Search Documents

By Masakazu Iida

In this article, technologies of unburned Al2O3-MgO (UAM) refractories are demonstrated in terms of microstructure evolution. During operation, Mg2+ diffuses from MgO to Al2O3 through the liquid phase to form spinel (MgAl2O4) network. Molten slag tends to penetrate along the voids in the spinel network structure and spinel dissolves in the penetrated slag. Therefore, maintaining a high degree of spinel saturation in the penetrated molten slag is important. In order to achieve the condition described above, suppression of overall mass transfer through penetrated slag is effective. This is achievable by evolution of complicated spinel network structure with small pore diameter, which increases the flow resistance of molten slag. Thus, optimization of refractory composition and fabricating conditions, with the aim of creating on improved spinel network, is essential. The effectiveness of spinel network improvement was validated by commercial applications. According to the investigation of UAM brick after use, further densification due to heating under restrained conditions was recognized. Hence, it was concluded that the evolution of the spinel network structure in UAM refractories is essential technology needed to improve durability.

Oct 30, 2017

By B Flynn, P Knights

Low-loaders or 'floats' for relocating equipment in surface mines are limited to a capacity of approximately 350 t. In the iron ore industry it is desirable to be able to rapidly relocate excavators in order to maintain production rates within appropriate quality limits. In addition, the ability to rapidly relocate heavy equipment raises the possibility of improving the quality of repairs by performing maintenance in controlled shop conditions. However, many iron ore operations operate hydraulic excavators in the 600 to 800 t range, with newly released excavator models exceeding 800 t. These excavators are too large to float using conventional technology. This paper examines the potential for using multi-bogie transporters to relocate large hydraulic excavators in surface mines. Recent innovations have seen the development of modular transporters which can be coupled together to achieve larger platform areas. When separated, and with their drive bogies neutralised, these units are able to be towed behind prime movers and relocated between mines via public roads. The potential cost savings for relocating a Terex RH170 excavator in an open pit coal mine are examined. In the first six months of 2008, the analysis showed the potential for a 38 per cent reduction in total travel time with a corresponding revenue increase of approximately $350 k. The paper recommends that a feasibility study be conducted into offering a heavy equipment relocation service within the Pilbara region.

Jan 1, 2009

By S. J. Jung

In recent years, the use of shotcrete, a practice familiar to the mining industry, has been on the increase. This research has come about because of the recognized need for a safe, easy way to line small diameter bored raises (less then 150cm). Up until now, an operator has gone down the raise and applied the concrete lining manually, using the shotcrete method of application. With an automated system, there would be no man positioned in the bore itself. All control functions could be commanded from a central location. Shotcreting in the confined space of a small diameter bored raise presents problems that can be overcome by the application of shotcrete using a remote system.

Jan 1, 1994

By L. L. McDaniel

Copper smelters of various kinds have operated in the Morenci district since 1872, but all have been abandoned with the exception of the present Morenci Smelter of Phelps Dodge Corporation, which was completed in 1942. During the five-year period starting in 1937, the Morenci ore body was prepared for open pit mining, pilot mill test work was carried out, and a complete reduction works, of which the Smelter is a part, was designed and erected. Actual construction work on the Morenci Smelter was started in the fall of 1940, and warming up of the units began on April 1, 1942. Charging of the reverberatory furnaces commenced on April 18, 1942, and the first anode copper was produced on April 26, 1942. The smelter was originally designed to handle the production of the Morenci Concentrator on a 25,000 ton per day program, but by the time the smelter was in operation, plans were already underway to increase the smelter capacity to handle the production of the concentrator which was being enlarged to 45,000 tons a day capacity as a war-time necessity. This extension to the smelter was completed and the new units were put in operation toward the beginning of 1944. The original smelter consisted of a smelter crushing plant, bedding plant, two direct-smelting reverberatory furnaces with two waste-heat boilers on each furnace, three converters, an anode department, a stack, and all of the usual accessory smelting equipment. The extension consisted of increasing the bedding plant from three to five beds, the reverberatory department from two to four furnaces, and from four to eight waste-heat boilers, and the converter department from three to six converters. A third converter aisle crane was added and additions were made to the flue systems and conveyor systems throughout the smelter; but no change was made in the smelter crushing plant or the anode department, and the same stack was used for all additional Smelter units. A blister casting machine was installed at that time in the south end of the converter aisle to handle excess and emergency production above the capacity of the anode department and in 1947 a converter aisle skull breaker and a lime burning plant were added as the final units for a complete plant. The choice of direct smelting over calcine smelting for the Morenci Smelter was made after careful study by members of the Western organization of Phelps Dodge Corporation and after test runs on direct smelting of Morenci concentrate had been made at the Douglas Smelter of Phelps Dodge Corporation. The Morenci furnace charge is made up of comparatively high grade concentrate with no ores of smelting grade available and with only flux, a small amount of copper precipitate and the usual amount of smelter secondaries to be smelted with the concentrate. The simplicity of direct smelting for this charge and the large amount of waste-heat steam available from direct smelting operations were factors influencing the decision to adopt direct smelting for Morenci. The design of the Morenci Smelter and the type of units selected followed best experience at the Douglas Smelter of Phelps Dodge Corporation. A description of the original smelter before operations started was given in an article in the May 1942 issue of Mining and Metallurgy. The purpose of the present article is to describe the enlarged Morenci Smelter, with a discussion of metallurgy and operating practice and to show tabulations of operating and metallurgical results obtained. Because of beginning operations during the early years of World War 11, many problems caused by labor shortage were encountered, but no major difficulties developed in starting the new plant. However, because of labor shortage, full scale Smelter production was not reached until the fall of 1946. Fig 1 shows a general plan of the Morenci Reduction Works. The arrangement of the smelter equipment is shown in Fig 2, a sectional view of the smelter is shown in Fig 3, and the smelter flow sheet is shown in Fig 4. Metallurgy The metallurgy of direct smelting, being more or less fixed by the character of the charge, is not subject to the control available in calcine smelting. Slags may be modified by the addition of suitable fluxes, but the grade of the matte is determined almost entirely by the iron:copper ratio of the concentrate. The direct smelting operation involves distributing the wet concentrate along the sidewalls and in the bath of a reverberatory furnace by means of some suitable feeding device and raising the temperature of the charge so that first the moisture is driven off, then the first-atom sulphur is eliminated, and finally the sulphide portion of the charge melts and runs into the bath, carrying with it the non-sulphide portion which has been partially fluxed to form a suitable slag. The fusion of the non-sulphide portion is completed by contact with the irony converter slag which is regularly being poured into the reverberatory furnace. The smelting rate of the charge is influenced by the mineralogi-cal composition of the sulphide portion of the concentrate and by the composition and amount of the non-sulphide portion including the fluxes added. The copper in Morenci concentrate is chiefly in the form of chalcocite, intimately associated with pyrite, and non-sulphide content is very low so that

Jan 1, 1950

By B Beale

Bow-tie analysis is a commonly used tool in the Major Hazard Facility sector to identify, display and control risks that have the potential to pose serious harm to personnel. It is a simple but powerful risk management tool that displays traditional risk assessment outputs as easily interpreted ‘bow-tie diagrams’. These are an effective and versatile communication format that can be applied to any type of risk (eg safety, environmental, assets etc) and as such show great benefit in managing operational hazards in mining.

May 5, 2022

By Robert F. Brindisi

There are approximately thirty to forty operating mills in the United States which are currently producing uranium yellow cake. This figure includes a significant number of in situ and by-product operations however the conventional acid leach flowsheet depicted in Figure 1 is the most common process used by domes- tic yellow cake producers. Ground ore is leached with sulphuric acid and the solids are separated from the pregnant liquor and washed in a series of counter- current decantation thickeners. After clarification of the pregnant liquor, uranium is recovered from the solvent extraction/stripping circuit by the addition of ammonia with precipitation of ammonium diuranate, or simply yellow cake. The yellow cake precipitate is then thickened in a conventional thickener before re- porting to the dewatering/washing unit operation. De- watered solids subsequently report to thermal drying, and clarified liquor from the dewatering/washing step is recycled to the yellow cake thickener. The yellow cake dewatering/washing unit operation is generally accomplished using either a solid bowl centrifuge or a rotary vacuum drum filter. In most cases the underflow from the yellow cake thickener is pumped to the dewatering/washing unit operation at approximately fifteen to twenty percent solids. For the purpose of this discussion ammonium diuranate, the product of ammonia precipitation from a conventional acid-leach uranium mill flow sheet, as discussed earlier, will be considered. With only slight adjustment this discussion will be equally applicable to sodium diuranate or uranium perioxide precipitates and to either in situ or by-product operations where such precipitates are generated. Some of the domestic uranium mills which have selected solid bowl centrifuges instead of vacuum drum filters for the dewatering/washing unit operations are listed in Figure 2. Why have these uranium mills, as well as others not listed, chosen to use the solid bowl centrifuge for this particular application? It is simply a matter of performance, reliability and economics. In the remainder of this paper the performance, initial cost, installation cost, maintenance and power consumption of both the solid bowl centrifuge and the rotary vacuum drum filter will be com- pared. In order to provide a consistent basis for comparison the appropriate sized (centrifuge or filter) unit for the dewatering/washing of 400 to 500 pounds per hour of yellow cake solids will be considered. Such a flow will usually be generated by a typical 3,000 ton per day (acid-leach) uranium mill.

Jan 1, 1980

By T. Wajima

"A novel carbonaceous immobilizing agent for heavy metal contaminated soil was prepared from rice straw using sulfur immersion and pyrolysis, and the lead immobilization in artificial contaminated soils using sulfur-impregnated carbonaceous material was estimated. The rice straws were cut to 1 cm pieces, and then immersed in 0.1 - 1 M K2S solution for 0 - 24 h to prepare sulfur-immersed materials. The immersed-materials were heated at 400 oC for 1 h in nitrogen gas to produce the sulfur-impregnated carbonaceous material by pyrolysis. The abilities of the product to immobilize lead from aqueous solution were examined to obtain the product with high lead immobilization ability. With increasing K2S concentration, the immobilization ability of the product for lead gradually increases and then above 0.5 M K2S those are almost constant, while 15 min is sufficient for the immersed time to obtain the product with high lead immobilization ability. The product prepared from material immersed in more than 0.5 M K2S solution for less than 15 min has a maximum immobilization ability for lead ion. The lead immobilization using the sulfur-impregnated product is sustainable due to the formation of leadhillite [Pb4SO4(CO3)2(OH)2] and anglesite [PbSO4]. The product can immobilize lead ion in various artificial lead contaminated soils. By mixing artificial lead contaminated soil with the sulfur-impregnated product, the eluted solution became neutral, and the eluted concentrations of lead ion dropped below the Japanese elution standard for soil.INTRODUCTION Soil contamination with heavy metals is a worldwide problem. Accumulation of heavy metals in soils affect soil ecology, agricultural productivity, quality of agricultural products, water resources, and serious health problems for human and animal (Raicevic, et al., 2005). In the United States, for example, approximately 63 % of the sites on the National Priority List (NPL) for the treatment of contaminated soils are contaminated by metals, and lead is the most common metal, found at 15 % of the sites. In Japan, according to a report by the Ministry of Environment, 43 % of the contaminated sites that exceed the environmental quality standards are contaminated by lead compounds. Soil contamination by lead compounds is also prevalent in other developed and developing countries where lead compounds are used extensively in industrial activities without careful contamination management. Lead is a ubiquitous heavy metal pollutant in soils due to their use widely. The primary sources of Pb contamination include industrial activities such as mining, smelting of metals, and the use of Pb-containing products such as paints, lead-acid batteries, bullets, gasoline and pesticides (Cao, et al., 2009). It can damage human nervous (especially children) and reproductive systems (ATSDR, 2007). The high concentration of Pb in the soil poses risks to human and animal health by the leaching of metals from the soil into water and the consumption of edible plants growth in the contaminated soil. Therefore, proper remediation is necessary to reduce metal availability in soil for protecting human health."

Jan 1, 2018

By Michael J. McGuire

Rostoker, Inc. has developed a process to smelt solid hazardous/non-hazardous inorganic wastes. Near seven hundred experiments were performed. Actual industrial wastes as well as reagent grade chemicals were used. By mixing a multiplicity of these wastes to proper formulations, then furnacing them, it was determined that saleable end products could be reclaimed; metal, fume and slag. The slag, due to its siliceous structure was tested to be leach resistant (40 CFR). This formed the essence of our patent, #5,180,421 "Method and Apparatus for Recovering Useful Products from Waste Streams". What is unique is that a HTMR (High Temperature Metal Recovery) process has been developed that can treat a multiplicity of wastes within the same furnace. The discussion will include a list of waste streams we have treated, details of proper waste formulation and experimental results.

Jan 1, 1994

By R Varden

Friction rock stabilisers, commonly termed ‘Split Sets’, friction rock bolts, or continuous friction coupled bolts are the most widely used rock bolt in the Australian underground metalliferous industry. Historically, they were used for temporary reinforcement, mainly within ore development. However, their use as primary reinforcement has grown with the demand for higher development rates at lower costs. The introduction of galvanisation has increased their longevity and pattern bolting in conjunction with weld mesh, specifically made for use in development headings, has allowed the use of friction rock stabilisers to increase rapidly with development jumbo’s undertaking the installation. The installation of friction rock stabilisers appears to be deceptively simple, particularly when compared to resin encapsulated bolts. The friction rock stabilisers capacity is a function of the borehole parameters, rock mass quality/strength, the bolt dimensions and steel quality, and lastly and perhaps the most important the operator skill levels. However, as in industry we are still seeing common occurrences of friction rock stabilisers not reaching their design pull test capacity. Pull testing the friction rock stabilisers is used to verify the installation of the design capacity. It involves loading the collar of the bolt with a hydraulic ram until the design load is reached or the bolt slips. Pull tests often show failure rates of 20 per cent or higher. This is despite over 40 years of use and with millions of units installed annually. Such high failure rates would suggest there remain issues with the quality of installation. Ground support quality assurance and quality control (QAQC) programs are needed in combination with operator training to ensure that pull test failure rates are kept as low as practical. However, there are times when despite the QAQC being completed the pull test failure rates increase quite suddenly. When this occurs, it is important to conduct a thorough investigation. These investigations often show there are several factors that are not obvious to personnel installing the bolts. To complete a useful investigation, it must also be done methodically, working through the entire process that includes less obvious factors such as steel quality and the calibration of the hydraulic pull test kit. The aim of the paper is to give mine practitioners an understanding of the complexities of friction rock stabilisers, what QAQC requirements they should be doing on-site, what can go wrong during installation and, if necessary, a process of how to conduct investigations into high friction rock stabiliser pull test failure rates.

Mar 29, 2023

By Norman C. Stines

Russia's mineral potential is a secret that has been effectively kept by the Iron Curtain. There is no conclusive data and because of its extreme importance to the Free World, the subject is greatly discussed. Opinions range from those presented by Paul Tyler in his article "Russia's Mineral Potential," June issue of MINING ENGINEERING to those of Norman C. Stines, presented herewith. Mr. Stines is a consulting mining engineer of Los Gatos, Calif. He was in Russia, China, and Manchuria from 1909 to 1918 as a mining executive. From 1917 to 1919 he served as assistant military attache Intelligence Branch U. S. Army in Petrograd, Russia.

Jan 11, 1951

By M. J. Ferrante

Enthalpy and entropy increments above 298.15° K were determined for cop-per sulfate between 298° and 1,000° K and for copper oxysulfate between 2980 and 1,146° K by the method of copper-block drop calorimetry. Enthalpies, entropies, and heat capacities are tabulated for both compounds. In addition, free-energy functions are tabulated for the sulfate. Equations representing the enthalpies are given for each compound.

Jan 1, 1972

By Yunyan Wang

Diagrams of pc-pH for the complex ions concentration and pH value and -g- for activity coefficient and ionic strength ln±MnSOI4had been drew based on the thermodynamic principle of coordination chemistry and combined with Pitzer theory at 298.15K. The diagram of -g- indicated that -gincreased sharply from 0.0000 up to 1.2147 when I changed from 0.00 ln±MnSOIln4±MnSO4to 0.09; The increase of -gbecame slowly when I was more than 1.00 and less than 1.69; kept still when I ln±MnSOln4-g±MnSO4was more than 2.25 and less than 4.00. Diagrams of pc-pH illustrated that the minimum solubility of Mn(OH)2(s) increased with the increase of I, the pc increased from 6.5 to 5.5 when I increased from 0.00 to 4.00; The pH of the minimum solubility of Mn(OH)2(s) increased with the increase of I, the pH increased from 11.80 to 12.76 when I increased from 0.00 to 2.89, the pH kept still when I (I was less than 4.0) increased. There is single function relationship between the minimum solubility of Mn(OH)2(s) and relevant pH in different I.

Jan 1, 2010

Continuous, steady-state laboratory flotation tests showed that the recovery of cha1copyrite from a naturally occurring ore, under conditions closely resembling those of plant practice, could be expressed in terms of a first order rate equation.Tests on full-scale plant flotation cells, using impulse tracers, indicated ideal mixing of the pulp in the cells.It was demonstrated that values of first order flotation rate constants can onlv be obtained from conventional methods of analysis in special cases.Analysis of a plant sampling campaign by the author supported a first order kinetic equation for two mineral species, and for the individual size fractions of one of these.The effect of stage-addition of reagents is interpreted in kinetic terms.

Jan 1, 1966

By Ronald T. Mayerle

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 20,500-acre part of the 104,085-acre Rincon Wilderness Study Area (OR-002-082) in order to evaluate its identified mineral resources. The wilderness study area is located in Harney County, OR, about 12 miles west from Fields. No mineral resources were identified within the study area. A literature search found no records of mining or minerals exploration, nor did a ground search find any evidence of mining-related activity. Of seven alluvial samples taken from the major drainages of the study area, all were barren except one. This sample, taken from a dry streambed along the southern boundary, contained $0.07 gold per cubic yard; however, this small amount of gold is of no economic significance, and the source is probably outside the study area. The Pueblo-Steens mining district extends to within 4 miles east of the study area. No evidence of geological environments similar to those that were responsible for the formation of resources or occurrences of metals and nonmetals within the district is known within the study area.

Jan 1, 1987

By L. Magne, A. Pinto, M. Maldonado, J. A. Finch

Estimation of gas holdup from electrical conductivity measurements has been used in lab and industrial installations. The approach is based on the application of Maxwell's model, which relates the concentration of a dispersed phase in a continuous medium to measurements of the electrical conductivity of the dispersed phase, continuous medium and the resulting mixture (dispersion). When applied to inferring the collection zone gas holdup in a three phase system and to facilitate real-time on-line measurement, the slurry is assumed to behave as the continuous medium and gas bubbles as a nonconducting dispersed phase. This article derives an equation for estimating gas holdup in a three phase system, eliminating the assumption that the slurry behaves as a continuous medium but rather as a dispersion of non-conducting solid particles in water. In this formulation only water behaves as the continuous medium in the sense of Maxwell, and gas holdup in a three phase system is then calculated from the application of the Maxwell model twice: (1) to determine solid content in a two-phase system, and (2) to determine solid plus gas holdup in a three phase system. To validate the new equation and quantify the errors incurred by assuming slurry is the continuous phase a laboratory flotation cell was instrumented to continuously measure the conductivity of two and three phase dispersions with known solids contents. As the amount of gas in a lab flotation machine is difficult to measure directly or by another indirect technique such as using pressure signals, 2.5 mm dielectric plastic spheres having a density of ca. 1.3 g/cm3 were used instead of air bubbles for validation. Experimental results demonstrated that the continuous medium assumption underestimates gas holdup and that the resulting bias error increases linearly with the solid content and decreases with the magnitude of gas holdup.

Jan 1, 2016

By Dinesh P. Amalnerkar, Nagegownivari Munirathnam, Tirthalli Prakash, Katia Vutova, Vania Vassileva, Veliko Donchev

"A time-dependent model for electron beam melting and refining (EBMR) of different metals and alloys is developed. The model is 3D axi-symmetrical and an adapted numerical scheme of Pismen-Rekftord type is applied. The developed computer program computes the thermal fields in the metal ingots during EBMR process as well as the dynamics of the thermal streams and the geometry of the molten metal pools. Calculated results for different regimes of EBMR of titanium are obtained and discussed in the paper. Experiments are performed and impurities' concentration data are presented. Simulation results are compared with experimental data and are used for optimization of the EBMR process in the case of Ti.IntroductionElectron beam melting and refining (EBMR) has an important role in the special electrometallurgy[ 1-6] and it is approved for obtaining of pure titanium [7]. EBMR of metals and alloys is being recognized as a competitive and even the single method for obtaining new materials for all areas of human activity.The principal scheme of the EBMR drip process is shown in Fig.1. A thin layer of molten metal is formed on the front part of the feeding rod during the e-beam processing and generated droplets fall into the molten pool in the crucible where the ingot is formed. The refining is mainly realized at the boundary liquid metal - vacuum. There are three zones in EBMR (Fig.1) - on the front part of the feeding rod (zone I in Fig.1 ), on the surface of the generated droplets (zone II in Fig.1) and the surface of the molten pool in the water-cooled copper crucible (zone III in Fig.1)."

Jan 1, 2013

By G Mendoza, L Taddei, C Robertson

It is a well-known industry fact that many mine sites around the globe experience blast holes that have elevated temperatures due to reactive ground, geochemical reactions, geomorphic reactions, sub level open fires, etc. It has been reported in many previous industry publications (White, Saputra et al) that elevated blast hole temperatures are a norm at many mine sites and are dealt with on an ongoing basis while the drill and blast process continues under elevated states of alert. The choice of explosives products including the type of detonator, primer, accessory, and bulk product all must be taken into consideration when loading blast holes where there is a known potential for elevated temperature conditions. It should also be noted that these elevated temperatures inside blast holes can be consistent throughout the blast hole length or vary in position within the blast hole depending on the mine conditions mentioned in the opening statement above. The risks associated with the loading of primers and bulk explosives in holes where elevated temperatures are present include: the ejection of the bulk explosives product, deflagration of the explosives during initiation of the blast or premature and uncontrolled initiation of a blast hole(s). This paper describes a unique and novel approach to the active monitoring of the temperature within blast holes with the application of electronic detonators with integrated temperature measuring (ITM) capabilities, deployed and demonstrated at a mine site in Mexico during January 2023 to March 2023. The deployment of ITM capable electronic detonators allows a user to monitor and record the real time temperature at multiple locations (e.g., toe, middle and collar) at each electronic detonator’s position within the blast hole, with the ability to react instantaneously to elevations in temperature reported. The measurement of the temperature can be for a single ITM electronic detonator, or simultaneous for an array of ITM electronic detonators, allowing for the potential for the data to be represented by a time/temperature/hole depth three-dimensional heat map. Changes in temperature at different borehole positions can vary, however, often the collar position is expected to be the most reactive due the combination of bulk explosive product and oxygen exposure, which can be confirmed with the application of the ITM electronic detonators. A mine site’s reaction to a measured elevated temperature within a blast hole can vary depending on the temperature measured and the change in temperature from the last measurement made. The study was found to produce real-time in-hole temperature information which was previously unobtainable without the introduction of another device. New and adaptive elevated temperature hole policies can be created and adapted proactively as real time information is received, leading to a safer mining operation.

Jan 21, 2025

By M. Fall

The progressive depletion of ore available at shallow depths in several underground mines around the world means that underground mining operations would increasingly be carried out at greater depths and therefore at higher temperatures. However, our understanding of the effect of hot temperatures on the response (mechanical, economical, environmental) of cemented paste backfill (CPB) is still limited. Hence, an extensive laboratory investigation was conducted to study the performance of young and aged CPB, in response to deep mine temperatures. Several CPB samples with different compositions, cured at different temperatures (20 to 50°C) and different times (7 to 160 days) were tested regarding their mechanical properties, economical performance (binder consumption) and microstructural properties. The results show that hot temperatures significantly affect the performance properties of CPB at young and advanced ages. An increase in the curing temperature leads to a considerable improvement of the rate of gain of CPB strength and also to a significant increase of the strength of CPBs studied. CBP samples cured at hot temperatures show lower binder consumption and finer pore structure. Results of this study could serve as background information for the development of optimal mine backfill design procedures.

May 1, 2007

By Lemberg D. W, Friday R. G

Potential means of lowering overall costs to permit deeper stripping include : 1. the use of larger diameter blastholes in highly-fissured strata (to reduce drilling costs); 2. dewatering from semi-permanent bores to reduce blasting costs (by maximising the use of bulk ANFO) and promote highwall stability; and 3. the use of inclined blastholes, bulk AN, staggered V1 patterns, adequate backfill and more cost-effective stemming columns. Each of these is covered. The pumping of bulk watergels continuously raises the blasthole water column, thereby perpetuating the demand for these blasting agents. This must be a principal consideration when choosing between a bulk and a packaged watergel. Any packaged product should exhibit dimensional permanence and an energy yield per metre length equal to that of bulk ANFO. Possible ways in which controlled trajectory blasting (CTB) could benefit deeper stripping operations are outlined. By allowing the maximum use of bulk ANFO, de- watering may be a prerequisite of a viable CTB Operation.

Jan 1, 1981

By J. A. Meech

An analysis of screen design options on the operating efficiency of secondary crushing plants has been conducted using a dynamic computer model. The model allows for the simulation of a wide variety of crushing circuits and can be run on either a microcomputer (IBM PC/XT) or a large time-sharing mainframe computer. Size reduction and separation characteristics of crushers and screens are based on standard manufacturer design and performance data. Input/output routines are available in tabular, alarm or strip chart recorder modes to facilitate operation of the program. A number of alternate circuit designs are compared to show the influence of surge capacity, screen size and area, screen deck location, and closed side crusher settings on the operation of a 10,000 ton per day plant. The program is currently in use at Queen's University to teach plant operations and control. It has potential to be a valuable tool for operator training.

Jan 1, 1985