Search Documents

By Liang Wang, Sheng-Kai An, Bing Xie, Hong-Yi Li, Cui Li

In order to develop an environment-friendly method for extracting vanadium effectively from aqueous solution containing vanadium, the dynamic adsorption behavior of V by a continuous fixed-bed column which was filled with macro-porous weak base anion exchange resin was studied. Effects of conditions including the bed depth, flow rate, concentration of vanadium ions on dynamic V adsorption were investigated. The optimum adsorption conditions were established at flow rate of 6 ml/min with bed depth of 20 cm. Isotherms studies demonstrated that the column adsorption of V was a favorable chemical ion exchange process in monolayer. Several kinetic models were applied to analyze the adsorption characteristics. Analysis results of the Bohart-Adams model indicated that the adsorption process was dominated by external mass transfer in the initial stage. The Thomas model was appropriate to describe the column behavior, revealing that both external and internal diffusions were involved in the limiting steps.

Jan 1, 2014

By Amar Prakash, V. M. S. R. Murthy, VIVEK KUMAR HIMANSHU, Sufal Mehrotra, Ashish Kumar Vishwakarma

Raises are vertical or inclined openings made to connect two levels of an underground metalliferous mine. They are developed using drilling and blasting-based technique or by mechanical means. Raise boring machines (RBM) have evolved in recent years, which provide quicker and safer raise excavation. The penetration rate using RBM has influenced applied thrust. The required thrust to enhance penetration rate with optimal use of energy would be different under varying geological and geotechnical conditions. In this study, the influence of applied thrust on penetration rate using RBM has been investigated. The investigation has been made for two different rock types, amphibolite (AMP) and garnet-biotite-sillimanite-gneiss (GBSG). The numerical simulation model was developed for this purpose using Ansys-Explicit Dynamics. The induced tensile stress under different conditions of applied thrust has been analysed in the calibrated numerical model. The model output shows the power trend between the parameters. The experimental data on penetration rate was also collected along with the respective operational parameters. A statistical analysis has been carried out for the gathered data. The analysis of data also shows a power trend between thrust per cutter and penetration rate in both rock types and hence validates the numerical simulation-based output. Based on the outputs of the numerical simulation and empirical study of the experimental data, the optimum thrust per cutter for excavation in both rock types is in the range of 12–14 tons. The approach used in this study can be helpful for predicting the optimal operational parameters of raise boring machines under different geological/geotechnical conditions.

May 29, 2023

By A. W. Frolli

This paper, describing the mining and reduction methods and costs at the Oceanic quicksilver mine, is one of a series of similar reports being prepared by the Bureau of Mines on various mines in the United states. The property, which is owned and operated by the Anglo American Mining Corporation, Ltd., is 5 miles east of Cambria, San Luis Obispo County, Calif. It lies in a region of steep hills and sharply incised canyons on the west slope of the Santa Lucia Range at an elevation of about 500 feet above sea level. The climate is ideal for living and operating conditions. A 40-mile paved highway connects the mine with San Luis Obispo, the nearest convenient railroad town.

Jan 1, 1937

By Albert Ladd Colby

PAGE I. Introduction,...........577 11. PRocess of Manufacture. 1. American Specifications. 2. Foreign Specifications, . ......... 580 III. Chemical Properties. I. Chemical Composition: (a) American Specifications ; (b) Foreign Specifications. 2. Chemical Analysis: (a) American Specifications ; (b) Foreign Specifications ; (c) Number of Analyses Required ; (d) Sample for Analysis ; (e) Check-Analyses Impracticable ; (f) Rejection Solely on Variation in Com-' position,............581 IV. Physical Properties. 1. Drop-Test and Drop-Testing Hachine: (a) American Specifications ; (b) Foreign Specifications ; (c) Limits in Deflection. 2. Tensile Test: (a) American Specifications; (b) Foreign Specifications ; (c) Test-Pieces are not Representative ; (d) Specified Tensile Strength is Affected by the Section ; (e) BpeciBed Tensile Strength is Often Inconsistent with Specified Chemistry ; (f) Specified Tensile Strength is Often Inconsistent with Specified Elongation ; (g) Amount of Tensile Testing Required is Excessive ; (11) Conclusions. 3. Dead-Weight Test: (a) American Specifications; (b) Foreign Specifications; (c) Number of Tests Specified. 4. Bending-Test: ((1) American Specifications ; (b) Foreign Specifications,..........589 V. Section. 1. American Specifications. 2. Foreign Specifications: (a) Templets ; (b) Sample Piece of Rail; (c) Allowable Variation from Templet,...........601 VI. Weight. 1. American Specifications. 2. Foreign Specifications,. . 603 VII. Length. 1. American Specifications. 2. Foreign Specifications, . . 604 VIII. Drilling. 1. American Specifications. 2. Foreign Specifications, . 604 IX. Finish. 1. American Specifications. 2. Foreign Specifications, . . 50.5 X. Branding. 1. American Specifications. 2. Foreign Specifications : (a) Data to be Rolled in Raised Letters on Web of Rail ; (b) Marking of the Blow-Number on Each Rail; (c) Additional Marking and Painting of Rails,........605 XI. Inspection. 1. American Specifications. 2. Foreign Specifications: (a) Prior Notice of Rolling; (b) Free Access to the Works ; (c) Cost of Inspection, Analyses and Tests to be Borne by the Manufacturer ; (d) Rails after Inspection by Manufacturer to be Sorted into Lots Prior to Inspection by the Engineer ; (e) Disposition of Rejected

Jan 1, 1907

By M. Kozlowski, I. Candy, S. Kashani-Nejad

The production of ferronickel and matte from nickel laterite ores is dominated by the Rotary Kiln, Electric Furnace (RKEF) process. Over time, major improvements have been made to kiln operation. In particular, kilns are now required to perform substantial amounts of reduction of the metallic oxides, thereby reducing the load on the electric furnace and substituting less expensive fossil fuel for electrical energy. To the basic refractory lined cylinder have been added: internal features such as dams and lifters, aimed at changing residence times in different sections of the kiln and enhancing gas/solids interaction, on-board fans to introduce tertiary air and on-board scoop mechanisms to allow reductant coal additions to be made at advantageous locations along the kiln. Many of these advances in design have been made on a trial and error basis and by 'borrowing' technology from related kiln processes, supplemented by proprietary modeling to various levels of sophistication. This paper presents a conceptual review of modeling components for the development of a computational model for granular material flow, combustion and heat and mass transfer in a nickel laterite kiln. These components include: granular material flow and segregation models for the simulation of bed motion, heat transfer models that simulate heat transfer by turbulent diffusion and radiation and the distribution of this thermal energy within the bed, and fluid flow models for the prediction of combustion aerodynamics.

Jan 1, 2005

By J. Kan

In order to determine the recovery functions in an oil sand circuit it is necessary to have more than a minimal determination the mass flows in the network. This over-determination is essential in order to allow for measurements within the flow matrix "to flex" according to an error function. It is then possible to identify the flows and composition at all points with maximum likelihood. These so-called full mappings are not easily obtained. However, in order to obtain an unequivocal determination of all the unit operations recoveries such a balance is needed. When databases are constructed exclusively with coherently balanced sets of data it is possible to obtain a maximally accurate process model by maximizing the probability of correctly identifying the process causality. Indeed, it is doubtful in cases of normal complexity that any sense can be made of data that is not so balanced. Coherent mass energy balancing is a tool developed by mineral processing scientists and engineers. Its rigorous application to oil sands is the subject of this paper. The additional element associated with hydrocarbon requires special considerations. It is shown that at least one currently available mineral processing tool will solve the full-mapping problem for an oil sand operation. Experimental design constraints are discussed in this paper relating to the development of databases for the development of effective process models.

May 1, 2004

Reduce the potential of haulage related injuries in underground mines by providing a method for quickly assessing the state of repair of mine haulage track. The Problem Currently, there are no established standards or procedures for inspection or cleaning of underground mine haulage track. Many track defects are hidden from an inspector because of layers of dirt and debris on the ballast, spikes, fishplates, etc. When a visual inspection can be performed, it may be highly subjective, except for a few items that can be categorized or counted, such as missing bolts or spikes. Track inspectors may even become tolerant of defects that can gradually worsen. For these reasons, mechanical inspection methods are needed to supplement visual inspections. Approach The Bureau investigated this problem and designed a towed vehicle to both mechanically clean and inspect underground coal mine haulage track. The vehicle was developed using a systems approach, paying particular attention to human factors issues such as operator field of view, operator ingress-egress, control positioning, and seating design. The prototype was built using simple fabrication techniques and off-the-shelf components.

Jan 1, 1990

By J. Sohn

The most promising near-term alternative to fuel cell driven vehicles is probably Hybrid Electric Vehicle (HEV or EV) technology. HEV technology combines the best characteristics of fuel-driven engines, electric motor drives, and energy storage components. It is designed with a combustion engine that functions as the primary power source, and an electric power storage system that functions as the secondary power source. The presence of the secondary power source allows designers to size the combustion engine for cruising power requirements. A new energy source for HEV or EV market will become lithium ion batteries (LIBs) in the near future. LIBs for HEV or EV has large scale about more 10,000 times than small size one for IT devices in order to achieve high electric density/capacity and high efficiency, etc. In those reasons, physical treatment of the batteries is more difficult for stable dismantling in comparison with the smaller one. Hybrid vehicle sales will grow by nearly 400 percent during the next seven years, according to a new report from analyst firm ABI Research. By 2013 hybrids will make up 6 percent of annual U.S. auto sales. The traction battery pack will become air-cooled LIBs which consists of several modules of Li ion battery and connected in series/parallel configuration to provide about >450 VDC, >150 kW peak power, and >80 Ah capacity. As the use of these batteries tends to increase significantly for the next years, it is relevant issues that development of new recycling methods as well as optimization of existing processes to treat spent LIBs for HEV have being addressed in order to obtain sustainability. In this study, physical treatment containing stable electrical discharge of spent LIBs for HEV was carried out for recovery of valuable metals from the batteries. Also In order to increase the yield of valuable metals through physical treatments such as electric discharge of spent batteries, crushing, and classification, we also focused on the recovery of cobalt from +8 mesh fraction due to its large portion in crushed intermediates.

Jan 1, 2010

By F. Z. Suo

Baoahan Iron and Steel Complex is situated at lower beaches of the Yangtze River. The subsoils 50~70 M below the surface is a deposite of Yangtze River delta, consisting mainly of weak silty clay and loam, with low soil bearing capacity. Consequently, to build on such a weak soil a grant iron and steel integrated works weak soil improvement at the Complex, pile foundation is the effective type. It is estimated that at the first stage of Baoshan project 60,000 piles have been driven, of which 60% are steel pipe piles and 40% reinforced concrete piles. To provide reliable basis for pile foundation design, on-site loading tests were carried out for long reinforced concrete piles 27,45 60 M in length ,with strain gauges on the chief reinforcement of pile shaft and strain rod on pile tip. Based on loading tests, the paper discusses and analyses some issues, including determination of load transfer mechanism distribution of frictional resistance. Tests show that as far as long friction piles in soft clay are concerned, regardless of the properties of pile tip's bearing stratum, loads are mainly carried by shaft frictional resistance which it is effective to determine pile capacity in terms of P ~ S relationship.

Jan 1, 2010

By J Lombardi

OZ Minerals' Prominent Hill copper-gold concentrator is located 130 kilometres south east of the town of Coober Pedy in the Gawler Craton of South Australia. The concentrator was built in 2008 and commenced commercial production in early 2009. The Prominent Hill concentrator is comprised of a conventional grinding and flotation processing plant with a 9.6Mtpa ore throughput capacity. The flotation circuit includes six rougher cells, an IsaMill for regrinding the rougher concentrate and a Jameson cell heading up the three stage conventional cell cleaner circuit. In total there are four level controllers in the rougher train and ten level controllers in the cleaning circuit for eighteen cells.Generic proportional – integral and derivative (PID) control used on the level controllers alone propagated any disturbances downstream in the circuit that were generated from the grinding circuit, hoppers, between cells and interconnected banks of cells, having a negative impact on plant performance. To better control such disturbances, FloatStar level stabiliser was selected for installation on the flotation circuit to account for the interaction between the cells. Multivariable control was also installed on the five concentrate hoppers to maintain consistent feed to the cells and to the IsaMill. An additional area identified for optimisation in the flotation circuit was the mass pull rate from the rougher cells. FloatStar flow optimiser was selected to be installed subsequent to the FloatStar level stabiliser. This allowed for a unified, consistent and optimal approach to running the rougher circuit. This paper describes the improvement in the stabilisation of the circuit achieved by the FloatStar level stabiliser by using the interaction matrix between cell level controllers and the results and benefits of implementing the FloatStar flow optimiser on the rougher train.

Aug 8, 2011

By P. Diehl, M. David

"As shortage in the supply of mineral commodities become more probable, there is an increasing need for reliable and comparable reserve/resource data. It is therefore necessary to standardize the traditional classification procedure by quantifying the three basic criteria in resource evaluation: economic feasibility, geologic assurance and recovery. For the portion of fairly well documented deposits and as far as their geologic parameters are concerned, geostatistical methods can considerably improve the quality of ore classification. In respect of economic feasibility and recovery, approved geostatistical methods can be introduced directly into the classification procedure. The concept of geologic assurance, however, requires a new interpretation in terms of geostatistical error spread. As the ""risk"" in estimating an ore parameter is also a function of the respective block size, it is reasonable to define not only upper limits for the risk intervals for each class of uncertainty, but also block dimensions which reflect the typical stage of planning associated with the different ore categories. An algorithm has been developed to block out areas inside a mine or a large panel which satisfies the constraints of an ore category in respect of the risk intervals of a parameter and in respect of their size. The method has been computerized and is demonstrated on a massive copper-nickel deposit.IntroductionFacing an uncertain future with respect to the demand and supply of mineral commodities, both governmental authorities and the mining industries show an increasing interest in a useful framework for the assessment and classification of the remaining mineral resources"". This is reflected by the recently published appraisal and classification scheme of the United Nations as well as by the new or revised classification systems of the USA; Canada or Australia. Moreover there are various classification schemes which are currently discussed in major mining companies."

Jan 1, 1982

By M. R. Yalamanchili, J. D. Miller

Discussion by M.R. Yalamanchili and J.D. Miller The authors, M. S. Celik et al., should be recognized for their efforts to describe the flotation behavior of boron minerals. In the case of borax and other soluble salt minerals, analysis of the flotation chemistry has been difficult because of the high ionic strengths associated with these soluble salt systems. However, considerable progress has been made in this area, and recently a surface charge/collector colloid adsorption model was proposed by Miller and his coworkers to explain the collector adsorption phenomena observed in soluble salt flotation systems (Milleret al, 1992; Yalamanchili et al., 1993; Miller and Yalamanchili, 1994; Yalamanchili and Miller, 1994a: Yalamanchili and Miller, 1994b). In this work, the sign of the surface charge of alkali halides in their saturated brines was established on the basis of nonequilibrium electrophoretic mobility measurements by laser-Doppler electrophoresis (Miller et al., 1992). Generally, these results are what would be expected from the simplified lattice-ionhydration theory. This electrokinetic information coupled with the stability and prevalence of collector colloids in such soluble salt flotation systems indicates that the selective flotation of alkali halides is due to the adsorption of oppositely charged collector colloids by heterocoagulation. Experimental flotation/bubble attachment results for 21 different alkali halides (Yalamanchili et al., 1993; Yalamanchili and Miller, I994b) confirmed that the flotation response of soluble salt minerals with weak electrolyte collectors can best be explained by the adsorption of oppositely charged collector colloids rather than by the adsorption collector ions and/or neutral molecular dipoles as originally suggested by many researchers (Fuerstenau and Fuerstenau, 1957; Schubert, 1967; Roman et al., 1968). In addition, the flotation of certain alkali oxyanions (Pizarro et al., 1993) and double salts such as schoenite and kainite can be explained by the same collector colloid adsorption mechanism (Miller and Yalamanchili, 1994). The borax flotation results reported by Celik et al. need to be examined in terms of the above mentioned surface charge/ collector colloid adsorption model. Unfortunately, the authors seem to be unaware of this recent work that nicely describes soluble salt flotation with weak electrolyte type collectors such as amines and carboxylates. In view of our past work, the flotation characteristics of borax were of particular interest, and, in this regard, the results of dodecyl amine flotation of borax reported by Celik et al. have been examined in further detail in the light of experimental results from our laboratory. In our research, a vacuum flotation technique was used to study the flotation response of borax (Na2B407.10H20), which has a solubility of 39 g/L at 25 °C) with dodecyl amine hydrochloride as collector. These chemicals were purchased from Eastman Kodak and used as received. Saturated solutions of borax at desired pH values were prepared by continuously stirring the salt solutions over a period of about 10 hrs. It should be mentioned that the conditioning time to achieve equilibrium is an important variable and can significantly change the flotation response of some soluble salts (Yalamanchili et al., 1993). Collector was added to the saturated borax solutions containing about one gram of 100x 150 mesh borax particles, and conditioning was done for about 20 minutes prior to flotation. The borax flotation recoveries from saturated brine are presented in Fig. 1 as a function of collector addition at the natural pH of 9.3, as reported both by Celik et al. and as measured in our laboratory. In addition, the region of precipitation for the dodecyl amine hydroborate is included in Fig. 1. It can be seen in Fig. 1 that the flotation response curves are separated by about one order of magnitude in R12NH3CI collector addition. The flotation results of Celik et al. show that the maximum borax recoveries can be obtained below the solubility limit of the dodecyl amine hydroborate collector. However, in our experiments borax flotation seems to occur only after the precipitation of the dodecyl amine hydroborate collector as might be expected from the collector colloid adsorption model (Yalamanchili et al., 1993) if borax were negatively charged. Further analysis by nonequilibrium and equilibrium electrophoretic mobility measurements for borax indicates that borax is negatively charged at the natural pH of 9.3, as discussed below. The reliability of the nonequilibrium electrophoretic measurements has been demonstrated previously for alkali halides and alkali oxyanions (Miller et al., 1992; Miller and Yalamanchili, 1994). The equilibrium and nonequlibrium electrophoretic measurements for borax were found to be consistent and are presented in Table 1. These results provide clear evidence that borax carries a negative surface charge in its saturated brine (pH 9.3), and the sign of the surface charge of borax reverses and becomes positive if the pH is reduced to 8.6. The equilibrium between borax and its saturated brine can be described by the following reaction: [2Na2B407.1OH2O-4Na++B407=+HB4O7 +OH+19H20] It appears that the oxyanions of the borax lattice provide

Jan 1, 1995

By C Wels

Current best management practice requires the placement of a cover onto most types of mine waste including tailings, waste rock and/or spent heap leach rock at closure of the mine. The objectives of a cover system may vary from site to site but generally include dust and erosion control; chemical stabilisation of acid-forming mine waste (through control of oxygen ingress) contaminant release control (through control of infiltration); and/or provision of a growth medium for establishment of sustainable vegetation. In our experience, there has been a general tendency by stakeholders to develop performance criteria for cover systems, which are tied directly to these specific design objectives. In many cases, this practice has led to the development of single, often very conservative, numerical values of cover performance criteria such as ænet percolationÆ, ærate of oxygen ingressÆ and/or æplant density/mixtureÆ. In our opinion, there is a need to develop cover performance criteria on a case-by-case basis and with due consideration of the short-term and long-term impacts on the receiving environment at a particular site. This paper puts forward a methodology for developing site-specific performance criteria for a cover system designed to isolate acid-forming mine waste and to control acid rock drainage. The proposed methodology links the predicted performance of a cover system to groundwater and surface water impacts. This way, the appropriate level of control (of oxygen ingress and/or net percolation) required by the cover system can be determined. A case study is presented that illustrates the application of the methodology proposed in this paper.

Jan 1, 2003

By George F. Weaton

Although an almost continuous campaign had been carried on by various experimenters since 1885 to find a commercial process of smelting zinc by electrothermic means, no commercial success was attained in the United States. The St. Joseph Lead Co., appreciating the theoretical possibilities of such a process, such as the ability to construct units of large capacity, quality control, and the possibility of treating complex and refractory ores, decided in 1926 that the process was worthy of further investigation, and in that year, at one of its southeast Missouri plants, began the development of the electrothermic zinc-smelting process according to the invention of the late Earl C. Gaskill. Late in 1929 the process reached a stage of commercial significance, and in 1930 the erection of a modern electrothermic zinc smelter was begun, at Josephtown, Beaver County, Pa. The site is 3 miles from Monaca, which is on the main line of the Pittsburgh & Lake Erie Railroad, and a spur of the railroad has been constructed to the plant site. The site borders upon the Ohio River, which is navigable for 600 to 800-ton barges. This district was selected for the plant after an economic survey involving such questions as cost and availability of electric power, reduction fuel, transportation facilities, and the transportation charges on raw and finished materials, labor conditions, and taxes. The initial unit of the plant was designed to treat daily 120 tons of 58 per cent zinc sulphide concentrates from the company's mines in St. Lawrence County, New York. The plant equipment is housed in seven modern steel-frame buildings, and includes: Roasting and Acid Plants 3000-ton concentrate storage. Two Nichols-Herreshoff 21 ft. 6-in. diameter, 12-hearth roasters with usual cast-iron airshaft supporting chromium-alloy rabble arms and rabbles. SO2 gas purification system consisting of: One double-compartment hot-dust Cottrell precipitator. Cast-iron sinuous air-contact gas cooler.

Jan 1, 1937

By M Astorga, J Jackson, J Gaunt

The Ban Houayxai mine (BHX) is a relatively low-grade, low-cost, open pit gold-silver deposit in Laos operated by Phu Bia Mining, a subsidiary of PanAust. The ore production rate at BHX is 4.5 Mt/a, with direct tipping to a semi-autogenous grinding/ball mill circuit with a carbon-in-leach process plant. Approximately 100 000 oz of gold is produced per annum.The operation is located in mountainous terrain with minimal run-of-mine stockpiling. This results in limited capacity for blending from stockpile, with the mill instead reliant upon direct feed ex-pit. Since commissioning in 2012, the plant has seen significant variation in milling rates due to variability in the feed properties of the oxide, transition and primary ores. As part of an ongoing continuous improvement program, an integrated approach was initiated, focusing on maintaining and enhancing production in the future as the proportion of harder primary ore increases. This will specifically focus on direct blending from the loading face using the ore properties and blast fragmentation to maintain mill throughput.This approach was based on the concept of physical assets management, commencing with improving information and knowledge of the condition of the orebody through modelling the characteristics, variability and performance of the feed for processes relevant to throughput. These models are used to support both mine and process plant production planning.The key ore feed characteristics and parameters modelled for the life-of-mine are blastability index, powder factor, crushability or impact resistance and grindability. These predictive spatial models were based on the data from diamond drill holes used in resource definition and geotechnical drilling programs by integrating geotechnical, geological, geochemical and metallurgical data.At the early stages of implementation, the models are being utilised for ore blending decisions to provide guidance and support for budgeting, long-term mine planning, blast design for mill feed and providing the mill with an expectation of performance.CITATION:Jackson, J, Gaunt, J and Astorga, M, 2014. Predicting mill ore feed variability using integrated geotechnical/geometallurgical models, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 165–176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Xubo Chen, Zhiqiang Hu, Zhijian Sun, Gaoyun Zhou

"The research aimed at developing an efficient and environmental frother,which was applied in the flotation of sulfide ores. The flotation properties of an efficient frother and pine oil have been studied relatively by flotation tests of lead and zinc sulfide ores. At the same time, the biodegradability of two kinds of frother has been studied by the method of biological respiratory curve. The test results show that the flotation properties of new frother are superior to pine oil such as flotation rate, dosage etc. and its biodegradability is superior to pine oil. INTRODUCTION Frother is a kind of important agent in flotation reagents.In practice, the criterion of the foaming performance of the frother is what is high and low according to flotation indexes. The difference of different minerals and flotation technologies has great influence on the foaming performance of frother, and it is very important to choose the corresponding frother. The type, dosage and selectivity of frother in flotation process must be considered carefully. In today's society, environmental protection and ecological protection are becoming more and more important, and the environmental and ecological damage from mine development has aroused increasingly more attention. The use of mine agents has promoted the development of mineral resources, greatly improves the recovering utilization of mineral resources, at the same time, the production and use of mine reagents also inevitably bring about pollution, and result some influence or damage in the ecological environment.The frother is a common kind of reagent in the flotation process of the concentrator. In many cases, the waste water in the concentrator can not be let out in the natural water because the higher content of the frother in the waste water results in higher index of COD.This will inevitably increase the cost of waste water treatment in the mine.Therefore, the choice of frother should not only consider its influence on the flotation index, but also consider its influence on environmental protection. Waste water treatment is a way to solve the waste water pollution, but it needs to cost a lot of fund, manpower and material resources.And the development of high efficiency pollution-free reagent is a good way to reduce the production cost of mining enterprises and reduce the environmental pollution."

Jan 1, 2018

By Charles Vaught, Warren G. Lacefield, Ronald D. Wasielewski, Philip K. Berger, Henry P. Cole, John V. Haley, Shannon L. Price

A comprehensive review of published research was carried out to identify methods for teaching and assessing critical but nonroutine skills needed for coping with emergency situations. Computerized searches of the relevant data bases were carried out, along with identification of relevant articles and materials by personal contact with experts in many fields. The citations listed in this bibliography resulted from this systematic literature search and review. The computer searches and an analysis of this literature are described in technical report 1. Specific methods for assessing critical skills proficiency in aviation, medicine, organization management, the military, and other industrial/ technical workplaces were described. The potential application of these methods for teaching and assessing (1) critical first aid and (2) self-rescue and escape skills to underground coal miners in annual refresher training was explored. Research and development activities that may improve mine health and safety training were suggested. Most of the entries in this bibliography were assembled in 1984 through 1985. Study of these materials contributed to the completion of the project research that followed. This later work is reported in the project technical report 2 and the final report. This bibliography is most useful when combined with examination of technical reports 1 and 2 and the final project report.

Jan 7, 1988

By Joo Hyun Park, Hyun-Sik Park

"Gold is one of the most valuable and precious metals. But, the extraction efficiency of gold from natural resources is very low and labor-intensive due to very low concentration of gold, i.e.,1–5 ppm, which means that gold extraction processes produce extensive amounts of tailings. The gold content in printed circuit boards (PCB) from waste mobile phones is about 100 to 400 ppm, which is enormously greater than the concentration found in natural ores. Consequently, processes for recycling waste PCB and gold mine tailings become of increasing importance to maintain a sustainable society. As processing these waste materials by pyrometallurgical methods has become more economically attractive, understanding the thermodynamic behavior of gold in smelting slags under oxidizing and reducing conditions has become increasingly important. Therefore, in this study, the effects of slag chemistry, oxygen potential and temperature on gold solubility in smelting slags are discussed. From the results presented, the predominant species of gold is strongly dependent on the basicity of slag. Furthermore, more basic slags showed higher solubility of gold at a given oxygen partial pressure, and more oxidizing atmospheres enhanced the dissolution of gold to the molten slag phase. As a consequence, careful control of the slag composition during pyro-processing of gold-containing waste materials is required to maximize gold recovery. INTRODUCTIONGold has good physicochemical properties. Thus, it plays an increasingly important role in industrial applications. For example, over 300 tons of gold are used annually in electronic components (Hageluken &Corti, 2010).However, 75% of all gold ever produced has been extracted since 1910 and gold reserves in the world are becoming rapidly depleted (Louis & Pluchery, 2012).The cost of gold production and its price in the market have increased rapidly during last 20 years as shown in Figure 1, and interest in the recycling of gold-containing materials has naturally increased.The wastes from electronic equipment (e-wastes) contain large amounts of precious metals compared to their own respective ores, and therefore such wastes may be considered as a secondary source of valuable metals. For instance, the concentration of gold in natural ore is commonly 0.5–15 g/ton-ore (0.5–15 ppm), while its concentration in electronic circuit boards is over 10 times higher, typically being about 150 ppm in expansion cards and over 10,000 ppm in central processing units(Barbieri et al., 2010).Also, gold mine tailings are discharged after the flotation process as slurry form then stored near the operating plants (approx. 100 ton per day in one Korean gold mine). Gold mine tailings contain gold at about 1–2 g/ton. This is the reason why Au-containing materials such as e-wastes and mining wastes are highly important sources of gold (Yamasue et al., 2009)."

Jan 1, 2017

By George McArthur

GEOLOGY One of the largest copper resources in North America occurs in the Bingham mining district, located 40 km (25 miles) southwest of Salt Lake City, UT. Anaconda's present contribution to the development of this resource is the Carr Fork mine. (Fig. 1, Bingham district plan map.) The Carr Fork story began about 300 million years ago when a thick sequence of sedimentary quartzite and limestone was deposited in the Oquirrh Basin. Subsequent earth stresses formed a series of west-northwest-trending overturned anticlines and synclines that were later offset by northwest-striking thrust faults and northeast-trending normal faults. (Fig. 2, Bingham district cross section.) About 38 million years ago the Bingham stock was intruded into some of the folds, resulting in the formation of porphyry ore in the intrusive, and fissure, replacement, and skarn ore deposits in the sediments. The Carr Fork skarns were formed preferentially in two limestone units, called the Yampa and Highland Boy, which average about 46 m (150 ft) in thickness, separated by about 76 m (250 ft) of quartzite. Copper mineralization consists almost entirely of chalcopyrite associated with pyrite and molybdenite in a gangue of garnet, diopside, magnetite, quartz, and carbonate. Molybdenum, gold, and silver are economic byproducts. (Figs. 3 and 4, indicated ore in plan and section.) EXPLORATION HISTORY The West Mountain mining district, of which Carr Fork is a part, was organized in 1863, after leaf-silver ore was discovered in the Carr Fork of Bingham Canyon. However, it was not until 1873, when the Bingham and Camp Floyd railroad to the town of Bingham was completed, that the mining camp flourished. Many small mining companies in the district were reduced, often through consolidation. By 1937 only the National Tunnel and Mines Co. was active in the Carr Fork area. In 1948 it declared bankruptcy, and was later purchased by The Anaconda Co. Anaconda conducted geologic investigations in the Bingham district until 1968, when a concerted diamond drilling program was initiated to fully evaluate the geologic potential of the Carr Fork area. The exploration program commenced with one diamond drill, but was enlarged to three drills following discovery of the first major ore intercept. Near completion of the exploration effort, large oil well rotary drills were used to drill to depths of 762 to 914 m (2500 to 3000 ft), after which the holes were completed by standard diamond drilling techniques. All holes were collared vertically, but considerable deviation occurred because of structure and rock conditions. Wedging and directional drilling were used to keep the holes on target and to provide multiple ore intercepts in the deeper holes. Geophysical surveys, in-

Jan 1, 1982

By Vladimir Lobanov, Vladimir Skorohodov, Boris Radionov, Olga Makovskaya

"The synthetic sorbents and the activated carbons which are used for the metals extraction from weak process liquors are rather expensive. It is propose to use mineral and synthetic high-porous substances which sharply increased sorption properties by special processing. For achievement the desirable properties sorbents are impregnated by specially prepared solutions. Such solutions should contain the substances or its anionic forms which on the one hand are strong enough fixed in a supporter pores, with another are capable to form the insoluble compounds with extracting metals. Selectivity is provided by chemism of the reagent interactions with extracting metal. Due to the high concentration of a reacting ion in a sorbent phase the capacity and rate of sorption increases. Formed insoluble compound remains in a phase of the sorbent and necessity of its filtration disappears. For synthesis the sulfhydryl compounds which chemical properties allow to increase degree of extraction and capacity of the activated carbon were used. At hydrometallurgical processing of precious metals mineral raw materials the commercial solutions with the concentration of gold from 0,1 to 5 mg/dm3 are received. Commonly gold is precipitated from cyanic solutions by the zinc dust. The sorption methods are widely applicable. But the synthetic sorbents and the activated carbon using to these purposes are rather expensive. Expenses for sorbents even at its regeneration can reach 10-15 % from total expenses of gold extraction from ores. When sorbent regeneration, mostly for carbon, is not provided, this share increases to 30-40 %. Thereupon search of the sorbents combining availability, the sufficient capacity, demanded degree of extraction and the low price is actual. For the specified purpose it is offered to use the mineral and synthetic high-porous materials which sorption properties are sharply rose by special treatment. Among such substances are natural zeolites, silica gel, lignine et al. Similar treatment can improve the sorption properties of sorbents used in practice, particularly, the activated carbons. The simplest treatment of potential sorbents consists in its impregnation by specially prepared solutions. Such solutions should contain substances or its anionic forms - impregnating agents. These agents should be on the one hand strong enough fixed in a carrier pores, on the other hand are capable to form with extracting metals insoluble compounds. The more strong compounds are formed the high degree of metals extraction from solutions. The sorbents with similarly changed properties are named the impregnated sorbents."

Jan 1, 2008