Search Documents

By S. Martins

The aim of this work is to compare three different results of charge motion in a modified 5ft diameter lab mill and to identify differences and similarities in these results. The lab mill is modified from tumbling a ball charge to tumbling a charge of disks. This modification replicates 2D motion. This 2D condition is measured using an instrumented disk (iDisk) and analysed using a video imaging system. The iDisk is equipped with a 3D accelerometer array and rotation rate sensors. With the help of a video system, some measured quantities are also determined externally. The results of these three predictions or measurements are presented. A discussion is included.

Jan 1, 2014

By W. M. Schafer, C. F. Luckay, D. A. King

Monitoring devices have been installed at several mine sites to assess the potential for the development of acid rock drainage (ARD) in waste rock, spent ore and tailings material. In addition, instrumentation has been designed for monitoring changes in water quality in pit lakes. These devices monitor temperature, oxygen, water movement and water chemistry in the waste rock pile. This information can be used to evaluate the current and future ARD risks and the effectiveness of caps and covers. The information can also be used in the design of other reclamation strategies that limit ARD development. The instrumentation includes nested thermistors and oxygen sensing ports, neutron access tubes, heat dissipation units (HDUs) and lysimeters. Many of the monitoring devices can be linked to a data logger and telemetry systems, enabling monitoring data to be downloaded from the office.

Jan 1, 1999

By Luis Acainas Caballero, Karl Hoen, Stephan Krämer, Christoph Klein

The situation of the steel industry is still challenging. Worldwide overcapacities have an impact on profitability. More than ever, the point at SMS group is to provide the steel industry with flexible and profitable technologies and systems over the whole process chain. One example for that is the thin slab casting and rolling technology and, in particular the CSP® technology (Compact Strip Production), being well established for hot coil production. From its introduction in 1989, CSP® technology has been continuously further developed. Today, on a CSP® plant, the full range of high-quality steel grades can be produced with tightest geometrical and metallurgical tolerances under optimal economic conditions. With the introduction of semi-endless rolling and, as a further step, the endless rolling process, the product range for thin and ultra-thin products has been further enlarged, allowing for the production of hot rolled coils with a thickness of 0.8 mm for low carbon steel grades. Also high-strength steel grades may be produced with gauges below the minimum product thickness that can be achieved in a conventional-type hot rolling mill. Another step in the further development of CSP® technology is digitalization. In December 2016, the CSP® plant of Big River Steel (BRS), located in Arkansas, USA was put into operation. It is the first learning steel mill in the world. The CSP® plant of BRS comes with innovative technologies, providing impressive operational results right from the beginning.

Oct 1, 2019

By R. A. Meyr, K. A. Perry

Following three major mining accidents in 2006, the MINER Act of 2006 was enacted by the U.S.Congress. The U.S. Mining Safety and Health Administration subsequently released the Final Rule on Refuge Alternatives for Underground Coal Mines, which required every underground coal mine to install refuge alternatives to help prevent future fatalities of trapped miners in the event of a disaster. The following paper documents the research that was performed on a structural wall to be used in conjunction with a breathable air system to create a refuge alternative. A 103.4-kPa (15-psi) safe haven polycarbonate wall for use in underground coal mines was designed and modeled using finite element modeling in ANSYS Explicit Dynamics. The successful safe haven wall design was modeled for an actual underground coal mine environment using the explicit finite difference formulation program FLAC3D to determine the responses of the wall and surrounding strata within a mine. A full-scale design was fabricated and installed in an underground coal mine to determine any construction constraints and as a final step in proof of concept for the safe haven wall design. This paper is meant to introduce the reader to a new wall concept to be used in conjunction with current technology.

Jan 1, 2013

By R. M. Board

This paper will focus on measurement and control of four main aspects of crushing, namely horsepower, bowl level, mantle position and feed rate, and will discuss related sensors and control techniques, some of them designed specifically for crusher control, that have proven successful and reliable in many installations.

Jan 1, 1982

By James S. Redpath

"AbstractThis paper is an attempt. to outline the present status of underground mining contracting in Canada, and to present certain facts concerning the writing and administration of underground mining contracts which, hopefully, may be useful to those intending to engage a mining contractor . The paper is based on the author' s experience as a contractor and also as a consulting engineer advising others in the purchase of contractors' services.HistoryIN THE early days of mining contracting in Canada, the contractor was primarily a labour contractor. He was expected to bring a good crew of men that normally followed him, and to perform certain work under his own direct supervision. The owner usually looked after all other details including financing, payrolls, withholding taxes, etc , computing and paying the contractor his profit. In the pre-World-War II years, most work was done on this basis.Over the years, the contractor was called on to supply more in the way of services, and the present-day situation evolved.Labour contracts are still used, but now the contractor is expected to carry out his own administration. Most contracts now call for the supply of special tooling required to do the work. In most cases, some, if not all, supplies are the contractor 's responsibility and , in a growing number of cases, the contractor is responsible for such items as design and surveying. The ultimate in this direction is the execution of projects on a turnkey basis. Under this system , the contractor carries the project to a stage where it is turned over fully operational to the owner."

Jan 1, 1977

By Michael McClintock, Bern Klein

"The high pressure grinding roll (HPGR) is a relatively new comminution technology that is gaining popularity for providing energy efficient solution to hard rock mining operations. A significant barrier to increased adoption of HPGRs is the present requirement for large amounts (excess of 2 tonnes) of sample for pilot testing, which may not be possible for most early stage projects. Three methodologies have been developed at NBK Institute of Mining Engineering at the University of British Columbia that may be used for sizing design optimization of HPGR circuits. All three methodologies use a MTS pistonpress to simulate HPGR comminution. These tests are capable of providing information regarding energy consumption, energy breakage relationship, reduction ratio, and product size distributions. In a period of slow economic development, these methodologies are critical to allow the industry to cost effectively understand the operational benefits of HPGR implementation. This paper examines previous test work done at UBC, as well as the development of an HPGR and piston press database for use in sizing and budgeting of HPGR circuits.INTRODUCTIONCurrently, the mining industry faces several challenges due to falling commodity prices and escalating costs. This has applied pressure for operations and projects to reduce costs and improve project economics. In addition engineering and metallurgical budgets have shrunk as companies try to conserve cash. Improvements and optimization of milling and comminution circuits is one area project economics may be significantly improved. By considering alternative comminution technologies such as the high pressure grinding roll (HPGR), energy operating costs may be greatly lowered. Many have begun to implement HPGR crushing as an alternative to semi-autogenous grinding (SAG) mills, including KGHM and, Sierra Gorda, and Freeport Mc-MoRan’s Cerro Verde operation. However, implementing new technology for companies with little or no HPGR experience may not be practical. An operator must consider both feasibility and economics of a circuit. Currently, consideration of the HPGR requires expensive pilot scale testing for which large sample sizes are needed. In addition, few laboratories are equipped for running pilot scale HPGR test programs. Furthermore, the results of pilot HPGR testing are dependent on the quality of the sample, which cannot represent variations across a deposit. In contrast, ball mills and SAG mills can be sized using the Bond Mill Work Indexes that require a small amount of sample which enable a number of different geological blocks to be tested to allow engineers to have a complete understanding of how the comminution circuit will perform for the life of mine."

Jan 1, 2016

By Karina Forster

Open stope design depends on the ore body geometry, loading conditions and rock mass properties to estimate stope dilution and ground support requirements. Rock mass conditions for design primarily rely upon estimates of well established rock classification systems. Many sources of data exist for obtaining estimates for these rock mass classification values which include core logging, geotechnical mapping, geological mapping as well as linking one classification system to another through the use of empirically derived equations. The extent of mapping coverage can also vary significantly based on the data collection technique. This paper proposes an approach where individual components of rock mass classification systems are collected by the different available data collection techniques. Data from different rock types are also considered separately based on their alteration characteristics and general observation products. Data from the Cameco Corporation Eagle Point Mine is presented and an approach is outlined for obtaining average representative classification values for stope hanging wall characterization. The effectiveness of this approach is demonstrated through the analysis of a data base of hanging wall dilution information.

Jun 1, 2012

By E. M. Cox, A. S. Skapski, N. H. Nachtrieb, M. C. Bachelder

As a result of using copper-containing scrap in the steelmaking process, the copper content of steels has been steadily increasing for years. Consequently the possible role copper may play in the steelmaking process and in the finished product begins to attract the metallurgists' attention. Some time ago one of the present authors forwarded the idea—based on the results of the analysis of nonmetallic inclusions extracted electrolytically from steels—that sulphur in plain carbon steels is distributed mainly between copper and manganese, the amount of iron sulphide being very small; and that, consequently, the problem of copper and that of sulphur in steel cannot be treated separately.' At the time of the publication of the quoted paper little was known about the relative affinities of copper and manganese for sulphur at high temperatures except that at moderate temperatures (below 1000°C) the affinity of manganese for sulphur is much greater. To gather more experimental data on this subject, the present authors undertook the investigation of the equilibrium constants of the reactions: 2Mn(8 or 1) + S2(g) = 2MnS(s) 4Cu(s or 1) + S2(g) = 2Cu2S (S or I)* 2Fe(s) + S2(g) = 2FeS (s or 1) over a range of temperatures wide enough to establish the dependence of these equilibrium constants on temperature. From the equilibrium constants (K = l/Ps2) the free energy of formation (affinity) can be calculated from F° = -RTln 1/PSt (1) where the standard conditions chosen are: 1 atm of sulphur pressure and the activities of condensed components equal one. The decomposition pressure, Ps2, of sulphur over the respective sulphides is too small to be measured directly, but there is a way of eliminating this difficulty by measuring the equilibrium constant of the reaction between the sulphide and hydrogen. From the latter and from the equilibrium constant of the thermal dissociation of H2S we then calculate Ps2 for the respective sulphide. 2Mn + 2H2S = 2MnS + 2H, 2H2 + S2 = 2H2S_________ 2Mn + S2 = 2MnS The numerical values of the equilibrium constant of the thermal dissociation of H2S at different temperatures were taken from Kelley's paper, "The Thermodynamic Properties of Sulfur and its Inorganic Compounds."² In previous experimental work published by Jellinek and Zakowski3 and by Britzke and Kapustinsky4 the equilibrium constants of the reactions Metal sulphide + H2 = H2S + metal were determined by passing hydrogen, at different rates of flow, over the sulphide, analyzing the resulting H2S + H2 mixture and then extrapolating the H2S/H2 ratio (which is a function of the rate of flow) to the zero speed of flow, a method necessarily involving considerable uncertainty. In the present work the equilibrium ratio was actually measured instead of being extrapolated. The apparatus is shown in Fig 1. Experimental Procedure The sulphides were prepared by the following methods: FeS Powdered iron which had been reduced with hydrogen (ferrum reduc-tum) was mixed in stoichiometric ratio with sublimed sulphur and carefully ground. The mixture was put into an alundum crucible, covered with pure sulphur, and the reaction started by touching the mixture with a glowing iron rod. After the reaction was completed the product (still containing some metallic iron) was again ground with sulphur, put into a Rose crucible, covered with sulphur, and heated in a strong current of pure hydrogen. Analysis of the final product showed 62.46 pct Fe and 36.59 pct S. Theoretical for FeS: 63.53 pct Fe and 36.47 pct S. MnS Manganese sulphide (precipitated and carefully washed with distilled water containing H2S) was dried in a Rose crucible in an atmosphere of H2S and heated in a current of hydrogen for 2 hr at red heat. The product was then ground and ignited for several hours at 1000°C in a current of hydrogen sulphide. Analysis showed 64.53 pct Mn and 36.63 pct S. Theoretical: 63.15 pct Mn and 36.85 pct S. Some MnS samples were prepared from metallic manganese and sublimed sulphur by mixing and grinding them and then heating in a current of hydrogen sulphide in an alundum tube.

Jan 1, 1950

By Graeme Heyes, Warren J. Bruckard, Michael A. Somerville

"A limited series of laboratory batch flotation tests was conducted on a suite of calcium-ferrite-based slags made in laboratory smelting trials. The smelting tests were conducted as part of a wider CSIRO Minerals’ research project aimed at developing a single-stage continuous copper-making process. The objective of the flotation work was to maximise copper recovery and iron rejection from slags made in the process.The slags treated included a reduced low copper slag, an oxidised high copper slag composite, and a very reduced low copper self-pulverising slag. The copper content of the slags varied from 2.9% to 14% Cu. The copper was present as metallic copper, oxide copper and copper-calcium ferrite phases with the phase mix related to smelting conditions. The slags were crushed, ground, wet-screened at 355 or 210 µm to remove coarse metallic particles of copper, and floated at natural pH (about pH 11) using reagents and conditions appropriate for the selective recovery of the copper phases.In rougher/scavenger tests on the reduced low copper and self-pulverising slags copper recoveries above 92% were obtained with copper enrichment ratios varying between 2.3 and 2.9. For the oxidised high copper slag copper recoveries were poorer - only 47% of the copper was recovered with an enrichment ratio of 3.3. The presence of the slow floating copper-ferrite phases in the slags limited further (selective) copper recovery. Ageing of the high copper slag, that is, a significant delay between grinding and flotation, resulted in a deterioration of the copper flotation response.The critical parameter affecting the flotation of copper from direct converting slags was found to be the form of the copper in the slag. Slags containing a higher proportion of the more desirable form of copper for flotation will provide the best opportunity for high copper recoveries to be consistently obtained, allowing improvements in the economics of the overall copper-making process."

Jan 1, 2003

By JOHN R. SUMAN

IT appears now that the conflict with the totalitarian states will be a long-drawn-out struggle. The course of this war up to now indicates that this may well be the first major conflict where man power has not been the vital and determining factor. Mechanized warfare has made it possible for relatively small, well-equipped groups to outmaneuver and defeat large armies which lack the necessary modern equipment. Under these circumstances, ultimate victory becomes a matter of resources and productive ability. The important question is not how many soldiers can he put into the field, but the volume and speed in producing the armaments essential to ensure a victory. The resources available to the opposing nations and the efficiency of their systems of enterprise and production will be primary factors in determining the ultimate outcome. Germany had a head start of eight years in the armament race, and it is not easy to overcome such an advantage overnight.

Jan 1, 1942

By Lester G. Rollins

Coal today enjoys a dominant position, serving the energy and metallurgical marketed The measure of success in the market place is, and will continue to be, the price per million BTUs or price per ton delivered to the user. The Coal Industry's remarkable record of price stability since World War II is well known. The next twenty years promise to be equally as challenging. This challenge will be met our president, Mr. Drain, has often stated that, ?The Joy Manufacturing Company is betting that coal will meet the challenge.? To this end, the resources of Joy have been committed to doing its part. Joy's efforts are directed toward a target which has been defined as: 1. Deliver coal to the user at a price of $.15/MBTU or less. or; 2. Deliver coal to the mine portal at a cost of $1.00 or less.

Jan 1, 1966

By C. W. Smith

Research was conducted to evaluate the effectiveness of a well-point dewatering system in conjunction with a french drain to intercept waste impoundment leakage while reducing the volume of waste water requiring treatment. A well-point dewatering system composed of 585 production wells was installed around the perimeter of a leaking impoundment that previously used only a french-drain system for leakage control. The placement of the well-point system was designed to intercept and remove the leakage from the groundwater before the contaminant reached the french drain. Groundwater monitoring at this site revealed that after a period of approximately 40 days the well-point dewatering system had stabilized and effectively prevented the further spread of contamination to the french drain.

Jan 1, 2010

By James A. Wasson

This report summarizes the results and conclusions reached by various investigators who have attempted to determine the extent to which hydraulic fracturing will affect the secondary recovery of crude oil by waterflooding. It also discusses the most advantageous use of this well-stimulation method in waterflood projects. A thorough search of the literature was made, and pertinent information was abstracted from appropriate reports. A carefully designed and controlled program of formation fracturing is an effective aid in waterflooding because it increases water-injection and oil- production rates. Generally, fracturing has resulted in little or no reduction in ultimate oil recovery, but under certain circumstances recovery has been substantially increased.

Jan 1, 1963

By Ian Vaz, Takefumi Takuma

"The New Orleans area has been repeatedly flooded by major storms and hurricanes since its French colonial era. After severe flooding in May 1995, the U.S. Congress authorized a massive flood protection project called the Southeast Louisiana Urban Flood Control Program (SELA) in 1996 to improve interior drainage in Orleans, Jefferson, and St. Tammany parishes. However, the project was not fully funded before the landing of Hurricane Katrina in 2005 and Hurricane Rita, which breached many of the area’s levees and flooded 80 percent of the city. Finally, the project was fully funded in 2008 and has been worked on towards its 2017 completion. Another large project simultaneously worked on in the area is the Hurricane and Storm Damage Risk Reduction System (HSDRRS). This system was designed for a 100-year level of flood risk reduction. One particular project within the HSDRRS rendered successful due to an unconventional method of pile driving that was utilized to install sheet piles to reinforce an existing concrete I-wall. This paper will discuss how and why this non-vibratory method of sheet pile installation allowed the project to be successfully completed ahead of schedule.INTRODUCTIONSteel sheet piles were utilized on many of the SELA and HSDRRS projects for permanent cutoff walls under concrete I-walls or T-walls or for temporary earth retaining walls of drainage structures. Although the SELA Project was established in 1996 after severe flooding the year before, hardly any work was done on it until the two catastrophic storms Hurricanes known as Katrina and Rita triggered its revival. These two hurricanes also triggered the HSDRRS soon after the storms’ devastation. The SELA project authorized to improve interior drainage systems while the HSDRRS project was authorized to raise or restore levees and floodwalls mainly along Lake Pontchartrain, the Mississippi River, and Lake Borgne in addition to other areas. Figure 1 shows the SELA Projects that have been completed, are still under construction, or approved for construction. The projects fully highlighted in yellow within the map specified the press-in piling method. These improvements included drainage systems, pump stations, surge walls, and outfall canals as enhanced protection for future storms similar to Hurricane Katrina that caused so much damage by inundating the New Orleans area in August and September 2005 respectively (Facts and Figures, 2012). The completion of these projects were the responsibility of the U.S. Army Corps of Engineers, New Orleans District.Due to the fact that many of the projects were in densely populated areas, the Army Corps of Engineers specified a non-impact, non-vibratory press-in piling method for driving and extracting sheet piles for many of the projects to mitigate noise and vibration impacts. The soft soil conditions in the New Orleans area was also a contributing factor in the Army Corps of Engineers’ decision to specify this piling method due to the risk of settlement for existing historical as well as modern structures. In addition, there were other projects that elected to use the press-in method without any contractual requirements. One of these projects was the Inner Harbor Navigational Canal Reach II Emergency Interim Repair which was part of the HSDRRS project that has been under construction since its authorization in 2005 (Facts and Figures, 2012)."

Jan 1, 2017

By P. R. Taylor

Laboratory experiments have been performed to evaluate the kinetics of roasting pyrite and arsenopyrite in air at elevated temperatures, in the presence of lime. The effects of temperature, time, air flow rate, particle size, lime type, and mineral/lime weight ratio on the rates of oxidation, lime sulfation, and lime arsenation were studied. The reaction products were identified using chemical analysis, x-ray diffraction, SEM analysis, and optical microscopy. The results are discussed in terms of the utilization of lime to capture sulfur and arsenic during the roasting of refractory precious metal concentrates. More than 99.9% of the arsenic and 98% of the sulfur are contained when roasting pyrite and arsenopyrite with hydrated lime under typical roasting conditions.

Jan 1, 1991

By J Miedecke

A metalliferous mine has operated at Storys Creek from the 1890s to 1979. Storys Creek drains from a pristine catchment and National Park and remains as the most degraded stream from historic mining in north-eastern Tasmania. It has been the subject of public concern since the closure, particularly at times of high rainfall such as existed in 1985 and 1986. The mine is located on the banks of the creek, which flows into a major river, the South Esk River, which is one of TasmaniaÆs largest rivers and important for recreational fishing and water supplies. For much of the life of the of the operations tailings were directly discharged into the creek, and in latter years stockpiled or very close to it. Little rehabilitation was carried out at mine closure. The result was erosion and subsequent deposition on the banks of the creek downstream. Direct emissions of adit water and the consequential emission of contaminated ground water to the creek continue to affect water quality. Contaminant loads discharging from the mine and tailings comprise 70% of the metal load in the catchment and are by far the largest single source. Acidity data suggested that the introduction of systems to introduce alkalinity could be effective in ameliorating the residual acid drainage impacts in the Storys Creek catchment. After a period of investigations and trials which proved their effectiveness, treatments adopted have included the following: relocation of tailings to a constructed and clay capped disposal area and rehabilitation of tailings area; crushed limestone addition to stream flows; crushed limestone addition to creek banks and exposed tailings; sealing of a drainage Adit; and construction of an anoxic drain to generate alkalinity to surface waters draining to old mine workings. These innovative treatments have resulted in a marked improvement in water quality draining from the area. The anoxic drain is believed to be one of the few, if any, which has been constructed to have generated high levels of alkalinity from clean waters and offers a solution to the clogging problems experienced in such drains in the past. Similarly, the use of crushed limestone in an active stream has proved effective in buffering acid drainage and removing metals from solution.

Jan 1, 2003

By Zhi Zhang

The ever increasing demand of high performance rolls in the late finishing stands (F5 – F7) for hot strip mills (HSM) requires better product solutions from roll suppliers. Roll development activities never stop at Union Electric Åkers (UEÅ) in order to meet the requirement. The HYBRID STEEL, a new concept of roll materials especially for the late finishing stands in the HSM, is successfully developed in UEÅ. This paper reviewed the development of previous ICDP as well as enhanced ICDP (eICDP) roll materials, and, the novel HYBRID STEEL roll grade. Rolls manufactured by this new grade have been used in several European mills. A significant improvement over the enhanced ICDP rolls has been observed.

Oct 30, 2017

By D. M. Davidson

The economics of geologic exploration have changed materially in the past decade primarily due to the change in three basic factors, namely, increased wages and salaries, increased cost of materials, and a greater complexity in methods of exploration. Following the general economic pattern over the past ten years, exploration costs, have, in general, increased, although there is one heartening exception. A comparative picture is complicated because of advances in techniques which ensue from the introduction of new methods and devices largely for aerial exploratory work, Some of these methods were either in their infancy or unknown before World War II. Geological exploration may well be considered as a form of applied research. True, it has peculiarities from this standpoint some advantageous, others disadvantageous, Some of the advantages lie in the fact that exploration success does not involve the production of a new product which necessitates advertising expense and marketing problems. In normal times there is a well established market for the fruits of a successful mineral find. The outstanding disadvantage of exploration lies in the enigma of deciding when to quit if the sought fop prize is elusive. In the search for buried treasure, man?s curiosity is apt to color his judgment. Even the so-called detached scientist may fall 'all too readily into the wishful thinking of the old- time prospector who is lured on by the thought that the next pull from the drill hole, or the next round from the face will reveal a bonanza. It involves mature judgment and experience to ascertain the stage in exploration when further work is not justified.

Jan 1, 1958

By Mohammad R. Jafari

The Camp Dresser & McKee (CDM) has been retained by the Sacramento Regional County Sanitation District (SRCSD) to design the Mather Interceptor, a portion of the South Interceptor and Mather Interceptor program. The Mather Interceptor consists of 14,667 feet of 54 to 72 inch gravity interceptor. Approximately 90 percent of the alignment will be constructed via tunneling. Cobbles and boulders in a sand/gravel matrix dominate the ground conditions combined with seasonal perched groundwater table at some of the deeper reaches of the alignment, impacting design consideration. This paper will present the results of a comprehensive geotechnical investigation conducted for this project and in-depth technical evaluation of various trenchless techniques feasible for tunneling in the cobble and boulder laden formations of this project. This paper will also present the risks and issues of the design alternatives and selection criteria.