Search Documents

By A. J. Forney

This report summarizes the findings of methods of treating caking coals in a fluid bed to destroy their caking properties. In batch tests it was found that several coals, including those with a free-swelling index greater than 8, could be decaed at temperatures from 400° to 425° C with a fluidizing gas composed of inert gas or steam containing 0.2 percent oxygen and a minimum residence LS,-;,' of 5 minutes. When treatment decreased the free-swelling index from about 8 to 1-1/2 or lower, the resulting treated coal was noncaking. In a continuous unit with continuous feed and discharge of coal, slightly more severe conditions were required to decake the coal. For 18- to 100-mesh coal a temperature of 430° to 440° C and an oxygen-to coal ratio of 0.4 cubic foot of oxygen per pound of coal feed was necessary. Finer mesh sizes required lower oxygen-to-coal ratios. In tests using air only as the fluidizing medium and treatment temperatures well below the softening range, the caking properties of 150- to 200-mesh coal were destroyed in 30 to 40 minutes of residence time at 200° C. Coarser sizes of 18 to 48, 48 to 100, and 100 to 150 mesh required longer residence time.

Jan 1, 1966

By H. A. Wentworth

The Central Manitoba mining district, as spoken of in Manitoba, refers to that portion of the country lying between lake Winnipeg on the west and the Ontario boundary on the east, and from a few miles north of the Wanipigow (or Hole) river on the north, to a few miles south of the Bird river. It embraces two known mineralized belts; the gold area in the north, extending from the shores of lake Winnipeg almost to the Ontario boundary (in a slightly southeasterly direction) a zone some eight or ten miles wide and perhaps forty miles long, lying (for the most part) north, and parallel to, the Manigotagan river; and the Bird river copper and coppernickel deposits, an area not yet clearly defined, but in general lying immediately north of, and roughly parallel to, the Bird river. To the south of the Bird river is a somewhat differently mineralized area, numerous pegmatite dykes being found, with minerals typically associated with such rocks. More specifically, the known gold deposits are largely segregated in the above belt; (1) around English brook; (2) along the north shore of Wanipigow lake; the Rice lake area (about midway of the belt); and the Long Lake-Bulldog lake area, at the eastern end of the belt. Not all the known gold occurences are found in these segregations, but the density of claim staking in these areas is perhaps an indication of the greater number of prospects found in them to date.

Jan 1, 1925

By J. P. Sheeha, W. F. Craig, M. Baeyertz

The loss in toughness caused by phosphorus within commercial ranges was studied in AISI-SAE 1340 steel and in molybdenum modifications of this grade. The replacement of part of the manganese by molybdenum in amounts which maintain the hardenability of the standard 1340 grade was shown to counteract to a marked degree the detrimental effects of phosphorus. THIS paper deals with the effect of phosphorus on the toughness of 1340 steel and with the effect on toughness of replacing part of the manganese by molybdenum while retaining the same hardenability as that of 1340. In previous work1 a progressive decrease in toughness was observed when the phosphorus content of 5140 was raised from 0.020 to 0.036 pct; that is, from a moderate phosphorus level to one higher but yet within the AISI-SAE specification for this grade. The structural condition of the steel was tempered martensite. Toughness was evaluated by the transition temperature determined by V-notch Charpy tests. Replacement of a part of the chromium in 5140 by molybdenum provided a factor of safety against loss of toughness caused by phosphorus, especially where the steel was cooled slowly after tempering. Scope of the Study: In view of the improved tolerance for phosphorus obtained by replacing a part of the chromium in 5140 with molybdenum, it seemed desirable to investigate the possibility of obtaining similar improvement in 1340 by replacing part of the manganese with molybdenum. Heats were made at different phosphorus levels, in a series that began with 1340 and ended with steels containing 0.32 to 0.35 pct Mo with 0.82 and 0.90 pct Mn. The analyses of the heats are given in table I. In order to facilitate later discussion, the 1340 heats have been placed together in the order of increasing phosphorus content, and the molybdenum modifications have been grouped according to phosphorus

Jan 1, 1951

By T. G. Sitharam, Resmi Sebastian

"Wave propagation studies across jointed rocks have significance in the fields of rock mechanics and geophysics. The passage of a seismic wave induces strains in rocks and often, these strains are of low magnitudes except at the vicinity of source. These low magnitude strains are generally in the elastic range and hence elastic constants necessary for the design and analysis of strength of rock mass, can be derived from wave velocities. Measurement of travel time velocities and measurement of resonance frequencies are the two methods usually adopted for obtaining wave propagation velocities.Resonant column apparatus measures wave velocities from the resonant frequencies obtained during testing. Depending on the type vibration applied, torsional or flexural, shear and compression wave velocities are secured. By varying the amplitude of vibrations applied, various strain levels can be introduced and corresponding resonant frequencies and wave velocities can be calculated. The resonant column experiments were performed on a model material, hardened Plaster of Paris (POP) samples, in laboratory. The paper explains the preparation of samples and the working mechanism of resonant column apparatus along with the estimation of wave velocity from resonant frequency. The numerical simulation of resonant column apparatus using distinct element method and its validation with the experimental results are presented in the paper.A distinct element code is usually used to simulate the movement of materials with intersecting discontinuities. Finite rotations and displacements of individual blocks representing the material are permitted and new contacts between the blocks are identified as the calculation progresses. Three dimensional Distinct Element Code (3DEC), the software intended for the numerical simulation of rock engineering projects, can well simulate the behavior of jointed rocks under static and dynamic loading conditions. The numerical simulation of resonant column apparatus has been performed with 3DEC considering its efficiency in modeling jointed rocks.The numerical modeling of the resonant column apparatus with application of torsional and flexural vibrations to the sample is elaborated in the paper. The response of samples to a range of frequencies is obtained and the frequency that induces maximum displacement in the sample is measured as the resonant frequency, for any particular strain level. The displacements measured at various points of the sample during application of vibrations are compared and presented. The numerical modeling of resonant column apparatus with an intact sample (without joint) and a sample with a joint incorporated are explained at a particular strain level. The resonant frequencies obtained from laboratory experiments and numerical simulations are compared and illustrated. It has been found that resonant frequencies obtained using numerical and laboratory experiments are in good comparison and can be extended for various strain levels and sample conditions."

Jan 1, 2015

By Keith Maki

This paper details a simple substitution of precise electronic timing in the holes for standard pyrotechnic delays. In addition, we wanted to use two electronics in bottom and top to test the colliding shock wave theory. It also discusses the difficult loading conditions on the Iron Range of Northern Minnesota. No preliminary analysis (Signature Hole waveform analysis) was done to determine the most favorable blast timing for fragmentation increase or vibration reduction.

Jan 1, 2007

By D. S. Richards

Computers have revolutionized the collection of data on modern mines. Never before has it been possible to collect data from all aspects of the mining value chain at rates now common. With this has come a new challenge. Deriving information from these copious amounts of data and disseminating it. This problem is being exacerbated by technical software systems, which use proprietary and binary data formats that severely inhibit the flow of data and information both across departments and the larger organization. Generally this had led to data duplication and data redundancy. The Gemcom Enterprise Mining System (GEMS) makes use of industry standard, secure and open databases for all its data objects. It manages multiple users accessing the same bits and bytes in the database, preventing data duplication and redundancy. Developed in the Microsoft BackOffice ® environment, GEMS is also able to leverage the enormous amount of tools available in this environment, whether it’s for e-mail notification, reporting or data capture. Microsoft’s® Active Server Pages are one of these tools. These are standards used to create dynamic and interactive web pages with links into databases and many other objects. The real example outlined in the text, demonstrates how a user anywhere in the world is able to login to a web page and run a query that returns a report with vector plots of performance for the user-selected time frame. As integration is tightened between the various components of the mining value chain, the importance and reliance on ASP pages will grow as the need for management information tools develops. Keywords: mines, computers, ASP, GEMS, integration, Microsoft, Management Information.

Jan 1, 2003

By E. A. Thiers

The causes of structural changes in the markets for high technology alloying metals are discussed in terms of technological, economic, and financial trends. Recent market imbalances have affected producers in developed and developing countries differently. Possible response strategies for suppliers in the two types of countries are examined that may alleviate future market imbalances.

Jan 1, 1988

By Townsend. James W.

"INTRODUCTION As a byproduct of its mineral investigation program, the Bureau of Mines has developed a number of operating devices and techniques worthy of note. This paper, prepared under the direct supervision of Paul T. Allsman, chief, Salt Lake City Division, Branch, and under the general supervision of Lowell B. Moon, chief, Mining Branch, reports upon one such device. A simple device has been developed for measuring angles of deviation from the horizontal as recorded on a glass tube by acid etching. The device has facilities, also, for measuring the angle between the long axis of the ellipse and the north-south reference points established by a Maas compass or from an established axial lamina, on the tube, which was ori¬ented to a specific direction in the hole by rod alinement.The device was found accurate within half a degree on repeated orientations of the same tube. However, the degree of accuracy is dependent on the accuracy of personal manipulation in orienting the tube to the correct plane."

May 1, 1947

By J. A. Eisele

The Bureau of Mines has reviewed the literature related to the recovery of A1203 (alumina) from coal ash. A small amount of unpublished data is also reported. Of the processes studied, the alkaline-sinter process is the most promising from a technical standpoint. However, owing to the high cost of processing coal ash, the dispersed location of powerplants, and the domestic availability of higher grade alternate materials, coal ash does not rank as a primary source material for replacing imported bauxite.

Jan 1, 1979

By John Marsden, Mike Botz

A variety of modeling techniques can be utilized to forecast metal production at heap leaching operations. These approaches reflect a wide range of complexity, flexibility, time to implement, cost, and accuracy. For many operators, a spreadsheet-based modeling technique is attractive since the calculations are directly accessible, models can often be developed by site staff, and the results are generally easy to extract and interpret. The authors have developed a spreadsheet-based modeling technique that provides a high degree of flexibility, while still considering detailed operating information for ore properties, leach kinetics, scaleup factors, lift height, and in-heap metal inventories. The technique involves establishing kinetic leach curves for each ore type to characterize metal extractions, followed by application of separate metal recovery curves to define the rate at which leached metals exit the heap in pregnant solution, taking into account delays due to the in-heap solution inventory. At any point in time, the difference between total metal extracted and total metal recovered is equal to the in-heap inventory of the leached metal. This modeling technique is particularly useful for larger multi-lift heaps where delays in metal recovery are appreciable due to in-heap solution holdup. The technique is also applicable to sites with multiple heaps, leach cycles, and/or metal recovery plants (e.g., carbon columns for gold; solvent extraction for copper). This paper describes the modeling technique, including input data required and methods for defining kinetic leach curves and metal recovery curves. The technique is compared against an alternative spreadsheet technique using a simplified in-heap solution inventory calculation to forecast metal production, which has proven to be effective at a number of sites.

By M. Cai

A practical simple method is proposed to estimate the tensile strength (st) of strong brittle rocks from the strength ratio of R= sc/st = 8 sc/sci, where sc is the uniaxial compressive strength and sci is the crack initiation stress in an uniaxial compression test. 8 is the Griffith strength ratio and the term sc/sci accounts for the difference of crack growth or propagation in tension and compression in uniaxial compression tests. sci can be reliably obtained from volumetric strain measurement or acoustic emission (AE) monitoring. With the strength ratio R determined, the tensile strength can be indirectly obtained from the result of uniaxial compression tests. In addition, a practical estimate of the Hoek-Brown strength parameter mi is presented and it is suggested that mi = 12 sc/sci can be applied to strong, brittle rocks in high confinement zone and mi = 8 sc/sci can be applied to low confinement to tension zones. It is found that the predicted tensile strengths and Hoek-Brown strength parameter mi using this method are in good agreement with test data. The rock strength parameters like st and mi, which require specialty tests such as direct tensile (or Brazilian) and triaxial compression tests for their determination, can be reasonably estimated from uniaxial compression tests.

May 1, 2009

By Robert M. von Storch

Chairman Doc, distinguished guests, and fellow members of the Rocky Mountain Coal Mining Institute: It's a genuine pleasure to meet with you again at the 54th regular meeting. I might add that it is always pleasant to be at the top of the batting order. The field is wide open since there is no danger of repeating something already said. At the same time, I am aware that the lead-off speaker has a responsibility to avoid stepping on the toes of subsequent speakers. I promise to confine my remarks to areas other than those to be covered by the well qualified speakers that follow. During our meetings at this convention, many fine papers will be presented. Our thanks are due Bob Williams and his hard working program committee for the superior selling that brought so many eminent speakers to our meeting. And, of course, our special thanks go to Doc Schloss, general chairman of this meeting. Doc and his able colleague, Stan Shubart, have been the spark plugs that fired up all of the arrangements we are enjoying here in Glenwood Springs. I'm sure all of us are appreciative of the many hours Doc has devoted to seeing that our meetings will be pleasant and profitable. When we mention arrangements, we always think of that master arranger, Fred Whiteside, who, as a charter member and secretary-treasurer of the Rocky Mountain Coal Mining Institute, has had more to do with more matters around these parts than just about anyone I can think of.

Jan 1, 1958

By Kazuyuki Kikuta

MMAJ, a govemmental organization in Japan, has carried out a 4 year project for the development of the decontamination and metals recovering technology for the fly ashes from municipal waste incineration. Heavy metals (zinc, lead and copper) are recovered as raw materials for the non-ferrous metals production, without formation of any waste materials to be disposed. More than 500 thousands tonnes a year of fly ashes generation from the municipal waste incineration has been one of the main social issues in Japan, because most of them need to be disposed to the registered areas after decontamination, and occupy 5% of the municipal wastes disposed. The segregation, flotation and chemical process are applied to the treatment of the primary fly ash from municipal waste incineration, and MF (Mitsui-type blast furnace) Process after the chlorine removal to the secondary fly ash. The main results of experiments are -About 90% of heavy metals, zinc, lead and copper, can be recovered from the primary and the secondary fly ashes to the products for the non-ferrous metals production. -Both of the leaching residue from the primary fly ash treatment and the slag from the secondary fly ash treatment can be used as a raw material for the cement production, meaning that the decontamination technology for the ashes without the landfill has been established. -Dioxins in the primary ash can be decomposed satisfactorily, and the dioxins content in the segregation furnace gas is less than O.lng-TEQ/Nm3 without any gas cleaning system

Jan 1, 2003

By Roy C. Bartholomae, Jeffrey Shawn Peterson

1. INTRODUCTION In the early 1980s, the U.S. Department of the Interior’s Bureau of Mines Pittsburgh Research Center required that a large reverberation acoustic facility be constructed. This facility was designed to determine the sound power level emissions of mining equipment, especially continuous miners and jumbo drills. A contract for a conceptual design of a reverberation chamber was awarded to Wyle Laboratories of Huntsville, AL, which had extensive experience in the design, construction, and accreditation of acoustical reverberation chambers. The following standards were referenced as guidelines for the design of the chamber: ANSI S1.31-1980, “Precision Methods for the Determination of Sound Power Levels of Broadband Noise Sources in Reverberation Rooms” and ANSI S1.32-1980: “Precision Methods for the Determination of Sound Power Levels of Discrete-Frequency and Narrowband Noise Sources in Reverberation Rooms.” Specific requested criteria included that the room be large enough to accommodate typically large mining equipment and that there be adequate acoustical modal density in the frequency range of interest. It was also required that the room dimensions would support broadband acoustical measurements down to the 100 Hz third octave band. With the closing of the Bureau of Mines in 1996, this reverberation chamber lay dormant for a number of years. However, this facility is now part of the National Institute for Occupational Safety and Health’s (NIOSH’s) Pittsburgh Research Laboratory (PRL). One of NIOSH’s missions is to decrease noise induced hearing loss among the nation’s mineworkers. To this end, PRL researchers are refurbishing and instrumenting this reverberation chamber to facilitate assessment of the various engineering controls being developed to decrease the sound power level emissions of mining equipment. Early on, this work has sought to bring the chamber up to the level of ISO 3743-21 standard for engineering grade measurements for broad-band noise, with a longer range goal of improving the lab to meet the requirements of ISO 37412standard for broadband precision grade measurements. 2. DESIGN OF THE REVERBERATION CHAMBER The nominal room dimensions are 18.3 meters long by 10.3 meters wide with a height of 6.7 meters. The chamber volume is 1,286 cubic meters. These dimensions are important, as few reverberation facilities are large enough to test typically huge mining equipment. The floor is poured concrete with a sealer to make it acoustically reflective. The walls are built of hollow concrete block, 16 inches long x 8 inches high by 12inches thick. Each block has two hollow cores. The hollow block cores were completely filled with concrete with horizontal and vertical steel reinforcing bars 16 inches on center. This was done to supply a

By AIME AIME

MESSRS. BURT and Shockley and others have been for three years urging upon the Institute the matter of simplified spelling. The Institute endeavors to be progressive in the matter of spelling and. is in cooperation with the national body which has this in hand and which has its principal office in New York. Our spellings are changed as fast as-good usage will permit (so it seems to the Board of Directors) and the national body, which is the real representative of the simplified spelling interests, deems that the Institute is making real progress, although not quite as fast as extremists would wish. In January, 1919, Mr. Shockley sent out letter ballots which created a misconception in the minds of many members, who received the impression that the communications came from the Institute instead of from a small group of members. As a result of this propaganda 163 proposal-ballots were sent in to the Institute divided as follows: Yes ?114 No ?20 Negative letters ?9 Split ballots ?20 Total ?163 The total membership at this time was about 7200. The disgusted members would not vote.

Jan 1, 1920

By W. R. Hibbard

Emerging from discussions of U.S. energy policy: from the Project Independence Blueprint; from President Ford's statements to Congress; and from several independent appraisals of the situation; there is a clear objective to achieve an appropriate balance of supply and demand in the near term future (1) by developing more efficient ways of using energy and (2) by extending domestic sources of energy. More specifically, the strategy for achieving this goal has three parts (1) Conservation of energy through greater efficiencies in automobiles, appliances, lighting, heating, and industrial processes. (2) Increased domestic production of oil and gas through new sources such as the outer continental shelf and new efficiencies such as tertiary recovery. (3) Substitution of coal and uranium for oil and gas in utility power plants and industrial heating. The goal of energy research and development is to help achieve these goals and to help minimize the economic, environmental and social impact of our shift from imported energy to domestic sources. The focus of this paper is the implications of the expanded use of coal, and the research and development which may help achieve the above goals in so far as coal is concerned.

Jan 1, 1975

By S. Sunkavalli

Acid rock drainage (ARD) is produced when sulfides are exposed to oxygen and water. Oxidation reactions typically result in a depression of pH and leaching of solutes and metals. Many oxidation models have been developed based on oxygen diffusion, but in environments with high permeability, other transport processes (i.e., convection and advection) can play an important role. Multiple sulfide mineral phases with differing oxidation rates should also be incorporated. WROC, a finite-difference model, was developed to account for these factors in predicting ARD. The program includes sulfide mineral oxidation using a shrinking core mechanism, heat transfer by conduction, heat of reaction, and oxygen transport by diffusion and advection. The model was validated using data from the literature. After validation, the WROC model was used to simulate several different waste rock scenarios including different forms of sulfide mineralization and the effect of implementing a waste rock cover. The results demonstrate that including specific sulfide mineral phases can have a significant effect on oxidation and that implementation of a cover can also aid in reducing waste rock oxidation. Key words: Arsenic sulfides, oxidation, shrinking core, waste rock, oxygen transport

Feb 27, 2013

By B. W. Zhao

Quantitative analysis of minerals composing in ore is primary in process mineralogy, a veracious quantification and analysis is very crucial to optimize or design a beneficiation process, especially for a low grade and complicated ore. This paper will discuss a SEM-EDS based quantitative analysis developed in JKtech Australia through an example from Jinchuan lean ore. For a low grade, com-plex intergrowths and texture lean ore, chemical phase analysis of value minerals and identification by optical microscope are very essential, unite the SEM-EDS based quantitative analysis, we can understand exactly the lean ore, explain and quantify the process performance.

Jan 1, 2014

By Samuel Hoyt

SOME of the more important properties of finished materials are strength, ductility, toughness, resistance to alternating and repeated stresses, etc: Of these, the property that appears to have received the least consideration, at least in this country, is toughness, which is clue, possibly, to our regarding toughness as a qualitative property or, at any rate, as one that, parallels ductility. This arises out of our greater experience with the simple carbon steels in the rolled or forged (non-heat-treated) condition which, qualitatively, are tough if ductile and are not tough if brittle. In this way we have erroneously become, accustomed to judging the toughness of a material from its behavior in the tensile or similar test. The point of view presented in the present paper is that toughness, like hardness or tensile strength, should be regarded as an independent property and of sufficient importance to require, in so far as that may be possible, quantitative determinations. If such be true, it becomes at once necessary to devise experimental means for measuring, or valuating toughness, and the notched-bar impact test (the Charpy test) is advanced as the most logical test that has so far been developed for this purpose. It is further advanced, with particular emphasis, that we have two kinds of toughness to deal with and, accordingly, they will be dealt with independently. CLASSIFICATION OF MATERIALS ACCORDING TO TOUGHNESS Toughness has been defined somewhat as follows: Tough materials are those that offer considerable resistance to permanent deformation but which, once such resistance has been overcome, may' be deformed plastically, but only by the expenditure of considerable energy. In other words; tough materials may be deformed plastically but they absorb a considerable amount of work in the process. This kind of toughness may be called "static" toughness when the rate of loading is reasonably slow or "dynamic" toughness when the rate of loading is

Jan 2, 1919

By George Burgess

THE Pyrometer Committee was. formed Sept. 20, 1918, at the suggestion of Dr. H. M. Howe, Chairman of the Engineering Division of the Research Council, for the purpose of developing a pyrometric method suitable for open-hearth steel practice so that the effects of temperature in the various stages of the processes of steel making might be correlated quantitatively with the other factors influencing the production of sound .steel. As finally constituted the Committee consists of Dr. George K. Burgess, Chief Division of Metallurgy, Bureau of Standards, Chairman. Dr. Paul D. Foote, Chief of Pyrometry Section, Bureau of Standards, Secretary. Dr. H. M. Howe, Chairman Engineering Division, National Research Council, ex officio. Prof. G. H. Clevenger, Chairman Metallurgical Section, National Research Council, ex officio. Mr. F. E. Bash, Leeds & Northrup Co., Philadelphia, Pa. Mr. R. P. Brown, The Brown Instrument Co., Philadelphia, Pa. Prof. G. H. Brown, Rutgers College, New Brunswick, N. J. Mr. R. C. Drinker, metallurgical engineer, Boston, Mass., Dr. W. E. Forsythe, Nela Research Laboratory, Cleveland, Ohio. Mr. J. T. Hall, Taylor-Wharton Iron & Steel Co., High Bridge, N. J. Mr. J. S. McDowell, Harbison-Walker Refractories Co., Pittsburgh, Pa. Mr. Malcolm McNaughton, Joseph Dixon Crucible Co., Jersey City, N. J. Mr. A.' H. Miller, Midvale Steel Co., Philadelphia, Pa. Mr. F. E. Walduck (since deceased), The Norton Co., Worcester, Mass.

Jan 9, 1919