however, diffusional barriers in the gas and solid layers probably control the chlorination rate in thermogravimetric experiments. Fluidized beds of particles smaller than 0.1 mm appeared to show very little solid layer diffusional barrier. For optimum chlorination the particle size should probably be less than 8 mm, the calcination temperature approximately 700° C, and the chlorination temperature from 650° to 750° C. Relatively rapid chlorination with COC12 in thermogravimetric experiments was attributed partly to the simultaneous supply of reductant and chlorinator by one gas to the sample reaction site. Comparable results for chlorination of fluidized beds with COC12 are not available. Equimolar mixtures of CO and C12 produced the optimum rate of reaction. Addition to the calcine of 10 to 20 wt-pct NaCl accelerated the rate of chlorination, and addition of SiC14 to the gas mixture decreased the rate of chlorination of SiO2 drastically, but at the expense of chlorination of significant fractions of Al2O3. Further research in various areas is suggested.

Jan 1, 1983

By Will H. Coghill, I. L. Feld, G. D. Coe

"INTRODUCTION During the course of research on the beneficiation of the Big Seam iron ores of Birmingham, Ala., an urgent need was felt for quick iron assays of grab samples for mill control. Since the gangue minerals in these ores - quartz, limestone, and clay - all have about the same specific gravity, the use of a specific-gravity method was anticipated as a means of measuring the iron content. The idea of estimating the composition of a mineral mixture by measuring its specific gravity is by no means new. However, the usual method of carry in out this idea proved unreliable when applied to the Big Seam ores. The usual rapid method of determining specific gravity consists of measuring the volume of a known weight of sample that has been dried at high temperature. The inadequacy of this method led to the development of the rapid, modified, specific-gravity determination described in this paper.This work- was an incidental development resulting from research on beneficiation of iron ores by the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and ore producing companies of the Birmingham district."

Jan 1, 1946

By R. Krog, S. Schatzel, H. Dougherty

Longwall coal mine operators in the U.S. are required to ventilate multipanel longwall districts, but may have little or no knowledge about what happens to the ventilation air between the inlet evaluation points (IEPs), bleeder evaluation points (BEPs) and bleeder fans. The effectiveness of bleeder performance can directly influence the ability of a ventilation system to remove and dilute coal bed methane emissions. U.S. coal mining stakeholders have acknowledged their belief that the T-junction split at the longwall face tailgate corner is very important in controlling the distribution of ventilation air. To obtain direct measurements of bleeder performance, a tracer gas, sulfur hexafluoride (SF6), was released into the ventilation air stream on active and inactive longwall panels. Testing was performed on multiple longwall panels that included various phases of longwall development and variable path lengths of ventilation air transport to bleeder fan installations. Changes in the T-junction ventilation air distribution over the life of a longwall panel, and its variable effect on panel ventilation airflow are discussed. These findings will assess the effectiveness of commonly applied ventilation strategies for improving air distribution and ventilation controls to meet statutory requirements.

Jan 1, 2011

By M Olsen, L van den Berg

Bowen Basin coalmines suffer from hot and humid ambient conditions during the summer period. The ambient conditions combined with high VRTs, increasing depth of working and significant equipment heat loads results in heat issues underground. Coalmines operate under heat stress management plans as required by legislation with associated trigger action response plans (TARPs). Some mines also employ refrigeration as part of their heat management strategy.A recent case study was conducted on a mine producing about 4.5 Mt/a from their longwall and experiences summer surface ambient temperatures of about 23.5ºCwb. The expected virgin rock temperature is 46ºC at 300 m depth. The mine currently introduces a modest amount of surface cooling at the portal using ‘off-the-shelf’ air conditioning units. This system does not effectively manage face temperature primarily due to positional inefficiency.Underground conditions remain hot in summer and work is typically undertaken in accordance with the Heat TARP. This has a direct impact on the productivity of crews, worker comfort and also negatively impacts the workforce morale. The mine commissioned a study to determine a refrigeration strategy aimed at maintaining underground conditions below TARP levels 90 per cent of the time.The ventilation network model was calibrated against actual temperature data to simulate the heat loads including longwall, conveyor system, strata and auxiliary diesel fleet. This model was then used to determine the cooling requirements for bulk surface cooling, bulk underground cooling, surface district cooling and underground district cooling strategies.These estimates were used to undertake a total owning cost trade-off for the different strategies. The study concluded that a chilled air shaft has the lowest technical risk but the highest total owning cost due to shaft development needs. Introducing chilled water to an underground cooler via boreholes offered the lowest total owning cost and was therefore recommended.CITATION:van den Berg, L and Olsen, M, 2017. Heat load assessment and mine cooling strategies for a longwall coalmine, in Proceedings Australian Mine Vent Conference 2017, pp 231–236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By H. F. Naldrett

"AbstractAt the end of May, 1950, Imperial Oil, Limited, had completed a total of 192 D-3 wells in the Leduc-Woodbend field, 62 of which lost circulation in the D-3 zone for periods ranging from two hours to fifty days. The majority of the remaining wells •lost some mud without actual loss of returns. In addition, independent operators completed 69 D-3 wells, of which 9 lost circulation. Included among the latter is the now well known Atlantic No. 3 well, which blew wild out of control for seven months. The well was finally brought under control through two directionally drilled wells, but not before the derrick fell and the well caught fire. Practically all known filler materials have been used in attempt3 to prevent or regain loss of circulation, but none has been successful, except in minor cases. Ordinary sawdust has come to be the most commonly used filler material and is added to the mud before the D-3 zone is contacted. In cases of serious loss of circulation, the on1y successful method of getting returns has been the use of a series of small cement plugs.IntroductionThe Leduc field is twenty miles southwest of Edmonton, Alberta. Geologically, it is on the east limb of the Alberta syncline, in the homoclinal belt. The main productive zones are in the Upper Devonian formation and are known locally as the D-2 zone and D-3 zone, respectively (see Figure 1).The D-3 zone is a dolomitized reef with fair average porosity and permeability, and shows considerable evidence of vertical fracturing. Porosity is mainly due to moderately uniform development of vugs which are interconnected by small crevices. However, the formation is known to be, locally, extremely vuggy and in places cavernous. These latter conditions create very serious drilling problems due to the hazard of loss of circulation, particularly in the gas cap, which has a maximum thickness of 200 feet. The D-3 zone is contacted at an average depth of 5,300 feet."

Jan 1, 1950

By Thomas W. Camm

A WINDOWS-based object-oriented expert system for prefeasibility evaluation of hard rock mines is being developed at the Western Field Operations Center (WFOC) of the Bureau of Mines. Designed for use with the Bureau's Cost Estimating System (CES), this expert system assists an evaluator in choosing an underground mining method, and the related design parameters. The system provides the engineering and design guidelines necessary for an evaluator to perform a prefeasibility type cost estimate.

Jan 1, 1992

By G. A. Irons, D. Guo

"The average spout height and width produced by bottom gas injection in a water model of a steel ladle were measured with an image processing technique. It was revealed that the spout height could be described by a Gaussian curve. A combined SIMPLE -VOF model was developed to simulate the liquid surface and flow. The results showed that, though the model produced reasonable velocity distributions and free surface positions, the spout height due to the dynamic head of the rising liquid was substantially lower than observed, indicating that the bubble dynamics at the bath surface play an important role in spout height.IntroductionDue to the enormous importance of gas injection and stirring in metallurgical processes, there have been numerous publications on water and numerical modeling of such vessels. The free surface of the bath has received considerably less attention, despite its importance. At the free surface there are often important chemical phenomena occurring that require a good understanding of the fluid flow; these would include reoxidation of steel, metal splash and fume formation. Furthermore, to understand the details of slag-metal interactions such as slag entrainment, metal losses to slag and the transport phenomena associated with refining reactions, it is necessary to understand the plume and spout interactions first.There have been few experimental studies of the free surface of liquid in gas-injected ladles [1- 3], and even fewer on numerical modeling. Brimacombe and co-workers [1] studied the gas void fraction in the spout region, using a double-tip electrical resistance probe. This sensor cannot distinguish between gas in bubbles about to break and gas in the freeboard. Thus, it is a matter of judgement as to the position of the free surface. Schwerdtfeger and co-workers [2] used a single probe configuration with a wire and a counter electrode in the liquid, so that the height of the continuous liquid phase was unambiguously determined. Irons and co-workers [3] measured the spout height by ultrasonic and electrical capacitance techniques. These techniques were as reliable as the resistance techniques, but were restricted to low flow rates."

Jan 1, 2001

By D. H. Baldwin, R. E. Reed-Hill

DURING the course of experiments involving oxygen equilibrations with a high-purity Pd-5 at. pct Rh alloy, the appearance of a subscale was noted. Most of the heat treatments in a pure oxygen atmosphere were performed at 900°C. The presence of the subscale was noted when the oxygen partial pressure was in excess of approximately 95 mm, up to 1 atm, the highest pressure used. According to available thermodynamic information' on the free energy of formation of Rh2O3 (the only reliably reported solid oxide of rhodium), this oxide should not be stable under these conditions, nor, of course, any oxide of palladium. Extraction of the subscale from the matrix was affected by treatment with aqua regia, and the resulting X-ray diffraction powder pattern is shown in Table I. This pattern is not that of Rh2O3, nor that of any known rhodium or palladium oxide. It can be indexed on a hexagonal lattice with a. = 5.22Å and co = 6.0Å. In addition to this unknown material, there was a weak Rh2O3 pattern. An X-ray fluorescence analysis of the powder gave 3214 palladium counts per sec and 5381 rhodium counts per sec, thus indicating the likelihood of a double oxide of palladium and rhodium. In view of the fact that the above result was obtained on a single sample, it is perhaps best not to insist upon the above ratio of about 0.6, but possibly to tentatively assume 0.5 or 1/1. The small amount of Rh2O3 in the X-ray pattern might have occurred on cooling, and it seems possible that the double oxide, below some temperature level, is not as stable as Rh2O3. To examine this point, some of the extracted double oxide was heated on a sheet of pure palladium in air at 900°C, and allowed to furnace-cool over a period of several hours. The X-ray diffraction pattern of the powder showed approximately the same intensity of Rh2O3 and the "hexagonal" oxide as before, but, in addition, a rather faint pattern of another crystalline species made its appearance. This finding again suggests partial transformation of the major (double) oxide to other oxides on cooling from 900°C. Application of the phase rule shows that only one equilibrium oxide (subscale) could have been present at temperature. Vacuum-fusion, oxygen analysis of the extracted subscale showed 7.7 ± 0.7 pct O. Combining this information with that of the X-ray fluorescence analysis suggests the formula PdRhO. This compound should have an oxygen content of 7.07 pct, which is within the range of error of the oxygen analysis. However, until a more careful stoichiometric study is made, it is suggested that the formula be written

Jan 1, 1965

By David J. Dyet

Computer applications in the past five to seven years have become a typical and necessary practice in most modern geological offices. Manual calculations, interpretations and plotting of data can be, at times, quite tedious, inefficient and lacking in ac- curacy. The introduction of geostatistical and geological software can eliminate these problems. Computer applications in the uranium industry are not new; however, they are constantly being developed. A variety of soft- ware programs are available. Generally, these programs support most geological and geostatiscal applications in uranium mines. The Rabbit Lake Operation - Eagle Point mine in Northern Saskatchewan is a high grade mine, as one such case. Computer applications at the Eagle Point mine have been a mainstay in the geology department, since the mine's collaring in 1991. This paper presents a discussion on descriptions of programs, operations and applications of computers. It also explains and de- scribes the radiometric equipment used at Eagle Point. This pa- per will demonstrate how, by using computer systems, mine site information flows reliably with the involvement of computers.

Jan 1, 1996

By V. Schwinn, P. Fluess, N. Cauderlier, J. Bauer

From a strategic and economic point of view, the development of fine grain high strength steels for long distance pipelines is intensified world wide to satisfy the demand for natural gas in the future.The project related property profiles based on strength, toughness, crack arrest and sometimes resistance against HIC at defined design temperatures require an effective structural refinement using advanced steelmaking and processing in the rolling mill. The microstructure of modern line pipe steels ranges from ferritic pearlitic to ferritic-bainitic and structures where bainite is the dominant component, possibly upgraded by secondary phases. This paper illustrates microstructures and properties of recent orders on line pipe steels both for onshore and offshore application using different processing routes in the plate mill. Examples will be given for SAWL 485 offshore grades, X65 HIC and X70 HIC onshore grades, respectively. Finally, production results of a recent X80 order will be presented.

Jan 1, 2005

By Q Qu

Reliable prediction of longwall gas emission sources and rate plays a critical role in mine ventilation and methane drainage capacity planning. Over the years, Australian longwall mines have been using the historic Winter method and the Flugge method in modelling specific gas emissions (SGE). The predicted results often experience high discrepancies from the operational reality. To improve gas emission prediction, post-mining gas contents were measured in several mines in Qld and NSW by safely drilling core holes into the longwall goaf. The results revealed many new insights into gas emission characteristics from different coal seams and the drawbacks of the European methods in their use in high-production gassy Australian longwall mines. Based on measurement data, a new, time-dependent gas emission prediction model has been developed. Considering several factors such as caving, desorption and production rate, the new model can predict more accurate and meaningful gas emissions to meet today’s needs in mine gas emission management. A case study is provided to demonstrate the application of the new SGE model.

Oct 12, 2022

By F. A. Forward

Introduction The main line of ascent in the development of the nickel industry may be traced back through the International Nickel Company of Canada, Limited, to its earliest antecedents, the Canadian Copper Company and the Orford Copper Company. Mining geology is but one aspect of the overall development of this organization, and the stress it has placed on geology grew according to the need. In the early days, intensive geology was not required because ore supply was not one of the main problems of this or any of the pioneer companies. The difficulty then was to find economic methods for reducing the ores to nickel and copper, and markets for absorbing nickel in the face of a limited demand from consumers heavily prejudiced in favour of the New Caledonia product. "Very early in the history of the region it was patent to everyone that to share in the full benefits of the industry the same individuals or company must control the whole of the operation necessary to manufacture the finished product' (1, p. 45). These conditions were fulfilled for the International Nickel Company in 1902 when the Canadian Copper Company (incorporated 1886), with its ample ore supply, took the initiative to merge its interests with those of the Orford Copper (Refining) Company (incorporated 1887) to form the new company which, with reorganizational changes, emerged as the producer of the overwhelming bulk of the world's nickel. The Mond Nickel Company, Limited, entered the field in 1899 with a refining process, and over a period of years acquired ore through purchase of mining properties. This Company operated successfully and independently until 1929 when its assets were joined with those of the International Nickel Company in order to permit the most economic exploitation of the Frood-Stobie orebody in which both Companies were interested.

Jan 1, 1948

By Lucien Eaton

INCREASED mining activity during the past year has brought to light changes in mining practice and advances in technique, born and incubated in the period of depression from which the mining industry is now emerging. Although the tendency toward large output from individual mines has continued, a salutary trend is evident toward greater efficiency at small mines, in which the gold mines of Canada have led the way. Improvement in excavating machinery and washing plants for small placers has continued, and knowledge of the possibilities and limitations of this kind of equipment has increased. Greater portability through sectionalization has been the keynote. Power, shovels and draglines mounted on caterpillar treads move from one deposit to another under their own power, and floating washing plants mounted on pontoons can be taken down, moved, and set up again by a small crew of men in only a few days.

Jan 1, 1937

By D. Stone, M. Le Roux, Q. P. Campbell, M. Fofana

Float-and-sink analysis is widely used in the coal industry to obtain washability data, yielding important information about beneficiation potential and performance. This method is associated with health and environmental problems, and research into alternative densimetric methods is important. The RhoVol is a new technology developed by De Beers Group Technology South Africa (DebTech) for the image-based generation of densimetric data from ores. The analysis is done on a per-particle basis, within a size range of +3 mm –8 mm. In this paper we compare the established methods used for the float-and-sink analysis of coal with a new method using RhoVol. The aim of the study was to determine the validity of the information obtained from the RhoVol analyser by performing comparative densimetric analysis on three different coal samples. The results showed that the RhoVol method was more rapid, safe, and precise, but tended to consistently underestimate the density of the coal sample, probably due to varying coal porosity.

Oct 3, 2023

By W. H. Ode, W. A. Selvig

"INTR0DUCTIONAccording to the Standard Specifications for Classification of Coals by Rank of the American Society for Testing Materials (A.S.T.M. Designation: D388-38).1/ high-volatile bituminous coals, subbituminous coals, and lignites are classified on the basis of calorific values on the ""moist"", mineral-matter-free basis. The moist basis refers to coal containing its natural bed moisture but not including visible water on the surface of the coal. It is assumed that the natural bed moisture of coal in the ground represents the moisture-holding capacity of the coal when in equilibrium with air at approximately 100 percent relative humidity. This moisture is sometimes referred to as inherent moisture as opposed to extraneous moisture, which wets the surface of the coal.To simplify procedures for determining the moisture-holding capacity of coal it is assumed, for all practical purposes that the moisture content of coal when brought to a standard condition of moisture equilibrium in an atmosphere of 97 percent relative humidity and 300 C. represents the bed moisture of the coal. The A.3.T.M. specifications provide that this condition of moisture equilibrium shall be obtained by bringing the coal to a standard condition of moisture equilibrium at 300 C. in a vacuum desiccator containing a saturated solution of potassium sulfate (97 percent relative humidity) according to the procedure proposed by Stanfield and Gilbart. 4/ No mention is made in the specifications for bringing partly air-dried samples to their natural bed moisture condition probably because of the hysteresis effect that has been noted by various investigators. 5/ In this connection it has been found from sorption studies that the adsorption and desorption curves for lignite are not entirely reversible. The hysteresis effect has been explained by some investigators as resulting from shrinkage of the lignite during drying, which causes a collapse of some of the capillaries, so the dried lignite cannot take up as much water as it held originally."

Apr 1, 1953