Search Documents

By Man-Chao He

One of the critical problems involved in deep coalmines is unusual gas emissions. Many researchers agree that there is a relationship between coal gas emissions and geological features such as tectonics or geological disturbances, gas content, properties of the coal and rock and the mininginduced stress state in the coal seam and rock. Thus, the present paper intends to investigate complex mechanical phenomena during the process of gas emission in underground coal-mines. A program of laboratory testing was undertaken to study the effects of temperature and pressure on mechanisms of gas emission. It must be noted that this paper describes new techniques developed to simultaneously measure deformation and gas pressure, as well as flux during the test, taking the characteristics of gas transport into consideration under certain temperature and pressure conditions. The results indicate that under certain temperature and pressure conditions, gases adsorbed to coal start to desorb, and increase the pore pressure. High pressure gases entering coal fractures can generate high tensile stresses near the crack tips, leading to crack propagation and coalescence, which in turn can cause the specimen to dilate. From the experimental viewpoint, these test results may help us discern why mining seismic events can trigger gas emissions.

Aug 1, 2013

By David A. Milligan

This paper describes the Darwin Silver Recovery project, located 66 km (40 miles) outside of Lone Pine, near Darwin, Inyo County, California. A lead-zinc mine and a flotation concentrator were operated there from 1945 to 1957. By the time the mine was shut down, 1.53 Tg (1.69 million short tons) of tailings had been stored in ponds. An average silver assay of 47 mg/kg (1.38 troy oz/st) of tailings stimulated interest for commercial silver recovery. A heap leach process was developed in 1981 at the Tucson Research Center of Anaconda Minerals Company, a division of Atlantic Richfield Company. Agglomeration techniques were used on the ore since the fine grind did not allow direct heap leaching. Lime and cement were required as binders, Early laboratory tests showed that recoveries equal to those from an agitated leach could be achieved at lower capital and operating costs. Laboratory tests determined cyanide requirements, lime and cement usages, and percolation or leach rates, as well as confirming that a zinc precipitation step could recover the silver from the leach solution.

Jan 1, 1983

By Pamela J. Watson

The U.S. Bureau of Mines has demonstrated in laboratory tests that drilling with surface-charge-neutralizing concentrations of polyethylene oxide (PEO) polymer solutions simultaneously improves penetration rates and extends bit life. The applicability of this additive to improve drilling performance in coal measure rocks was demonstrated under field conditions at an abandoned mine land site in Pennsylvania and a producing coal mine property in Ohio. Penetration rate improvements ranging from 15 to 50 pet were obtained when core drilling through a variety of coal measure lithologies. Drilling cost analysis indicates that the small added cost of using the polymer is more than offset by the savings that result from demonstrated increased drilling penetration rates, which translate into drilling cost savings of about 10 to 30 pct. This report also gives chemical analyses of a variety of coal measure rocks and some corresponding local drilling water samples, obtained from a wide geographical base, along with threshold concentrations of PEO required to effect the improved drilling performance in these rocks. From these data, the threshold PEO concentrations needed to ensure improved drilling performance can be estimated for any coal measure rock suite. Proper techniques for mixing PEO solutions are also presented.

Jan 1, 2010

By David P. Lindroth

The heat content above 25.0° C up to 1,000° C was measured for six rock types: St. Cloud Gray Granodiorite, Holston Limestone, Sioux Quartzite, Rockville Quartz Monzonite, Salem Limestone, and the basalt at Dresser, Wis. The calorimetric data were obtained with an isothermal jacket-copper block calorimeter. The experimental heat content data for each rock type are presented, along with specific heat data obtained from the temperature derivative of the heat content. For the six rock types the maximum deviations of the specific heats at a given temperature were within 10 percent below 575° C and within 34 percent above 5750°C. The increase in the values of specific heat range from a minimum of 13 percent for the basalt at Dresser, Wis. (temperature range, 100° to 1,000° C) to a maximum of 46 percent for Holston Limestone (temperature range, 100° to 870° C).

Jan 1, 1971

By J Millard, K Sexsmith

BHP Billiton Diamonds Inc (BHPB) has been mining kimberlite from several pipes at the Ekati Diamond MineTM located 300 km north of Yellowknife since 1997. Processing of kimberlite produces coarse kimberlite rejects (CKR, 0.5 to 8 mm) and fine tailings (less than 0.5 mm). The CKR are trucked to the Coarse Kimberlite Reject Storage Area (CKRSA) located within the drainage area of the tailings impoundment (Long Lake Containment Facility û LLCF). The coarse rejects are wet when dumped and are expected to freeze as a result of annual average site temperatures of about -10¦C. Seasonal thawing occurs along the exposed edges of the pile. Monitoring of the CKR indicates they have consistently low sulfur concentrations (0.4 per cent) accompanied by high acid neutralisation potentials (78 to 337 kg CaCO3/t). Carbonate concentrations vary from 0.9 per cent to 3.4 per cent. The CKR are therefore not potentially acid generating based on conventional laboratory testing. Monitoring of stagnant pools on the tundra downgradient of the CKRSA has shown that water originating from the pile resembles acid rock drainage (ARD). Water pHs can be less than 4, and sulfate concentrations are typically in the thousands of milligrams per litre. Conventional flowing toe seeps are pH neutral but also have elevated sulfate concentrations. Investigations conducted in the summer of 2002 revealed no evidence of in situ acid generation. Pore water chemistry is probably controlled by oxidation of fine-grained pyrite, neutralisation of acidity by calcium and magnesium carbonates and silicates, and freeze concentration of pore water. The acidity observed in tundra pools downgradient of the CKRSA appears to be a result of leaching and mobilisation of iron under reducing conditions at the CKR-soil contact. Downstream of the CKRSA, reduced iron oxidises and is hydrolysed on contact with the atmosphere causing pH depression. BHPB is applying the findings of this study by constructing facilities containing kimberlite on granite pads. These in turn are placed on frozen ground so that the foundations remain frozen and limits contact of wastes with the acidic soils.

Jan 1, 2003

By Ernest Stütz

(New York Meeting, October, 1918.) THE problem of increasing blast: furnace efficiency through diminution of flue-dust production while operating with burdens consisting largely of fine ores has of recent years attracted the attention of metallurgists, whether directly or indirectly interested in the economies of iron smelting, and the various methods evolved from theory or practice have been submitted to wide discussion. After the very thorough and, at that time, exhaustive view of the whole subject, which was afforded to the industry by the meeting of this Institute in February, 1912, the subject was again taken up at the meeting of the Verein deutscher Eisenhüttenleute at Diisseldorf in December, 1912. While American and German conditions are not entirely identical, it may be of interest to give here the words of the gentleman summing up the discussion at the Diisseldorf meeting: ' The chief advantage offered by the use of briquettes lies in the fact that disturbances in the furnace, caused mostly by the presence of fine ores in the burden, are avoided, and that blast pressure can be considerably reduced. The resulting economies cannot be overrated, as, with lower blast consumption per ton of product, the installation will be able to take care of increased production. In consequence of lower pressure and speed of blast, heat is more efficiently utilized, flue gas temperature is lowered, and coke particles are less liable to be carried along with the flue dust, of which considerably less is produced. Finally, by increased regularity of operation and higher . temperature in the lower parts of the furnace, the quality of the product is improved. The question of briquetting iron ores has grown to be one of the most important in the iron industry, and, it is not any more a question of what is the cost of briquetting ton of ore, but what, in using ore briquettes, is the cost of production of a ton of iron.'

Jan 7, 1913

By Reinaldo J. Villa, Joshua C. Adams

The I-395/SR-836/I-95 reconstruction project is an $818-million design-build construction effort that includes construction of viaduct, segmental and signature bridges in Miami leading into Miami Beach in Florida. Based on the load testing performed during the design phase, the design-build team determined that conventional driven pile and drilled shaft foundations were not feasible for support of segmental and signature bridges. Due to the weak limestone formation and successful use of auger cast-in-place (ACIP) piles in the Downtown Miami area on commercial developments, ACIP piles were selected as a foundation system to support bridges. This is the first time in history where the bridges will be supported by ACIP pile foundations in an interstate highway in the State of Florida. The design build-team worked closely with the Florida Department of Transportation to develop requirements for the load test program. The paper will provide an overview of the geotechnical data collected, results of dynamic/bi-directional load testing performed on test piles, data collected, installation of piles, and lessons learned. The load test program included a total of fifteen test piles with dynamic, bi-directional, and lateral load testing on 30 and 36-inch diameter ACIP piles and instrumented with thermal integrity profiling wires.

Sep 8, 2021

By J. Daavittila, P. Jokinen, M. Honkaniemi

In the latter part of the 1980?s Outokumpu Chrome in Tornio, Finland, was in a situation when its twenty-year-old ferrochrome plant was becoming inefficient to sustain economically sound production. The company made extensive studies on the then available processing methods to find out the best possible processing route. As a result the whole plant was practically rebuilt and expanded. When equipment was proven in practical operation an application for FeMn production was developed. Now when Tornio FeCr-plant is considering the expansion the same type of exercise is to be performed with today?s challenges, which will be discussed in the paper. These challenges include increasing costs or decreasing quality of raw materials, increasing energy costs, stricter environmental regulations and demand of better working conditions. The possibilities to respond to these challenges will be discussed in the paper. The future and continuing development with FeCr includes the better utilization of process dusts and a lower consumption of energy. By adapting the latest automation tools to better control of the process even higher efficiencies can be achieved with present technology. New processes are considered for development in the future and some possible technologies will be described.

Jan 1, 2004

By Patricio Barrios

In February 1996, ATLANTIC, COPPER completed the construction of a Project for Expansion and Environmental Improvements in its Smelter and Electrolytic Refinery located in Huelva. Following the expansion, the new operating concept is based on the simultaneous blowing of two converters, while increasing throughput in the Flash Furnace up to the level required to deliver matte to both converters. While the production level planned with the Project.(270,000 MTPY of copper from concentrates) was reached the following June, work since then has been carried out to optimize the new equipment .and to develop a new operating shedule. This paper describes operational experiences from the start up of the Expansion Project, difficulties encountered and operating improvements introduced, which have allow an increase of production levels up to 300,000 MTPY of copper.

Jan 1, 1998

By Phillip N. Yasnowsky

The thrust of this Bureau of Mines report is to relate the size of automobiles to the price of gasoline, and the use of minerals in automobile manufacture to the size of automobiles. Only one of the many plausible scenarios of public reaction to higher gasoline prices, a switch to economy size automobiles, is developed. No account is taken of other potential impacts such as improvements in public transportation or increased occupancy per vehicle. Furthermore, a gasoline price increase is the only incentive to the greater utilization of economy cars that is considered. A gasoline price increase to $0.60 per gallon would reduce the amount of minerals required to produce the automobiles sold in the United States by an estimated 15 percent. Gasoline prices of $0.80 and $1 per gallon would cause declines in mineral requirements for U.S. automobile sales estimated at 26 percent and 35 percent, respectively.

Jan 1, 1974

The underwater explosions have been used for several decades for the determination of energy content of explosives. This test method is the only one by which shock, fly rock and total energy can be measured separately. It enables to develop the energy content of explosives for different purposes; the military high explosives should contain more shock energy whereas the fly rock energy is very important feature for the blasting explosives. The purpose of this study was to establish a test place for the underwater experiments in an old water filled open pit, to estimate the repeatability of the energy measurements, to calculate the standard deviations and to compare the total energy content of commercial explosives to the theoretical values calculated by the thermo dynamical program. The test method seems to work quite well especially for the homogeneous explosives. The difference between the energy content of theoretically calculated and measured values for the homogeneous emulsion explosives was about -3% and for the dynamite about -5%. The energy difference for the unhomogeneous ANFO was detected to be -19%. The diameter of the charge was 15 cm and it was obviously too small for ANFO to detonate ideally. On the basis of the test results this test method seems to fit best for the cap sensitive, completely homogeneous, spherical charges whose masses are big enough and which are initiated from the centre of the charge. The underwater explosions as a test method is the only one which can separate shock, bubble and total energies from each other and therefore makes it possible to develop the properties of explosives for different purposes which is very important feature of this method.

Jan 1, 2005

By B Mack

The cost of water treatment is now more than ever a major consideration for maintaining an environmentally and economically sustainable mining operation. As an industry, we often have to consider water sources that are highly impure and difficult to treat. We are also discovering the value of our waste waters in this regard and using new and improved methods and technology to reclaim and reuse water. In many instances, the water or waste water to be treated is highly acidic and saturated in sparingly soluble salts. Conventional systems used to liberate this type of water typically involve high doses of lime with large volumes of waste sludge produced, and are comparatively complex to operate, to pretreat the water in order to reduce scaling tendency on the reverse osmosis stage. However, if the water is considered valuable for reuse, then why not avoid difficult and cumbersome pretreatment processes and treat the water at low pH to keep the sparingly soluble salts, metals and other dissolved species in solution. This paper describes a patented technology that uses and successfully proves this concept as a cost effective option for certain situations. Results from a treatability study on an Australian groundwater are discussed, along with an economic comparison to a conventional method and discussion on full-scale potential.

Jan 1, 2009

By Zhikai Wang, Wensheng Lyu, Peng Yang

"To better understand the mechanical behavior of the compression deformation of backfill under high stresses corresponding to large depths, consolidation compression tests were performed for cemented tailings backfill with a cement-sand ration of 1:10 and 30% water under confined conditions. After applying different loading stress functions from 0.5 MPa to 32 MPa, the final axial deformation of the test specimen of backfill was obtained, and the micromorphology of backfill was studied before and after consolidation by scanning electron microscopy. Additionally, fitting analysis was performed for backfill confined compression deformation data and device model constitutive equations by the minimum square law. The constitutive model was revised according to the analysis results. The research results indicate that, as the load increases, the void ratio e obeys the functional relationship e=alnt + b (where a and b are fitting constants and t is compression time). Under the high-stress conditions of confinement, the constitutive model of backfill consolidation and creep can be used to describe the creep behavior of the backfill. Under high-stress conditions, after the consolidation of the confined backfill, the space between the tailing particles diminishes, the particles becomes more compact, and particle slippage occurs. INTRODUCTION With the depletion of shallow mineral resources, the mining industry has gradually shifted to deep mining (Zhang, Li, An, and Huang, 2010). Furthermore, with the continuous introduction of sustainable development policies regarding development and utilization of mineral resources, the mining industry must protect the limited available land and make full use of mineral resources as much as possible (Sijing, 1994; Zhihua, 2009). Backfill mining technology offers an unparalleled advantage in fully recovering mineral resources, controlling pressures, and improving environmental protection. As a result, this method has been widely used in various countries in the world (Burd, 2002; Benzaazoua, et al., 2008). Of the underground mines in the world, 45% of the large and medium-sized non-ferrous-metal mines and 37% of the gold mines use backfilling (Fuhrman, et al., 2014; Khaldoun, Ouadif, Baba, and Bahi, 2016). In addition, 45% of underground non-ferrous-metal mines and 37% of the gold mines use the filling method (Mchaina, Januszewski, and Hallam, 2001). According to incomplete statistics, more than 80 metal mines operate at a depth of more than 1 km; the depths of several typical deep mines are shown in Figure 1 (Burd, 2002; Fall, et al., 2009)."

Jan 1, 2017

By J R. O Walli

Large production shafts can be successfully sunk through the ubiquitous Blairmore formation of southern Saskatchewan by employing the freezing process and by the installation of a cast iron tubbing lining. Although the freezing technique for shaft sinking and the use of cast iron tubbing to preserve the shaft are new to the North American continent, these procedures have been employed in Europe for the past eighty years. More than 200 shafts, covering a wide variety of ground conditions, have been sunk by the freezing process, and most of these have been lined with cast iron tubbing. The No. 1 shaft of International Minerals and Chemical Corporation, near Esterhazy, Saskatchewan, comprises the first major example in Canada of the employment of European methods to overcome extremely difficult ground conditions. The Blairmore formation was solidified by the deep freezing process, employing a lithium chloride solution as the refrigerant, with input temperatures ranging to -55°F

Jan 1, 1964

By Luis Amendola

El presente texto señala el proceso de diagnóstico e implementación de gestión de activos físicos en la producción de las operaciones mineras para aumentar su capacidad, al tiempo que elimina las pérdidas y aumenta la eficiencia en las operaciones. Para ello, se utilizó la metodología 3P+ PAM, donde se establece un punto de partida de forma científica y de negocio para definir cuáles serán las acciones que se deben ejecutar para alcanzar la meta y las buenas prácticas en la gestión de activos físicos de la empresa.

Sep 1, 2014

By L. C. IlsLey, R. A. Kearns

"The electrical section of the Bureau of Mines has obtained copies of all available State safety rules and regulations in order to make a study of those portions of the codes relating to electrical equipment. While it has been found almost impossible to compare the several codes as a whole, comparison of those regulations dealing with a single subject has proved both interesting and instructive.Sixteen states have rules or enactments having reference to telephones and the present paper covers a compilation of these references. It is believed that data of this kind will be of service to commissions or other bodies contemplating the revision of existing codes.The compilation taken from the various codes follows: State Rules and Regulations.California.Sec. 5 (Par. c) Telephone communication shall be maintained between a co-operative station and each mine which it supplies. If the foreman in charge of a station does not reside thereat, his residence also shall be in telephone communication with each mine supplied by his station.Sec. 8 (Par. a) Whenever a fatal accident occurs in or about any mine, notice thereof shall be given promptly by telephone or telegraph if possible, followed by a notice in writing to the chief inspector, by the superintendent or other person having immediate charge of the work at the time of the accident."

Jun 1, 1921

By J. E. McGill

The junior and small-scale mining sectors in South Africa play an important role in the livelihoods of numerous communities. Mining presents an opportunity, in the post-1994 democratic era, for many individuals to obtain access to much required empowerment and socio-economic development. These sectors are, however, not without numerous characteristics that pose problems for operators, legislators, and other role-players. Mining is inherently risky, with operators experiencing frequent difficulties and challenges throughout the life of mine. Opportunity exists, and needs to be enhanced, for junior and small-scale prospects and operations to include technical risk assessment techniques in documentation presented in search for funding, and in optimizing monthly planning and longer-term functioning. The focus here is to explore how the risk management cycle may currently be applied to a mineral resource suitable for exploitation by the junior and small-scale mining sectors. No management process can create additional value in the ground, but various available mechanisms can go a long way to quantifying the inherent risk that exists, highlighting the need to manage the risks and hopefully allowing the entrepreneur access to the intrinsic opportunities of the emerging mining sector in South Africa.

Jan 1, 2006

By J F. H Thompson

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Mineral exploration and mining are challenging businesses. Remote and at times harsh conditions have always made it difficult for exploration, but modern explorers also have to deal with cover, numerous technologies, an explosion of data and critical early community engagement. Mining deals with the reality of moving and breaking thousands of tonnes of rock each day to extract what can be a very minor component of economic value, and, furthermore, society expects that this will be done in a clean and sustainable manner. The exploration and mining challenges appear disparate, but they are intimately related.Although not widely appreciated, both exploration and mining have a long tradition of innovation. Over the last 50 years, major step changes in exploration have resulted from radical advances in our understanding of ore forming processes, new geophysical, geochemical and remote sensing technologies, and new ways to integrate and interrogate data. Over a more extended period, close to 100 years, mining has developed bulk surface and underground methods, selective extraction through flotation and leaching and global positioning system–geographic information system control systems that collectively facilitate mining at a massive scale. And yet, in spite of these successes and the boom that we have enjoyed in the last ten years, the industry is under pressure and the need for innovation and change is paramount.The major drivers for innovation are the need for increased quality in discoveries and mines and the need to interact effectively with communities and jurisdictions such that the benefits of quality mines are recognised and enjoyed widely.We are still making new discoveries around the Pacific Rim and elsewhere, but many argue that the quality – grade and accessibility – of these discoveries is decreasing. The net result is that explorers are delivering resources and reserves for development at lower grades and with higher capital and operating costs than current operations. For mining, the increasing age of many existing operations contributes to increasing costs, which, when combined with decreasing cut-offs and lower grades, also results in declining quality. The combined picture does not look good.Just as the pressure to improve performance and margins in the face of declining inputs increases, we are simultaneously faced with increasing societal demands for improved environmental performance and sustainable practices. This is most apparent at the local, community level, where opposition ultimately leads to delays or even cancellation of new projects. Quality is again the issue – quality of the initial and ongoing engagement and quality of the proposed mine in terms of environmental and economic performance.CITATION:Thompson, J F H, 2015. Exploration and mining – the need for innovation , in Proceedings PACRIM 2015 Congress, pp 45–48 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Donald E. Grimes

In conjunction with Inland Steel&apos;s development of lead-bearing steels possessing improved machin-ability because of tellurium and/or selenium additions, it was decided to determine liquidus and solidus temperatures in the Pb-PbTe-PbSe sub-ternary system. With the exception of alloys in the PbTe-PbSe system, it is believed that no previous study of this subternary has been performed. Thermal analysis was employed in a general survey of the subternary. In addition to PbTe, PbSe, and pure lead, ten ternary compositions were selected at intervals of ten at. pct. Sixty-gram alloys were prepared by sealing an appropriate mixture of the elements in quartz crucibles with a central thermocouple-well under a vacuum of less than 10 p. All three elements were 99.999+ pct pure with only trace impurities detected by spectroscopic examination. After the alloys had been heated at least 20°C above the liquidus in a Kanthal furnace, cooling and heating curves were obtained. Two or more cooling curves were employed both for the determination of each alloy liquidus and for the solidus of those al- loys containing greater than 50 at. pct Pb. Cooling rates were 0.5° to 3.5°C per min during the 5 min immediately prior to the start or end of solidification. For those ternary alloys containing 50 at. pct Pb, the solidus was determined from heating curves. Temperatures were measured with a Pt/Pt-10 pct Rh thermocouple which was calibrated in the same apparatus against the freezing points of zinc (A. D. MacKay—99.999 pct), antimony (A. D. MacKay-99.999 pct), and copper (ASARCO—99.999+ pct) both before and after the experimentation. The only interruptions in the continuous strip-chart recording of the temperature occurred for brief periods at significant points of interest when direct readings were made with a Rubicon Type B potentiometer sensitive to * 1 µv. The average liquidus and solidus temperatures obtained in this investigation are listed in Table I together with probable errors based on the accuracy of the thermocouple calibration and the reproduci-bility of the data. No chemical analyses of the alloys were performed because the synthetic or as-charged compositions were felt to be reliable. The melting points obtained for PbTe (924.7° ± 0.7°C) and PbSe (1084.0° ± 0.6°C) compare favorably with recent findings of other investigators.&apos;-&apos; As indicated in Table I, both the liquidus and solidus temperatures increase as selenium replaces tellurium for a constant atomic percent lead. As a result, the ternary liquidus and solidus temperatures for a given percent lead lie between the corresponding binary temperatures published in the literature. It should be noted that those ternary alloys containing 50 at. pct Pb exhibit a relatively narrow liquid-plus-solid region (<80°C) when compared with alloys containing greater than 50 at. pct Pb. Alloys with 60, 70, or 80 at. pct Pb not only have a much wider liquid-plus-solid region (>500°C) but also exhibit considerably lower and approximately constant solidus temperatures which thus form a virtually isothermal solidus "plane" slightly below the melting point of pure lead (327.3°C). For these alloys

Jan 1, 1965

By E. L. Sweeney

The mine and mill of the Davis-Dunkirk Lines, Inc., are about 16 miles by road south of Prescott, Ariz., which is the nearest railroad point for receiving mine and mill supplies and for shipping concentrates to smelters. A good trucking road reaches within 2 miles off the property, but from that point the grade is very steep. Outgoing loads are limited to 2 tons. The topography near the mine is exceedingly rugged, and the area is slightly wooded. The climate is mild excepting in a few winter months, when the snowfall is heavy. Electric power is secured by way of a 4 1/2-mile, high-tension line connecting with the main line of the Arizona Power Co. The concentrator was intended to treat 60 tons or more daily of gold-silver-copper ore and make a single gold-silver-copper concentrate for shipment to a copper smelter.

Jan 1, 1933