Search Documents

By Seong-Taek Lim

Recently, 7xxx aluminum alloys have been evolved into new variants for thick semiproducts which have low amount of 2nd phases and low quench sensitivity. Commercial 7xxx alloys, especially in the thick forgings made of big ingots, often entail microstructural inhomogeneities and concurrent poor mechanical properties due to limited heating ranges and slower quench cooling. In this study, high strength aluminum alloy 7175 and 7050 are adjusted as an attempt to control the equilibrium phases (M-, T- and S-phase) to have optimum microstructure for the thick forging applications. The effects of the relative content of (Zn, Mg, Cu) on the evolutions of the coarse equilibrium phases, hardening response and resultant mechanical properties are investigated. Equilibrium phases (M,T,S) are evolved depending on the constitutional effect, primarily the change of Zn:Mg ratio, and cooling rate following solutionizing. The formation of the T- and S-phases is effectively controlled, and M-phases are homogeneously precipitated in the adjusted (dilute and high Zn:Mg ratio) alloys. It provides extended heating range and lower quench sensitivity than conventional alloys. The attempts ensure the microstructural homogeneity and improved properties, and is expected to be uniquely applicable in 7xxx thick forgings.

Jan 1, 2004

By E. Kalhan, C. Kincal

One of the biggest problems in open pit mining is slope stability. The avoidance of slope stability problems depends on a comprehensive assessment of environmental and operational factors such as geology, climate, and mining activities. In the light of these considerations, slope geometries should be determined in accordance with engineering principles. In this research, the slope stability of rock slopes in a mine opened in a gneiss geological unit has been studied. Production activities were ceased in 2019 due to the slope movements in the eastern part of the quarry. In order to safely continue the production, field works were primarily carried out. To assess slope stability, detailed discontinuity surveys were carried out on bench faces. Subsequently, kinematic and numerical analyses were employed to identify geometries that are expected to maintain stability under the prevailing geological structures and environmental constraints. Engineering geological studies such as scanline measurements in steps and investigation of potential failure mechanisms by kinematic analysis technique were carried out. Small module reactor and Q-slope rock mass classification systems were used to evaluate slope stability. Based on these classification systems potential unstable rock slopes were identified and thematic maps were created using geographic information systems. The most suitable slope geometries are suggested for these slopes. In addition, the improvement methods suggested by the rock mass classification systems were proposed for these slopes.

Sep 1, 2025

By G. G. Marino, J. W. Mahar

This paper provides an understanding of the behavior and potential damage of homes resulting from sag-type mine subsidence. This is done with extensive research of numerous case histories in Illinois collected by the authors. The house response to subsidence-induced ground displacements are summarized and evaluated. A damage level criteria, specifically developed for residential structures, is presented based primarily on repair costs. Damage levels and the associated subsidence profile characteristics for each case history are compared.

Jan 1, 1986

By Davide Onesti

Electrode regulation is the technology at the heart of the AC and DC Electric Arc Furnace. As such, in the last decade it underwent continuous improvement to maximize the EAF performances, in terms of process efficiency, machine utilization and operator safety. Given this background, Danieli Automation’s efforts in the field of electrode regulation have been focused on fast response to scrap cave-in, compensation of supply variations, automatic resonance detection, transformer protection, dynamic regulation of the electrical and chemical set-points, coordination and control of slagging and foaming agents, arc irradiance supervision. An extensive analysis of operator utilization and feedback was also carried out to develop an innovative system HMI. In this field, the choice of the variables shown to the user is the key aspect to allow a prompt process evaluation by the operator, who can refer to a condensed set of useful data. This paper will describe the innovative features and embedded models of the electrode regulation module (Q-REG+) and the supervision HMI, together with the effects of their application on EAF process efficiency and system usability.

Oct 30, 2017

By M. Murphy

The multibillion dollar cost of cleaning up thousands of environmentally contaminated sites across the country created by decades of inadequate disposal of hazardous waste has led to a search for "deep-pocket" sources of cleanup funds. The resul1:: is the emergence of a growing body of law that could have a profound impact on commercial financing transactions and other investment activities when present or past owners of contaminated property are involved.

Jan 1, 1988

By T. B. Szwilski, R. D. Begley

Status of ISO 14000 standards. The ISO 14000 are voluntary international standards providing a frame-work that allows a company to integrate an effective environmental-management system (EMS) into its operations. The purpose of an EMS is to provide a systematic procedure to identify the environmental aspects of a company's activities, evaluate any significant impacts and use the information to set objectives and targets toward continuous improvement of the company's environmental compliance and performance. In addition to the specifications for certification, ISO 14000 can be used as a guide to develop an effective environmental-management system or for self-declaration. The International Organization for Standardization (ISO) is a worldwide federation founded in 1947 to promote the development of international manufacturing, trade and communication standards. The organization is now represented in 118 countries, with the American National Standards Institute (ANSI) representing the United States. The principal goals of the ISO is "to promote the development of standardization and related ac¬tivities in the world with a view toward facilitating the international exchange of goods and services and to develop cooperation in the sphere of intellectual, scientific, technological and economic activity." ISO develops standards with input from government and industry. Because the standards are voluntary, there are no legal requirements to pressure countries to adopt them. However, many governments, industries and US agencies are adopting the ISO standards as a requirement for business trans¬actions, thereby, compelling suppliers to adopt ISO standards. These business and market forces, which are likely to be strategic business issues in the 21st century global marketplace, are imposing the need to develop a systematic approach to environmental management. The ISO 14000 series evolved from a United Nations Conference on the Human Environment in 1972. It includes a broad range of elements: the basic environmental management system, environmental auditing criteria for internal and external auditors, criteria for environmental performance evaluation (EPE), environmental labeling criteria and life-cycle assessment methodologies. The standards comprise two categories: organization evaluation standards and product oriented standards (Table 1). The ISO 14001 specifications contain the requirements for developing an environmental-management system that may be objectively audited for certification. The ISO 14004 standard provides guidance on interpreting the ISO 14000 specifications for the development and implementation of the EMS and for coordination with the management system of the company. On Sept. 1, 1996, the American National Standards Institute (ANSI) and the Registrar Accreditation Board (RAB) signed a formal agreement to create a new entity called the National Accreditation Program (NAP). To obtain certification, a company must fulfill the requirements outlined in ISO 14001. It is required that "a third party give written assurance that a company's EMS meets all the requirements of ISO 14001." Preparing for ISO 14000 can include subscribing to voluntary environmental initiatives; learning from ISO 9000 quality-management experiences; and utilizing information from recognized training courses, publications and numerous Internet resources. Once committed to an EMS, the management should provide sufficient resources to achieve continuous environmental-performance improvement, as outlined in an environmental policy. A thorny issue now being debated concerns the potential liabilities of documenting the environmental performance of a company. General impact of the ISO 14000 EMS standards. With increasing stakeholder awareness, costly end-of-pipe pollution-control approaches and the success of ISO 9000 quality-management standards, the ISO 14000 EMS standards are being adopted by companies and governments worldwide. The United States and Canada have well-established programs. In Europe, countries differ but are firmly committed toward environmental-management standards (BS 7750, EMAS and ISO 14000). The Department of Environmental Protec¬tion of the State of Pennsylvania is using ISO 14000 as a vehicle to develop a closer working relationship with industry, and it is anticipated that this policy will eventually lead to fewer environmental site inspections for those companies with ISO 14001 certification. The Depart-

Jan 1, 1999

By Gilbert M. Farrior

The electrical resistivity the coefficient of electrical resistivity the Hall coefficient, and the absolute thermoelectric power were determined in this Bureau of Mines investigation for nine compositions of the TiB2-CrB2 sub-system. The numerical values of the electrical resistivity and the thermo-electric power were greater for the intermediate compositions than for the end members. The absolute values of the Hall coefficients and the coefficients of electrical resistivity were less for the intermediate compositions than for the end members. The electrical resistivities and Hall coefficients were about the order of magnitude of most metals--from 34 to 202 microhm-cm and from about 0 to -23.3 X 10-4 cuP/coulomb. The thermoelectric power was somewhat greater than that of most metals--up to 15.6 microvolts per 0 C.

Jan 1, 1965

By T Baumgartl, C Gonzales, A Soliman, M Edraki

A soil cover isolates potentially acid-forming (PAF) mine wastes from atmospheric interaction and thereby mitigates acid mine drainage. As a cover that comprises either a single layer or a composite barrier, it essentially manages percolating rain water from flowing into these PAF materials and minimises air flow as oxygen has low diffusivity in saturated soils. However, the availability of suitable soils as cover materials is limited, especially in arid and semi-arid regions where weathering rates are low.This paper investigates the potential use of mine wastes as cover materials in a water-shedding soil cover in north-west Queensland. Four cover trial plots were built using mine wastes as cover materials. Each 2.3 m cover trial plot consisted of a 1.5 m soil cover made up of waste rocks and fines, a 0.5 m drainage layer that consisted of 0.1 m waste rock aggregates and a base layer made up of blended mine tailings. The hydrologic properties of cover materials were determined by in situ measurements and laboratory experiments, which, in turn, were used as input in a numerical model that described the cover’s transient soil moisture profile. The successful performance of the cover is reliant on the long-term stable geochemical behaviour of the substrate used as cover material. Therefore, investigations were carried out to determine the geochemical properties of the cover materials constructed from benign waste rock using static and kinetic tests, with the objective to increase the level of certainty of the material’s benign characteristics. Consequently, the long-term performance of this water-shedding cover design is described in terms of the physico-chemical characteristics of its outflows.CITATION:Gonzales, C, Baumgartl, T, Edraki, M and Soliman, A, ?2014. Mine wastes as cover materials in a water-shedding soil cover in north-west Queensland, in Proceedings Life-of-Mine 2014 , pp 261–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By Harry J. Evans

DURING the fury of the conflict it was believed quite generally that World War II was being fought for and would accomplish a permanent peace. Yet, before the guns were actually stilled on all fronts, the American people realized that the devastated world would continue to be dominated by suspicion and uncertainty. The misunderstandings which rapidly developed indicated that it may prove unwise to rely wholly on mutual international agreements and contracts to avoid war. Before the celebrations of V-Day died down serious thought was being given toward measures for preparedness for the next conflict. Along with a realization of the enormous loss of life caused by the destructive forces of war, the American people came to understand the seriousness of the rapid and unwarranted depletion of our natural resources. During the last half of 1945 the question of stock-piling strategic and critical raw materials for a future national emergency became an intensely live subject.

Jan 1, 1946

By W. G. Prast

The role of governments as a factor in the international non-metallic minerals industry can take several forms. Classically, the government acts as a taxing agent, collecting part of the economic rent on behalf of the country from private-sector mine operators. In addition to its taxation policies, the state can and does provide the practical commercial framework of regulatory and fiscal incentives and restraints that shape the activities of the mining firms. In addition to its functions as an agent of the public interest, the government can choose to take a more direct stake in the mining industry, and has done so in the instance of several industrial minerals that are actively traded on world markets. In this paper, the actions of three governments are reviewed and the consequences of their actions are examined.

Jan 1, 1981

By John C. Nigro

Bench scale and pilot plant research was conducted using dolomites (CaO,MgO) lime as the basic additive in the preparation of self-fluxed pellets from a typical magnetic taconite concentrate (5.57 S_2). The specific objective of this investigation was to ascertain the viability of the magnesia lime pellets in high temperature oxidizing and reducing atmospheres. Pellet basicity and induration temperature were major parameters affecting fired pellet quality; temperatures ranging from 1,200° to 1,250" C appeared to be the most favorable for production of self-fluxed pellets with basesities (B) above 1.0. Comparison of the mechani¬cal and metallurgical properties of regular (acid) and self-fluxed pellets (B 1.55) produced under similar conditions in a modified grate pelletizing machine showed that the self-fluxed pellets were more resistant to abrasion and to high and low temperature reduction disintegration, an important consideration in commercial application. The Plus 3 mesh Linder index increased from 68 percent (regular pellets) to over 90 percent (self-fluxed pellets). The reducibility and swelling indices of the self-fluxed pellets were found to be comparable to the regular pellets.

Jan 1, 1972

By Weijie Wei, Jinwang Zhang, Jiachen Wang, Yang Li

"Longwall top-coal caving (LTCC) mining technique is one of the important methods for underground thick seam extraction in China. The coal seam in LTCC panel is divided into two parts: bottom-coal and top-coal. The bottom-coal is mined by conventional longwall method while the top-coal is mined by caving method. The top-coal caving process in LTCC and block caving process in metal mine are both gravity flow of loose ore/coal blocks. However, the presence of caving shield in LTCC makes the characteristics of drawing body shape in the two caving processes differ a lot. This paper discusses the influence of caving shields on the characteristics of drawing body shapes in light of recent studies of the top-coal drawing process. The theoretical model for describing the drawing body shape in LTCC is proposed both along the seam strike and seam inclination. Then, the experimental data are used to validate the correctness of the theoretical model. Furthermore, two examples of how the theoretical findings assist LTCC mining are given and discussed.INTRODUCTIONLongwall top-coal caving (LTCC) mining technique and large-cutting-height mining technique have been widely used for extracting thick coal seams in China. About 0.6–0.7 billion metric tons of coal come from longwall top-coal caving panels every year. The maximum annual production is 15 million metric tons per panel _The mining method employed in such panel is a combination of top-coal caving mining technique and large-cutting-height mining technique, which is suitable for seam height between 12–20 m, as shown in Figure 1. Apart from China, LTCC has also been employed in some coal mines in Australia and Vietnam (Le et al., 2017).The coal seam in a LTCC panel is divided into two parts: bottom coal and top coal. The bottom-coal is mined by the conventional longwall method, while the top coal is mined by the caving method. The top-coal caving process in LTCC and block caving process in metal mines are both gravity flows of loose coal/ore blocks, as shown in Figure 2. However, the presence of caving shields in LTCC causes the characteristics of the drawing body shapes in the two caving processes to differ significantly.There are two main differences between the blocking method and the top-coal caving method:"

Jan 1, 2019

By E. P. Youngman

The basic mining law of Netherland India is contained in N. I. Statute 1899 , No. 214 , as amended by N. I. Statute 1910 , No. 588 , and 1919 , No. 4 , which is quoted as the " Indian Mining Law, " the effective date of which was fixed as May 8 , 1907 , by proclamation dated October 12 , 1906. The Indian Mining Law was supplemented by Ordinance No. 38 , of 1930 , which was passed by the Volksraad on March 18 , 1930 , to become effective on October 1 , 1930 ( superseding an earlier ordinance entitled " Government Gazette , " 1906 , No. 434) . An important law with respect to American petroleum rights , Statute No. 23 , passed February 9 , 1928 , approving contracts between the Indian Government and the Netherland subsidiary of a large American oil company , is in the nature of a private law or of an enabling act ( see section of this paper entitled " Rights of Foreigners" ) . Statute 1930 , No. 348 , effective October 1 , 1930 , sets forth in minute detail conditions under which prospecting and mining permits may be granted. Statute 1930 , No. 341 , effective October 1 , 1930 , embodies the police regulations of the mining industry.

Jun 1, 1931

By Brian Putland

Single stage semi-autogenous / autogenous (S/AG) milling has become a common design for a variety of ore types with the advantages of being comparatively low capital cost and flexible for future expansion. The single stage SAG/AG milling option is ideal for starter projects with significant exploration and expansion potential. Currently a number of the largest SAG mills designed are installed in single stage configuration. This paper discusses the challenges associated with the process design of single stage SAG/AG milling circuits, the design flexibility required to ensure a robust circuit and the operating techniques adopted at successful installations.

Jan 1, 2012

By R. D. Rosenkranz

The Bureau of Mines has investigated the availability of copper from 272 deposits in market economy countries. The deposits studied have demonstrated resources totaling 413 million metric tons of contained copper and account for more than 90 pct of the reserve base for market economy countries. Using data gathered as part of its Minerals Availability Program, the Bureau performed geologic, engineering, and economic evaluations in order to determine the copper production potential of each deposit. At the 1981 copper market price of $0.85/lb, the deposits studied could economically produce an estimated 88 million metric tons of copper (allowing for profit computed at a 15-pct rate of return), primarily from mines operating at the time of the study (1981). At this price, producing mines in market economy countries could economically produce only 2.1 million metric tons of refined copper per year. However, actual 1981 production was 6.2 million metric tons, indicating that many mines continued to operate even though they were unable to cover all production costs. For U.S. producing mines, the estimated average cost of production per pound (including profit at a 15-pct rate of return) was $0.15 higher than the average cost in other market economy countries.

Jan 1, 1983

By B. J. Scheiner

The presence of organic materials in gold ores cyanidation. The presence of organic materials interferes with gold extraction by The carbon contained in the ore has been shown to adsorb gold cyanide complex from solution. Removal of the carbon content by roasting or chemical oxidation prior to cyanidation results in gold extractions of 85 to 95 pct. This paper by the Bureau of Mines, U.S. Department of the Interior, discusses how the mineralogy of the carbonaceous gold ores affects gold recovery by cyanidation. It also discusses the advantages and disadvantages of roasting and chemical treatment to render the ore amenable to cyanidation.

Jan 1, 1987

By H. Yoshida

Jet grouting was first introduced in Japan in the second half of the 1960s, approaching 50 years ago. By the end of the first 40 years, jet grouting from single to triple fluid systems had become a global technology. In the last ten years, progress in the jetting has been remarkable, and operational efficiency has improved. The quantity of carbon dioxide emitted in unit soil improvement has become one-third that of the initial technology. Meanwhile, technologies in waste recycling and horizontal jet grouting are also emerging. This paper discusses developments in the most recent ten years.

Jan 1, 2010

By J. K. Armstrong, C. Feyerabend

"As mines are constantly growing and expanding, so do the challenges for emergency response teams. They have to keep up with the pace set by current and future production techniques. Although mines have now reached depths of several kilometres and their dimensions and complexity are that of an entire city, mines rescue still must be able to reach the most remote areas within the mine in a swift and safe manner. The duration of breathing apparatus and physical human capabilities are limitations. Therefore, alternative methods have to be explored to extend the time under oxygen for mine rescue teams without putting additional stress on the team members. To address this global trend, Dräger, Goldcorp and PAUS have partnered to develop a mine rescue vehicle that allows mine rescue teams to travel for an extended period of time through a contaminated atmosphere without the use of breathing apparatus, thus extending the range of their mission. By applying currently available techniques, the safe expansion of mine production can be ensured, giving mine rescue teams the ability to respond to accidents in a safer and faster way. INTRODUCTION With the reduction of easily accessible natural resources, there is a global trend toward searching for higher ore grades underground and/or continually expanding mines underground to extend their lifetime. While in some areas this trend has just begun, in other countries mines are reaching depths or horizontal dimensions that pose extreme challenges (Codelco, 2016). These challenges include safety relevant topics, such as rock stability, heat and seismicity, but also more basic issues such as distances to the working face, which can become crucial considering the cost to develop a new shaft or decline. To overcome this, there is a growing interest in collaboration among various stakeholders to drive the development and support of deeper mines and tackle the complexity of underground mining. This is evidenced by the fact that several industry and research groups and networks have formed, e.g. the I2mine project in Europe and the Ultra-Deep Mining Network by the Centre for Excellence in Mining Innovation in Canada. Due to commodity pricing and the trend toward renewable energy, metal/non-metal mining will be the driving force behind this development."

Jan 1, 2019

By R. Larry Grayson, Joel R. Warneke

The mining industry has searched for a message that will resonate with the public while focusing on the industry’s positive contributions to society. So far, environmental groups remain unconvinced and the public is still largely uninformed. In the authors’ opinion, a number of recent events and experiences have converged to help shape a more effective public communication on mining’s important role. This article presents a perspective on coal’s role in sustaining society by anchoring the message in a transparent way, including a material flow analysis, that links coal’s impacts across a range of social and environmental aspects. Past and continuing image problems In her 1994 paper, Nancy Bingham, with Caterpillar, outlined what the public thought about mining. Based on extensive interviews, the following results were found: • The public believed mining harms the environment. • The public believed mining harms people in nearby communities. • The public believed mining exploits workers. • The public believed mining has little personal benefit to the individual.

Jan 1, 2006

By J. B. Macelwane

Geophysics differs from geology and physics in in many respects. In the first place, geophysics is a complex science embracing the fields of seismology, geomagnetism, geoelectricity, geodesy, meteorology, vol-canology, physical oceanography, physical hydrology, tectonophysics and exploration geophysics. Geology is also a complex science and so extensive in its various fields that no one can master them all, and no part of geology deals in any sense with several of these fields of geophysics. In the second place, geophysics makes use of methods and instruments that are derived primarily from the science of physics. Geology, on the other hand, has methods of its own and it draws its borrowed techniques and its instrumental equipment not only from physics but also and perhaps primarily from chemistry and biology. The difference, therefore, between the geophysicist and the geologist lies partly in the phenomena that are observed, partly in the methods and instruments with which each carries on his exploration; but partly also, and perhaps principally, in the habitual attitude of mind and in the background of specialized training with which each approaches the problems presented by this planet of ours. The geologist as such, therefore, is no geophysicist. On the other hand, the physicist is not a geophysicist either. Isolation of each problem in a closed laboratow system under complete control is fundamental to the methods of the physicist. The geophysicist must apply physical instruments and physicomathematical reasoning to the study of physical quantities in their undisturbed natural environment. What, then, is a geophysicist? In the sense that he is a trained expert in all of the geophysical sciences, I do not believe that such a person ever existed. It would be beyond the possibilities of a single lifetime. I think there is confusion in our ideas and in our use of terms. We are not all thinking of the same thing when we say geophysics or geophysicist; yet we seem to talk as though we were. It is as absurd to say that the whole of geophysics belongs to geology because the field of a particular type of geophysicist—the exploration geophysicist —calls for some knowledge of geology as it would be to say that the whole of biology belongs to geology because a particular type of biologist—the paleontologist— needs some knowledge of geology. Development of a Geophysicist Since it is impossible to become an expert in all the fields of geophysics, and since students entering college seldom know the field they will choose as a career, what would we suggest as the best general preparation for work in geophysics, whether as a meteorologist, an oceanographer, a seismologist, a geodesist, a geomagneticist, a volcanologist, a tectonophysicist, a hydro1 ogist, or an exploration geophysicistp we may distinguish five phases in the development of a geophysicist: (I) his mathematical and scientific studies in high school; (2) the general mathematical and scientific

Jan 1, 1946