Search Documents

By W. C. Morgan

Recently passed federal strip mining legislation officially emphasizes that the increased coal production required by this country through surface mining is going to be obtained only with stricter environmental standards. Dozing overburden down the hillside in Appalachian contour mining or leaving drag1ine spoils in area mining is now taboo and it is now or will soon be necessary to return the disturbed land to as good or better condition than before mining. These new restrictions will create a need for new and better ways to do the job. This paper describes one approach for utilizing scrapers and dozers to strip all of the overburden and to replace that overburden in an environmentally satisfactory fashion. The objective was to do this at a lower cost than that possible with the traditional dragline system using dozers and scrapers for reclamation and topsoil handling. In area stripping, the dragline has been able to move overburden at an extremely low cost. Operating costs of 8-13¢/bcy are typical in many operations where rehandling is not required. However, the cost of leveling the spoil piles and rehandling topsoil add considerably to the low basic cost of drag1ine stripping.

Jan 1, 1977

By M. S. Seehra, R. S. Pandurangi

"Investigations of the infrared spectra of crystalline and amorphous silica particles of different sizes (0.05, 5, 10, 15, 30, 45, and 260 um) in the range of 400-4000 cm-1 using Fourier transform infrared/photoacoustic spectroscopy we reported. The change in the intensity I of the signal with porosity e of powders follows the e/(1 - e) dependence for strong bands and e dependence for weaker bands as pre¬dicted by the theory of McGovern of al. For strong bands, I also follows the empirical relation I ~ D-n, where D Is the particle diameter in cm and n = 0.34-0.42. The anomalous positive frequency dependence of I on the modulation fre¬quency f observed for the stronger bands in the 45-pm and 260-pm particles Is believed to result from saturation. Some observations on the effect of changing the background from (carbon black) powder to pellet are also made.INTRODUCTIONSince the publication of the Rosencwaig—Gersho (RG) theory on the photoacoustic effect in solids (1, 2), Fourier transform infrared/photoacoustic spectroscopy (FTIR/PAS) has become an important technique for obtaining the IR spectra of surfaces and materials in their natural state (1-12). In the one-dimensional RG theory, the incident radiation, modulated at frequency f, is absorbed by the material to a depth pp = 1/B (B = absorption coefficient), thus setting up temperature variations in the material. These variations heat the adjacent gas/solid interface leading to the pressure fluctuations of the gas above the sample, which in turn is detected by microphone as a PA signal. The thermal wave originating from no deeper than the thermal diffusion length(2k/npcf) 1/2 in the material contributes to the PA signal (here k, p, and c are respectively the thermal conductivity, density, and specific heat of the material). Since u2, can be varied by varying the experimental parameter f, depth pro¬filing by PAS is possible and a number of papers on this subject have appeared in recent years (2-10). Another im¬portant phenomenon is saturation which occurs when the material thickness 1> u> us (1-12).The original promise of PAS for use with powder samples, without the need to ""prepare"" samples as in FTIR spectros-copy, has not yet been fully realized because of several com¬plications. Theoretical works by Monchalin et al. (13) and McGovern et al (14) showed that the interstial gas in the voids of the powders can act as amplifier and that, for the same mass, a finer powder is expected to yield higher PA signal than a coarser powder. Although in a number of earlier studies (15-21) an increase of PA signal with decreasing particle size has been observed, a quantitative check on the equations developed by McGovern et al. (14) has not yet been made. It is necessary to understand the particle size effects in PAS if the promise of PAS for IR spectroscopy of powders is to be realized. In this paper, we report results of a detailed study on the PAS of silica powders for the particle size range of 0.05-260 um and compare the results with theory (14). We have also investigated the frequency dependence of the variousIR modes in these powders and show that the saturation phenomenon affects at least some of the observations. Some observations on the effects of pellet vs powder background are also reported (22-24). Details of these findings are presented and discussed in this paper."

Jan 1, 1990

By Unknown

Threats to Industry Theft Potential

Jan 1, 2006

By M. Saunders Macdonald

A number of open pit gold mines in Nevada extract ore from areas below natural groundwater elevations, necessitating dewatering and some method of disposal of the extracted water. These open pits extend well below the water table, with associated dewatering volumes greater than 10,000 gpm. Some mines, with large volumes of dewatering water to manage, have constructed re-infiltration basins to re-introduce dewatering water to the groundwater system some distance from the pits. This paper presents an overview of the state of the art of re-infiltration projects, including the permit process for such projects in Nevada, and the necessary engineering considerations.

Jan 1, 1996

By Stanley M. Moos

The Pueblo Viejo gold/silver mine, located in the Dominican Republic, started production in early 1974 processing ores averaging 4 g/tonne gold and 20 g/tonne silver at a rate of 7,250 tonnes/day. The ore milled is a silicified siltstone with average work index of about 8 that occurs as an extensive oxide capping of a primary sulfide orebody. The sulfide ores are refractory to conventional treatment process and extensive research work is now in progress to develop a treatment process for them. The ore deposit has a long history having been mined by the indigenous Arawak Indians (for some time in the early sixteenth century) prior to the arrival of the Spanish and then by the Spaniards. In the early 1950?s, Italian engineers attempted to process the sulfide ores. Mining by the Indians and Spanish was abandoned because of low grade and little coarse gold in the oxide ores and by the Italians because of the refractory nature of the sulfide ore. In 1969, Rosario Resources geologists discovered that there existed sufficient reserves of oxide ore for a viable mining operation and accordingly, the plant was designed, built and brought into production.

Jan 1, 1979

By Allen H. Rogers

THE need for coordinated effort on public problem by engineers has long been felt. Early in June there will assemble in Washington a conference composed of delegates from all the engineering organizations in the country. The call for this conference is issued by the Joint Conference , Committee of the four national societies as the completion of its work on the organization of a congress composed of delegates representing all the engineering organizations of the United States. The plan for this confederation was presented at a joint meeting of the administrative boards of the national founder societies on Jan. 23, 1920; and was unanimously approved in principle by that meeting. The work of the committee since that date has consisted in drafting a constitution of the organization to be presented at the conference for discussion and, after such amendments as may be adopted, acceptance.

Jan 1, 1920

By Laxman S. Sundae

In the vast majority of American coal mines, roof bolt holes are drilled dry, mainly because of mine operator concern with the spent water creating adverse working conditions. Wet drilling, however, can increase drilling rates and the effective lifetime of the drill bits used. This study, carried out as part of an ongoing cooperative research program between the U.S. Bureau of Mines and the University of Missouri-Rolla, shows that the large volumes of water conventionally used in wet drilling are not necessary, and the performance benefits from wet drilling can be achieved with total volume flows on the order of 0.4 L per hole. This conclusion is validated based on the measured respirable dust generated in drilling Berea sandstone. The results are confirmed using a variety of bit shapes, which are also shown to have a significant effect on penetration rate.

Jan 1, 2010

By Warder A. Shaver

INTRODUCTION Mine No. 95 of the Consolidation Coal Co., a divi¬sion of Continental Oil Co., is located in Shinnston, WV. Mine No. 95 was opened in January 1967 and has been operating continuously since that time. The mine has 544 hourly and salaried employees. In 1974 this mine was the largest coal producer in West Virginia. Opera¬tions include two longwall sections and eight Marietta Borer continuous miners. Originally there were also two Jeffrey Heliminer continuous miners, but use of these was discontinued in June 1978. Production averages 12 727 t/d (14,000 stpd). Two portals now service the mine with a third portal proposed for 1978. GEOLOGY Mining takes place in the Pittsburgh coal seam which dips 0.04 rad (21h°) northwest. The working seam is steam coal with an average height of 2.2 m (86 in.). Immediately above the seam, the overburden is com¬posed of 6.1 m (20 ft) of shales followed by 6.1 m (20 ft) of weak sandstone and 51.8 (170 ft) of shaley limestone. The shale weathers when exposed to mois¬ture. Surface water has been a problem due to a fire¬clay floor which turns to paste when mixed with water. GENERAL DESCRIPTION The present mining plan for Consol's No. 95 mine has a proposed life of 35 to 40 years. One set of main headings has been driven in the north direction and one set in a western direction. These are the areas in which the majority of the virgin coal lies. The panels are driven off of the mains at 2134 to 3048-m (7,000 to 10,000-ft) intervals. The continuous mining sections are set up 133 x 610 m (600 x 2000 ft). Longwall sections are 259 x 1220 m (850 x 7000 ft). All of these mining sections are retreating uphill. Development is with continuous miners. A Marietta Borer miner is used for the main development work. These miners cut 4.1 m (13 ft 6 in.) wide and 2.1 m (7 ft) high, leaving an arch cut. Along with the arch, a 152.4-mm (6-in.) thick layer of roof coal is left in place to protect the roof from weathering. The combi¬nation of the self-supporting arch and the roof coal al¬lows the entries to be driven 30.5 m (100 ft) without bolting. Full bolting, however, is carried outby the last open crosscut. This bolting is done on 1.5 x 1.5-m (5 x 5-ft) centers using 1.5-m (5-ft) long roof bolts with tandem anchors and 152.4-mm (6-in.) steel washer plates. When needed, crib blocks with a 50.4-mm (2-in.) drill hole are used as supplemental supports. Three-hole steel channel with the ends curved down¬ward to conform to the borer arch may also be used. In the mining sections, a 14 BU loader is used be¬hind the Marietta miner to load two Torkar shuttle cars. These haul to Long-Airdox feeder breakers which load onto a 1.07-m (42-in.) wide conveyor belt. With the exception of the shuttle cars, which use 275-V d-c power, the face equipment operates on 550-V a-c power. The main power line is 7200 V ac. The same loading and hauling equipment is used with the Marietta Borer miner for driving both panel and development entries. In the retreat sections, the same equipment with the exception of the miner is utilized. Because of the advantage of a variable cutting hight, Jeffrey Heliminer ripper-type continuous miners were employed in these retreat sections. For longwall mining the first unit uses an Eickoff EDW 300-L double-drum ranging shearer. Drum di¬ameter is 1.69 m (66 in.) with a drum rotation speed of 45 rpm. The drum is equipped with 48 Carmet 34-L-1 bits. The 300-kW (400-hp) motor operates on 1000 V. Tramming of the shearer head is done through a hydraulically driven 26-mm wide chain. Maximum cutting speed is 7.93 m/min (26 fpm), and maximum tram speed is 12.8 m/min (42 fpm) with an average cutting speed of 3.66 m/min (12 fpm). Web cutting depth is 762 mm (30 in.) and the cutting height is 2.13 m (7 ft). The conveyor width is 686 mm (27 in.). It uses a single chain, 26 mm thick, with flights on 0.91-m (3-ft) spacing. The face conveyor speed is 64.3 m/min (211 fpm) when driven by two 112-kW (150-hp) 1000-V Louis Allis motors through torque convertors. The roof support used is Gullick Dobson chocks [6-legged 77.3 t (85 st) per leg, 463.6 t (510 st) total capacity] with double-acting leg jacks. The hydraulic pressure for the legs is 13.8 MPa (2000 psi), and the hydraulic pressure for rams is 6.8 MPa (1000 psi). The yield valves are set at 57.8 MPa (8500 psi). Each chock weighs 4.09 t (4.5 st). The stage loader is an Eickoff drive, with a 68-kW (90-hp), (00-V Reliance motor. A 26-mm thick single strand chain with flights on 0.6-m (2-ft) centers runs at 75.89 m/min (249 fpm). The stage loader is self-advancing and is connected to the belt tail piece with a special fifth wheel attachment so that the stage loader can advance and guide the tail piece. The hydraulic pressure for the roof support is supplied by two 45-kW (60-hp) Reliance motors op¬erating on 699 V, with 1.26 L/s (20 gpm) constant volume Gullick hydraulic pumps. Each pump services alternate chocks, with the two pressure lines connected at the tailgate by 25.4-mm (1-in.) hydraulic hoses, rated at 27.21 MPa (4000 psi). The 6.8 MPa (1000 psi) pressure rams advance is supplied by a 45-kW (60-hp), 600-V Reliance motor and a 1.26-L/s (20-gpm) con¬stant volume Gullick pump. Return lines are 35.5-mm (1.4-in.) diam hydraulic hoses with rated capacity of 27.21 MPa (4000 psi). The fluid used in the hydraulic system consists of 95% water and 5% Hy-chock fire resistant water soluble oil. Water is stored and mixed in a 6096-L (2000-gal) track-mounted tank and goes to a 655-L (180-gal) reservoir at the pump. The belt conveyor structure is 1.07 m (42 in.) wide with 0.47 rad (27°) idlers, bottom stands located on 3.05-m (10-ft) centers, top stands on 1.5-m (5-ft) centers, and is supported on a 19-mm (3/4-in.) diam

Jan 1, 1982

By D. W. Fuerstenau

Measurement of zeta potentials is a useful tool to study the surface chemistry of minerals under flotation conditions. Because there is continued interest in this approach, the apparatus for obtaining zeta potentials of nonconducting solids by the streaming potential method is outlined here. Fig. 1 illustrates the streaming potential apparatus. The streaming potential cell or plug consists of two 24/40 standard ground joints (4) joined with a piece of pyrex tubing 60 mm long and 12 mm in diam (5). The electrodes are made of bright platinum disks 19 mm in diam and 1 mm thick through which 0.5-mm holes have been drilled (6). To the surface of each is welded a piece of 80-mesh platinum gauze. Each electrode is permanently mounted on the ends of the inner parts of the two standard joints by means of a platinum wire (7) which connects it to the tungsten seal at the end of the cell (8). For ease in cleaning and handling the apparatus, the streaming cell is fastened to the 500-ml reservoir flasks (1) by means of two 18/9 ball and socket joints (2). This particular arrangement permits passage of the solution in either direction through the plug of particles. Flow of solution can be stopped by a stopcock (3). One of the reservoir flasks has a large opening to permit insertion of either a thermometer or a pair of electrodes for measuring pH of solutions within the system. In making the experiments, the plug is filled with 48 to 65-mesh particles, but a layer of 28 to 35-mesh particles is placed at each electrode to prevent any of the finer particles from passing through holes in the electrodes.

Aug 1, 1956

By William R. Webster

The unusual interest taken in the papers on steel at the New York (1922) meeting showed that the time is ripe for the renewal of the general discussion of the physics of steel, on the same lines that wete used formerly and produced such good and lasting results. The curves shown in Figs. 1 to 4 and the appendix were added to my paper1 after the February meeting, but, unfortunately, Figs. 1 and 3 were transposed; the curves on page 252 are for bessemer steel and belong on page 254; while those on page 254 are for open-hearth steel and belong on page 252. These errors are evident at once on referring to the data in Tables 1 and 2, pages 227 and 228. The curves for each 0.05 per cent. of carbon and manganese in basic open-hearth steel are given in Figs. 1 and 2; these lines for the lower carbons and manganese are comparatively uniform. Figs. 3 and 4 give similar lines for carbon and manganese in bessemer steel. The large break in the carbon lines from 0.55 per cent. to 0.60 per cent. is caused by much higher silicon in the steels of 0.60 per cent, carbon and over that are used for springs, etc. The estimated ultimate strength of pure iron, and the increase in strength by carbon, phosphorus, and manganese, with the different views regarding the same, were given and diseussed. All of this can be considered as an introduction to the practical use that is now being made of such data in selecting the heats of steel best suited to give the required physical tests called for in the finished rolled material. The chemical composition of the steel, of course, tells only a part of the story, as many other factors that have an influence on the physical properties of the steel must be considered, and controlled as far as is possible. Some of these have already been referred to, but there are other important ones to be considered and discussed.

Jan 1, 1923

By William R. Webster

The unusual interest taken in the papers on steel at the New York (1922) meeting showed that the time is ripe for the renewal of the general discussion of the physics of steel, on the same lines that wete used formerly and produced such good and lasting results. The curves shown in Figs. 1 to 4 and the appendix were added to my paper1 after the February meeting, but, unfortunately, Figs. 1 and 3 were transposed; the curves on page 252 are for bessemer steel and belong on page 254; while those on page 254 are for open-hearth steel and belong on page 252. These errors are evident at once on referring to the data in Tables 1 and 2, pages 227 and 228. The curves for each 0.05 per cent. of carbon and manganese in basic open-hearth steel are given in Figs. 1 and 2; these lines for the lower carbons and manganese are comparatively uniform. Figs. 3 and 4 give similar lines for carbon and manganese in bessemer steel. The large break in the carbon lines from 0.55 per cent. to 0.60 per cent. is caused by much higher silicon in the steels of 0.60 per cent, carbon and over that are used for springs, etc. The estimated ultimate strength of pure iron, and the increase in strength by carbon, phosphorus, and manganese, with the different views regarding the same, were given and diseussed. All of this can be considered as an introduction to the practical use that is now being made of such data in selecting the heats of steel best suited to give the required physical tests called for in the finished rolled material. The chemical composition of the steel, of course, tells only a part of the story, as many other factors that have an influence on the physical properties of the steel must be considered, and controlled as far as is possible. Some of these have already been referred to, but there are other important ones to be considered and discussed.

Jan 1, 1923

By D. K. Deardorff

The hafnium-vanadium phase diagram was constructed within an estimated accuracy of ± 10° C and ± 2 wt pct composition. Alloys for investigation were melted under an atmosphere of purified helium by nonconsumable tungsten-electrode arc melting on a water-cooled copper hearth. Melting points were determined by optical pyrometer, and the remaining phase relationships were investigated by metallography, thermal analysis, and X-ray diffraction. The existence of a face-centered cubic intermetallic compound HfV2 (a = 7.38 A) was confirmed. A eutectic reaction occurred at 20 wt pct vanadium and 1,395° C to yield HfV2 and 8 solid solution. HfV2 melted incongruently by a peritectic reaction at 1,480° C, and the 3 solid solution decomposed eutectoidally at 1,165° C and 6 wt pct vanadium to yield HfV2 and a solid solution. The eutectoid, the eutectic, and the peritectic isotherms extended from 1 to 36.3 wt pct vanadium, from 8 to 36.3 wt pct vanadium, and from 26 to 89.5 wt pct vanadium, respectively. Terminal solid solubilities of hafnium in vanadium at 1,300° C and of vanadium in hafnium at 1,100° C determined to be about 3 and 1 wt pct, respectively.

Jan 1, 1965

By D. R. Lentz, J. A. Walker

"Abstract -The Flat Landing Brook Zn-Pb-Ag deposit of the Bathurst Mining Camp occurs within a narrow thrust-bound nappe containing felsic volcanic and volcaniclastic rocks of the Tetagouche Group. Within the host nappe, the Tetagouche Group is represented by the Nepisiguit Falls Formation and the overlying Flat Landing Brook Formation. The Nepisiguit Falls Formation is divided into two members: quartz- and quartz-feldspar-phyric volcaniclastic rocks ± minor lavas (Grand Falls member), and aphyric, fine-grained volcaniclastic rocks (Little Falls member). The Flat Landing Brook Formation consists of aphyric rhyolite flows and interbedded pyroclastic rocks. Several gabbroic intrusions occur in both the footwall and hanging-wall sequences. These gabbros locally cut out the mineralized horizon at shallow levels, and are considered to be feeders to tholeiitic basaltic flows (Forty Mile Brook member) of the Flat Landing Brook Formation. The Flat Landing Brook deposit has many of the characteristics typical of volcanogenic massive sulfide deposits occurring within the highly productive Nepisiguit Falls Formation in the eastern part of the Bathurst Mining Camp. Mineralization occurs within or at the top of the Grand Falls member and comprises four or more massive to semi-massive sulfide lenses that vary in thickness between 3 and 5 m. Massive lenses are laterally gradational to, or underlain by, zones of disseminated sulfides up to 38 m thick. The deposit contains an estimated resource of 1.7 Mt grading 4.9% Zn, 0.94% Pb, and 19.54 g/t Ag to a depth of approximately 150 m. From 150 to 300 m below surface, mineralization is low grade and mostly disseminated. However, below 300 m, ore-grade (>10% Pb+Zn) massive sulfide lenses have been intersected over mineable widths. Oxide facies iron formation overlies and (or) grades laterally into the sulfide lenses. The oxide facies has strong positive Eu anomalies and gently sloping rare earth element (REE) profiles suggesting that it was formed from relatively hot acidic fluids that had interacted with felsic volcanic rocks in the footwall. In contrast, the silicate facies iron formation that is more distal to sulfide accumulations has very weak positive Eu anomalies and gently sloping REE profiles, suggesting either cooler hydrothermal fluids or dilution of the hydrothermal component by detrital material. Hydrothermal alteration has affected most footwall rocks. Most notably, albite-destructive alteration has resulted in Na2O depletion, whereas mass addition of K2O is manifested in the formation of sericite (white mica). In more intensely altered quartz- and feldspar-phyric volcaniclastic rocks of the Grand Falls member, feldspar destruction is accompanied by chlorite alteration, producing quartz-phyric rocks similar to those in the footwall of many Bathurst Camp deposits."

Jan 1, 2006

By W. Weissberger, Frankiewicz, L. Pommier

Introduction In the U.S., about one-quarter of the fuel oil and natural gas consumption is associated with power production in utility and industrial boilers and process heat needs in industrial furnaces. Coal has been an attractive candidate for replacing these premium fuels because of its low cost, but there are penalties associated with the solid fuel form. In many cases pulverized coal in unacceptable as a premium fuel replacement because of the extensive cost of retrofitting an existing boiler designed to burn oil or gas. In the cases of synthetic fuels from coal, research and development still have a long way to go and costs are very high. Another option, which appears very attractive, is the use of solid coal in a liquid fuel form - coal slurry fuels. Occidental Research Corp. has been developing coal slurry fuels in conjunction with Island Creek Coal (ICC), a wholly-owned subsidiary. Both coal-oil mixtures and coalwater mixtures are under development. ICC is a large eastern coal producer, engaged in the production and marketing of bituminous coal, both utility steam and high quality metallurgical coals. There are a number of incentives for potential users of coal slurry fuels and in particular for coal-water mixtures (CWMs). First, CWM represents an assured supply of fuel at a price predictable into future years. Second, CWM is available in the near term; there are no substantial advances in technology needed to provide coal slurry fuels commercially. Third, there is minimal new equipment required to accommodate CWM in the end-user's facility. Fourth, CWM is nearly as convenient to handle, store, and combust as is fuel oil. Several variants of CWM technology could be developed for different end-users in the future. One concept is to formulate slurry at the mine mouth in association with an integrated beneficiation process. This slurry fuel may be delivered to the end-user by any number of known conveyances such as barge, tank truck, and rail. Slurry fuel would then be stored on-site and used on demand in utility boilers, industrial boilers, and potentially for process heat needs or residential and commercial heating. An alternative approach is to formulate a low viscosity pre-slurry at the mine mouth and to pipeline it for a considerable distance, finishing up slurry formulation near the end-user's plant. Finally, at the other extreme of manufacturing alternatives, washed coal would be shipped to a CWM manufacturing plant just outside the end-user's gate. Depending on fuel specifications and locations of the mine and end-user facility, any of these alternatives may make economic sense. They are all achievable in the near term using existing technology or variants thereof. The Coal-Water Mixture CWMs contain a nominal 70 wt. % coal ground somewhat finer than the standard pulverized ("utility grind") coal grind suspended in water; a complex chemical additive system gives the desired CWM properties, making the suspension pumpable and preventing sedimentation and hardening over time. Figure 1 shows the difference between a sample of pulverized coal containing 30 wt. % moisture and a CWM of identical coal/water ratio. The coal sample behaves like sticky coal, while the CWM flows readily. The combustion energy of a CWM is 96-97% of that associated with the coal present, due to the penalty for vaporizing water in the CWM. Potentially any coal can be incorporated in the CWM, depending on the combustion performance required and the allowable cost. CWMs are usually formulated using high quality steam coals containing around 6% ash, 34% volatile matter, 0.8% sulfur, 1500°C (2730°F) initial deformation temperatures, and energy content of 25 GJ/t (21.5 million Btu per st). Additional beneficiation to the 3% ash level can be accomplished in an integrated process. There are a number of minimum requirements which a satisfactory CWM must meet: pumpability, stability, combustibility, and affordability. In addition, a CWM should be: resistant to extended shear, generally applicable to a wide variety of coals, forgiving/flexible, and compatible with the least expensive processing. It was found that a complex chemical additive package and control of particle size distribution are necessary to achieve these attributes simultaneously, while maximizing coal content in the slurry fuel. Formulation of Coal-Water Mixtures A major consideration in the manufacture, transportation, and utilization of a slurry fuel is its pumpability, or effective viscosity. Most CWM formulations are nonNewtonian, i.e., viscosity depends on the rate and/or duration of shear applied. Viscosities reported in this paper were obtained using a Brookfield viscometer fitted with a T-spindel and rotated at 30 rev/min, thus they are apparent viscosities measured at a shear rate of approximately 10 sec-1. The instrument does reproducibly generate a shear field if spindle size and rotation rate are held fixed. By observing the apparent viscosities of several slurries at fixed conditions it is possible to obtain a relative measure of their viscosities for comparison purposes. A true shear stress-shear rate relationship at the shear rates at which the CWM will be subjected in industry may be obtained using the Haake type and a capillary viscometer. These viscometers are used for specific applications. However, for comparison purposes, apparent viscosities are reported.

Jan 1, 1985

By Gerald W. Elger

Research at the Albany Metallurgy Research Center has shown that high-purity rutile can be produced from relatively low-grade ilmenite obtained from a massive rock deposit. Ilmenite is first smelted in an electric-arc furnace to separate the iron and produce a slag enriched in titanium dioxide. Titania slag mixed with a phosphate flux is then oxidized to synthesize rutile and form a phosphate-glass matrix which contains the impurities. Attrition scrubbing the treated slag in dilute solutions of phosphoric or sulfuric acid liberates the rutile, which is concentrated by physical methods. Tests show that synthesized rutile containing 95 to 97 pct titania responds to chlorination at the same rate as natural rutile.

Jan 1, 1973

By J. Kretschmann

Southeast Asian countries cannot maintain their economic growth rate without the development of their mining industries. To make this development as sustainable as possible requires sound fundamentals securing not only economic progress and environment protection but also improvements in occupational safety and health (OSH) for the miners. Mining in South East Asia is still very labor intense and dangerous. Tremendous achievements from world class mining operations in advanced mining countries can be used as role models to improve the status quo of the Southeast Asian countries in OSH management. Know-how transfer, therefore, is a key factor for major improvements. Effects of this transfer based on a multi-level approach will be discussed based on a case study. It describes the transfer from German to Vietnamese hard coal mining industry. Crucial requisites for excellent achievements in OSH in Southeast Asian mining countries are also mentioned.

Feb 23, 2014

By I. Jashnani, J. R. Lawter, D. B. Lindsay

INTRODUCTION It is a generally recognized obligation of owners and operators of underground mines in the United States to protect the health of miners against the potential carcinogenic effect of airborne alphaemitting radionuclides, in particular the shortlived radioactive daughter-products of 222Rn. In meeting this obligation, a number of strategies are available, and it is largely up to the operator to decide what combination of methods he will use. Because the officially accepted theory of the mechanism by which radon and its short-lived progeny cause cancer of the respiratory system, the objective in controlling this health hazard is to limit as far as possible the inhalation of the three daughter products, 218Po, 214Pb, and 214Bi. (214Po, the fourth nuclide in the chain, is so short-lived that its alpha-decay occurs almost instantaneously after the beta-decay of its parent, 214Bi.) The reasoning in this theory leads to the conclusion that the alphadecay of radon itself causes essentially negligible physiological damage, and that the amount of daughter product activity attributable to decay of radon within the respiratory system is also very small. As every ventilation engineer in this business knows, however, focusing remedial actions exclusively on the daughter products themselves is choosing the hard way, and will probably never lead to effective control of this health hazard in underground mining activities. The reason for this troublesome fact can be seen in Figure 1. Let us say that we have air containing 222Rn and its short-lived daughters in near-equilibrium, a not-uncommon condition in the air of a poorly ventilated underground mine, and that we wish to purify it by removing only the toxic daughter products. If we have been very thorough in our purification efforts, we might expect to achieve a 99% reduction of the Working Level (WL) measurement. Figure 2 allows us to examine closely the early regrowth of WL's in this freshly cleaned air. Within the first five minutes, for instance, the WL's are back to 10% of their full equilibrium value, and ten minutes later the level has more than doubled and is on its way to an almost complete defeat of the clean-up effort by the end of the next hour. It is quite clear from this simple illustration that no matter how effective an air-cleaning system may be if it is directed only at the selective removal of the toxic trio, 218Po, 214Pb and 214Bi, its beneficial effect will be quite temporary. A truly effective attack on the problem must always include methods aimed at the control of the unruly parent, radon. Then, even if its progeny have an inalienable "right to life", their brief lives will not be spent in the miners' lungs. The object of the present paper is to show how state-of-the-art environmental air

Jan 1, 1981

By J. Rogans

This paper discusses the comparative performances of the three activated carbon adsorption circuits at the West Wits operations of Anglogold. These circuits consist of two pump-cell circuits (at Two Plant, formerly Elandsrand and at Three plant) and a conventional counter-current adsorption circuit (at Mponeng plant). The implications of the improved performance of the pump-cell plants are discussed.

Jan 1, 2002

By Sean E. Armstrong, Deepak Malhotra

Gold extraction from refractory ores as a percentage of total gold production is increasing. The processing technology options for treating difficult-to-process refractory ores are also increasing. The best processing option is dependent on many factors including feed grade and the cause for ore refractoriness. The causes for ore refractoriness are many foldCpreg-rob­bing, encapsulation in pyrite, arsenopyrite or silica, presence of cyanocides, presence of cyanide-insoluble gold compounds, etc.1. The first step in the process development of a refractory gold deposit is to determine the cause for ore refractoriness. The traditional approach of undertaking detailed mineralogical examination of ore types, major and minor mineral constituents and their association does not necessarily provide the metallur­gist all the information needed for characterization of gold-bear­ing ores. For process development programs it is desirable to complement traditional mineralogical methods with diagnostic leach testing, which attempts to quantify the deportation of gold in various mineral matrices. This paper briefly reviews the diagnostic leaching proce­dures and its applications for a wide range of gold-bearing refractory ores, both primary and by-product.

Jan 1, 1996

By P Pieterse

Kumba Iron Ore Ltd is currently commissioning the Sishen Expansion Project (SEP) û a brownfields project on the Sishen Iron Ore Mine located in the Northern Cape Province, South Africa. SEP is designed to produce 13 Mtpa of product from 21.7 Mtpa of ROM feed. The beneficiation section of SEP employs jigs to process narrow size fractions in the 25 x 0.8 mm size range. The -0.8 mm fraction is screened out ahead of the jig plant and rejected as waste without any prior beneficiation. The processing of this fraction was not included in the early stages of SEP development because no suitable beneficiation or dewatering technologies could be identified within the time-frame required to implement SEP. This paper presents the SEP 1B project, ie the metallurgical and process engineering study that was done to evaluate the techno-economic viability of processing the -0.8 mm material of SEP. To support this evaluation, metallurgical bench scale testwork was done on selected samples characterising the material types used in the SEP for gravity concentration beneficiation. Subsequently, pilot testwork on a 300-ton bulk sample demonstrated that an integrated teeter-bed/spiral circuit could be used to successfully beneficiate the -0.8 mm fraction. The study has established the viability of the proposed process and has concluded that approximately 390 000 tpa could be produced and added to the SEP fine ore product without violating the applicable product specifications. The proposed process has been designed to be implemented in modular units in order to facilitate implementation and ensure future expandability. Based on the recommendations of the study, approval has been granted for the detail design feasibility study. Production is scheduled to commence in the first quarter of 2010.

Jan 1, 2008