Search Documents

By S Hapugoda, J Manuel, E Donskoi, L Lu

Sinter can constitute up to 80–85 per cent of the total ferrous burden in modern blast furnace ironmaking operations. The mineralogy and microstructure of iron ore sinter play an important role in determining its physical and metallurgical properties. As a result, characterisation of sinter phases is a cost-effective and complementary tool to conventional physical and metallurgical testing of iron ore sinter in evaluating and predicting sinter quality. Over the years, CSIRO has developed a scheme for characterising iron ore sinter that classifies primary sinter phases such as unreacted and partially reacted hematite and magnetite, and secondary phases, including prismatic high-temperature silico-ferrite of calcium and alumina (SFCA), microplaty SFCA (SFCA 1), dense SFCA, secondary hematite and magnetite, glass, larnite (dicalcium silicate; Ca2SiO4) and remnant fluxes. Quantification of these phases has traditionally been carried out by manual point counting under a petrographic microscope; however, new technologies based on automated optical image analysis, quantitative X-ray diffraction and scanning electron microscopy are now available for evaluation. In this study, two sinter samples of varying chemistry were prepared and characterised using both point counting and automated optical image analysis. The implication of the results obtained for the performance of different quantification methods is also assessed.CITATION:Hapugoda, S, Lu, L, Donskoi, E and Manuel, J, 2015. Mineralogical quantification of iron ore sinter, in Proceedings Iron Ore 2015, pp 35–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Theodore H. Budd, Austin M. Cooney

The North Shore 9 Collector System comprised an integral part of the Milwaukee Metropolitan Sewer District's Water Pollution Abatement Program. The project required the construction of 1,490 m of tunnel, ranging from 1.5 m to 4.6 m in diameter along three separate alignments beneath arterial streets traversing Milwaukee's central business and cultural districts. This paper details the various aspects of the tunnel drives which were accomplished using two Lovat EPB type TBMs in conjunction with pipe-jacking procedures. Shaft configurations developed for the project, including ancillary subsidence mitigation components and portal pressurization facilities are discussed. Anomalies in observed soil behavior at variance with the parameters delineated in the project's geotechnical report are addressed.

Jan 1, 1993

By Theodore H. Budd, Austin M. Cooney

The North Shore 9 Collector System comprised an integral part of the Milwaukee Metropolitan Sewer District's Water Pollution Abatement Program. The project required the construction of 1,490 m of tunnel, ranging from 1.5 m to 4.6 m in diameter along three separate alignments beneath arterial streets traversing Milwaukee's central business and cultural districts. This paper details the various aspects of the tunnel drives which were accomplished using two Lovat EPB type TBMs in conjunction with pipe-jacking procedures. Shaft configurations developed for the project, including ancillary subsidence mitigation components and portal pressurization facilities are discussed. Anomalies in observed soil behavior at variance with the parameters delineated in the project's geotechnical report are addressed.

Jan 1, 1991

By G. K. Mann

Fragmentation analysis of blast or crushed rock material is a time-consuming and costly process. During the last two decades, the mining industry has been investigating image-based analysis systems as an alternative to generate fragmentation results. Many image-based techniques and commercial products have emerged during the last few years, and the mining industry has recently begun using these tools for real-time estimation of size distributions. Some existing systems require manual image editing to add or delete edges (or net) before executing the fragmentation analysis routine. This manual procedure may take hours of time for each image analyzed. Reliable and robust image segmentation should be able to handle a wide range of rock textures and sizes under a variety of lighting conditions. This paper describes a novel software application, which has the capability to autonomously capture images and analyze them to generate the particle size distribution. The system can also process a batch of images captured during a fixed duration of time and produce the overall particle size distribution. The new method has different layers of segmentation modules, which allows the system to operate under a wide range of rock textures and lighting conditions. A new grey-level slicing technique is developed which can perform under a range of illuminating conditions. The Canny-based edge detection technique is used to segment rocks appearing in dark regions.

Jan 1, 2006

By Dan Eyde

Low levels of thallium were detected in the mine water drainages, and process water discharges of western mining and smelting operations. This required remediation under state regulatory standards, which allow discharges of no more than .0017 ppm thallium in mine water discharges. Influent streams containing thallium can be mitigated to state discharge standards after a single pass through the series of fluidized upflow columns. Test work to determine the optimal flow rates used pilot scale systems at two separate locations treating 5 - 25 gpm of effluent. The test system at the gold mine mimics the full-scale system, which will be based on the existing upflow carbon tanks that have been converted to zeolite columns. The system installed at ASARCO's East Helena smelter has a far more complex influent stream with a high loading of competing cations. Nevertheless the columns filled with CABSORB® are successfully mitigating the thallium contamination. CABSORB® ZS500RW is a product based on the sodium analog of the zeolite mineral chabazite named herschelite.

Jan 1, 1998

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Kellie Provazi

"The purpose of this paper is to study metal separation and recovery from a sample composed of a mixture of the spent household batteries main types, using liquid-liquid extraction and metals electroplating. The electrolytes preparation consisted: grinding the waste of mixed batteries, reduction and volatile metals elimination using electric furnace and acid leaching. From this solution were studied the liquid-liquid extraction using Cyanex 272 [bis(2,4,4-trimethylpentyl) phosphoric acid] with tributyl phosphate as extracting agent. After study of solvent extraction and stripping has been recover and separate the metallic ions and with electroplating was recovered the manganese, copper, nickel and cobalt in their metallic forms.IntroductionCurrently has increased the consumption of electronics devices such as mobile phones, laptops, wireless phones, comcorders, etc., especially portable devices that use batteries as a power source, and consequently has increased the disposal of such material.Increased consumption of this devices is caused by several factors including increased popularity of consumer electronics devices, has become essential of modem life. Therefore, recycling of batteries is important because its reduces the waste of raw materias and nonrenewable resouces used in manufacturing these materias and help prevent potential environmental risks associated with improper disposal of these products together with household garbage.The batteries have a very diverse composition, containing metals such as zinc, lithium, nickel, lead, mercury, cobalt, cadmium, iron, copper, manganese and rare earths. Some components may contain hazardous materials such as cadmium, mercury and lead, and can contain acids or bases.This research line is a pioneer in dealing with a single process for recycling a mixture with all batteries types, for only processes that exist in the world are based on the recycling a mixture with all types of batteries, for only processes that exist in the world are based on the recycling of one or two types of batteries [1-4]. This process necessitates the previous separation of the batteries by type."

Jan 1, 2012

By W. D. BRENNAN

AS a rule the thoughts of engineers are more often directed toward the mechanical and physical conditions of mining practice than they are toward the disposition and the marketing of the product. This, I think, has been true of the coal industry to the present time not only among the engineering force but also generally true of operators. There has been a tendency to place the sales department in a rather secondary position; for a great many years there was a greater demand for coal than the supply would meet, so it was only necessary to increase production: either by expansion of operating mines, or opening new mines of greater capacity. While the production of coal is still a highly important phase of the industry, its enormous development throughout the country, the great advance in fuel, efficiency and economy, and the discovery of new reserves of competitive fuels have combined to create a buyers' market and force the present-day attention upon merchandising in modern ways. A buyers' market has a natural tendency to develop the keenest competition, frequently unscrupulous and nearly always profit-wrecking. Under such conditions bad practices are bound to grow and to extend until the industry is wrecked, or until wiser heads get together to reduce or eliminate unfair methods of competition. This is not so recent a condition as one might believe.

Jan 1, 1931

The mining industry has been slow at adopting the latest management philosophies from other industry sectors, such as manufacturing, and in retrospect, with good cause. With the plethora of three-letter-acronyms such as TQM, JIT, TPM and now, BPR each touted as the panacea for profit improvement, you wonder if you must choose one or attempt to embrace them all! In truth, each new insight into organisational behaviour bears some investigation. This paper looks at the underlying principles and elements of successful change strategies, and how several mining companies, including coal mines, in Australia, Chile and Canada, are applying these principles to their operations. These examples illustrate the need to think radically, and to view mining as an overall process delivering value to the customer rather than a collection of functional silos. They also show that often, a continuous improvement initiative is not enough when a fundamental redesign, a paradigm shift, is needed for a performance breakthrough.

Jan 1, 1998

By Visitor Makiyi, Chris Batten

Poor coal recovery due to coal damage or loss caused by blasting can have a significant impact on a mining operation. Increasing coal recovery by reducing blast damage can provide a significant opportunity for coal mines to maximise their revenue and reduce their operating costs. This paper provides details on advanced drilling and blasting techniques used throughout the coal industry globally to prevent coal damage and movement during blasting. Typical coal loss and damage mechanisms are explained, along with how each of the applied techniques works to minimise the impact of each mechanism. Key requirements for a coal loss reduction program are detailed with typical design parameters used for each of the methods discussed. The positives and negatives of each method are also provided to enable comparisons and help determine suitability for a particular coal mining operation.

Jan 21, 2025

By Yoginder Paul Chugh, Jason E. Tinsley

"Over the last five years, the authors have compiled a database of Short Encapsulation Pull Test (SEPT) evaluations from Interior Basin (Basin) coal mines. Typically, SEPT data are analyzed to obtain peak load carrying capacity per unit length of resin encapsulation designated as the ""Grip Factor,"" or GF. In a previous paper, ""An Analysis of Short Encapsulation Bolt Pull Test (SEPT) Data From Interior Basin Coal Mines,"" authors analyzed tangent value of the load-displacement curve as Anchorage Stiffness at 50% (AS-50) of the peak load, or GF value, to assess reinforcement potential of an installed bolt system. This paper attempts to correlate the secant AS VALUES (of SEPT on 6 ft (1.8 m) long installed bolts at a lower load of about four tons from several different mines in the Basin with their MSHA-approved primary support requirements. Since the current regulatory environment requires plan changes dynamically to ensure that roof falls are minimized, the authors hypothesize that the practiced roof control plan must meet the minimum requirement of adequately supporting immediate roof strata. The analyses are based on 181 SEPT studies performed by Minova professionals. Analyses indicate a macrolevel correlation for both roof support density and roof support cost that may have the potential to be used by mine operators to compare their performance with other mines in the area. Limitations of the analyses include ignoring mining depth, mining height and required secondary supports as part of the requirements for a roof control plan. The authors recommend additional analyses to develop this concept further to develop guidelines that can be confidently used by coal companies.INTRODUCTIONPartially- and fully-grouted bolts are extensively used in coal mines for roof support as part of MSHA-approved roof control plans. Since grouted bolts have a larger area of contact with the rock, they can develop much greater anchorage capacity than conventional expansion shell (point-anchored) bolts. Load transfer characteristics and interaction mechanics between steel rebar, grout and rock mass around the bolt hole for grouted bolts are generally assessed in the laboratory or field though short-encapsulation pull tests (SEPT), which have been extensively researched by Aziz and Jalalifar (2005), Aziz (2004a), Serbousek and Signer (1987), Signer (1990), and Mark et al. (2002), among others. In a SEPT, about 12 in. (30 cm) of bolt length is typically encapsulated in resin and a pull test is performed to collect load-displacement data prior to failure and, in some cases, post-failure. A typical load-displacement data set for a bolt is shown in Figure 1. SEPT characteristics are designated by peak load carrying capacity, or grip factor, which is the peak load carrying capacity per unit length of resin encapsulation. SEPT is routinely used to assess anchorage performance characteristics of different lithologies overlying a coal seam to identify type of bolt, bolt diameter, length and spacing across and along an excavation. Anchorage stiffness, or AS, at any load may also be calculated as the tangent or secant value of the slope of the load displacement curve at a particular load level. Anchorage Stiffness characteristics of bolts from SEPT data have typically not been considered in any depth until recently (Chugh et al., 2014; Chugh et al., 2015)."

Jan 1, 2016

By P. Hr?enjak

Two groups of methods are usually used in design procedures of underground excavation of dimension stone: the analytical and numerical methods of analysis. In all of these methods the in situ rock mass strength represents the main problem. This is due to massive rocks in dimension stone deposits, consisting of large blocks of rock separated with particular discontinuities, for which the Hoek-Brown empirical criterion, developed for jointed rock masses, cannot be realistically used to estimate rock mass strength, especially for a particular block of rock mass or a particular pillar. On the basis of the regular underground excavation process of dimension stone by separating blocks with the flat jack application, we developed the in situ flexural strength testing method. We carried out numerical analyses and evaluation of uncertainty of measurement in order to validate the in situ flexural strength testing method. On the basis of very good validation results, as well as results of the in situ flexural strength testing of exploitable layers on the ?Kanfanar? quarry, we introduced a new coefficient of reduction, which can be used for correction of other strength parameters determined by laboratory testing for obtaining a realistic value of rock mass strength.

Aug 1, 2013

By E McLean

The decision making check-list and hierarchy of information for process and plant design is generally wide-ranging and complex. The nature of grades, mineralisation and ore types in an ore body, its mine development sequence, and the body of results from metallurgical and physical test work present complex and competing influences on flowsheet development, values for design, equipment selection, plant efficiencies and operating strategy. The challenge is how to manage all these variables, to understand their impacts on performance, and how best to provide a cost-effective plant design and robust process that meets daily/weekly/monthly operating objectives. Throughput, production and grade or product specifications need to be met. The ore body is not average; its range of metallurgical and physical characteristics may be moderately to highly variable. This paper assesses some of the key competing influences and conflicting issues in design and equipment selection, and their effect on production and performance expectations.

Aug 8, 2011

By M. Ghiani, P. Carbini, R. Ciccu, C. Del Fà

"This paper is concerned with the problems inherent in the efficient and economical processing of the fine fractions of a coal from the Sulcis basin (Sardinia, Italy) whose characteristics are typical of low-rank coals occurring in the Mediterranean region. Three different techniques, based upon surface properties, are examined. Flotation can be very efficient from both a technical and economic point of view, provided care is taken in the modulation of the flotation pulp. Interesting results have been obtained with oil agglomeration and this method could be economically feasible. Finally, electrical separation has proven a viable technique, although it entails preliminary drying.Besides discussing the problems encountered in the experimental research, some significant results of general validity are also given. They demonstrate that cleaned products can be obtained with fairly interesting recoveries, thus opening the way to advanced research aimed at setting up the most suitable technique for industrial application. IntroductionAs a result of the oil crisis, which caused a major upset in world energy supplies, the last ten years have seen a revolution in the energy policies adopted.In particular, the status of coal, which seemed destined to decline in view of the availability of liquid fuel, has had to be re-examined. The need to meet energy demands under improved reliability conditions and controlled prices through a broader and more flexible diversification of sources of supply has evoked, especially in highly industrialized countries, a renewed interest in coal. The result has been a consistent increase in demand and production as well as investments in new mines and the reinforcement of the infrastructure.This turn of events has also lead to a re-evaluation of young low-rank coals, hitherto considered uneconomical and thus neglected, because of their low heat value. In fact these coals, which have a high ash content, may also be relatively highly contaminated with sulphur. The above drawbacks, which still today preclude the widespread use of these coals, are bound to create even greater problems in the future as increasingly restrictive environmental control imposes, without exception, recourse to cleaner fuels."

Jan 1, 1986

By I. Raposo, I. Moreno-Ventas, A. Palma, M. J. Díaz, M. Vázquez

The oxidative degradation kinetics of chalcopyrite have been studied by thermogravimetric analysis (TGA). The obtained data are necessary for the kinetic description of the flash fusion process, which can contribute to the optimization of the smelting process in copper extractive metallurgy. Activation energy (Ea) evolutions of the involved processes have been determined by several isoconversional methods; in this sense, the chalcopyrite oxidation processes could be adequately described, among studied models (E1641–16, Ozawa–Flynn–Wall, Kissinger–Akahira–Sunose and Friedman), by the Kissinger–Akahira– Sunose kinetic model. Using this method, Ea and A values are found to be very dependent on the conversion. Under lower conversion levels, higher Ea and A values have been calculated with respect to that found for medium and higher conversion levels.

By Leandro de Arruda Santos, Lorena Isabela de Oliveira Ribeiro, Jéssica Dornelas Silva, Pedro Damas Resende, João Victor Lucas Amim, Suzanny Cristina Soares Martins, Vicente Tadeu Lopes Buono

O objetivo do presente estudo foi avaliar a resistência à fadiga de duas ligas de NiTi diferentes sob condições de teste controladas por deformação a 25°C por meio de testes de fadiga por flexão rotativa. Além disso, as propriedades mecânicas, térmicas e estruturais dos fios foram caracterizadas por ensaios de DSC, DRX, MEV/EDS e tração. Os resultados revelaram que ambos os materiais são superelásticos à temperatura ambiente e, portanto apresentaram composição basicamente austenítica de sua matriz. Os resultados de ensaio de tração são condizentes com a caracterização térmica e estrutural, pois os materiais apresentam recuperação total de forma após ciclos de carga e descarga em tração. Ambos os materiais são ricos em titânio, um deles apresenta camada de óxido superficial enquanto o outro apresenta acabamento superficial. Apesar das propriedades similares a amostra 1 apresentou média de 77 ciclos até a falha, enquanto a amostra 2 resistiu a 1827 ciclos..

Oct 25, 2019

By Normand Champigny

The Forces of Change ? The current business environment ? What can we expect for the future on management of physical assets ? The impact of maintenance on production costs ? What is RCM is doing is improving business performance ? The beginnings of RCM The RCM II Process ? RCM II is a structured process that involves employees in determining the best failure management tactics for systems and equipment in their operating context ? The method is an effective approach to risk and cost reduction as well as failure management

May 1, 2002

In recent years there have been many changes in mine ownership due to the on-going rationalisation towards larger mining companies. Larger companies inevitably find it hard to manage small mining operations and in many cases smaller mines do not fit corporate resource, production and profit criteria. Smaller companies are more suited to managing these medium or small scale mines and are tendering for the purchase or lease of mines that larger companies wish to dispose of. In addition to these factors there has also been a trend (especially in Western Australia) for mines to continue operating at ever increasing depths. This in turn has led to more mines operating in high stress environments and experiencing damaging seismicity. Assessing the viability of seismically active mines from a takeover or purchase point of view should involve analysing the risk profile of every aspect on mining that could be affected by adverse seismicity. This includes assessing current and alternative mining methods, mine designs, support systems, extraction sequencing, monitoring and blasting. This paper includes discussion on items that need to be assessed when considering the purchase of seismically active mines, with experience gained from some recent studies in Western Australia. In these cases it was apparent that quantification of previous seismic history on itÆs own was a totally inadequate method of assessing minewide seismic risk potential. A more holistic approach is required, taking into account all aspects of relevant data, all the minewide effects of seismic activity and all possible means of mitigating those effects.

Jan 1, 2002

By W. G. Davenport

Chapters 7,8and 9 calculated three combinations of: blast composition (mass% O2, mass% N2) oil quantity per tonne of concentrate blast temperature that will steadily produce molten 65% Cu matte from pure chalcopyrite-concentrate. The combinations are:

Jan 1, 2001

By William Gleason

The Society for Mining Metallurgy and Exploration (SME) has a long and proud history of being the world?s leading resource for the dissemination for technical information regarding the fields of mining and mineral extraction and processing. That reputation was met, and maybe even exceeded, with the programming for the Society?s 2014 Annual Meeting in Salt Lake City, UT Feb. 23-26. The meeting drew more than 6,700 attendees to the three-day conference that featured more than 90 technical sessions with 670 presentations. These sessions covered the breadth of the mining and minerals industry, but it was the so-called ?softer issues? that were discussed in the keynote session that kicked off the meeting. The keynote session, ?Community Engagement: Building Partnerships for Mining,? brought together some of the leading voices from the mining industry, as well as some of the top voices from nongovernmental organizations (NGOs) that work in the mining sector. The common ground between the panelists was their dedication to working to ensure a social, economic and environmental balance in the development of mines. ?We wanted to bring these NGOs in to begin a dialogue to see how we can work together,? said SME President Jessica Kogel. ?This is a space that SME has not typically operated in, but one in which SME can bring a technical, scientific voice to the discussion. SME wants to play a leadership role in creating partnerships between the technical, social and economic areas that are crucial to the success of any mining project.? In today?s environment, finding mineral deposits and extracting the minerals in an economically viable manner is just one piece of an increasingly complex puzzle. Earning and maintaining a social license to operate requires careful consideration of local and global impacts. The industry often comes under intense scrutiny when a new project is proposed and, therefore, it must strive to meet the highest ethical and environmental standards. Success requires cooperation and collaboration between the industry, community and NGOs.

By John W. White

Anthracite mine refuse, or culm dump material as it is sometimes called, is the waste material resulting from the sizing and cleaning of run-of-mine deep and strip-mined anthracite coal. It may also contain mine rock, carbonaceous shale, pyrite, and other debris from mining operations. This material is generally stored in piles or banks, some of which are over 100 years old. Many of the older banks contain a considerable amount of good coal, particularly in the finer size ranges, since these sizes did not have any particular economic value in the early days of anthracite mining. Today, the refuse material from a cleaning operation must be piled in an orderly fashion and in such a way as to minimize the tendency to ignite. There are well over 400 of these banks in the anthracite region containing over 1100 million tons of refuse located in the north-eastern part of Pennsylvania. The banks range in size from a few thousand tons of material up to as much as 13 million tons. Most of

Jan 1, 1972