Search Documents

By E. J. Marcotte

"INTRODUCTIONThe Upper Canada Mine is located at Dobie, approximately ten miles east of Kirkland Lake, Ontario.The mill contains Upper Canada's cyanide circuit and Upper Beaver's flotation circuit. The combined capacity is 590 tons per day consisting of 415 t.p.d. of Upper Canada gold ore and 175 t.p.d. of Upper Beaver copper-gold ore.The Upper Beaver ore is trucked five miles to the Upper Canada mine site.Crushing:The crushing circuit consists of primary, secondary and tertiary crushing employing one C .A. C. 15 in. x 24 in. Superior jaw crusher, one 4 ft. x 8 ft. Tyler-Niagara double deck screen, one 3 ft. Symons standard cone crusher and one 3 ft. Symons shorthead cone crusher.The -2 in. product from the jaw crusher is fed to the double deck screen. The+ 5/ 8 in. passes over the top deck to the 3 ft. standard cone crusher; the+ 3/ 16 in. material passes over the lower deck to the shorthead cone crusher. The - 3 / 16 in. material pas sing through the lower deck of screens is the product to the mill.The screens used prior to the installation of rubber screen cloths were: one 4 ft. x 4 ft. section with 3/ 4 in. square openings and one 4 ft. x 4 ft. section with 5/ 8 in. square openings on the top deck; two 4 ft. x 4 ft. sections with openings of 3/16 in. x 4 1/2 in. slot on the lower deck. The fine screens were positioned so that the 4 1/ 2 in. slots were parallel to the flow of feed.The crushing circuit is operated on a three shift per day basis by one operator per shift."

Jan 1, 1968

By I. A. Kovalevska

Considered problems: elaboration and implementation of resource-saving technologies, low-cost support systems improvement, openings security and support, based on wallrock condition control with supreme implication into the rock pressure occurrence counteraction work. Results of analytic and underground investigations using computer simulation of the finite elements in order to calculate stressstrain state of the multivariable geomechanical systems are presented. Solutions of concrete objectives are found using spatial geomechanical model of solid motion around openings, considering real geomechanical parameters formation of support forms with proper conditions of their contact and real mechanical characteristics. Ultimate solutions of resource-saving technologies implementation based on the analysis of multivariate vertical, horizontal, and reduced stresses components calculation and also near-contour rock, support bearing components and security constructions movements are found. Results of experimental investigations of combined supports and security constructions, which increase openings' stability in difficult conditions of flat coal seams are presented.

Aug 1, 2013

By Aris Tambunan, Nella Lubis, Nurafrianti Saala, Komang Widhiayanto, Herry Saputra, Rudolf Sitorus

Maximizing mining recovery rates and minimizing ore loss are pivotal objectives for economic efficiency and operational effectiveness. This study explores methods to address these imperatives by enhancing ore production and recovery through improved blasting techniques and spillage control in the Martabe Gold Mine Project in North Sumatra Province, Indonesia. Between 2018 and 2021, the average mining recovery rate stood at 93%, resulting in a potential annual ore loss of 7% and a potential quarterly financial impact of close to $2 million. Maintaining and enhancing mining recovery became crucial, with a planned 30% increase in total material movement for 2022. The mining recovery target for 2022 was set at 96% based on best achievement historical data from 2021 to increase ore tonnage by 203 KTon per annum. To achieve the primary objective of increasing ore production by improving mining recovery, the study focused on predicting and controlling the movement of blasted ore to reduce spillage and enhancing the grade control model to reflect actual conditions post-blasting. Several alternative solutions were explored, primarily emphasizing drilling and blasting activities. Essential methods included capturing the actual blasting movement to adjust the ore block based on blasting design data and post-blasting muckpile topography. This approach minimizes ore loss by providing output as ore block adjustment based on post-blast movement data. In addition, the tie-up design was adjusted to control ore spillage outside the pit ridge. The implementation of these methods yielded significant improvements. Adjusting the ore block based on actual blasting movement contributed $1,545,764 in benefits. Controlling ore spillage outside the pit ridge achieved a 10% reduction in spillage, contributing $79,184 in benefits. These enhancements successfully met the 2022 mining recovery target of 96%, marking a 3% increase from 2021. Consequently, ore loss was reduced by 178 KTon throughout 2022, resulting in a financial impact of $7.3 million. The study underscores the significance of precise blasting techniques and effective spillage control in enhancing mining recovery rates.

Jan 21, 2025

By Stefan Zanon, Ty Faechner, Clayton V. Deutsch

Secondary data are important in geostatistical simulation of continuous variables. Geophysical data and geological trends are used for modeling porosity and permeability. Multiple mineral grades must often be modeled for mining applications. Sequential Gaussian simulation (SGS) is often used because of its relative simplicity and robustness. The two most common approaches to integrate secondary data in Gaussian simulation are with (1) locally varying mean, or (2) collocated cokriging. A significant problem with both of these techniques is variance inflation, that is, the variance of the resulting simulated values is too high because of an inappropriate decision of stationarity or an artifact of choosing a single secondary data in presence of many. We introduce a self-healing procedure for dynamic correction of this problem. The dynamic correction is different for the locally varying mean approach and for collocated cokriging since there are different reasons why each of these methods causes variance inflation. The reasons for variance inflation are discussed and the self-healing is applied to a number of data sets.

Jan 1, 2002

By Michael F. Tucker

Dealing successfully with intercultural issues is critical for success on an international assignment. This is true not only for employees but for the accompanying spouses and children as well. This paper presents a set of research-based competencies required for successful life and work in another country, such as open-mindedness, flexibility, and respect for the beliefs of others. Best practices for training employees and their families bound for international assignments are also presented.

Jan 1, 2001

By C.A. Zapfee, C. E. Sims

An investigation of the behavior of inclusions in steel several years ago1 led to the conclusion that some of the commonly occurring inclusions in steel have appreciable solubilities, particularly in liquid steel. In the belief that further study and clarification of this matter was warranted, a laboratory study of oxides in liquid steel was started. These oxides are generally the result of deoxidation treatment, and the basis of an understanding of their behavior must be, therefore, the behavior of the deoxidizer in liquid iron. The Fe-Si-O system was selected for the first study, and the apparatus used and experiments conducted are described herein. Apparatus The apparatus is shown in Fig. r and the system is shown by diagram in Fig. 2. Furnace, A lmosphere Commercial hydrogen (1) passes through an orifice (2) into a manometric system that measures the tankside pressure (3) and the back pressure (4) in the system. A water trap (5) guards against excess tankside pressure. A by-pass with stopcocks (6 and 7) is provided, so that the hydrogen can be routed directly from the tank to the furnace if desired. When stopcock 7 is closed and stopcock 6 is open, the gas proceeds through the conditioning train, of which the first unit is a furnace (8) that contains platinized asbestos at 350°C. The temperature is measured by a thermocouple and potentiometer (9) and is controlled by a slidewire resistance (10). In this furnace fres oxygen is converted to water vapor. The exiting gas passes over a water bath (11) kept slightly below boiling temperature by an auxiliary heating unit (12). This unit also heats a surrounding copper coil (13) containing water, and the heated water rises through a collar (14)

Jan 1, 1943

By C. A. Zapfee, C. E. Sims

An investigation of the behavior of inclusions in steel several years ago1 led to the conclusion that some of the commonly occurring inclusions in steel have appreciable solubilities, particularly in liquid steel. In the belief that further study and clarification of this matter was warranted, a laboratory study of oxides in liquid steel was started. These oxides are generally the result of deoxidation treatment, and the basis of an understanding of their behavior must be, therefore, the behavior of the deoxidizer in liquid iron. The Fe-Si-O system was selected for the first study, and the apparatus used and experiments conducted are described herein. Apparatus The apparatus is shown in Fig. r and the system is shown by diagram in Fig. 2. Furnace, A lmosphere Commercial hydrogen (1) passes through an orifice (2) into a manometric system that measures the tankside pressure (3) and the back pressure (4) in the system. A water trap (5) guards against excess tankside pressure. A by-pass with stopcocks (6 and 7) is provided, so that the hydrogen can be routed directly from the tank to the furnace if desired. When stopcock 7 is closed and stopcock 6 is open, the gas proceeds through the conditioning train, of which the first unit is a furnace (8) that contains platinized asbestos at 350°C. The temperature is measured by a thermocouple and potentiometer (9) and is controlled by a slidewire resistance (10). In this furnace fres oxygen is converted to water vapor. The exiting gas passes over a water bath (11) kept slightly below boiling temperature by an auxiliary heating unit (12). This unit also heats a surrounding copper coil (13) containing water, and the heated water rises through a collar (14)

Jan 1, 1943

By M. J. Michaud, M. J. Lavigne

"A cornerstone of any successful mining project is an understanding of the mineral assemblage and metal distribution comprising the deposit. Knowledge of the precise mineral/ metal zoning enables an operation to utilize different mining and processing methods optimized for different parts of the deposit. The Lac des Iles mine, located in northwestern Ontario, is one operation that depends on a good understanding of these issues. Current resources for the Roby Zone total 94.1 Mt grading 1.66 g/t Pd, 0.18 g/t Pt, 0.14 g/t Au, 0.062% Cu, and 0.053% Ni.The Roby Zone occurs within the gabbroic portion of the Lac des Iles intrusive complex and consists of three compositionally and texturally different ore types with variable PGE, base and precious metal contents. PGE occur as sulphides and bismuthotellurides in net-textured sulphides, coarse sulphide blebs and as finegrained inclusions within secondary silicates.Knowledge of the precise mineral/metal zoning has directly and indirectly improved several operational aspects, including resource modelling, mining, and processing. For example, metallurgical recoveries have been increased by up to 3% to 5% and concentrate grades have increased by up to 100%. IntroductionLac des Iles Mines Ltd., a wholly owned subsidiary of North American Palladium Ltd., owns and operates a 3000 t/d open pit mine and concentrate facility, located 100 km north of Thunder Bay in northwestern Ontario. The Lac des Iles PGE-gold-copper-nickel mine has been in commercial production since 1993 and in 1997, produced 1.8 million grams of palladium, 127 000 g of platinum, 114 000 g of gold, 438 000 kg of copper and 354 000 kg of nickel (North American Palladium Ltd., 1998).Under the Industrial Research Assistance Program (IRAP), a two-year study of the mineralogy of the Roby Zone was undertaken with a goal of improving the profitability of the mine. Geological mapping, petrography and geochemistry of the Roby Zone were completed during this study. Utilization of the detailed mineral/metal zoning identified as part of this study was implemented at the mine and shown to positively impact many operational aspects including mining and processing."

Jan 1, 2003

By J. B. De Hart

In the September issue of the Bulletin, 1923, there is a paper by J. A. H. Church on "The Spontaneous Combustion of Coal in Mines", which is more or less a general discussion of the subject. Mr. Church gives a list of mine fires which have occurred in Alberta. Of the total of thirteen fires, six are attributed to spontaneous combustion. Of these six fires, it will be noted that five are in thick pitching seams. These fires occurred in the following mines during the years shown, at Frank in 1909; at Lovett in 1916; at Cadomin in 1920; at Yellowhead in 1922, and at Cadomin in 1923. Every one of these fires has occurred, as Mr. Church points out, in a seam of over 12 feet in thickness, and furthermore not one of these fires has been extinguished, although in every case large sums of money were expended and considerable risks . taken in fire fighting. Now it is quite evident from these facts that mines working seams of this nature are faced with a very grave danger and it behooves us to study the matter and endeavor to arrive at some practical method of preventing the loss of our coal mines from this cause.

Jan 1, 1924

By S. Bantubani, I. Mc Dougall, S. Arjun, H. Joubert, R. Hansraj

The requirements determining the design of the Söderberg electrode columns used in base metal applications are different to those of other industries. There is a strong trend to position the contact shoes above the furnace roof in order to reduce the risk of water leakages directly onto the furnace bath. Tenova Pyromet has adapted its proven electrode column design for application on base metal electric furnaces based on these requirements. The design modifications implemented as well as considerations regarding the overall electrode-roof-furnace arrangement are discussed. Equally important is the management of the Söderberg electrodes to prevent over or under baking. Tenova Pyromet has developed the AutoFurn™ furnace controller to not only optimise furnace operations, but to improve electrode management. An overview of the electrode management control philosophy implemented by AutoFurn™ is provided, focusing on intelligent electrode regulation, slipping and baking. INTRODUCTION Tenova Pyromet has developed an electrode system for use in base metal furnaces, which builds on the experience that Tenova has gained during the past 30 years with electrodes in the ferroalloy and base metals industries. In base metals applications, an important safety consideration is the minimization of water within the furnace and on the furnace roof. In addition, direct contact between copper equipment such as contact shoes and pressure rings and the contents of the furnace is discouraged. In a 3 phase AC furnace, three electrode columns transfer the electrical energy to the furnace bath. Both Söderberg and prebaked carbon or UHP graphite electrodes are in use in base metal furnaces. In each column, the electrode is held in position by a hydraulic slipping and regulating device, a pressure ring and contact shoes. The electrodes can operate in a submerged-arc or brush-arc configuration, where the electrode is immersed in the slag or a short distance above the slag (Mc Dougall 2013). The electrode equipment is divided into an upper and a lower electrode assembly. The self-baking Söderberg electrode is made from lengths of steel casings that are added to the top of the electrode column and welded into place. Carbon electrode paste is added to the inside of these casings and is baked to form a solid tip in the region of the contact shoes. The working platform that surrounds the area where new electrode casings are added, is electrically isolated from the building and each electrode is isolated from the others to ensure the safety of the personnel who perform the electrode casing additions.

Jan 1, 2019

By Luis Vela Arellano

El presente texto describe la importancia de dos proyectos de exploración (Cotabambas y Antillas) en la producción de oro y cobre. Dichos proyectos se ubican en la franja del Balolito Andahuaylas-Yauri. La franja de edad Eoceno-Oligoceno representa el evento tectónico más importante que emplazó los más grandes depósitos de cobre en el planeta y se extiende desde el norte de Chile (Copiapó, Antofagasta, Iquique) hasta el sur del Perú (Apurímac y Cusco). En el lado de Chile, la exploración es antigua y los proyectos descubiertos ya se encuentran en explotación avanzada, mientras que del lado peruano, la exploración continúa y los yacimientos se encuentran en descubrimiento. Asimismo, se busca Mostrar el potencial de exploración y oportunidades de expansión en la región de Apurímac y Abancay.

Feb 1, 2015

By R. E. Head

[Surveys of the manganese situation conducted by the Geological Survey any other agencies have definitely established the, fact that the tonnage of high-grade manganese or in the United States is relatively small. It is therefore obvious that large-scale production of manganese is possible only through beneficiation of low-grade material. Deposits of low-grade manganese ore are being examined by engineers of the Mining Division of the Bureau of Mines to determine their size and possibilities as sources of manganese on a tonnage basis. The Metallurgical Division of the Bureau is developing and perfecting beneficiation processes with the objective of utilizing such low-grade ores. Microscopic study of these ores represents one phase of the research.]

Jan 1, 1941

By R. E. Head

[Surveys of the manganese situation conducted by the Geological Survey and other agencies have distinctly established the fact that the tonnage of high- grade manganese ore in the United States is relatively small. It is therefore obvious that large-scale production of manganese is possible only through beneficiation of low-grade material. ]

Jan 1, 1941

By I. K. Ozaydin

Analysis of piles groups loaded with large bending moments and both vertical and batter piles can be best performed by matrix analysis. In this paper, a case history about a tall marine control tower is presented. The soil conditions at the site and the results of the computer analysis of the piled foundation are summarized. It is shown that the pile loads are indeed less than the allowable load for a single pile. Pile head loads and moments are used in the analysis of the raft foundation.

Jan 1, 2010

By L. E. Schultze

The Bureau of Mines operated a mineral recovery unit to recover metal values from post-flash geothermal brines from the Salton Sea known geothermal resource area as part of its research into the use of plentiful resources. The brine was available for metals recovery after its heat content had been used to generate electricity. The brine source was treated with lime to precipitate the contained iron, manganese, lead, and zinc before injection of the heat-depleted brine into the underground reservoir. Data are presented on the effects of process variables, such as rate and method of lime addition and air oxidation versus air exclusion. Variations in precipitation of metal values, composition of precipitates, effectiveness of slurry thickeners, and methods of treating the precipitates to recover metal values are discussed.

Jan 1, 1982

By Igor Kuzymin, Isaak Maximov, Iuriy Akkerman, Galina Aksenova, Valentina Sentemova, Nataliya Trubechkova

"The Russian Federation possesses large reserves of oxidized ferruginous quartzites. These ores are currently mined together with magnetite ores and are stockpiled on account of unavailability of an efficient processing technology. This paper presents the results of investigations performed on the ores from the largest oxidized ferruginous quartzite deposit located in the Kursk Region iron-ore basin of Russia. The objective is to produce concentrate with iron content at least 66% and silica content within 5%. A processing technology was, developed under laboratory conditions, which included ore preparation, wet magnetic separation in weak and strong fields and reverse cationic flotation with addition of caustic soda, dextrin and Lilaflot 811M (alkoxy propylamine) collector from Akzo Nobel. The developed technology produced iron recovery concentrate with iron content of nearly 67%, and that of silica - 4.1%, iron recovery into concentrate being 72.6%."

Jan 1, 2014

By Scott Honan, Tassos Grammatikopoulos, Mike Johnson, Kelton Smith, Niels Verbaan, Ernesto Bourricaudy, Eric Larochelle, Rick Sixberry

"NioCorp is developing the niobium/scandium/titanium Elk Creek carbonatite resource deposit. The carbonatite phase contains significant niobium (0.71% Nb2O5), titanium (2.68% TiO2) and scandium (72 g/t) and is composed predominantly of calcite, dolomite and ankerite. Niobium is mostly (80%) contained in the pyrochlore and the balance in various Fe-Nb-Ti oxides, which also host most of the titanium. Scandium is distributed homogeneously throughout the ore mineral assemblage. The process flowsheet recovers separate niobium, titanium and scandium products. Scandium is extracted from whole ore hydrochloric acid leach solutions through solvent extraction, and is further refined through a re-leach and precipitation process. Scandium leach residues are treated with sulphuric acid to recover separate niobium and titanium precipitates. Both hydrochloric acid and sulphuric acid reagents are recycled within the flowsheet. This paper will discuss key bench and pilot test results (focusing on the scandium flowsheet) and will present a conceptual flowsheet developed by the project team for NioCorp at SGS Minerals.INTRODUCTION NioCorp is developing North America's only niobium/scandium/titanium project. The Elk Creek project is located near Elk Creek, Nebraska, and is the highest grade niobium project in North America and the largest prospective producer of scandium in the world. These elements are unique and valuable superalloy materials that are strategic and critical to many industries and national defense technologies. The project includes the Elk Creek Carbonatite (the Carbonatite) that intruded older Precambrian granitic and low to medium grade metamorphic basement rocks. Both the carbonatite and Precambrian rocks are interpreted to be unconformably overlain by approximately 200 meters (m) of Paleozoic marine sedimentary rocks of Pennsylvanian age. As a result of this thick cover, there is no surface outcrop within the Project area of the carbonatite, which was identified and targeted through magnetic surveys and confirmed through subsequent drilling. The available magnetic data indicate dominant northeast, west-northwest striking lineaments, and secondary northwest and north oriented features that mimic the position of regional faults parallel and/or perpendicular to the Nemaha Uplift."

Jan 1, 2017

By R. K. Jade

Although several studies in combining and bifurcating flows in two-way junctions and splits are reported, deviations persist in the estimated shock loss coefficients (SLCs). Due to their complex nature, more work has to be done to be able to correctly predict flow losses at these locations. In two-way splits, the flow at bifurcation is known to be characterized mainly by two recirculating zones in the downstream branches, whereas, in a junction one recirculating zone is observed immediately downstream of the main branch. The relative flow rate in the branches (quantity ratios) is treated as the only parameter defining the losses at these locations. However, the effect of wall roughness, if any, on SLCs becomes important for mine ventilation. This paper presents the critical determinants of shock losses at splits and junctions at varying quantity ratios. The flow at 90º split and junction was examined both experimentally and numerically for Reynolds number in the range of 1.0×104 to 1.6×105. With a well designed laboratory setup, using precision instruments, velocity and pressure measurements were carried out, by using two scales of wall roughness. 3D numerical simulations for these experiments were conducted by using ANSYS CFX modeling tool. CFD simulations yielded results that are reasonably close to experiments, providing high degree of satisfaction in numerically predicting losses across the splits and junctions. However, comparisons of these numerical simulation results with existing literature standards showed significant under-estimation of shock losses by the standard literature by as much as 50%. A clear rise in the magnitude of shock losses was noted in both the approaches, with increased wall roughness. Based on the current studies, predictor equations incorporating quantity ratios are developed for accurate estimation of shock losses. Further investigations on roughness are needed, before one is able to incorporate wall roughness into the prediction of SLC.

Jan 1, 2009

By Ian Bruce

Tailings and water management facilities are essential and integral components of mine and mill operations. They must be managed for the long term in order to ensure that safe and environmentally responsible stewardship is achieved. Toward this end, in 1998, The Mining Association of Canada (MAC) published A Guide to the Management of Tailings Facilities, which recommended the implementation of a tailings management framework (Figure 1) to integrate environmental and safety considerations into each stage of the life cycle of a tailings facility, from initial site selection and design, through construction and operation, to eventual decommissioning and closure. By February 2000 it was becoming apparent that while mining companies were making significant progress toward implementing and documenting tailings management systems, and integrating them with overall environmental management systems, further effort was warranted in their application at the operational level. In particular, a need was identified for further guidance in preparing manuals that outline procedures for the safe operation, maintenance and surveillance (OMS) of tailings and water management facilities.

May 1, 2002

By G. S. Scott, G. W. Jones

"INTRODUCTION In the course of the investigation the Bureau of Mines is carrying on to determine the causes, behavior, a. control of mine fires, the detection of incipient heating underground in the mines and above ground in refuse banks has received consideration.Many of the anthracite fires have been active for years and have progressed considerable distances free their original source.Some of the fires are in inaccessible territory, and it is often impossible to determine with any degree of accuracy their exact location or even the veins of coal that are afire, especially when the fire is in the upper strata and when it is impossible to go underground because of flooded conditions or the presence of an irrespirable atmosphere.In such cases, the only means by which the trend of a fire may be ascertained (as a result of any fire-fighting methods that may have been employed) are the sampling, exanination, and interpretation of the gaseous products coming from the fire area. The most important information desired is to know whether the temperature in the heated area is increasing or decreasing and to determine whether a fire that has been sealed is cooling down to normal mine temperatures or is maintaining its heat or is increasing in intensity due to infiltration of outside air.Interpretation of the analyses of gaseous products from refuse banks on the surface also should be of value in combating such fires. Refuse bank fires, with the additional danger of starting an underground fire through ignition of the outcrop, are by no means unknown in the anthracite coal region, and the causes of such fires are not always apparent. In a few cases the causes have been strongly suggestive of spontaneous origin."

Jun 1, 1938